Replaced print head PhotosmartPlus 210 has; still no black

When printing, black does not show. I followed the instructions in the troubleshooting online. I have cleaned the print heads, bought a new print head and installed it. Now, the message reads: "line up failed." How can I fix this?  Fine color prints. Black is still missing. I use new cartridges. I've recently upgraded to Mavericks and wonder if that's part of the problem. I have Photosmart Plus 210 has.  I would like to resolve the problem before giving up and buying a newprinter.

HP printer does not print.  Installing the new blak cartridge

Tags: HP Printers

Similar Questions

  • Photosmart Pro B9180 'Replace due to defective print head' WARNING

    My B9180 gave me the msg "replace the defective print head" after a period of inactivity.  I'm using Snow Leopard on a Mac Pro 10.6.8.  The printer went through several periods of non-use, since I bought it used, but almost nine.  Usually, I experience white lines in my impressions after using the printer, I've always been able to fix by cleaning of the nozzles and/or the print heads, either automatically, or manually.  The last round resulted in the warning "defective printhead" even after repeated manual cleaning.  In fact, the process to put off the printer and back, with and without unplugging it, led to 'replace' warnings for ALL the printheads several times, only 2 print heads a couple of times a moment seems to be giving me just the consistantly 'replace magenta/yellow print head.  The strip of plastic that surrounds the ink nozzles is loose to the point of current on the PH.  My printer is no longer under warranty, but before I spend money on phone support and new print heads, I want to look at other possibilities.  The book says that if the manual cleaning of the printheads does not, HP support should be contacted, suggesting that there could be other possible remedies, before you buy new print heads.   I wouldn't begin to buy new print heads to find that again, they will not work because of some other problem.  I am also concerned by the other warnings of print head, even if they did not intervene now.

    Also, opening lid for cleaning of the PH, I noticed a lot of ink accumulate in 4 coarse foam pads, each in its own little tray located inside the printer on the right side.  some of them were overflowing. / I carefully daubbed a part of the ink with q-tips, but I wonder if this condition could be or cause problems.

    Ideas?

    Finally got tired of waiting on HP.  Expected response Bob during the 'days of Forum' or whatever they called.  My problems with their goods should not have affected them too!

    FYI, I ordered a new printhead magenta/yellow, installed and still had "replace print head faulty warning."  Has released the new printhead, cleaned of some sort of clear, gelatinous * beep * of gold contacts with a q - Tip and reinstalled.  Surprisingly, printer started working.  (Took a lot of time to do her routine 'thump, bump & hum'.)  Don't know how long it will last.

    My next printer will be a Canon or an Epson!

  • DesignJet 1050c more: 1050c print head cleaning

    Hi all

    I recently bought a 1050c more printer in fairly decent condition. I used to use a Roland SP540v at the office but this 1050c was home so I'm somewhat familiar with printers large format.

    His print beautifully after I replaced the timing belt, new valves of printhead on the ramasseherbe Assembly and removed all the air from the system. The only thing I noticed when I got all the covers off the coast has been the print head cleaning.

    The cleaners C, M and received this pleated filter sitting at the window near the wipers but the black does not. Is this normal? I can see what appears to be a sponge sitting at the front of the vacuum cleaner that I don't see in color.

    Refurbishable are printhead cleaning products? I only ask because it will be a unit of the House and I would try save as much as I can where I can.

    Kind regards

    Select this option.

    I just went down and checked on my 1050C cleaners and Yes, they are the same.  Also the same on the cleaners of the 5000 series, IIRC.  Foam on all colors but black without foam.

    Can you tell me where you extracted the floodgates of print head?  Also, I have a problem with the air in the lines on my 1050c and seeks to replace the system of whole tube by a refurbished.  But if I can try to solve it by simply replacing print head valves, I could even quite a bit of money.

    Thank you!

  • my print head large format 7500 needs?

    My 7500 has large format officejet displays the message "ink cartridge seems to be missing or damaged.  I cleaned second level clean print heads, put in a new hp black cartridge, clean the plates of copper brass on the cartridge and the printer.  do I have to replace the print head?

    I understand that you are looking to replace the print head after doing the different troubleshooting steps, but I would like to clean the print head manual too. Here a link to the user manual. It will show how to clean the print head and what materials to use on pages 120-125. While you clean the contacts on the print head after you delete it, check to see what warranty end date to the printhead is. If this date has not passed, I would call into HP total care for quality output troubleshooting.

    I would also do a hard reset of the machine to try to clear the error message and return the printer to a known working state. No user settings are lost with a hard reset.

    1. with the printer plugged directly into a wall outlet and turned on, unplug the power cord from the back of the printer.
    2 then unplug the power cord from the wall outlet.
    3. wait at least 30-60 seconds
    4. plug the power cord into the wall outlet first. If a module with the power cord, make sure that the light of the module and then reconnect power cord on the back of the printer
    5. the printer should power back on by itself, but if not use the power button on front panel to turn on machine.

  • OfficeJet 6500 Series E709A: aligning the print heads whenever the printer on

    Replaced print head cartridge-door and put new cartridges.  Now, every time I power the printer, he gets head alignment mode and print a correct page.  I press the OK button and the printer works correctly then.  It is the second replacement in two years.  Had no problems the first time.

    Don't know where you answer correctly on this problem that I reported.

    After trying all the options that have been proposed and did not get a resolution of the problem.

    I tried the only other possibility was not offered.  I bought another head of HP ink replacement

    which is where I had bought that does not.

    The new replacement of HP has solved my problem.  The printer works properly.

    I guess I get out of $70.00 for non-functional replacement, unless someone wishes to

    give me a contact who does not send back them on where

  • I have the print head and the alignment of the problems with our officejetpro8500 910 a.

    We noticed that the cyan ink was not printing. The product is out of warranty about five weeks before we noticed a problem. We have replaced all the ink with the new hp ink cartridges. We have tried printhead cleaning several times until the third level cleaning when cleaning the print head has failed. We tried to align the printheads without success. We have been dealing with this during more than a month now. We have only 440 pages printed during our first page of self-test diagnostics. Our print head shows that it is under warranty until April 4,2012. We consulted a repair center. We have exausted all the other options until the replacement printhead. We changed to print in black only. Now, she wants to print a test page everytime we try to print something. Ink, we bought at costco for this printer was a third of the price of a new model of 8600. Please help before my wife beat me with this printer!

    If the printhead says it expires April 3, 2013, so the date of warranty.  You should be able to get a replacement print head by contacting technical support of HP and good news, it should be free, since the part is under warranty.  You can join the 1-800-474-6836 technical support to the United States and the Canada International users click here.  Let me know what happens.

  • HP Officejet 6600 print head error message

    Recently had an electrical storm and power neighbor hood was off briefly. Though even my printer is plugged into a surge protecter, I now have an error message on my printer that reads...

    "Missing or faulty print head".

    ceyan, magenta, yellow, black

    the print head seems to be mjssing, not detected, incorrectly installed, or incompatible"

    Before the storm, I had installed 2 new ink cartridges. My troubleshooting efforts consisted of unplug the printer from the power source and plug back and removing ink cartridges / resettlement. I always get the error message "printhead".

    Hello

    I think you did everything I would have tried.

    Even if unplug you the printer, I wonder did you leave it unplugged for more than 15 seconds.  See the link

    http://support.HP.com/us-en/document/c03750651

    If this does not resolve the problem then I think it would be appropriate contact HP because this printer is probably still under warranty.

    Hope this helps somehow.

  • printers HP 8500 (A910a): print head for white stripes of printing cyan horizonnally

    HP 8500 (A910a).  No. Windows7, no change in system error message. The system is hp Pavailion Elite m9150f

    Prinrt instakked wired Ethernet networking

    Printhead print white strips horizontally on cyan and green on Test patter diagnosis 2.

    Checked the blanck/cycan printhead. Cycan nozzles are dirty.

    Can I clean (how?) or do I replace the print heads? If so, replace a print head, or both?

    After the old replaced print head, printer replrts the cyan cartridge is low. It's a brand new cyan cartridge. How can I get the printer to consider new?

    To answer the first part of your question, you can clean the heads printing either through the front of the printer or do a manual cleaning.  This document here will focus on horizontal lines in printing and show how to correct the issue, clean the print head through the façade and based on the printed report, the print heads to replace.  The other way to clean the printhead contacts is to do a cleaning of the contacts of manual.  Here a link to a document that shows a way to clean the contacts manually.

    The cartridge error message, I would like to look at this document. He will wear the error message you are getting and troubleshooting steps of the offer to take to try to solve this problem.

  • Print head on V715w

    Printing perfect color but not black.

    So I went through the black cleaning and process print head worked but has no color!

    I did it again and now colors work but black does not work!

    I use a paper filter coffee - as suggested by Dell - or J cloth

    Advice please?

    Ian

    Ian,

    Try to read...

    The printer does not recognize the cartridge ink, or only in one colour prints

    Also, try to go in the printer preferences and make sure the box is checked to use all of the available ink.

    Rick

  • DesignJet 5500: print head print test very good page, but I still get the error message to replace the printhead

    On my DesignJet 5500, I rswitched the ink tubes, printheads and printhead cleaners dyeing anti-UV, 81 to 83.

    I got an error message saying that the black print head needed to be replaced so I bought another head black printing and after that, I was able to print a test page that shows all the colors (image quality page?).

    Magenta not give not any code of error before, but now I get an error message saying that the printhead magenta must be replaced, even if magenta print well on the printed test page.

    Hello

    The printer give you a warning when the health of the print head is low, but it will continue to print.

    If the problem has been solved after all print head replacement can be that a print head cause others to fail

    Or, just a few bad print heads

  • Re: HP 6500 has more print head always needs replaced

    I own a HP 6500 e709n and have had problems with the cartridges of printers are not recognized and experiences one now where worked my 920 dual black cartridge and the printer being functional black print only with no error messages but not color print as one or more of the cartridges were probably low or dried up. I changed the cartridges out with genuine hp 920 s and now get a message indicating one or more cartridges missing or damaged-cyan. Put my old cartiges backwards and got the same failure where none were before with them. From cartridge games and open holes with PIN as described for if ensure that ventilation was allowed both sets and retried. Was always the same message on cyan then pulled the print head and cleaned by the procedure several times hp. Now get the ink system failure. Cleaned again now return to the failure of the cyan cartridge. Loop d zero. Seems that this printer know when I really need and fails at that time in a way that I can't fix.

    I worked in the manufacturing sector and in my case all returns have been watched and analized by Tech as a measure of the quality control or quality assurance. It makes sense for business profitability so much customer satisfaction. In my view, because there is a common problem that seems to be frequent, there is an exact question that was observed by the company (HP) and they know what the problem is. IM surprised that information has not been put forward here by people who represent so called HP. What is the main problem that change a print head - relieves most of the time? Dried up ink in the corridors. Hard Electronics failure of the members of the Ribbon or pc? Faulty detection mechanism? Mechanism of cartridge HP cartridge original problem to prove ID? Customers using non hp cartridge or refill the cartridge authentic? ... what causes?

    Thanks for the reply. As I said in my post 2cnd problem was completely healed of many print CRC head baths and a toothbrush. Is there a reason why it has been edited my first post on the thread? Apparently you still like you he referenced earlier. Thanks, Keith

  • replace the print head, always print the habit or alignment. OfficeJet 6500 has more E710N

    cleaned print head, installed new print head, always feeling used or align.

    Hello @tgrtlr , welcome to the forums there.

    I understand your Officejet 6500 a is not by aligning, or print for you and I have a suggestion to use your troubleshooting steps.

    Check out this guide and try the steps: "Alignment failed" Message appears on the printer control panel

    If these steps do not help, and the alignment is still not completed successfully and you cannot print, you can also try these steps by Bob_Headrick: black ink does not

    If you want to follow through with instructions to Bob, I would recommend only read and carefully.

    If all else fails, I would finally call HP to see what your replacement or options trade can be.

    Details of HP:
    If you call in North America, the number is 1-800-474-6836 and if you call outside the United States / Canada: click here.

    All the best! Have a great Monday!

  • My PIXMA MG5320 has error U052-' the type of print head is incorrect. Install the correct print head

    My printer has stopped between different documents with the printing error U052.  He has said, "the type of print head is incorrect.  Install the correct print head. "I couldn't find help on the support page.  A YouTube video showed me how to get out of the print head and clean it manually.  I did this and reinstalled my ink cartridges.  I still have the error.  I can't align my printhead.  Buy a new print head or I have to buy a new printer?  I love this printer!  He is a year old.

    Hi Brooks14,

    If your printer was purchased less than a year, we will be able to replace it under warranty without having to buy a new.  Since you've already tried it replace unsuccessfully, I recommend to use the link contact us to contact our support staff that can go through your warranty options

  • Designjet Z5200: How to replace a print head on Designjet Z5200

    I have updated firmware and ran troubleshooting and received the message of

    replace the printhead for LM - LC.

    It's a part that I can order and replace myself or is it recommended to fix my printer?

    My warranty has expired.

    Thanks for your suggestions, help about this.

    Hello

    You don't need a technician to replace a print head.

    Here are the instructions to replace the printheads

    http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c00810189

    Best regards

    Mike G

  • print head problem Officejet 8500 has

    Hello

    I just replaced all my ink cartridges, and still it tells me that there is a printhead problem; the message says to replace the printhead to resume printing.

    Didn't I do it when I changed the ink cartridges?  Visual instructions on the printer seems to show a slightly different model of what I, and the print head seems to be separate.  It does not have to be the case in my model.  Anyway, the instructions also say press the button 'change print head' in the main menu, I can not even to the main menu but it is stuck on the message "print head problem".

    I'd appreciate some advice on how to proceed!

    Thanks in advance!

    This picture help?

Maybe you are looking for

  • The screen does not. Apps not opening.

    Hello I recently bought an iphone 64 GB (2 weeks ago) running IOS 9.3.1 6s. It seems that my phones screen sometimes does not respond (except form slide it down or screen) I tap to open applications, and nothing happens, you can check the vid I poste

  • Is my Stor.E what USB HDD warranty alu2?

    Hello all,. I was wondering if anyone can confirm if my USB hard drive external StorE Alu2 has of a warranty period? I've had for a little over a month and it stopped working. She was abandoned once, not very well and has a small dent on the top, thi

  • Positions the cursor can not extract the subset of waveform

    Hello I try to get two positions the cursor on a graph of waveform for the entries for the code below, which will start a process that will analyze a subset of the wave. The two sliders define the start and endpoint for the waveform (cursor 0 is the

  • multi meter PCI-6602 daqmx semi period measurement

    Hi all, currently I am working on 20 channels PWM. I have a problem on my labview code. Would anyone give some advice on my vi? I packed for 2 channels labview code, for now. I do measure period semi. I want to measure the cycle frequency and the dut

  • Region of licensing Windows are specific?

    original title: regions In the name of God I want to know if you buy a windows area of cant you active in another region? for example if you buy windows in the Middle East, can you active in other regions such as Asia or europe? with special thanks