Request di assistenza by DELL PowerEdge R710 [CF]

Similar Questions

• Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode.

  Hi Sir,

  Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode after upgrading the RAM to 64 GB.

  Arrangement of RAM is made 4 our 16 GB of RAM on 2 channels. I get no error message about the RAM configuration. It is booting in safe mode but not start in normal mode, his hanging during windows startup.

  Please give me guide to solve this problem.

  I thank & regards

  Ramanantsoa D

  Thanks for the reply.

  My version of windows is 32-bit Windows server 2003 Enterprise Edition Service Pack 2.

  Although I have not tried switching/EAP, I will try that and get back to you.

  And again something I have an idea of the installation of windows server 2008 R2 Standard version on this server, it will support? Please let me know Chris.

  Thank you.

• Install.VGZ fails in ESXi 4.1 install on a Dell Poweredge R710

  I have a cluster of ESXi 4.1 six-host running on Dell Poweredge R710.  They start from a USB key connected to an internal USB port.  I did at least 12-20 installs on the same hardware without problem.

  When I try to re - install on the single ISO ESXi 4.1 host via the iDRAC, the installation fails when loading install.vgz with the error message: "Booting: MBI = 0x000100c0, enter = 0x0040024a.

  I studied the two codes and the only suggestion that I get, it's that my hardware is not supported (specifically that my 32-bit processor is not supported).  I do not have a 32-bit processor, so I know that I can surrender.  I downloaded the CPU VMware ISO (file:///C:/Users/pguarco/Downloads/VMware-CPU-Compatibility-e.x.p-160658.zip) compatibility, and my CPU meets all requirements.  Previous installation of ESXi host crashed for unknown reasons, where the re - install.  It is possible, that there is a hardware problem.  Any ideas on how to limit this problem?

  you are doing the right thing. only thing I could thing is bad ISO, (Please make sure that the checksum is correct). and the worst case material PE firmware update.

• Adding additional disk to ESXi 4.1 Datastore on Dell PowerEdge R710

  Greetings,

  We currently have a Dell PowerEdge R710 with 6 SAS das drives configured in a RAID-1/RAID-5 configuration. A drive is configured as a global hot spare. I would add this spare drive in the RAID-5 table, where some virtual machines live, to recover additional space. Has someone managed to do this? Is the only way via the PERC BIOS management utility?

  Thank you!

  I'm not part "raid-1/raid-5.  But assuming that the table is raid-5, then yes it is possible and yes the BIOS utility is necessary.  The hot spare is currently set should be removed from this role, then added to the existing Bay raid-5, but without the ability to select increase.  This will create free space on the raid-5 array on which then a new logical volume can be created, which will be then seen by ESX as a new drive and therefore another data store can be added to this (or it can be added to the first as a measure).  HTH

  http://blog.peacon.co.UK

  Please give points for any helpful answer.

  Unofficial list of transfer USB devices work

• Dell PowerEdge R710 memory upgrade 16 GB (4x4Go) for 72GO with more than 64 GB (8x8Go)

  Hi all

  My Dell PowerEdge R710 is seen 16 GB (4x4Go) now and would like to add 64 GB (8x8Go), it will be total 72GB. Please help me add memory into the slot on the right. Can I do the following as below

  A1/B1 > 8 GB

  A2/B2 > 8 GB

  A3/B3 > 8 GB

  A4/B4 > 8 GB

  A5/B5 > 4 GB

  A6/B6 > 4 GB

  Thanks Robert, I already bought 64 GB (8x8Go) and would like to add to my current server which is running 16 GB (4x4Go). So, please show me how.

  Thank you

  Binh Kien

• DELL PowerEdge R710 and PERC H700 RAID driver for WIn 2008 Std

  Hi all

  I have a DELL PowerEdge R710 with a controller RAID PERC H700.

  I try to install Windows 2008 Std 64 bit, but I can't find the driver. Even for the site web at support.dell.com. Can someone help me.

  THX in advance

  Even if you use a driver of 2008, it should at least recognize it, then you must be using the wrong driver or something wrong :)

  If you are installing 2008 R2, make sure that you use this file:

  If you install 2008 x 64, make sure that you use this file:

  With one, you must first unlock the .exe (right click on the .exe, properties, unlock), unzip / extract the files (run it and make a note of the default location), and then copy the 4 files on a CD, USB, etc., then when Windows tells you that he is not all hard disks, click on the link drivers load below to load the drivers from the media you have chosen.

• Dell PowerEdge R710 - power Ricambio

  Buongiorno,
  Ho need di one ' offer by United Nations alimentatore per PowerEdge R710 con serial number FCL5WN1, dal supporto telephone Dell mi hanno detto di inoltrare the request that.
  Grazie. Saluti.
  Honeywell
  G.Casale

  buongionro, sto contattando via e-mail.

• Internal hard drive inside Dell PowerEdge R710

  Well then clarify first of all. This server is NOT used in a business environment. Its literally being used as a home media server (Yes, exaggerated way I know but I got for free so who is complaining).

  IM currently using a PowerEdge 2950 as my media server, I just took his upgrade, a R710 Gen 2 and I would like to use all 6 bays at the front for hard drives that I can put the plates on instead of 1 for the operating system and then everything else for the media.

  How I would go about installing an internal hard drive, preferably a SSD, inside the R710. I know it has a free SATA port but I can't seem to see the spare power cables or cables molex as there is in the Gen 3 2950 I.

  If it is not possible, it's quite good, but I would like to have installed an internal hard drive.

  I know there is a USB port, but I use Windows Server R2 2012 (probably soon to be Server 2016) but I'm not sure if Windows Server can be installed on the internal USB port.

  If you need to record, or on the label of service I can give you this information.

  Any help would be appreciated.

  Thank you

  Arron

  Thanks for the clarification. It's something that you can try, but it is not supported and there is no guarantee that the SSD will be detected and it works perfectly. Try this P/N GP700 cable

  

• Request offer slitte/representing Dell PowerEdge R610

  Salvo, avrei UN supporto di need by it power edge r610, per poterlo fix nel mio rack.

  Buongiorno, OTS will one ' email by putting manage the request e richiederle it service tag del sistema.

  Grazie

  Marco

• Dell-PowerEdge R710 error

  Hi all

  Our server is flashing an error we've ever seen:

  "Raid W1228 controller.<>

  Has anyone ever seen this message?

  Thoughts, ideas or suggestions are appreciated!

  Thanks in advance!

  Cbcegineer,

  The W1228 error indicates that the RAID battery charger reported to the management server that the battery is missing, can not load the battery (probably due to high temperatures), or the battery is bad. Now, this can also be due to the controller go back very far in the updates as well. You see one of these on the server?

  You can also try to reconnect the cable from the battery as well.

  Let me know what you see.

  You can find the manual here- http://bit.ly/1kRptEr

• Hard drive by PowerEdge R710 [MS]

  Good afternoon,

  It ns. Server DELL PowerEdge R710 (service tag ) ha UN disco che da problemi.

  The machine went up quattro "500 GB near line SAS 6 GB/s, 7.2 k 3.5"disco board hot-plug".»

  Ho tried a ' dare in the giro, my seems to che gli occhiata hard disk the da near Line SAS esistano più non 3.5 ".

  Could by help favore disco UN find by auswechseln quello che sta guastando if?

  Grazie thousand. Silvia (T.E.S.I. S.r.l.)

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione (intervento o):
  1. company name:
  2 address:
  3 City:
  4 Provincia:
  5 cap:
  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione
  1 nome società (is it client code):
  Address 2:
  3 City:
  4 Provincia:
  Heading 5:
  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:
  7 partita IVA

  Speaking saluti

  Manual

• Memory support for the Poweredge R710 speed

  The Dell Poweredge R710 supports up to 1600 MHz memories? As [manufacturer: SNP20D6FC / 16G |] [Dell Part #: A6994465] is compatible with R710?

  Osmanhamid,

  Frequency of memory in servers are affected by a number of factors, including; Speed DIMMS and CPU and memory configuration.

  R710 server supports:

  1. Speed up to 1333 MHz for one module of memory through
  2. Speed up to 1066 MHz for both modules of memory through
  3. Speed up to 800 MHz for three modules of memory per channel. All these speeds correspond to memory single or double modules. Therefore, the speed of 1600 MHz will be down-clocked at a speed suitable depending on the configuration.

  Let me know if you have any other questions.

• Request alimentatore per PowerEdge R710 [CF]

  Buongiorno,

  avrei need di UN alimentatore per PowerEdge R710 take it cui service TAG e F4FRN4J, my dal supporto Dell mi hanno detto di write that. He codice che ho letto sull'alimentatore e n870p-s0, my come posso fare per sapere e thing i prices?

  In hoist foto dell'alimentatore.

  Buongiorno, the sto contattando by mail.

• Request preventivo sostituzione card mother server Dell PowerEdge R610

  Buongiorno,

  Abbiamo need di UN preventivo per sostituzione card mother relative al server Dell PowerEdge R610 fuori co Service Tag GGFN25J.

  Restiamo in attesa di una vs cortese risposta.

  Todas

  Alberto Daponte

  IBN Savio Srl

  Buongiorno, the sto contattando via e-mail.

• [EC] PowerEdge R710 error: 5 E1810 HDD failure

  Buongiorno, di abbiamo UN UN PowerEdge R710 con TAG H1S5S4J che presenta error disco in oggetto. Chiedo UN preventivo como Logserv S.r.l. by the sostituzione nao.

  In attesa di a vostro riscontro, lascio Reed he mio personale interno. 0371-763973.

  Dear client,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi UN message privato.

  Nel caso in cui as aver need di assistenza telefonica is Pagaré a ticket di Assistenza.

  SE if need di una delle quotazione left in sostituzione can rates UN preventivo senza Pagaré the assistenza.

  By request, we have our o di need any it client codice di vecchia quotazione o.

  Nel caso in cui non his di queste information times need che compilasse i seguenti campi:

  -SERVICE TAG-

  By the spedizione:

  1. company name:

  2 address:

  3 City:

  4 Provincia:

  5 cap:

  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione (is different)

  1 nome società (is it client code):

  2 via:

  3 City:

  4 Provincia:

  Heading 5:

  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:

  7 partita IVA

  Speaking saluti

  EC