Replaced the motherboard and the HARD disk and now you try to transfer the old TB on the new, but cannot locate the files on the HARD old disk which is now the drive 'E '.

Similar Questions

• I replaced my motherboard and now my pc won't start

  I have successfully built many PCs.  Now, I'm stumped.  I installed everything correctly (as I did many times before), but this time I can't boot the OS cd.  It is all ready to go.  I checked evreything.  I turn on... and nothing.  I have check everything new (I did this several times) I hit a brick wall.   I can usually understand these things, but this time I can't.  Any help will be greatly appreciated. Is my addy * address email is removed from the privacy *.  Thank you very much.

  If it starts after the POST screen to start loading Windows? If this is not the case, this is definitely a hardware problem and not a software problem. You'd probably find better help in a forum dedicated to the material (Anandtech, HardForum, etc.).

  You could try to clear your CMOS and see if that helps. Otherwise, start with the bare minimum of RAM, video card and no other add on cards. See if that helps.

• Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Migration of CS4 breaks the license. That's what 150:30 means. Assuming you are using a Mac.

  You can use the Terminal method to repair the license... but I stress that carefully read you and understand the instructions here before you run it. beginning

  # 11. https://forums.Adobe.com/thread/1714695

  If this isn't what you want to do, you have to reinstall.

  Gene

• When you try to transfer a file of 8 GB on external hard drive 'file too large for the destination system message' to get there is that much space on disk

  When you try to transfer a file of 8 GB on external hard drive 'file too large for the destination system message' to get there is that much space on disk

  Hello

  Discs formatted with the FAT be limited to files with a maximum of 4 GB. You can format outside
  drive drive with NTFS, contact the manufacturer if necessary pilot or split the file into parts under
  at 4 GB.

  Overview of FAT, HPFS, and NTFS file systems
  http://support.Microsoft.com/kb/100108

  How to go beyond the limit of 4 GB on FAT32
  http://lazybit.com/index.php/2007/03/01/how_to_get_over_the_4gb_limit_fat32

  -------------------------------------------------------------------------------------------------------------------------

  The ZIP file and then divided the ZIP which helps maintain the integrity of sharing files and restoring.

  Zip and Split - free
  http://zipandsplit.toolazy.me.UK/

  Split and Zip - free
  http://www.jtoolgame.com/tools/splitzip.html

  Akhir Split Zip - free
  http://www.mydigitallife.info/2009/04/24/Akhir-split-zip-splits-files-into-smaller-zip-files/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• How can I find my username and password for Windows xp media center? don't remember setting but cannot get back in after the restart.

  How can I find my username and password for Windows xp media center? don't remember setting but cannot get back in after the restart.

  Hi Carol_971,

  1. Did you the latest changes on the computer?
  2. You have security software installed on the computer?

  Method 1

  I suggest that you try to start in safe mode and then try to log on to Windows using the default Administrator account and then remove the password for your account, check if it helps.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Method 2

  If you are unable to log on to Windows in safe mode, refer to the article below and then try the steps mentioned, check if it helps.

  How to connect to your Windows XP-based computer if you forget your password or if your password expires

  http://support.Microsoft.com/kb/321305

• 1001 error code in the registry when you try to remove an old program using programs and features in Control Panel. How can I fix?

  1001 error code in the registry when you try to remove an old program using programs and features in Control Panel.  How can I fix?

  Computer Windows 7

  Tried to reinstall the older version, she received error 1001 something again with the registry.   Does not remove old software.

  Hi Carol,

  1. what program or software you are trying to delete?

  2. What is the code or an exact error message?

  Please provide us with more information on the specific question, to find a solution as soon as possible.

  Follow the link below and check them with the question:

  Solve problems with programs that cannot be installed or uninstalled:

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

   

  I hope this helps.

• I have just replaced my computer and now need to reinstall Dreamweaver. I can't for the life of me find anywhere on the Adobe site to download again. Should what steps I take to download and reinstall the software I pay for every month?

  I have just replaced my computer and now need to reinstall Dreamweaver. I can't for the life of me find anywhere on the Adobe site to download again. Should what steps I take to download and reinstall the software I pay for every month?

  Download/install the desktop application, connect and install applications subscription.

  Creative cloud to desktop
  https://helpx.Adobe.com/creative-cloud/help/creative-cloud-desktop.html

  Sign out, sign in | Creative office cloud app
  http://helpx.Adobe.com/creative-cloud/KB/sign-in-out-creative-cloud-desktop-app.html

  Help of activation & deactivation
  https://helpx.Adobe.com/x-productkb/policy-pricing/activation-deactivation-products.html#a ctivate-how-to's

  Install, update, or uninstall applications
  http://helpx.Adobe.com/creative-cloud/help/install-apps.html

  Install creative Cloud applications
  http://TV.Adobe.com/watch/CS6-creative-cloud-feature-tour-for-video/installing-desktop-app s-of-creative-cloud.

• I built a computer and just replaced my motherboard and CPU and now I am asked to buy a new product key for Windows Vista.

  I built my computer 4 years ago, I just rebuilt by replacing the motherboard and processor and now after starting my PC that I am invited to buy a new product key, one I had when I bought windows is already associated with another installation, Yes this installation, it is always on the same hard drive just a new motherboard and processor

  original title: why I have to buy a new product key

  1) click on the Start button

  2) type: slui.exe 4 and press the Enter key

  3) select your location from the menu drop-down and click on the next button

  4) the next screen provides the number to call to Activate by phone

• I read the excellent instructions, but cannot locate the green arrow to start the download! I did not accidentally remove the arrow, because he was never

  I went on the Mozilla site to download to my Mac. I read the excellent instructions, but cannot locate the green arrow to start the download! I did not remove accidentally the arrow, as it was never there to be seen. I use Safari and don't have Firefox on my MAC (to my knowledge).

  Thank you

  PS: I clicked on the 'automatically add' and downloaded the file, but when I tried to open it, I get the message "Safari cannot read this file. Cool, huh?

  See how to install Firefox on Mac.

  • https://support.Mozilla.org/KB/installing+Firefox+on+Mac
  • http://KB.mozillazine.org/Installing_Firefox#Mac_os_x

  Open the Firefox disk image file and drag the Firefox program into the Applications folder on your hard drive.
  Do not double-click the Firefox to run from the disk image, but instead, drag it out of the DMG file.

• PAGE_FAULT_IN_NONPAGED_AREA___Msg DISK_0? Block 8: can? t read, replace the drive or remove the writing (Dell Dignostic softare scan) _ Protection

  I had purchase Dell inpiron 910 mini two years before now out of warranty. I got error on blue screen and then I restart the machine, I got the mode without failure when starting in safe mode, it stops and a disk read error occurred press Ctr + alt + del to restart I could even not to format the machine. could not start for winodow cd. Same blue screen message when starting from the cd, the message is as below
  A problem has been detected and windows has shut down to prevent damage to your computer.

  The problem seems to be caused by the following file: partmgr.sys

  PAGE_FAULT_IN_NONPAGED_AREA

  If this is the first time you've seen this stop error screen,

  Restart your computer. If this screen appears again. follow these steps:

  check to make sure any new hardware or software is installed correctly.

  If it is a new installation. Ask the manufacturer of your hardware or software for any windows update you might need.

  If the problem persists. disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shading if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options. then select Safe mode.

  Technical information:

  STOP: 0 X 00000050 (0XF7895726, 0X00000000, 0X00000000)

  Partmgr.sys - address F7895726 base at F7893000, DateStamp 00000000

  I ran the Dell cd dignostic is to show the following error message:
  Error Code 0F00:1344

  MSG DISK_0? Block 8: can? t read, replace the drive or remove the write protect

  The given error code and message can use Dell Technical Support to help diagnose the problem.

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest to unplug external devices such as printer, scanner, etc. that are plugged into the system, and then restart the system and check if the problem persists.

  Error code 0F00:1344 you listed are hard drive error codes. Usually, this means that the hard drive needs to be replaced. I suggest you to contact Dell support for assistance. Once the hard disk is fixed, you can try the methods mentioned below.

  Click on the link below, contact Dell technical support.

  http://en.community.Dell.com/support-forums/disk-drives/default.aspx

  Method 1:

  I suggest you to do a check disk from the recovery console and check if the problem is resolved. Follow the steps mentioned below.

  a. start into the recovery console using the XP CD. Follow the steps mentioned in the article below.

  Description of the Windows XP Recovery Console for advanced users

  http://support.Microsoft.com/kb/314058

  b. perform a disk check.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Method 2:

  I suggest you to start with the XP CD and then do a system restore. Follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• I changed my motherboard and now I "did not have a genuine windows edition" - help?

  It is about the title - changed my motherboard and now my edition is 'invalid' - to add spice to the bad luck, this is the second time I have reinstall on a new Board of Directors, so ofc, my second key does not work either - is there a way to legitimize my old keys? be I'll shoot 'em and send 'em you wise email (as long as I have enough access to do it in my unregistered version of the software, to do), but in short - I got two keys to have payied a sizable amouont of money for so please fix this

  Kind regards

  Simon

  Hey Mister Paton (SIR! = o)-ty for help, seems the problem is now resolved, much appreciated and good luck

  Simon

• I get an unknown error message when you try to copy a cassette of my video camera, but the camera connect

  I get an unknown error message when you try to copy a cassette of my video camera, but the camera connect

  If you are running Windows XP... There is a slight chance
  that by running the following command would be the fix:

  Reach... Start / run... and type or copy / paste the following text:

  regsvr32 %windir%\system32\qdv.dll

  Then... Press on... Come in...

  You should see a dialog box stating:

  DllRegisterServer in C:\WINDOWS\system32\qdv.dll successful

  Good luck...

  There is debate on this subject in the following forum:

  Windows Movie Makers Forums
  An unknown error has occurred

• How can I create a list of contacts on Outlook Express. I found the answer in help, but cannot locate elements, on what he asked me to click

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:
  How can I create a group or a list of contacts on Outlook Express.  I found the answer in help, but cannot locate elements, on what he asked me to click

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  If you're running Vista, you have Windows Mail, not Outlook Express. These instructions for adjustment of these two programs.

  To create a group of contacts:

  You can create a single group name (or alias) to use when sending a message to several contacts at the same time. Just create a group name and add individual contacts to the group. Then just type the name of the group in the box for when you send mail.

  1. in the address book, select the folder in which you want to create a group. Click New in the toolbar, and then click New Group.
  2. the Properties dialog box opens. In the group name box, type the name of the group.
  3. There are several ways to add people to the Group:
  a. to add a person from your address book list, click Select members, and then click a name in the address book list.
  (b) to add a person directly to the group without adding the name to your address book, type the person's name and e-mail address at the bottom of the Properties dialog box and then click Add.
  to add a person to both the Group and your address book, click New Contact and enter the appropriate information.
  (d) to use a directory service, click Select members, and then click search. Select a directory service in the drop-down list at the end of the text box. After finding and selecting an address, it is automatically added to your address book.
  4. Repeat for each addition until your group is defined.

  Note

  a. to view a list of your groups separately from the list of address book in the address book on the view menu, make sure that folders and groups is selected.
   
  b. you can create multiple groups, and contacts can belong to several groups.

  If you want to send to a group without addresses are displayed for each recipient, open the address book and make a new entry. Enter the name of the group in the area of the display, but use your address. (Some Internet service providers require a legitimate address in the line to and recipients will know it's from the Group).

  Click on the button to. Enter the name of the group using your address. Enter the group in the BCC field.

  Bruce Hagen MS - MVP [Mail]

• Error message: "the version of this file is not compatible with the version of Windows that you are using", when you try to run an old ms - based back program in Win-7 Ultimate 64 bit.

  Original title: program compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs

  I get this message when you try to run an old MS-DOS - based program in Win-7 Ultimate 64-bit.

  "The version of this file is not compatible with the version of Windows you are using. Check your computer system information to see whether you need a x 86 (32 bit) or x 64 (64-bit) version of the program and then contact the software publisher. »

  I understand that I am under a 64 bit OS, but is it possible to get this program to run? I was wondering if anyone has tips :)

  Hi Bcopeland,

  Thanks for posting your question in the Microsoft Community.

  Based on the information, you are trying to install and use an old ms - dos program based in Windows-7 Ultimate 64-bit.

  The problem is a software that was created for Windows 95, 98, and Windows XP has no way to work correctly with an operating system that didn't even exist when the software was written. However, the error message you get normally means that you have a 32-bit software that you are trying to install on a 64-bit system.

  You can check the compatibility of the program with Windows 7, in the Compatibility Center.

  Compatibility Center

  If the program is not compatible, then you try to install and run the program in compatibility mode.

  a. click right on the program.

  b. click Properties.

  c. click on the tab compatibility.

  d. Select run this program in compatibility mode and select Windows Vista or whatever to use the system, the program was executed successfully.

  Here is an article that gives you more information on this:

  Make older programs in this version of Windows

  If the problem persists, you can get in touch with the software vendor to see for the latest version of the program to use the same system of 64-bit Windows 7.

  Hope the helps of information.

  If you need assistance in the future to resolve any issues related to Windows, post your query and we will be happy to help you.

• I have Acrobat 8 Standard on my computer, but cannot locate the CD of Acrobat 9 Pro that I bought. I can't download on this computer.

  I have Acrobat 8 Standard on this computer. I bought an upgrade to Acrobat 9 Pro, but cannot locate the disc not am I saw a bit of luck downloading the software. Any suggestions?

  Available downloadable Setup files:

  • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | Suite X | 9,8 | 9 standard | 8 standard
  • Captivate: 8 | 7 | 6 | 5.5, 5 | 1
  • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2
  • Lightroom: 6| 5.7.1| 5 | 4 | 3
  • Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
  • Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".