Replaced the G550 motherboard. Won't boot black screen and high.

Similar Questions

• C355 all-in-One won't boot black screen

  Hi all

  I have a C355 all-in-one who had a serious problem lately. When I try to turn on the pc with the power button, it makes the whirring sound, but the screen is black and it won't turn. The power button stays on and sounds like it starts up but the screen remains black and does not turn.

  I tried unplugging all USBs thinking it could be the conflict with the other drivers, but it does not work. It usually takes 20 + attempts after pressing the power button on and off with no screen until the PC actually turns. It is extremely frustrating, sometimes over an hour before I can get the computer on! I made sure that all drivers are up-to-date, and 8.1 windows is fully updated. I don't know what else to do to try to solve this problem. This PC is not under warranty but its still relatively new. I wouldn't have to spend money on another computer for this reason. If anyone has had this problem or have any suggestions to try to fix? Thank you.

  I ended up taking the all-in-one to a repairman. The cpu has been damaged from overheating. They said it was a common problem with all-in-one which have an amd cpu and warned me to stick in the future equipped with Intel processors. The cost of the repair was too expensive for my cheap all-in-one so I got the hard drive recovered and let it go!

• S10 - 2 won't boot, black screen

  Don't know not what has happened, one day it worked fine the next day, I pushed the power button and I could hear the hard drive turn into action, all of the lights (power, battery and wireless communication) all lights up and the hard disk light flashes as usual, then I hear the hard drive to stop. While all this takes place (about 5 seconds), the screen stays black and never comes.

  I can't use the F keys to try to get to the bios Setup and I see no windows start because the screen is black.

  Can someone tell me what to do?

  
  

• Ive got windows xp... When I turn it on it starts windows loading ok.the icon rises then atfer a black screen and a message saying that the application has no enterliszed properely.then click ok to complete the applications.still does not

  applications has not enterlislze properely.click on ok to finish the applications.i done this but still don't work

  Hi Tracey341975,

  Your computer will load at all? If operations so the following, listed in the link below. If it does not start, please in safe mode by pressing F8 black of the screen before the windows logo and select Safe mode and perform the following, listed steps in the link below.

  http://support.Microsoft.com/kb/310353

  Let us know if your computer has no errors in case of boot. If it is not it means that you have an application that is causing this error, we can identify and solve.

  I hope this helps!
  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• At the start of the laptop goes to a black screen and says invalid partition.

  Original title: can I PRO 1-2cpu (IBM Laptop) Xp.

  • Not long I Formated my Windows XP PRO 1-2cpu, thinking that he would have run faster, not a blue screen crash and eliminate any viruses that could in fact, now that its formatted I can't use, whenever I start the laptop it goes to a black screen and says invalid partition, I don't know what that means though.

    so my question is there a way I can restore the computer back to normal? However, I don't have a recovery disk.

  A lot depends on how reformat you your hard drive.  Most manufacturers have a recovery partition on the hard drive that can be used to reinstall the operating system. Access you this by pressing a button that appears briefly at the beginning of the boot process.  If you have reformatted the drive c: partition only you might be OK and can get by using this recovery partition.  Otherwise, if you reformatted all the hard drive, then your only alternative is to get a Windows installation CD, boot from this CD and reinstall Windows.   Contact your computer manufacturer for advice.

  HTH,
  JW

• Computer will not start with Windows. I get a black screen and a blinking cursor.

  Windows XP Home Edition startup problem

  I have Windows XP Home Edition, but the computer does not start at the top.  I get a black screen and a blinking cursor.  I have an XP installation disc.  I was in the Recovery Console to recover all of the standard tasks, but nothing helped.

  Brand, model and model number of your PC?

  Are you able to get into the BIOS?
  What took place prior to this problem?
  For now, you can read this to get some ideas:
  http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm

• Satellite L300 has only a black screen and will not load.

  Mobile hit child around keys shortcut if, Esc, cap locks, fn etc loading upward on the web, top computer laptop has black screen and then tried to load up.
  See screen for a moment and then is become black and now the laptop starts but the screen is black and nothing else happens.

  Can someone help

  Thank you
  Tony.

  Hello

  You mean that you are not able to access the BIOS?
  Have you tried to use the FN + F5 key combination to switch to view different devices? Select this check box. Maybe the output display has been switched to external monitor?  :|

  If nothing will not help to remove the battery and disconnect the portable AC.
  Wait for about 1 hour then reconnect both sides and try to turn on the laptop.

• Component button Power on the motherboard has broken and I was wondering if I had to replace the whole motherboard or just that one piece

  Aspire v5-122p-0408. The component on the motherboard power button broke and I was wondering if I had to replace the whole motherboard or just that one piece

  Hello

  For more information about this, please contact Acer Support, ask in the Support Forums or ask your local Computer Repair Tech.

  http://community.Acer.com/T5/discussion-forums/CT-p/boards

  See you soon.

• Invalid product key, left my computer with a black screen and a cursor of the mouse on the boot.

  A few days ago, I tried to upgrade Windows 7 Home Premium (64 bit) to Windows 10 using the free update. Installation hung at 84% for 2 hours, then restarted, was unable to recover the installation and then could not get back to Win 7. This left us with a black screen and a cursor of the mouse on the boot. The computer would remain in this State for about 10 minutes and then reboot and repeat.

  Fortunately, or so I thought, I had a few CD Windows installation backup from the back to the era of digital river. So I thought I'd install fresh on my empty partition, copy my files and data, and then format the partition with the installation broken on.

  I did, but now he tells me that my product key is not valid and cannot be activated. The product key came on a real label on the PC when we bought it.

  The key is for X 16-96072. I installed X 17-58997 (Windows 7 Home Premium x 64 with SP1 (u)). I don't know what is the problem with the key? Should I have installed without the (u)?

  One key 25 digits grouped in 5 sequences of 5 characters not X 17-58997.

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the diagnostic report produced by the MGADiag tool (download and save to the desktop -http://go.microsoft.com/fwlink/?linkid=52012 )
  Once downloaded, run the tool.
  Click on the button continue, after a short time, continue button will change to a copy button.
  Click the copy button in the tool (ignore the error at this stage) and then paste (with r-click and paste or Ctrl + V) in your message.

• Satellite L775D-10W - stucks Boot: black screen + mouse cursor visible

  Dear supporters,

  Model: Satellite L775D-10W
  Operating system: Win7 64 bit
  Problem: The procedure start STRP stuck after "Windows load data" and a progress undertitled with 'Microsoft Corporation' bar, resulting a black screen and a mobile mouse cursor.

  The same problem occurs every time...
  pressing F8 > options (safe vaissaille mode) > start gets stuck
  Boot from DVD of Win7 64 bit > startup gets stuck
  Boot from DVD of Win7 64 bit > options > start gets stuck

  It is likely that the graphics card is broken or that the driver no longer appropriate?

  Thank you for your time in advance!

  Greetings

  Carpet

  Graphics card problem may be possible but in this case the POST (power on self test) would not be passed, and in my opinion, it is not possible to access the BIOS.

  However, it's just a theory
  Try to start Notepad using some Live CD like Linux

  I would also recommend to start the advanced boot menu. (by pressing F8) and choose repair my computer option.
  Then select Toshiba HDD recovery

  This option would be to recover the laptop back to factory settings.

• Mac Pro black screen and the cursor on startup

  My Mac Pro won't start. He begins the start but stalls on a black screen.  None of the fixes recommended work (I tried them all THE). As I finally understood, it's el Capitan does not like more than one monitor (I have three). When I unplug the two monitors, it starts fine. Yosemite has worked well with three screens, ElCapitan started very well that if I unplugged one of you watching her. The latest version requires me to unplug both monitors so that it can start up.

  What specific Mac Pro?

  What specific graphics cards are installed?

  Are these Mac-Flash cards? They need additional drivers?

  How the monitors are connected?

• T420s black screen and no boot

  Hello everyone,
  I hope someone could help me with this problem
  I have a T420s that I bought a few weeks earlier, it's a used, so there is no guarantee with it, I used it several days without any problem, I do not use very often I use my business an alone most of the time.
  One day when I tried to turn it on, it stacks on a black screen and it beeps a beep then two other, nothing show on the same screen not the logo of thinkpad at the start, I thought it was a RAM issue about so I put my PC business, but without a bit of luck, so I wanted to see if his graphics controller issue I plug the VGA on laptop and my TV cable, and here I see boot thinkpad logo but after that I see a message on the screen saying: "real time clock error - control of Date and time settings." Press ESC to continue or F1 to enter setup"and when I press either nothing happen at all, always there batteries.
  I'm lost here, can anyone help please.
  Sorry for my bad English.

  It is used, it does not mean that there are no guarantees. If it is sold, the warranty stays with the machine. Check here first:
  http://support.Lenovo.com/en_US/product-service/warranty-status/default.page?

• When I was playing the game and my 3D PC show the black screen and the sound of noise.

  Hi Admin,
  When I was playing the game and my 3D PC show the black screen and the sound of noise. And then I can't move anything and I can restart only. What is this problem? I don't know why? Please help me what should I do.
  My PC specs are as follows

  Aspire M5800 (Q84MR375) Genuine Windows Vista® Home Premium, 64-bit, Intel Core 2 Quad processor Q8400 (2.66 GHz, 4 MB L2 Cache, bus front at 1333 MHz), 3 GB Ram, 750 GB S - ATA HDD, DVD SuperMulti Double Layer drive, Nvidia GeForce GT220 graphics (1 GB dedicated RAM) card, Wireless LAN, keyboard and wireless mouse with LCD 23 '' monitor.

  phoechan,
  More than likely if this started after you upgrade to Windows7 then you might have to update your hardware drivers.  Go to the websites of the manufacturers of hardware for your PC and get all the latest drivers for Windows 7 (video, sound, chipset, etc...).  If they don't have Windows 7 drivers you may have questions until they create them.  You can also try to boot your PC and also right click on the game .exe file and change the compatibility mode to Vista or XP.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Black screen and mode standby with the message "no signal".

  Correctly, it's... kind of weird, I use my computer and the monitor for a year or 2 now and don't never had real problems. The thing is that when I got home last night I found my black screen and standby mode (as if the computer was turned off (which it wasn't)). I thought that the reset will solve the problem, and so I did and didn't get the message "no signal". All tried, reconnecting cables, reset several times I could count... nothing helped for awhile.

  At any given time during one of my restarts it reworked all of a sudden no aparent reason. So going on my daily buissiness I want to get back in the saddle, when I accidentally hit the side of my computer with a book and the screen went to 'no signal' again. Just tried again and even used my cell phone to check if the monitor was working,... now comes the weird part,... also on my laptor monitor is having problems with "no signal", but only when I do my main screen. It works as a secondary screen, but I can't get the context in which to work. (finding that I'm guessing that this problem is not related to my normal computer, but I'm not sure).

  I am running vista and got a nvidia 8800GT graphics card. Also, I noticed something that is at any time using both the hdmi cable on the graphics card or using the socket with the internal chipset of my computer makes no difference. in both cases, I get "no signal" and the screen goes to sleep... Is there someone who can help me and tell me what probably is the problem here? I'm really looking forward to the answers, thank you very much for your time and effort.

  Hi Ron Suykerbuyk,

  If you are comfortable, then try to remove the CPU cover and check if the graphics card is well connected to the motherboard. Even if it is connected correctly, you can try to reconnect the graphics card and check.

  Hope this information is useful.

• Start the computer to black screen and the computer runs hot

  original title: sick Vista laptop

  My daughter portable computer began acting strangely very yesterday.

  Once connected, I get a black screen and a cursor.  The system seems to work at full speed, because I can hear the fan, and it runs very hot.  No matter how long it sits, the desktop does not appear.

  I can use Ctrl-alt-del to display the Task Manager.  The list of processes is limited to the process of the current user, and none of them use important CPU. If I click on 'See the process for all users', taskmanager freezes and I have to disconnect to get rid of him.

  Using the Task Manager, I can kill the process Explorer and then start it again, date at which I get my desktop.  However, it is still running hot and noisy.  With the help of SysInternals ProcessExplorer, there is no process using any important CPU.  Most of the time CPU is reported as inactive.

  I don't know what to think.  A boot loader took over the system?  A hardware problem?  OS corrupted files?

   

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner