Rescue and recovery lists no backup on USB Iomega eGO drive

Hello

I have been using an Iomega eGO external backups USB drive.

I was able to identify and remove (if necessary) backups in Windows 7 and rescue & recovery running, but I can't get the list of backups at the start of a recovery in rescue & recovery DVD.

Basically I replaces unencrypted with a SSD hard drive that supports encryption.

The goal was to use a full backup immediately before removing the HARD drive to restore the complete system.

At the start of the recovery DVDs, recovery utility & rescue lists not all backups, even when the check box for the list of backups on other systems is checked.

It makes no difference if the selection of THE places or USB external drive.

Any ideas?

Backups are not much good if you can't get back them.

If my old drive did not then I would be in a worse state than this. I can't say I'm impressed.

Well, I've finally sorted this issue.

I tried to create a new recovery disk.

I even tried the recovery time in Windows and see what backups it detected. Yet once, I drew a blank.

The question was this:

On my W510 at least, none of the USB3.0 ports are recognized by Lenovo rescue and recovery software when you select the USB storage device. Once connected to a single USB 2.0 port the USB eGo has been recognized and listed backups.

Unfortunately, this means a minimum of 6 hours to restore from a full backup!

Tags: ThinkPad Notebooks

Similar Questions

  • Rescue and recovery cannot delete backups

    Hello

    I have problem delete old backups with Rescue and Recovery - always when I try to delete them, it seems to work, but it is not, it never ends... I tried to remove one of all backups, only the last or only the oldest or all of them together, but without effect. I have 6 backups about 45 GB together. And by the way that r & R does not well at all - also when I click on optimize backup storage space, it does not work...

    Eventually, it is normal that when deleting old backups, computer seems cold and it takes a long time, but I don't know if it never ends.

    I have the latest version of Windows XP Pro SP3, R & R 4.21.0016 R61.

    Is there a solution?

    Thank you very much!

    V.K.

    Uninstall rescue and recovery of add/remove programs. It will remove the backups in this way.

  • With the help of Rescue and Recovery to make backups of 3 different machines

    Hello, I have three laptop Thinkpad T400, X 61 and R61i. I want to back up by using an external hard drive. The HD is divided into three partitions, the smallest of X 61, the middle of R61i and most importantly - for T400. I backed up all my laptops in the appropriate partitions (base backups), but now, so I want to make partial backups, they go to the bigger partition (for the T400). Is it possible (and how) do R & R to always use the same partition for each laptop while safeguarding it?

    A few notes, to respond to your previous post:

    (1) Sysprep is used by administrators to deploy and image system to other machines. Basically, the system starts standalone RNR and save the image (drive C and the same HARD drive partitions) on the service partition.  Comment enumeration pleasure has to with additional partitions on the C drive HDD.  For sysprep to work, additional partitions must be of type Extended. The windows PE, is a windows "skimpy" PRE environment. For win7, the EP is based on Vista with a small set of win7 features added.  Thie PE is used for developers (as Lenovo) to install their systems.

    * None of this applies to a user at home like you and me *.

    (2) the logic used in the RNR for the GUI vs bent the advanced GUI are DIFFERENT.

    Example: the user has part C, D and E on C disk HARD drive.  Uses advanced parms to set backup (local) to go to E drive.

    If the backup through the advanced graphical interface, drive E is honored.

    If the backup is performed through simple GUI, the partition with the largest free space is used.

    Note: using the Second HARD drive don't offer NO choice to designate a partition target of \RRbackups.

    (3) view of backups.  It's clearly too.

    When a backup is performed, and RNR is locked on him, it will REFRESH the registry entries for the content of backup.dats in the \rrbackups folder. Subsequent backups of view will probably be read from the registry. That is to say no record of reloading. Simpified mistletoe might once again, just to use the registry, the locks of GUI in the new backup folder.

    (4) your letter removal/restoration

    a: I have no idea how autonomous RNR will react to the 3 folders on the second \rrbackup, IE the part 1, 2, 3.

    b. If rnr backups locked in the wrong \rrbackup folder, you will have a total mess. A symptom of this: you take a basic (full) backup, and the next backup, which should be an incremental, is actually another full backup.  This error could occur if you deleted the wrong letters.

    (5) you have a mess.

    If I save it again this PC, R & R is a point instead of a differential backup<>

    It would take a lot of work on you end to look in the backup files.  Not worth it.

    Again, the simpifed GUI backup use different logic. He likes the larger partition.

    From what you say, you used simplified and got the base of the machine backup 3 all go good part 1, 2, 3.

    Somewhere in this mess, he locked in a \rrbackups without a base backup folder and took another backup.

    who knows.

    ==

    Release notes:

    Review 4
    ----------------
    Location of backup changes when you select a smaller partition through the advanced interface of the Rescue and Recovery program.

    In the advanced interface of the Rescue and Recovery program, you select a partition more small capacity on your local hard drive as the backup location. Then, you switch to the simplified interface to create the backup. However, the backup is created on the partition with the highest capacity.

    To resolve this problem, back up your system in the advanced interface of the Rescue and Recovery program after you have selected the backup location.

    ===

    The solution is the cleanest way to follow. I would always use the GUI advanced for now on.

  • Rescue and recovery cannot find backups - EXCEPT in the restore function. Help

    I recently optimized files, including placement
    the disk - machine now flying.  "I wanted to start from scratch with R & R).  Thus,.
    delete all local backups and USB.

    I started a basic backup - initialized manually, close,
    restarted, returned the top could not backups - display Message "No. BACKUPS
    FOUND "hen"show all the backups", or"delete backups"Advanced"
    menu.  However I can find them using the RESTORE OF THE BACKUP.

    Repeated starting a new backup, same results exactly, except
    now I have two BASE backups.  I even started in the R & TV R
    environment may find things out there.  No luck - no possibility to launch a backup Boot TV
    environment, but could restore from the backup.

    I don't see any other choice other that uninstall 3.01?  Do you have?  However, the most recent
    version there is 4.22... Any reason why I shouldn't go to the
    new version?  I read all warning, installation notes, bugs, etc., none seem to apply to me.

    If anyone has any ideas, I would be happy, or if you know any
    reason why 4.22 isn't a good option...?

    Thanks in advance

    Type of computer rescue & Recovery version 3.01 T60 = 2623 - model.
    D7U

    All, I finally managed to replace the version of R R & on the Master Boot Record.

    First, I started with a R boot drive at & R.  You can either use one you did with R & R when (if) you put always a full backup on CD (which I do every year), or the startup disk (a, a) that Lenovo is sent to you with the 7 product Recovery CD, you can restore your PC to specifically state that you received from the factory or store (if you have purchased again).

    R & R starts automatically on startup with the version of R CD R & makes the startup disk (be it when you or Lenovo is the startup disk.)

    My experience is that after you start with this CD, I shut down R & R normally, then restarted the computer by using the MBR (pushing the Thinkvantage or F11 key at the beginning in the trunk) and voila - it starts with the same version that you started with the CD in the last step.

    I also discovered that if you use R & R to restore to a time when the Version of R & R was different from what is working on the MBR, which also change the MBR.  Again, both are good information that will certainly be useful trivia some time.

    Thanks again to all who jumped and provided information that ultimatelly led to the solution

    concerning

    Fred

  • Rescue and recovery 4.2, do not recognize the Ultrabay drive

    I have the T61 and strives to save my primary HDD to my secondary HDD in my housing Ultrabay.  For some reason, it is not recognize a drive is there, but I have D: up and and am able to access the files without any problems.  What I am doing wrong?  BTW, I save on my USB stick thin and currently it is not connected.

    George

    Check the disk management.  It seems that the drive can be configured as a dynamic volume, which does not recognize RnR.

  • Rescue and recovery of backup fails: current drive does not match the previous backup

    I have just rebuild my T60p with a new hard drive for the recovery of Lenovo CD via the rescue and recovery CD. Once the system restore is complete and the laptop running, I took a full backup using Rescue and Recovery. This backup is the C:\ drive which was the only drive I had and was on a USB hard drive.

    In recent days I have the C:\ split in two, giving me a new D: drive, patched all system software, added my own data, and obtained the machine configuration as I want. I've also trashed the R & R hidden partition so I could make a bigger drive D:\ and created my own bootable CD R & R for future use - not that it makes a difference.

    Now, I want to take a second backup with the Rescue and Recovery tool. Naturally I want to back up the disks C:\ and D:\, but the backup fails saying: -.

    "The last backup of this system include the following drive letters: C: .

    Your system is now back up these drive letters: C: d:

    Please define drive letters, as they were before and Christine backup. You may need to exclude partitions created since the last backup. »

    Is there anyway that I can make a backup of disks C:\ so my D:\?

    The only option I see is to delete my previuos backup and I don't want to do because it can be useful in the future if I still want to restore my system to original state manufactured.

    Suggestions anyone?

    Thanks, Iain

    Given that you have saved on an external USB disk your backup will be saved in a

    the folder named RRbackups.  If you rename this file I - think - R & R going to think

    you do not have any backups, so the next backup will be a 'base '. If you

    never have to restore the original of your 'base' backup, rename the folders should allow.

  • Rescue and recovery blocks for hours at 0% of backup

    Hello

    My R61 ran quite OK, but slower over time. I got through rescue and recovery made a backup of the entire system on an external hard drive. (I had come back to XP and recently did a total system backup on the external HD). So I haven't started the rescue and recovery, thinking that he should simply reinstall it previously saved system. Alas at step 2 the progress of rescue and recovery, the new generation of the system stopped. Black screen with the message: «backup system is...» 0 % ». Here I wait for hours. Nothing progesses.

    What should I do? Island of 'progress' is already happening for 6 hours! (I see that my external HD flashes from time to time, but the computer does not seem to do anything).

    What should I do? I fear that if I press the power button to restart the computer, I will plant it completely.

    Please help me!

    Thanks in advance

    Roger

    Rescue and recovery hung several times for hours. Yet, it seemed to work after 20 hours. Puhhhh...

    Lenovo at: Your UI during the rescue and recovery process is ineffective. He left me without any feedback for hours. Almost, I rebooted the computer during critical backups. Here you certainly should help the user to understand what to do and what not. How can I find out, it's OK to have a bar saying 0% progress made for 8 hours.

    Even now, I don't know what to do. The computer restarts, windows is OK. But now I can turn off the computer or is always something during rescue and recovery. The last time, he says, it is step 2 on a total of 5 steps. Is it still now something in the back? The rescue is complete? Where is the message telling me, he did the job.

    All users: be patient, do not hit anything it either by running a rescue and recovery.

    Lenovo: By the way, I had - after installing my computer with xp - makes a backup of the system. that I repeated it several times. When my HD arrived full, I remove some of the older versions, because anyway, I had the newer versions which worked perfectly. Alas, I didn't, which obviously rescue and recovery done a system save, later versions are simply updated. By removing the first version, I lost all the! So, I ended up having no actual backup of a validating at the beginning.  In short: Rescue and Recovery can be a tool very well for an IT expert. For the average user, there are much too many traps. Lenovo: Try to it you like-centered-design user instead of the user Board Chinese garbage, if in the future, you want to keep as «almost IBM» brand name For me, Lenovo - in this regard - is more "almost Chinese It-garbage".

  • Question of rescue and recovery, and Client Security solution

    I have a thinkpad edge e220s for home use and I am trying to understand that these two thinkvantage tools will be of no use to me since I'm not on a corporate network or whatever it is (all marketing materials HE mentions admins etc.).

    Is the rescue and recovery just a backup solution with imaging of disk (as ghost)? I use a drobo for all my data storage, so I am not too concerned about backups as the drobo offers redundancy in the event of disk failure. The laptop has a SSD which doesn't have a lot of capacity if I don't want unnecessary tools that will have a lot of space. However if the rescue and recovery offers really useful features then I might consider its installation (and not using the backup feature). I could not make out what marketing materials meant by the solution of a single button for viruses and crashes.

    Second, the client security solution features other than Vault/Manager password on my model? I'm already using the beta version of the new (4) version of password manager which is autonomous and requires no client security solution. Again once the marketing material does not help a user at home like me understand very well.

    Any help will be appreciated!

    Based on your description I don't think rescue & recovery or Client Security Solution any value for you.

  • Rescue and recovery question

    Can I do the following with the installation of a new hard drive in my x 200 under xp pro update with all SPs and patches victory. ?

    1 create a Rescue and Recovery Using ThinkVantage disc.

    2. backup the 'information' using windows backup on an external hard disk utillity.

    3. install the new hard drive in my x 200

    4. start x 200 with Rescue and Recovery disc

    5. connect the external hard drive and restore 'Any Information' using the xp utillity

    6 make essentially a version cloned my original hard drive in the hard drive installed one.

    Thanks for any help/suggestions.

    Of course, you can use your method

  • Rescue and recovery - how to back up the entire operating system?

    Hi all

    Maybe I'm looking for something that is not supported, but since I got here, then we are

    I'm running Windows 7 Pro (x 64) on the T410.

    Rescue and Recovery 4.31

    I divided my HARD drive into 2 partitions: C for the OS and D for data.

    I have a disk storage network, so, apparently, I did not need to backup the data that is stored on drive D (already to store all my data on the NAS drive)

    What I want to do is to set up the R & R to backup all my drive C (the OS only)

    How can I go about to do?

    Thanks a lot for your comments

    You can do this in "Advanced" mode of Rescue and Recovery:

    1. open Rescue and Recovery

    2. click on the arrow next to "Launch Advanced Rescue and Recovery" in the lower left corner

    3. click on 'Set schedule and preferences' on the right side

    4. click on your "Include partitions" D: drive on the right, so that d will not be saved.

  • Rescue and recovery will not restore backup files it finds when starting

    I recently had a system problem on my Lenovo computer and had to recreate the image. When I try to restore my backup using rescue and recovery (R & R), they prove inaccessible. How to access these backups?

    Details of the options selected in R & R are attached, as an image on the screen of the settings dialog box.

    Running R & R, backups (on an external HDD USB) are visible and can be selected as expected. When the computer restarts in the space of restoration work, after a warning do not turn off the power, you get the error message "the restore has failed because the backup was not found at the specified location. Accept that the computer restarts in Windows. In this case regardless of the options selected at the start of R & R.  Where appropriate I select the USB external storage device in the Setup program and select a backup of those listed.

    I also tried updating all Lenovo utilities, including R & R. The option 'get new updates"errors when downloading the package information Lenovo Service Center (1 on 1) at the helm of the 30% with the error" Exception should not met!

    A lot of ongoing issues.  Many Lenovo post deal with each issue. Intel, system update, create a recovery to the USB media.

    For now, I'll address your problems of rescue and recovery. It seems that your system worked well, until a database had records in doubles in it, and you want to use RI to restore a backup on your USB.

    Then you have attempted a return to the factory, which show a lot of questions.

    If I understand your request, you want to restore your system to some time in the past, using a backup RNR. Either last week or 2 months ago. Something that works.

    ===

    RNR will save all partitions on the disk C DD.  It never saves another HARD disk.  2 readers warning has been around for a while. If C and D are on the C drive, HARD drive, it will run through RNR.

    Single file restore only runs on the windows RNR.  But there is no need to restart standalone RNR (pf11 during startup).

    It is ok. At least the RNR version on windows can find and restore your USB /rrbackups, of 5 min or 30 hours. This works.

    ==

    Factory restore installs a RNR version right here. This version probably does not match the version on your USB. If you started the RNR factory with the USB version version, you might expect not found messages.

    ===

    On your system windows today, please state the version installed.  Start using pf11 and indicate the version installed.

    You cannot create recovery media and rescue on the same device. Your luck if anything boots on the USB (other positions).

    Essentially, the RNR standaone version must match the /rrbackups on USB.

    =

    How do restore you to the factory settings? pf11 through the work of rnr or external cd/dvd?

    You are the original owner of the machine?

  • Delete backup files Rescue and Recovery after the uninstallation of r ' not R

    During the upgrade to Windows 10, Rescue and Recovery has been automatically uninstalled.  I had neglected to remove the external drive backup files before that.  I would like to locate these files so I can delete them manually.  What files are backups Rescue and Recovery?

    Y at - it a compatible version of Windows 10 Rescue and Recovery?

    I leave your external USB - HDD intact right now.

    You might like to win 10, win10 could not meet your needs and turn.

    A Loved via RNR win7 would be nice to have, just in case.

    If it comes to the test computer, your decision.

  • Missing from the 40 GB hard drive! (R61) - Rescue and Recovery said there is no backups?

    I have a laptop R61 140 GB running on Windows Vista. It is around the age of 18 months.

    Explorer Windows says that 82 140 GB GB is used.

    When I add each folder I get only 45 GB of used space. All I really on this computer is music 26gig & some vacation photos.

    I had this problem since I first got the computer.

    I looked through discussions here that suggested that the backups can be the cause, and a program called Rescue and Recovery was the problem.

    However, when I opened this program it says that there are no backups available. However, this program is no doubt trying to run on my computer every Wednesday I get a popup saying my computer was turned off and I want to run it (I say no).

    Tools SW file is 2 GB.

    On the windows Explorer when I right-click I see there is something called 'points system recovery', there are many. However, I can't understand it here, where the data is stored, or how I would delete it.

    Please help me because it's very frustrating because I have about 40 GB of music I would like to pass through but right now that uses a lot of my remaining space.

    Download this and you can see everything on your hard drive http://www.pcworld.com/downloads/file/fid, 64425-page, 1-c, downloads/description.html

  • Rescue and Recovery backup not file system - without error message

    I use, since 1985 the first IBM, Lenovo then. I was very happy, my next Lenovo will be bought next spring.

    But I'm just very disappointed. Daily tracks of rescue and recovery on the local disk, which later are copied to a backup drive.

    The program has never shown an error on the screen and still run perfectly-, I thought!

    A few days ago, I got a Windows error for the first time. There are a lot of missing files.
    I restored the system on the R & R and reboted. But cannot start.
    With a boot disk, I booted the system and could now see that all the Windows directory was empty!

    Unfortunately, I can not in R & R files see what files and directories contain a backup? Or can you?

    Question 1:

    So I would like to know how if someone can enlighten me.

    Then I started to investigate on what had happened. In c:-Library SWSHARE I found some files that I see is connected to R & R.
    In the engine.log file, I see R & R has written a large number of error lines, of which a part is reproduced below. File dates to 2011 and there are errors all the way

    Question 2:
    Why the program not onscreen when R & R run display errors, so that the user knows there are errors?

    Now I'm sitting at the bottom with a long nose, after 2 days and nights, trying to find a solution and restored the system several times and do not know how the file system works will come back on my PC so normally again.

    Be more happy if someone can tell me how to solve this problem.

    Here is a selection of error lines:

    Thu 17 Oct 08:41:59 ENGINE 2013: failed to send an IOCTL_FFDRIVER_ENCRYPT_OFF
    Thu 17 Oct 08:43:38 engine 2013: br_funcs.exe - version is '04.17.20a.00 '.
    Thu 17 Oct 08:43:40 engine 2013: CopySAM called with pwszDestination = "C:\RRbackups\common".
    Thu Oct 17 08:43:44 engine 2013: out of CopySAM with dwRet = 0 x 00000000
    Thu 17 Oct 17:00:09 engine 2013: br_funcs.exe - version is '04.17.20a.00 '.
    Thu 17 Oct 17:00:09 engine 2013: DeleteSISAndExclude (delType 1, drive letter C, Destination 'C:\RRbackups', level 12)
    Thu Oct 17 17:01:25 engine 2013: DeleteSISAndExclude out with return code 0 x 00000000
    Thu Oct 17 17:01:59 2013 engine: br_funcs.exe - version is '04.17.20a.00 '.
    Thu Oct 17 17:01:59 2013 Verbatim: WriteDriveContents (DriveLetter ='C:', Dest = 'C:\RRbackups', level = 13, SleepCount = 0, DeviceType = 1, dwOptFlags = 0 x 00000001)
    Thu Oct 17 17:05:48 2013 Verbatim: 0x00000010883e6399 - space required before compression
    Thu Oct 17 17:05:49 2013 Verbatim: 0x00000001ef30e1bf - estimated space required after compression
    Thu Oct 17 17:05:49 2013 Verbatim: 0x0000001dae2dd000 - currently available disk space
    Thu 17 Oct 17:07:27 2013 Verbatim: can't get exclusive lock for the entire file 'C:\Documents and Settings\Bendt Skov.DK\Application Data\Mozilla\Firefox\Profiles\gbkxfkqd.default\cookies.sqlite-shm' - WinRC = 0x00000000
    Thu 17 Oct 17:07:30 2013 Verbatim: can't get exclusive lock for the entire file 'C:\Documents and Settings\Bendt Skov.DK\Application Data\Mozilla\Firefox\Profiles\gbkxfkqd.default\healthreport.sqlite-shm' - WinRC = 0x00000000
    Thu 17 Oct 17:07:31 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\Bendt Skov.DK\Application Data\Mozilla\Firefox\Profiles\gbkxfkqd.default\parent.lock" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu 17 Oct 17:07:33 2013 Verbatim: can't get exclusive lock for the entire file 'C:\Documents and Settings\Bendt Skov.DK\Application Data\Mozilla\Firefox\Profiles\gbkxfkqd.default\places.sqlite-shm' - WinRC = 0x00000000
    Thu 17 Oct 17:07:34 2013 Verbatim: can't get exclusive lock for the entire file 'C:\Documents and Settings\Bendt Skov.DK\Application Data\Mozilla\Firefox\Profiles\gbkxfkqd.default\webappsstore.sqlite-shm' - WinRC = 0x00000000
    Thu Oct 17 17:08:28 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\Bendt Skov.DK\Local Settings\Application Data\Microsoft\Windows\UsrClass.dat" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:08:30 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\Bendt Skov.DK\Local Settings\Application Data\Microsoft\Windows\UsrClass.dat.LOG" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:02 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\Bendt Skov.DK\NTUSER." DAT' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:09 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\Bendt Skov.DK\ntuser.dat.LOG" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:15 engine 2013: CreateFileW failed for the file 'C:\Documents and Settings\Application Data\Microsoft\Windows\UsrClass.dat.LOG LocalService' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:16 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\LocalService\NTUSER. DAT' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:17 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\LocalService\ntuser.dat.LOG" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:18 engine 2013: CreateFileW failed for the file 'C:\Documents and Settings\Application Data\Microsoft\Windows\UsrClass.dat.LOG Settings' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:19 engine 2013: CreateFileW failed for the file ' C:\Documents and NetworkService NTUSER. DAT' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:20 engine 2013: CreateFileW failed for the file "C:\Documents and Settings\NetworkService\ntuser.dat.LOG" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:09:25 Verbatim 2013: cannot save short name of "C:\hiberfil.sys" - WinRC = 0x00000020
    Thu Oct 17 17:09:25 engine 2013: impossible to attributes of record for the file "C:\hiberfil.sys" - WinRC = 0x00000020
    Thu Oct 17 17:09:47 2013 Verbatim: cannot save short name of "C:\pagefile.sys" - WinRC = 0x00000020
    Thu Oct 17 17:09:47 engine 2013: impossible to attributes of record for the file "C:\pagefile.sys" - WinRC = 0x00000020
    Thu Oct 17 17:11:50 engine 2013: CreateFileW failed for the file "C:\Program Files\Bitdefender\Bitdefender\onaccess.dat" and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:19:49 motor 2013: jump from the C:\Program Files\Bitdefender\Bitdefender\onaccess.dat file at the request of the user
    Thu Oct 17 17:23:10 engine 2013: CreateFileW failed for file ' C:\Program Files\Common Files\Bitdefender\Bitdefender threatens Scanner\smartdb - ntfs.db' and the reason was not a sharing violation - Windows RC = 0 x 00000020
    Thu Oct 17 17:33:13 engine 2013: jump to the folder C:\Program Files\Common Files\Bitdefender\Bitdefender threat Scanner\smartdb - ntfs.db at the request of the user
    Thu Oct 17 17:37:08 2013 engine: BackupFile failed - unable to "C:\WINDOWS" BackupRead - GetLastError() returns 0x00000020
    Thu Oct 17 17:37:08 2013 engine: unable to BackupFile directory C:\WINDOWS - dwRet = 0 x 00000516
    Thu Oct 17 17:37:09 2013 Verbatim: can't get exclusive lock for the entire file "C:\Documents and Settings\Bendt Skov.DK\Local Settings\Application Data\Microsoft\Outlook\outlook.pst" - WinRC = 0x00000000
    Thu Oct 17 17:37:13 2013 Verbatim: can't get exclusive lock for the whole of the file "C:\Documents and Settings\Bendt Skov.DK\Local Settings\Application Data\Microsoft\Outlook\Personal folders (1) .pst '-WinRC = 0 x 00000000"
    Thu Oct 17 17:37:15 2013 Verbatim: can't get exclusive lock for the entire file "C:\Privat\bendtskov-hotmail Arkiv.pst" - WinRC = 0x00000000
    Thu Oct 17 17:37:16 Verbatim 2013: can't get exclusive lock for the entire file "C:\Privat\morkebjerg-hotmail Arkiv.pst" - WinRC = 0x00000000
    Thu Oct 17 17:37:17 2013 Verbatim: WriteDriveContents exit with return code 0 x 00000000
    Thu Oct 17 17:37:25 engine 2013: br_funcs.exe - version is '04.17.20a.00 '.
    Thu Oct 17 17:37:25 engine 2013: CopySAM called with pwszDestination = "C:\RRbackups\common".
    Thu Oct 17 17:37:26 engine 2013: out of CopySAM with dwRet = 0 x 00000000
    Thu Oct 17 22:34:38 engine 2013: br_funcs.exe - version is '04.17.20a.00 '.
    Thu Oct 17 22:34:39 engine 2013: CopySAM called with pwszDestination = "C:\RRbackups\common".
    Thu Oct 17 22:34:42 engine 2013: out of CopySAM with dwRet = 0 x 00000000


  • N500 Vista and Lenovo rescue and recovery Care do not backup

    I would use Lenovo Care - Rescue and Recovery for backup system on DVD. But R & R cannot do, and I don't know why. What is happen? I see that no stop window with the message "a backup on your system is underway" but progress are always 0%. I made the backup several weeks - then backup was corectly. Unfortunately now I have a problem with her.

    my laptop is lenovo n500 and Vista 32

    I solved problem myself in new R & R 4.21 instalation

Maybe you are looking for

  • Replacing the motherboard on Satellite Pro 2100

    Can someone tell me where I can get a replacement motherboard, as when I turn it on, the power light flashes yellow indicating an abnormal voltage in the electric power system? I thought it was the power supply, but the local pc repair center said it

  • WRT110 / Range Extenders

    Can I use a WRT110 as Repeater/Extender range for my main WRT160? I would like to see if I can leave my neighbor to access my internet connection. Thanks a lot, I'm a bit lost with this stuff! Bill

  • PowerEdge 2950 - Win2012 R2 - drives not found

    Trying to install Win 2012 R2 on a 2950 I picked up, but am not able to find the drivers I need so it can recognize the discs.  I had a similar problem with a 1850 and it was my RAID drivers... but this server doesn't seem to be using RAID (nothing h

  • Support different OS

    I have read many topics on the different versions of the operating system, but I have a few questions. Unfortunately I don't own a Blackberry, so what I did is done by simulators. I'm totally new to Blackberry App programming, so, when I started I do

  • EchoSign for Salesforce - disable signed document being the subject of a push for Salesforce

    HelloSending documents from inside Salesforce using the Send button, all documents signed to Echosign are rushed back to Salesforce as an attachment to the associated list of the agreement.  Anyone know how to disable this feature?  I need to change