Report Generation Toolkit and Application Builder

Similar Questions

• Report Generation Toolkit, production of the 2147417842 error, "The application called an interface that was marshalled for a different thread."

  Hello world

  I have an application that stores data in an Excel worksheet by using the report generation tool.  My VI have worked well in the past using Excel XP, but since I have upgraded to Excel 2007, I get COM errors like this:

  "2147417842 error occurred while the application called an interface that was marshalled for a different thread. in Excel_Insert_Text.vi', this is the exact wording, even with the odd punctuation and capitalization.

  The first occurrence of the error is not determined.  Sometimes, to the record 10 sessions, involving a new .xls file, may occur before this error.  Once this error occurs, I must leave LabVIEW to solve.  If I try to do something with Excel, I still get this error, even if sometimes it comes out different source Excel_Open.VI is another.

  These screw logging worked fine until upgrading to Excel 2007.  I checked and I have been using a very old version of the report generation tool, v1.0.1.  I read the documentation and had a big sigh of relief when I realized that I needed to upgrade to v1.1.2 for Excel 2007 help.  However, even after the upgrade, I still get the same errors.  I'm using LabVIEW 8.0.1 and I also build these screws in an application.   The error occurs in the application built both in the IDE of LabVIEW.  Anyone out there have any idea what I can do to fix this?  I google a bit and discovered it is a COM error, but I can't find any reference to the report generation tool specifically.

  Thank you

  Phil

  I think that suits him!

  Here's what I did: I left privileged execution environment level upper VI as "as the appellant.  I tried the "user interface" configuration, but it seemed to slow down considerably the program.

  Then, I found each sub - VI, calling the report generation tool and define the environment for running favorite "user interface".  All the errors went away, and the program is much happier now.

  Big assumption on what a Christian, thank you!

• Report Generation Toolkit compatibility with Microsoft Office 2013 and LabVIEW 2011

  Hello

  I design the 2011 Version of LabView to test solid state device and need to create test data after this unit tested.

  When I save the test data in the configuration of Excel after you run the Laview program, it created an error like "error - 41007 is is produced in NI_report.lvclass:New Report.v->... OR reports; Musr you have the LabVIEW Report Generation Toolkit for Microsoft Office installed to create this type of report. The musr toolkit also have an activated license or be in trial mode. »

  Questions: Do I need to install LabView Report Generation Toolkit for Microsoft Office on my computer? If Yes, what is the LabView Report Generation Toolkit for Microsoft Office Version. Where can I find this software?. I use Labview 2011, Windows 7, MS 2013 in the computer.

  Thank you

  Jonathan Tran

  You can try this: http://download.ni.com/evaluation/labview/ekit/other/downloader/2011RGT.exe

  From this link: http://download.ni.com/evaluation/labview/ekit/other/downloader/

• Report Generation Toolkit missing VI

  LabVIEW version 8.6.1

  Report Generation Toolkit 1.13

  I just started work on an ongoing project that others have contributed to during some time.  (This is why the project being in older versions of LabVIEW)

  On my PC, apparently miss me VI "Word get ActiveX References.vi"

  I have the version 1.13 of the installed tool, just like all other machines running this code performs.  But my word.llb only contains VI

  I tried to copy just that VI in the .llb the VI is then found by the application.  But is not executable due to this error: this VI is related to a library that does not include the VI. The VI may have been removed from the library. ' Add the VI to the library or select file "unplug library.

  I also tried to replace my C:\Program NIUninstaller Instruments\LabVIEW all 8.6\vi.lib\addons\_office\ the directory with the files from a PC that worked.  Yet once, I get the same error as above.

  I tried to do a repair on my installation of the box tool.  But as far as I know, it did nothing.

  I also tried just reinstalling the Toolbox.  But since that it has been already installed, it did nothing.  I would hesitate to uninstall and reinstall the Toolbox for fear of breaking all my 8.6 projects, as well as perhaps my 2009 projects.  I don't think that he messes with my 2009 installation.  But I know the order in which things are installed can be critical in the system with several versions.  I don't know if this applies to tool boxes or not.

  This PC also has a LV 2009 SP1 installation, and this version also has the Report Generation Toolkit installed. (even if it is a different revision of the Toolbox as 1.13)

  I know that in the past, several versions of this toolbox were not compatible, which means that a single version of LabVIEW installed might have a job Report Generation Toolkit installed.  But I have been in agreement that it was no longer a problem.  Although it may not be a coincidence that none of the other boxes development runs this code are not installed LV 2009 have.

  Anyone who has encountered a similar problem and found a solution?

  Thank you.

  Before that we unified the version numbers of LabVIEW and toolkit (in 2009), there are cases where it has not changed the version number in the registry for one reason or another on a minor update.  So very well may have installed 1.1.4 and it can still say 1.1.3.  However, assuming that 1.1.4 has been installed, I can't imagine any reason why Word get ActiveX References.vi wouldn't be here.  VI lives at vi.lib\addons\_office\word.llb, so after installation from 1.1.4 to your folder of LabVIEW 8.6, check that the VI is actually there.

  D

• Set the position of the cursor in the text added (to make the part of the text in index) in WORD using Report Generation Toolkit

  I would like to generate a report in WORD using the report generation toolkit.

  Whenever a text is added to the report, the program should put part of the text index. The problem I am facing with is to set the cursor position in the current location of the text.

  Any suggestions?

  Hello!
  I think that's what you wanted (see attachment).

  First, you must set position for each loop, so after adding the table, your cursor index need to increase the number of added characters. That's why I have included the text of the report, Append - to get the position of the cursor at the end.

  Indexing begins with 0, so you need to set the 3 and 7.

  Hope you get what I mean

• VI LabVIEW Report Generation Toolkit elements in a TestStand sequence does not work with a LabVIEW 8.5 run-time engine

  Hi all

  I'm using LabVIEW 8.5.1 and TestStand 4.1. I did a sequence TestStand with a VI in this document, which uses items Report Generation Toolkit. On my machine I use LabVIEW and TestStand development system license. On another machine I use TestStand with basic deployment license and I chose the LabVIEW 8.5 run-time engine in the Configuration of the adapter. Everything works well except this VI with elements of Report Generation Toolkit. The error message shows that the VI is not executable. It works well only after I installed with a trial license and selected LabVIEW LabVIEW 8.5 development system in the Configuration of the adapter.

  I found other posts and a document in the knowledge base with a similar problem: http://digital.ni.com/public.nsf/allkb/8A0E6274D9BD7B1986256F62006AD402?OpenDocument but I am not no EXE files in my sequence, so I do not know how to fix mine. Someone has an idea?

  
  

• Report Generation toolkit for labview 2010

  H all.

  I'm looking to download the 2010 labview report generation tool. When I proceed to download the Toolkit on the site of the national instrumnets, it says that I need LabVIEW 2011 or later in order to install it.

  Is there a version of this for labview report generation 2010 toollkit and can anyone provide a link maybe?

  Thanks for reading.

  Try this: [link removed, can be found on ni.com/downloads OR software downloads, the LabVIEW Report Generation Toolkit 2010 is available to customers with program Service Standard here: http://joule.ni.com/nidu/cds/view/p/id/3247/lang/en, other clients can communicate directly with NOR]

• Hide the Excel using LabVIEW Report Generation Toolkit or active chart legend

  Hello Eveyone:

  I'm working on tool report generation in labview and creat excle report. I create the chart in the report, but I can't hide the chart legend or change the font size using the report generation tools.

  I appriciate you guys time.

  Thank you

  Howdy!

  What version of LabVIEW Report Generation Toolkit you use? Did you take a peek at the .vi LabVIEW example column chart (Excel)

  

  and he looked at using the Excel insert graphical VI and Excel graphic Set do?

• Excel sort using Report Generation Toolkit

  Hello

  The query is related to Excel sort using Report Generation Toolkit.

  At the beginning I write values into three columns permanently. After the while loop, it's stops the third column (C) should be placed in increasing order and columns 1 & 2 also modify accordingly.

  Please find the enclosed. Zip and help me solve the problem.

  Kind regards

  Chick S

  Its best to collect all the data in a table, then sort the values (ascending) then write in excel that will solve your problem in a simple way

• Report Generation Toolkit V9.0.0: Report.vi print does not print

  Hello

  I migrated my project Labview 8.5 Report Generation Toolkit V1.1.2 to Labview report Generation Toolkit V9.0.0 2009 system.

  In this project, I use the report generation tool to print a Standard report with e bit of tables and graphs.

  The Report.vi of printing VI now offers the 41002 error with the text "invalid printer name. I, of course installed the right printer on the machine.

  I Don t one connection at the entrance of 'Printer name' string of VI, because I want to use the default printer.

  In my opinion, West one bug in the Report.vi of printing: If you don t the "printer name" input wire, the vi must use the default printer, but in this case the vi connects the entry blank chain at the entrance of the node method he calls.

  I fixed this bug, but the node method always returns the same error.

  any ideas?

  Thank you!

  Thanks for the link!

  For some reason I can´t find this specific article in the knowledge base (my browser is rerouted always to the German of ni.com version, because I'm in Austria). I tried to search for the exact title of this article and the error message string, but no result...

  I also installed Labview 8.5 and the toolboxes 'old' on my new computer in addition to Labview 2009 and the 'new' toolboxes and tested my program to 8.5. Here, I got an error mentioning the margins and I had to change the margin for printing settings, then worked.

  After reading the article, I applied the same changes to the margins in the 2009 version of my program and it works too!

  Problem solved!

  Thank you very much!

  PS:

  I wrote first of all, that West might be a bug in the new version of Report.vi printing, but I ve compared to the old version and there seems to be no bug, sorry!

  After all, I decided to stay with Labview 8.5 for now, due to another problem:

  It s not possible to "save the previous version" of LV2009 to LV8.5 directly.

  Laview grave failure, when a VI contains a structure of the event I found by looking in the "known issues", and I have a lot of report with the structures of the event!

  I must have the ability to save my projects Labview 8.0 and 8.5. The only way is to save for 8.6 and then save 8.6 to 8.5.

  That s long and nasty!

  Perhaps a future update will solve this problem (without producing new)

• report generation toolkit VI error when running EXE

  A VI in the Report Generation Toolkit (version 1.1.2), Excel find Application Directory.vi, will not work correctly when you run an EXE file.  'Current VI course' block returns the path of the ongoing EXE rather than the path of the Application Directory VI find Excel.  (This would be true for Word find Application Directory.vi.)

  -Joel

  Have you had a look at this knowledge base article? The error is due to exclusion of all dynamics VI.

  Gregory C.

• LV Report Generation Toolkit for Microsoft Office said "this VI or element belongs to a library that has expired or improperly licensed."

  I downloaded the LV Report Generation Toolkit for Microsoft Office for evaluation with LabVIEW 2010. Examples to help get a lot of errors, including "the Subvi is not executable. You must fix any errors in the Subvi before this can run VI. "and"this VI or element belongs to a library that has expired or improperly licensed. "

  I decided that I wanted to evaluate the Toolbox instead of putting an activation code during installation. Installation went well.

  How can I get the examples from this LV package to run so that I can evaluate it?

  A computer restart was costing the day the day to solve the problem.

  Installation of the toolkit does not have a reboot of the system, but it seems to need i.

• How to display the drop-down list box in MS excel by using labview report generation toolkit? pleasepost code block diagram?

  How to display the drop-down list box in MS excel by using labview report generation toolkit? Please post the block diagram of the code so that I can able to generate from the drop-down list box in excel with the menu drop-down...

  Like this. (edition, use the reference forms instead of the reference to the worksheet)

  Ben64

  

• Report Generation Toolkit link hyperlink in a table

  Having bought just Report Generation Toolkit 1.1.2 for Microsoft Office for my LabVIEW 7.1, now I want to create an HTML report that contains a table.  I want to fill the cells of the table with hypertext links to different documents.  I don't see vi in the Toolbox that do this can suggest someone please where I should be looking or the best approach to this problem?

  Hi JohnBoy,

  connection string as your data from the one table with all the tags you need of a link. In your case, your link name.

  It will be useful.
  Mike

• Report Generation Toolkit failure with Win 7 and Labview 2013

  Recently, I had my computer updated to Windows 7 and now I see a problem with the generation of reports (version 2013) tool when you work with Excel files.  If I try to launch the new Report.vi with the selected report type Excel I get error-2146777998.  Do the same with the chosen word finally opens Word, even if it takes 10 seconds, but it does not generate an error.  Selection of Standard or HTML report also run without error.

  I studied him this error on line, but I continue to find .NET and c# forums where everything goes over my head. Anyone have any suggestions?

  I found the solution to this error 2146777998 code source. There are two template files located in C:\Program Files (x 86) \National Instruments\LabVIEW 2013\templates\Report by the name of MSOffice_RGT_Template.dot and MSOffice_RGT_Template.xlt.  The problem came down to these models been corrupted somehow in the new facility. As soon as I replaced the versions from another machine, the problem disappeared.

  As a side note, I discovered the problem by kicking off the MS Office report Express vi and out came a much clearer message aimed me models. Not very well why this message is not included in the different Subvi on the pallet, but life is a mystery.