Resolve error: series 1200 Protocol not supported network home

Similar Questions

• Error: cannot read file, Protocol not supported while watching a video

  Original title: can't access a video

  I try to watch a video and I get a message, can't read file, Protocol not supported, this is something new? never seen this happen until today.   I'm not good with computer, so I have no idea what to do now? I hope someone can help me

  Hello

  You can read the following article and check if it helps:

  Error message when you try to use Windows Media Player to stream audio or video from Windows Media Services: «the specified protocol is not supported»

  http://support.Microsoft.com/kb/940029

  Also check out the following link and check if it helps:

  http://social.answers.Microsoft.com/forums/en-us/xppictures/thread/02a93593-F483-4B50-836C-391acfbe8b83

  Hope this information is useful.

  Jeremy K

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error 1606. Could not access network location by default.

  Anyone know what this error message 'Error 1606 could not be accessed by default network location', or how to fix it?
  Yes, I know that it is almost the same as http://support.microsoft.com/kb/886549 but this difficulty does not work.

  The newspaper msi shows this when I hit retry:
  Error 1606. Could not access network location by default.
  Error 1606. Could not access network location by default.
  = Logging stopped: 06/02/2012 18:53:30 =.

  1. have you tried all of the methods in this article steps: http://support.microsoft.com/kb/886549

  2. have you made any changes on your computer before this problem occurred?

  3. When you receive this error message?

  4. you install any application?

  This problem occurs because there is incorrect entries in the Shell folder of the user who is logged on to Microsoft Windows. When Windows Installer goes to the sale of Shell folder of the user who is logged on to the computer, Windows Installer cannot locate the correct entry.

  Follow these steps and check.

  The Troubleshooting Manual in the link above steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  a. click Startand then click run.
  (b) in the Open box, type regeditand then click OK.
  c. look for, and then click the following registry key:
  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders
  (If the command is missing, you can add a command)

  d. in the right pane of the registry editor, double-click common administrative tools.
  e. in the value data box, type the following line, and then click OK:
  %ALLUSERSPROFILE%\Start Menu\Programs\Administrative of Directors
  f. on the file menu, click Exit to quit the registry editor.
  g. restart the computer.

  Thank you

• Get codes error like "error 80070005" or "could not access network location" or "internal error" when you try to open Acrobat or itunes or access some Web sites.

  I am doing various codes "error 80070005" or "could not access network location" or "internal error" when trying to access acrobat or itunes or some Web sites or that he was trying to perform certain actions such as uninstalling programs.  Here are some of the problems.  A couple of weeks everything worked very well, now there's something blocking me and it's extremely frustrating.

  Hello

  Make sure that you are logged on as administrator.

  Don't forget to check the antivirus product issues and security as a 3rd party firewall (Comodo, on the one hand, a
  has been known to cause this problem.

  It is a very difficult to solve.

  Products of security/antivirus/antispyware are a known cause, so you can turn them off like
  as the test (and that sometimes not really totally removes their influence).

  How to restore the security settings the default settings?
  http://support.Microsoft.com/kb/313222

  The problem here is slightly different, although the solution may be the same.

  Error message when you use Microsoft Update or Windows Update Web sites to install updates on Windows 2000.
  Windows XP and Windows Server 2003: 0 x 80070005
  http://support.Microsoft.com/kb/968003/

  It is usually a permissions problem:

  Please check this link and those that he sites.

  Work your way through my 3 posts here.
  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/200f5140-c2dd-48a5-8CDB-0d8c82ade3cf

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Try to access some Government Web site, but get message that it uses a protocol not supported.

  Original title: compatibility

  I'm doing something online with a governing body, but whenever I try to go ahead he said he uses a protocol not supported... can you help me please

  Hi Marystack,

  Thanks for posting your query on the Microsoft Community.

  According to the description of the problem you are trying to access some government site but get message that it uses a protocol not supported. This question might be if you are connected to a network domain, or there is no restrictions applied to surf these sites.

  If you use Internet Explorer and cannot open certain websites then, there may be a chance that the site is not compatible with Internet Explorer. So, I suggest to open these websites in compatibility view and see if it helps.

  • Open Internet Explorer.

  • Open Web site which is getting blocked.

  • To open the toolbar, press the alt key pressed .

  • Now, click on Tools.

  • Then click on compatibility view settings.

  • You will see the name of the Web site under Add this Web site, to do this, click Add to add this Web site.

  • Close the window and restart your computer.

  Try it out below mentioned methods and see if it helps you to solve the problem.

  Method 1

  If the problem persists, try to trust these websites by following the steps mentioned below.

  Step 1: Open the trusted sites

  1. Open Internet Explorer.
  2. Press the Alt key to display the Tools menu.
  3. In the menu, click Tools.
  4. Now, click on Internet Options.
  5. Click on Security tab.
  6. Select Trusted sites.
  7. Click the Sites.

  

  Step 2:

  Add the trust Web site

  1. Enter the address of the site you want to add.
  2. Click on Add.
  3. Close the open windows of Trusted Sites and Internet Options .

  

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  The upgrade from Vista to Windows 7

  I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  Have you tried to do an upgrade installation or a custom installation?  A custom installation requires you to back up your files and settings with Windows Easy Transfer and then reinstall everything after installing the new.  If an update install does not install work, you need to do a custom.

  In addition, a Windows 7 Anytime Upgrade will not work and you get a message from a platform if you have bought a UA and tried to use it with Vista.  Vista upgrade requires a detail, a copy in the Windows 7 box.

• I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  Hi Izzy Nagar,

  ·         Exactly when you receive this error message?

  ·         Did you do changes on the computer before the show?

  ·         Do you have any extended monitor connected to the computer in the past or at the present time?

  Follow the suggestions below for a possible solution:

  Method 1: You can try to reduce the resolution of the screen (lower), then check if the message still appears.

  Check also if the refresh rate of the monitor is set correctly and check the manual of the monitor for assistance.

  Ways to improve display quality

  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-display-quality

   

  Flicker of the correct monitor (refresh rate)

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  Method 2: Use the option ' enable video low resolution (640 × 480) "start, then update your video card driver and check if the problem still persists.

  a. click the Start button, click the arrow next to Shut Down and then click on restart.

  b. do one of the following:

  ·         If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  ·         If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  c. on the Advanced Boot Options screen, use the arrow keys to select activate video low resolution (640 × 480) and press ENTER.

  d. connect to your computer with an account of a user who has administrator rights.

  e. If you can see your desktop, there is a problem with your video card. Try to update your video card driver. For more information, see the article:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  I hope this helps.

• Windows 7 rdp connection error "the request is not supported.

  I have a Windows 7 desktop computer that is set up to allow remote access to the desktop.  If nobody is logged on to the desktop computer, people can RDP in without problem.  If someone IS connected to the desktop computer, and then try to RDP from a different computer, he comes to the login prompt, but returns the error "the request is not supported" after entering the name and password.  Any ideas how to fix?

  Hello

  The question you posted would be better suited in the the TechNet Forums. I would recommend posting your query in the link below.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  Hope this information helps.

• WebVPN - error: access method is not supported for the capture of WebVPN

  I'm watching a capture of webvpn on the SAA. I start the capture:

  test type webvpn user capture (entering a valid user name)

  Then I connect to the ASA to try to see track with "Using a browser to capture displayed data" as described in the setup guide.

  https:// / admin/capture/test/OCAP

  After login, I get this message in the browser:

  "Error: access method is not supported for WebVPN capture."

  If I stop the capture (capture test) before you try to connect, the error in the browser is:

  "404 not found".

  The/admin/capture/test/OCAP requested URL was not found on this server. "

  Any ideas greatly appreciated. Thank you!

  After some research, I finally found it

  DOC: Webvpn catches are recorded only in zip format

  
  

  CSCtg79320

  Symptom:

  WebVPN captures are only saved in zip format.

  Conditions:

  According to the following doc:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/WebVPN.html#wp1153077

  WebVPN captures can be recovered in the pcap format using the browser, which is incorrect. The document must be corrected.

  Workaround solution:

  N/A

  Thank you for your time and cooperation

  Portu.

  In case you have any other questions please note all useful messages and mark this question as answered

• When I use the Client for NFS provided by Windows 7, I'm unable to connect. The "mount \\ip address\share Z:" command fails with the error code "the path not found network".

  Identification of customer's Windows 7 NFS UID GID information

  I am trying to connect to the Windows 7 Client NFS on a server running on a computer (VxWorks) NFS.  I am able to properly connect Client NFS software by a 3rd party on the NFS server.  However, when I use the Client for NFS provided by Windows 7, I am unable to connect.  The \\ip address\share Z: mount"command fails with the error code"the path not found network ".  I can't do a ping of the computer running the NFS server.

  The NFS Client operating system: Windows 7 Ultimate, 64-bit

  Data captured by Wireshark

  MOUNT V1 EXPORT call 3rd party client
  Identification information Flavor: AUTH_UNIX (1)
  Length: 32
  Stamp: 0xc7065970

  Machine name: PC
  UID: 1000
  GID: 1000

  MOUNT V1 EXPORT appeal of the NFS client
  Identification information Flavor: AUTH_NULL (0)
  Length: 0

  It seems that the credentials of NFS Client are not correct.  How can I change the flavor of AUTH_UNIX and the UID and GID to 1000?

  Hello VDAEMP,

  As Eddie and Sudarshan has said, the Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the public IT pro TechNet forums below:
  TechNet - Windows Server
   
  Thank you

• I can't install (error says Windows Vista not supported (LR6), I use Windows 7 SP1 worms. 6.1 What is the problem?)

  I can't install (error says Windows Vista not supported (LR6), I use Windows 7 SP1 worms. 6.1 What is the problem?)

  About Vista, but is not https://forums.adobe.com/thread/1836232

• Get this error "The Office does not support the requested protocol display."

  Just built a new environment of view 4.5 and became "The Office does not support the requested protocol display" when trying to use the client to connect through PCOIP, but works very well with RDP... What Miss me?

  Wwill price points righ away.

  When you installed the Agent of 4.5 view you ensure that PCoIP components have been selected?

  -Mike

• Error: Remote connection software does not support network level authentication.

  Original title: REMOTE ACCESS

  I have windows 7 ultimate and the remote connection software supports network level authentication.

  Isn't he supposed to in this version?

  Thank you

  It should be, but there are several remote desktop client updates that came out in the last 6 years as of the optional updates on Windows Update, so I would check that you have all the control panel.

• Satellite Pro L20: Configfree Setup error - system only is not supported

  I tried to update the Configfree with a version more recent on the Toshiba support (for PRO L20 series) site.

  Setup uninstall me the old version and after that it me to say that "the system is not supported.

  How to recover or reinstall my Configfree without using the recovery CD.

  Thank you

  I m wondering if you used the right and compatible ConfigFree Utility.
  It seems you didn t, and so this error message occurred.

  > How to recover or reinstall my Configfree without using the recovery CD.
  I don t think you will be able to reinstall it from the recovery CD without having to install the entire operating system because you will find on the only recovery CD image file. That's why it of not possible to extract individual files, the image of Toshiba programs.

  If you n t want to reinstall the whole OS using the recovery CD, then you can try putting the BONE to this early time by using the System Restore tool.

  Check it out!

  Ciao

• I get an error "the server does not support an SSL connection" with a code of error 0x800CCC7D in Outlook express.

  I followed Bruce Hagen and still cannot send to the OE section. Reception is no problem. When I try to send I got the following error msg: "the server does not support an SSL connection. "Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, server response: ' 250 8BITMIME ', Port: 25, secure (SSL): Yes, Server error: 250, error number: 0x800CCC7D. I tried to change the port for outgoing to 456. When I do so I get this error msg: failed to connect to the server. Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, Port: 456, secure (SSL): Yes, Socket error: 10060, error number: 0x800CCC0E.  Is there a cure for this. He just started two days or at least that's when I noticed I cud not send. If you can help me I will appreciate it more. Thank you.

  JP banks

  Original title: cannot send using OE 6. Reception Ok.

  Hi JPBANKS,

   

  Thanks for keeping us posted and share this information with us.

  Glad to know that the problem is solved. Do not hesitate to contact Microsoft Windows Forums for issues related to Windows in the future.