replacement of the plug power supply without serial adapter?

Similar Questions

• HP Pavilion p6-2: problems on blocking down after I installed the new power supply on a p6-2207ep

  Hi all

  B4 explaining my problem, I really don't know if I should post this in office, or material in this section of the freezes/crashes/locks but since I posted in freezing section and no results I decided to try here.

  My pc: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03382032

  I bought a new PSU: XFX TS 550W 80PLUS BRONZE for the GPU upgrade 380 R9 I was planning to do.

  Is there some BIOS I get HP for this cause of power supply from what I read, if I not only one of the things like manufacturer reset to the factory settings may stop working... Currently, my Bios version is 7.11...

  Problems with the new power supply:

  When I closed windows 7, the first problem, the picture freezes on the screen that says "blocking windows down", I waited a bit and nothing, tried to turn off the machine while keeping down the power button but nothing to disable directly in the rear switch of the PSU...

  Second time happened a little different soomething, seconds after freezing again on the screen that says "blocking windows down" windows actually turned off and the screen is off but everything inside the computer case continues to flow fans in light of the power button / stop and was also able to close by keeping pressed power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  Also tried the GPU with the new PSU fans worked but no entry in the screen that I guess just a power supply problem.

  ATM, I'm RMA waiting to know if it is a power supply defective or not...

  Problems after the reinstallation of the original material:

  Some of the same problems when I got the new PSU remained namely:

  Windows actually stop and the screen is off, but everything inside the computer case continues to flow fans in the light of the button on / off and was also able to close by keeping the power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  What I've done so far to try to fix the problem:

  Restore windows 7 to a b4 point the hardware installation.

  Reset the BIOS

  Hard reset

  Clean boot

  Do you have a full checkdisk which means 0 KB in bad sectors...

  A complete hardware checked all tests with the HP software

  A system file check everything beautiful

  What I fear most is a faulty PSU that may have caused damage to my equipment mainly the motherboard, but could be something else entirely.

  Maybe I need a specific BIOS for that motherboard / PSU combo, but after returning to the source material, the problems remained.

  What I can do because I can only make the software tests since I don't have an extra PC to test the parts...

  Hello

  Disconnect all external devices except the keyboard and mouse when you try to solve the problem.

  Disconnect the PC and removed the CMOS battery.  Press and hold the power for 30 seconds.  Now, replace the CMOS battery and plug the PC give a TI a go.

  Your PC is not stable enough to make a BIOS update. Do not attempt to use the graphics card XFX until your PC is stable enough to make a BIOS update.

• Can power supply Question - I use the 230W power supply with a W540?

  I have a W540, which currently uses a power 170W (8.5 a 20V)

  I got also a docking station for a P50 that has a power of 230W showing 20V 11. 5a.

  The connectors are similar, but I'm hesitant to try the 230W power supply in the W540.

  It is allowed to use the 230W power supply with the W540?

  230 watts is maximum power feeding, it only provides the energy required by the computer.

  I sold my W540, so I can't test it for you. But I do use the ThinkPad X 1 carbon with 230 watts without no problem power adapter.

• Dimension 4600 doesn't work with the new power supply

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Have you used the connector 4 pins, which was part of the 20 + 4 P1 12v connector, connect to the P2 4 motherboard connector pins 12v?

  
  See 41, J5B1 Connector [aka P2]

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-4600_service%20manual_en-us.PDF

  
   http://www.AOne.co.UK/prodinfo.asp?ProductID=4523

  Connector 4 + 4 pin 12v PSU is divided into two 4-pin connectors and one of them, can be used for the P2 motherboard connector.

  Bev.

• ProBook 4530 s BIOS update fails - "...". the computer is not connected to the external power supply. »

  I made an update of the system to the original settings and everything seems to go as usual.  While performiong the many windows updates, I noticed that the battery indicator indicates "no battery installed.  I found a few solutions dealing with this problem (none of the other solutions worked) and that which is shown updating BIOS.  I checked and the BIOS is F.07 and the current version is F.41.  I downloaded the update and begun the process of Windows.  The system restarts to start the process, but when the BIOS updated starts I get the following message:

  "A significant update of the BIOS of the system is available, but the computer is not connected to the external power supply.  Please connect the external power supply and then press Enter to continue. »

  The computer is connected to the power of HP to the original address since it is the only way so he can turn it on.  I tried removing the battery and from the update only the connected power and get the same result.

  Either way, I tried to insert a different battery, I have more than one of these laptops.

  Sorry

  Please test the battery after boot press F2 HP Diagnostics

  http://support.HP.com/us-en/document/c00821429

  and calibration of the battery for laptop

  http://support.HP.com/us-en/document/c00817650

• CPU limitation with the new power supply

  Hello

  I have a W510 with 135W POWER supply. Or to be more precise: A 6.75 @ 20V.

  I work at two locations, so I bought a generic 150W PSU with an adapter to mount the Thinkpad. The PSU is labeled 7. 5A @ 20V, so there should be no problems running the laptop.

  Yet, when starting, I get the "this power supply is too low for something something something battery charge" and strangled my i7 at 1.2 GHz, and not the 3.06 there are usually.

  If I boot from the battery and connect the connector of the power supply after Windows is in place, it works at full speed. And to charge the battery very well. Then of course, there is nothing wrong with the juice from the PSU.

  Thus, I suspect that the BIOS does something stupid. Can I override this somehow?

  Friendly,.

  A guy

  Maybe what the ThinkPad does not does not correctly detect the generic adapter. The central axis of the generic adapter does not give the right signal to the laptop power management firmware.

  Check in the ThinkVantage power manager what to say under the generic adapter 150 watts? He said 90 watts?

• The 460W power supply will be sufficient for the GTX 1070?

  Just place an order for a R5 with an i7, GTX 1070 and a diet of 460W.

  I'm not going for the largest power supply, because I'm not a fan and do not upgrade components.  If the configuration of Dell said 460 page might work, I saw that he needed to upgrade the PSU. I preferred using the extra $100 for the video card rather than the 970-1070.

  Now, reading around forums, I continue to see comments that the recommended food for a GTX 1070 is 600 Watts (by guru3d.com).

  I still have time to cancel the order because it is very recent.  Do I need to worry about this power supply?  How would I know if it is not sufficient for use?  The frame rate would be low, or the stability of the system would show signs?

  Hello

  Yes, the 460W will work well if is unique. Check the image below and let me know if you need anything else:

  

• HP Pavilion Elite m9340f replacement video card and power supply

  Hello

  I bought my HP Pavilion Elite at Best Buy m9340f in 2009 and brought it to the Venezuela where I live now.

  My video card, started making the noise of the typical fan geforce 9500gs can do. The temperature of the gpu is very high (from 73 ° c without playing or watching videos!), and I'id like to replace it as soon as possible before my material fails completely.

  But the power supply 350w, to replace any video card decent needed to change my diet too. I have not the slightest idea of what type of power supply should I buy, and if I should replace the case too. My intention is to keep my cpu, my mother, my hard drive and my ram (purchase of a new system to the Venezuela is out of the question because of the barbarian prices in this country).

  Then to take the questions in order, I'll here:

  -I want another video card (geforce 9500gs is known for his failure, so I want to upgrade to a more powerful card)

  -To do this, I need another power supply, so I need recommendations on the provision of market models which CORRESPOND to my HP Pavilion Elite m9340f or

  -replace also the case: what kind of business should I need that corresponds to the motherboard of benicia

  Thanks in advance

  Jeronimo Ramos-Prince

  The information below was previously published by Big_Dave in response to several other posters about their questions about GPU upgrades. Prices shown are in U.S. dollars and for American retailers.

  Your PC has a 350 Watt PSU if below video cards will work:

  $50--->NVIDIA GT 430 9.6 Gbps - single slot width

  $65--->NVIDIA GT 520 8 Gbps - single slot width

  $80--->NVIDIA GT 440 25.6 GB/s - single slot width

  $130-->NVIDIA GT 545 43 Gbps - location single width - could be hard to find but perhaps only in the store

  $110-->NVIDIA GT 240 1 GB DDR5. 54.4 GB/s - single slot width. This card does not support DirectX 11 which is eventually used in some of the latest PC games but it's a great performer.

  Review the performance of NVIDIA specifications. Look at the specifications of strip memory bandwidth and level of DirectX support.

  I normally don't recommend video cards AMD for PC with a 350 Watt power supply as AMD provides 400 watts or more for most of its video cards.

  Frank

• How to use the external power supply on Camileo s20

  How the external power is connected to S20 and registration is possible at the same time. When the USB is plugged into my camera it will not turn on.

  1. open the battery cover
  2. remove the battery
  3 connect the usb power cable

  Now you can use S20 with external power without draining the battery.

  Crazy but true...

• Equium A200-1V0 - freezes after plug power supply AC?

  Hi all

  I'm trying to find the solution of the problem:

  My laptop Equium A200 1V0 freezes as soon as I plug the power running. I tried the new battery and new AC adapter after reading some solutions of the internet but so far without success. It works fine without the plug'in ac, but as soon as I join to food it freezes and I have to force the shutdown of the machine which is not good.

  I would be very grateful if someone can give me please the solution in detail the problem mentioned above and also let me know the cause of this disorder as well?

  Thanks for reading this thread and for your efforts.

  Kind regards

  pat3l

  Hey,.

  You use an AC/DC to original Toshiba adapter? In my view the problem must be related to AC/DC adapter or the motherboard itself

  Important is that you use Toshiba parts only to test with an AC/DC to original Toshiba adapter. If it doesn't work, it seems that the motherboard is faulty. These serious physical issues can only be set to an authorized service then you should contact the guy and ask for help. ;)

• Problems with the DC Power supply QL 355TP: I can not set the tension level

  Hello

  I'm trying to control a power supply DC via GPIB. The power supply being used is the QL355TP of society Thurlby Thandar Instruments (TTi). There are no drivers of OR to control the instruments, then I need to download and install the driver from the website of TTi: the package I installed is as follows:

  "QL - P power supplies, (including QL Series II) series pilot National instruments (Labview and CVI)"

  and I also installed the following:

  "QL - P power supplies (including QL Series II) series, IVI driver"

  So, my problem is that when I try to use the sample application of the driver 'Volts.vi DC Ouput'; defines a specific level voltage, does not work properly. The application gives no error, but it is not set the specific level voltage. However, other functions work properly, as the measure or activate the output. I tried a lot of things, but I don't know why it does not work.

  I enclose the block diagram of the application and the front panel:

  

  

  I must say that I barely control instruments using Labview and is possible that this problem would be because I did not consider things basic and mandatory.

  Any help is appreciated.

  Thank you.

  p.s. Try to replace the decimal comma to period. It is possible that the driver does not correctly handle the comma.

• Fried computer due to the bad power supply

  We did not have the computer turn on the correct voltage (it was about 120 instead of 220).

  What are the possible problems we will encounter?  Yes, the computer does NOT work.

  And what options do we solve the problem?

  It was a gaffe. I changed the switch, then my husband - lack of communication. It's a new computer desk-never used - Yes a Christmas gift for my son.

  And what is the best place to try and get a new power supply?

  Since it is a forum in the world...  The best place to get a power supply depends on where you are.

  How to determine what to...?

  Well, if this is a new machine, those you purchase contact and see if they have one, they will do out trade / sale you that will work in your machine model.  In this way, you KNOW you are getting the right feed...

  Otherwise, you will need to either take the power on (noting where everything happens so you can put a new) and take it to a shop selling things to get a replacement (large stores area, a small computer specialty store, etc.) or you will have to take the system with you and let the store that you buy to do it for you.

• How to install the new power supply?

  OK firstly plug...

  Motherboard (motherboard): N-Alvorix-RS880-formfat (Alvorix)

  PC: HP p6703w

  new power supply: GS600

  new game card: evga gtx460

  OK I am experianced abit but still novice when they treat the upgrade myself. So here's my question...

  The mobo has a slot for 24pin power cable, but the current 250w ps uses a 20 pin in this slot. Is it safe for me to use all 24 pins for the ps (GS600) I want to? What was the reason why hp has used a 20 pins on this mobo? I don't want to fry my mobo. Laughing out loud.

  Thank you.

  Welcome to the HP Forum!

  ricofico wrote:

  OK firstly plug...

  Motherboard (motherboard): N-Alvorix-RS880-formfat (Alvorix)

  PC: HP p6703w

  new power supply: GS600

  new game card: evga gtx460

  OK I am experianced abit but still novice when they treat the upgrade myself. So here's my question...

  The mobo has a slot for 24pin power cable, but the current 250w ps uses a 20 pin in this slot. Is it safe for me to use all 24 pins for the ps (GS600) I want to? What was the reason why hp has used a 20 pins on this mobo? I don't want to fry my mobo. Laughing out loud.

  Thank you.

  It is safe for you to install the connector 24 pin. You are miscounting the pins on your motherboards ATX connector. The following image is your motherboard. I count 24 pins. Product specifications for your PC State that the PSU is ATX spec.

  

  Kind regards
  ERICO

• Pavilion NC768AA #ABA: HP Pavilion model. a6719f new video card with the new power supply?

  Hello!

  So, I won money to buy (hopefully) a new video card!

  However, I have a problem.

  I don't know which one to get!

  SO, someone please, please recommend a video card for intermediate level games.

  (My budget is less than $280)

  My PC has stock everything.

  Thus, it was purchased as it was when you would get everything first he.

  Yes, I need also a new power supply that is included with my budget.

  Thank you!

  Revionion, welcome to the forum.

  I'd be happy to help you in your choice.  The main problem is, recent video cards require UEFI in the motherboard instead of a standard BIOS to legacy.  HP didn't start using UEFI until mid-October 2012.  The latest maps not requiring UEFI were the series GTX 640.  However, MSI has made a card that has a VBIOS hybrid which can operate with a BIOS.  The best thing to do is to choose a video card you like and contact Technical Support from the manufacturer to ensure that it will work on your computer as it is almost 7 years old.  This will save you problems.  They are the experts on their cards.

  I like Corsair power supply units (PSU).  I suggest at least 500W.  This will give you plenty of power for any card that works in your computer.

  If you have any other questions, let me know.  I'll be happy to help you.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Security concerns about the external power supply connected to the my map of 9401 TTL inputs

  I have an external power supply (5V DC, 500 my) that I use to test my card 9401 count entries and check my LV code is working properly. Power + 5V is used as high signal and ground as a weak signal.  I haven't done the link yet because I wanted to know if there is any concern to burn my card.

  Hello

  Normally, if everything is OK, it shouldn't be a problem.

  But in the real world "things" happen

  My Advisor is to add resistance series (in this case 1 k) to protect your device if Murphy enters the room something goes wrong.