RESOLVED - "49 error turn off then" HP LaserJet 400 M451dn

Similar Questions

• Service error 49 - Turn Off, then on - LaserJet Pro 200 M276nw

  I was the addition of another post for a different printer but didn't want to Miss anyone with MY printer problem.

  UPDATE * (at least for my LaserJet Pro 200 M276nw)

  I found the cause but will need help from someone at HP to "solve" this one...

  My new guard M276nw throw a 49 Service error, CAT has given a lot of power, voltage on, wait, try again blah blah blah, blah blah fuser problems. 10 minutes from the forum search put me on possible wireless network issues with other printers and the SSID. Anyway after regaining a printer Staples and saw the problem coming up again on a new another brand... I tried the search Forum and Tada! at least I was able to find a cause.

  I have a D - Link DIR-825 wireless router. He has dual band (2.4 GHz and 5 GHz).

  Normally I enabled for the multitude of devices that people have these days in my house.

  I updated the firmware to the last update (20121026) and then restarted.

  Roger restarted shortly after error Service 49.

  Then I disabled the two strips to test each independently wireless band.

  The printer acted normally so I decided allow each band separately.

  When I turn on the 2.4 GHz band in the router, the printer immediately throws an error in Service 49.

  I tested several times (5 to be exact) and every time when the router restarts the printer says error.

  So, I left off 2.4 GHz band and then the 5 GHz band.

  I activated the band 5 GHz 3 times and turned off and found no effect on the printer (at least in a 5 minute window).

  So now I'm left with only a single band wireless router or printer who likes to turn on every 20 minutes or more.

  There is probably a setting (or 2) which can be changed in the router or printer that can prevent this (I hope).

  I just need to find the right person in HP...

  I should have updated this thread I'm sorry, but I found myself updated the same problem on another thread of printer M251nw, since someone has answered that one. I have to keep that one thread - sorry, but it seems to me that I just heard another as well, but for a m475dw as well. Maybe the same problem that I don't know.

  Anyway to update my m276nw situation: After experimenting for a while try to limit I decided to eliminate the possibilities by disabling my router another suggestion of posters to remove the printer from the wireless environment and reset to factory settings. So I turned off my 2.4 GHz band in my router (leaving 5 GHz active), reset the printer and it was sitting still (no reset), he even went to sleep normally. I turned on the 2.4 band and the printer immediately threw the error repeated tent kept the same result no way to leave on the 2.4. The next day so I decided to check my router and found 2 year old firmware. It took several updates to get current and on the last I didn't reset the printer to the factory again and there's no error yet. The printer acted normally for a week, he normally sleeps and wakes. It was turned off (on purpose) a few times and everything seems normal.

  I have not activated wireless again since my house is wired and I could really do without wireless capability, but eventually I want to know.

  My DLink DIR-825 router is still active with both tapes, but using the latest firmware, like the new printer (the other). Is all this took?

  Perhaps.

• "scanner 6 error, turn off then back in market"

  HP LJ300 m375 says error scanner 6, turn off, and then go back' after I scan a document to my computer.

  I stop (and even disconnect) and restarts and it allows me to scan once more and then the error is back and I can't scan again until I turn and turn it back on.

  I don't get this error when I scan to a USB Flash drive.

  How can I get rid of this error?

  Thank you!

  Hello!

  I have something that might work for you.  I'm assuming you want to scan your PC using the HP scanning application.  If this is the case, the default resolution (DPI) is 200.  Try to use 300.  We are still looking, but this seems to work around the problem.

  TLB

  I am an employee of HP

• LJ Pro300 color MFP M375nw. Power cycling, displays "49 service error - turn off the power, then press" on-screen.

  Bike constantly, the power display "49 service error - turn off the power, then press ' on-screen before stopping.
  For this printer only when it is connected to the network. Quite happy to sit quietly when printer NOT connected to the network.

  Unplug the network cable from the printer, check and clear all print queues (there may be a doc pdf sitting in a pc or server print queue)

  Once the queues have been dotted, restart the printer and reconnect the network cable.

  If this does not cure the problem, then the likely problem is a defective formatter Board.

  Good luck!

• WindowXP SP3 turn off then turn on by itself at random.

  WindowXP SP3 turn off then turn on randomly by itself, and sometimes 5 to 10 times a day.
  This problem occurs only recently. PC is 4 years old, no idea to solve this problem?

  Hi AlorAse,

  · This problem occurs when you work with a program or a particular application?

  · Do you remember all the recent changes on the computer before the show?

  Follow the steps listed in the link below: Windows XP Shut Down and auto-restart issues: http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_02may13.mspx

  Also, check if any error codes and error message appears in Event Viewer: how to view and manage the event logs in Event Viewer in Windows XP: http://support.microsoft.com/kb/308427

• MG5300 printer only works now iMac after turning off, then turn it on again

  MG5300 printer only works now iMac or Maclaptop after turning off, then return. Has worked well for a long time, when issue print from a device, the printer icon bounces and messages 'no connection' so stop printer, and then turn it on again and prints. For a few minutes. Next print, have to start all over again. Any thoughts? Thanx.

  Support was terrible. Checked to make sure that files and available wireless network. I had downloaded and installed the drivers. Reset the router and it is up and running again.

  Thank you Canon Support, Jason by name. Well done.

• LaserJet 400 M451dn: laserjet 400

  I have a printer LaserJet 400 M451dn . There was a severe storm, but the printer is on a surge protector APC, including a printer HP LaserJet P1501n and other devices. All other devices operate normally.

  The LaserJet 400 M451dn printer when turned on, the symptoms are the following:

  • Noise of rattling all 4.5 sec
  • White LCD screen
  • no lights on the front panel
  • Ping address responds 'host unreachable '.
  • On printer Ethernet port are turned on

  Printer is on a network, local domestic and no software change or recent driver.

  I tried HP solutions but without success.

  Any suggestion is appreciated.

  ~ Pheeoo

  Hello @Pheeoo

  Think about replacement parts this its go device but you only have two options

  To display sound problem usually a combo that you need to get the trainer + Control Panel from one of the 2 could be the problem

  HP part dept store number its 800 227 8164

  The other option will be to return this printer for a discount for another product

  HP 888 447 0078 ext 813 solutions

  You can call them and see what they have to offer with this second option

• IdeaPad Y530 wireless wifi is turned off then on battery

  I have a new Ideapad Y530 Intel 5100 wifi wireless network card. It works fine when I am connected to an electrical outlet, but when I am on battery it loses connection Wireless after about half an hour of use. When I check the network card, it shows that it is disabled. I'm trying to enable him, but she remains disabled, I can't operate unless I restart the computer. I've done so far that has not fixed it problem:

  1. I checked the power management settings in the device for the network card Manager and you have unchecked the box "allow the computer to turn off the device to save power".

  2. I already uninstalled Readycomm since I had problems with it before

  3. I also affect roaming aggressiveness 1.

  Can someone direct me on how to keep network to get wireless card disabled when I am on battery?

  In addition, once I lose the connection Wireless because the network card is disabled, Windows Vista network settings are really slow to come for me to check my network connection and settings, never had this problem with XP. System seems to hang for several minutes before I can get into the network and sharing Center.

  Thank you.

  I think I've figured this out. I disabled and then uninstalled the power management Lenovo that at first seem to solve the problem but didn't. I knew that it was something to do with power management, so I checked my settings and it was set to energy saving. When I changed to balanced remained turned on the wireless network adapter and I have not lost my network connection. I checked power options advanced for the adapter in symmetric mode and energy-saving wireless and found that Power Saver if it had set for the Maximum energy savings while only balanced if it had set for maximum Performance. The setting for maximum energy savings, it is this that kept disable the wireless card with after several minutes, I changed it to the following configuration, low energy and my without thread remains active and I don't lose my network connection. So for anyone else having problems with the loss of their wireless connection, try to check your power management settings.

• U2715H - Windows automatically resized when the screen turns off then turn it back on

  • Windows 8.1 Pro
  • 1 single monitor connected to the PC
  • native resolution 2650 x 1440 at 60 Hz the value
  • through CDM of the monitor to the RFP the ti EVGA 750 SC (cable Dell)
  • all drivers updated on 28/12/15

  I just bought this monitor and I noticed this strange behavior. Whenever I have turn off the monitor (or it will turn off by itself), if I didn't have a maximized window, all windows (regardless of size) gets automatically resized to fit in the left upper quadrant when the screen turns back on again.  If I had something full screen, this behavior does not occur.

  I find this very annoying. This behavior happened with my previous monitor, which was only 1080 x 1200.

  I was unable to find any setting for the U2715H disable this "feature". This isn't because EasyArrange from Dell. I do not use this feature. And this always happens with Display Manager not installed.

  Is it just a 'feature' of Dell U2715H? Is responsible for Windows? Help, please.

  TIA

  There was no pilot or changes to the hardware of my first post.  BTW, my monitor is a Rev A02.

  A few days after my previous message, another question emerged.  Monitor flash intermittently ON / OFF every few seconds.  I unplugged/replugged the cable CDM - DP and that seems to fix things... until the next day.  This time, I nothing could fix the random rotation power SWITCH of the monitor.  Desperate, I decided to plug an old HDMI cable, I had to hang out.  Flashing problem has been resolved.  Not only this, using HDMI solved my original problem of auto resizing windows.

  The solution to my original problem: use an HDMI cable.  I went to the Dell CDM - DP cable and the problem has been resolved; no more windows resize automatically when the monitor turns off in sleep/towers.  I always get the native resolution at 60 Hz and there is no noticeable disadvantages to the use of the HDMI versus DP interface.  I've been using the HDMI cable for about a week and there is no other issue.

  Just for additional verification, I bought an Accell UltraAV DP - DP 1.2 cable (B142C-007 b-2), one of the few officially approved by VESA (see link below).  Using this cable does NOT my automatic window resizing problem original.  I do not use it long enough to see if they would prevent the random flashing question.

  I still don't know the exact cause of my original question.  I guess it's a driver problem with DisplayPort standard.  But if you do not need DP 1.2 functionality, I suggest that you just use your GPU HDMI output (if she has a).

  www.DisplayPort.org/.../How-to-Choose-a-DisplayPort-Cable-and-not-get-a-Bad-One

• HP Officejet j5780 turn off, then on

  All of a sudden this printer did not finish the trunk upwards. Just to repeat myself "turn the power off, then on. All of the lights on the front flash also. Is he dead?

  Has worked well so far. Have also endorsed two cartridges, left with unplugged power cable and then were. Same problem

  All solutions please

  Thank you

  Found out that if I take the two ink cartridges, then it boots until he tells me put them down. Then it goes down.  Think it might be something to do with this area. There is a lot of excess ink and gunge all around the area of ink. Is it possible to have access to clean here. Is there a routine for this?

  Thank you

• HP5550 68.0 "permanent storage full" followed by "49.4C02 error" "keep turning off & then on."

  End users reported a 49.4C02 error.  They had cycled power on the printer error code and the error code persists.

  I went to the printer to see what was going on.

  I noticed that a few seconds until the 49.4C02 error appeared on the screen of the printer, there was

  a 68,0 error "permanent storage full".

  I tried a cold reboot, but it did not help.

  Could not watch all print jobs in the print as I didn't know what was the address of the network printer.

  The display was frozen on the 49.4c02 error.

  I was unable to print the configuration page to find the IP address / number, so I couldn't determine the printer to look at.

  I found a solution.

  I examined the service manual and found an article on how to initialize the hard disk.

  I expect that this might help as I was getting a storage permanent error 68,0 full, a few seconds before the 49.4C02 error appeared.

  In all cases, it couldn't hurt to try.

  So I power cycle the printer.

  The count of memory at startup, I pressed the MENU button and held it until the 3 LIGHTS all light up.

  I then released the button MENU. I hit the button the arrow (return). The screen of the printer showed a

  INITIALIZE the DISK on the screen.

  I pushed the button tick to accept the initialization process.

  The screen displayed/hidden between a few different views, then on the READY screen appeared.

  Printing all seemed to have disappeared, but at least the printer is online and functional again.

  Not sure how happy the end user who has had a print job in printing, but I was happy to have the operational printer again.

• Oficejet Pro 8600 Plus seems to disconnect and docs does not print unless it is turned off then

  I have a Dell with Windows 7 dekstop. The HP Officejet Pro 8600 Plus is connected wireless and worked well during the past year. The only change of note is that an old belkin wireless router died and was replaced by a new Belkin wireless router which seems to work very well. My Office recognizes the printer and my printer recognizes the router on my desktop

  The problem is that it seems my 8600 turns standby or offline after a certain period of time of inactivity and when print jobs are sent to the printer either by OIOS or by different laptops in the House, nothing prints. My desktop printer that actually tell me job is printing... then it says error, printer offline. However, printer is on and says that it has strong wireless internet at any time

  A single difficulty has been to put off the printer (via button on / off) turn it and then turn it back on and saved then print print jobs. In addition, the new print jobs launched fly right by fine. Then the next day, the problem repeats

  I just unplug printer a surge protector and moved to a wall outlet directly by something else that I read. I use kapersky security system causing no problem before the beginning of the question.

  I have disabled the option to turn on printer for some time and stop at another time to remove this as a cause.

  Dell and Belkin two saying its a HP problem since the printing run after the printer out of power, and then power on, but I am running out of ideas to try to stop.

  Bill O'Connor

  These settings are to set up your wireless printer to stay connected to your router, wireless devices stay better connected and makes your router secure and hack proof.

  1. define a static in the printer IP address (click here) out of the DHCP of the router Beach (check your manual).

  It is for Linksys routers, but can be used for all routers. Check your DHCP range and change this

  first of all if necessary. More Help Wireless Printing is here (Windows solution 4, static IP).

  2. check the printer "Auto Off" is disabled.  Use the built-in webserver (EWS) by going in the

  the printers IP address in your browser's address bar, click Settings tab/Auto Off. Or use the printer

  Assistant, printer Home Page (EWS).

  3. If the printer supports and has IPv6 enabled, disable the IPv6 option in the printer.

  4. If necessary and you have assigned a static IP address, try using 8.8.8.8 for the preferred DNS server and

  8.8.4.4 at the level of the auxiliary DNS server.

  In the router: (refer to the manual of your router for more information)

  5. use a wireless channel fixed as 1, 6 or 11, never 'auto', try channel 1 first then the rest.

  6 choose the router to 20 Mhz only, or 145Mbps router function.

  7. always use WPA2-AES encryption (personal), but you can try the "mixed" mode

  8 disable the WPS and never use it and disable the UPnP for the security of routers. No one can hack into your

  now the system and helps with wireless connectivity (if you want to know why, research on the web).

  9. If you have a router dual band (2.4 Ghz and 5.0 Ghz bands), make sure you the SSID is NOT the same.

  they must be different for all the bands, even for networks without comments.

  10 broadcast SSID must be enabled.

  11. save all settings. Food at the same time, wait 2 minutes.  Power on router wait 2 minutes.

  12 turn on the printer and check that it reconnects to the router.

  Windows 7/8/8.1 is discovered the system on or off?

  1. Control Panel/Network and Internet/network and sharing Center / advanced sharing settings.
  2. Under home or work (current profile) / network discovery.
  3. Select "Turn on network discovery" and save the changes.

• iPhone 5 c screen went black with 78% battery. Tried turning off then without result.  The phone felt warm to the touch.  Is - fixable?

  The screen on my IPHONE 5 c became black and does not.  Before that I tried to send a text without response, battery was 78%.  I tried to turn on/off again without result. Any suggestions?

  Hello carolfromlincoln!

  Thank you for joining the communities Support from Apple! You might want to try the steps in this article: If your iPhone, iPad or iPod touch does not illuminate if these steps do not work:

  Contact Apple support to set up the service if you have any of these problems:

  • You always see a black screen after loading, reboot of the force or following the steps described in this article.
  • You see a black screen, but he can hear the alerts, the sounds and vibrations.
  • Your screen is enabled, but it does not respond to the when you tap, slide or try other gestures.
  • You cannot force your device restart because your Home button or the sleep/wake button is broken or blocked.
  • Your device is stuck on the Apple logo, displayed a solid color, or is not recognized in iTunes.

  See you soon!

• my habit of portable full process of start-up ever since I made the last update to El Capitan, gets hung up on where the Office should appear.  Behavior strange screen turns off then flashes every 8 seconds or so still visible status bar

  When this happens, you can also see a white spinning dial when the screen is flashing.  But the Bureau just never came up.  Tried the disk first aid in safemode, LANDAU of compensation running.  Now I can't even on it to open it in safe mode.   I also tried to install a new copy of El Capitan in safemode, but she got too successful for the download.   I have a macbook pro mid-2012 can't remember the speed of the processor, 16 MB of RAM.

  I suggest the following:

  Try each of them in order. A test to see if the computer works properly:

  1. Reset the PRAM
  2. Reset the controller (SMC) system management
  3. Start the computer in Safe Mode, and then restart normally. It's slower than a standard home.
  4. Repair the disk by booting to the HD recovery immediately after that the chime press the command and R keys until the Utility Menu appears. Choose disk utility and click on the continue button. Select the withdrawal (usually Macintosh HD) volume entry in the list to one side.  Click first aid button in the toolbar. Wait the fact button appear. Disk utility and return in the Utility Menu. Restart the computer from the Apple Menu.
  5. Reinstall OS X by booting from the Recovery HD using the command and R keys. When the Utility Menu appears, select reinstall OS X and then click on the continue button.
  6. Download and install the update of OS X El Capitan 10.11.6 Combo

• iPhone 6 s screen turns off then gets normal back in 10-15 minutes.

  Hello everyone. I bought my iPhone 6 s 64 GB gray space to the end of December 2015. It came with Samsung A9 processor. For the last 3 months, it began to close its screen down randomly at least 1 time in 2 days. I think it has something to with the LCD backlight because the touch screen works on completely black screen. I can still receive calls by remembering where to touch. Then on an average of 10 minutes, it returns to normal. Is anyone else having this problem? Or suggestions? Thanks in advance.

  (Incidentally opening and closing or restarting with power and button "home" at the same time does not.) Whatever you do, screen becomes normal when he wants. I tried hard reset, formatting and relief, but the problem is still there.)

  Note: probably a coincidence, but it never happened before iOS 9.3

  Hi AnilOzbek,

  Welcome to the communities of Apple Support! I'm sorry to hear that you are having these problems with your iPhone. If you continue to have problems with the display or the backlight, you can find the troubleshooting steps described in the following article useful, up to and including communicating directly with the Apple Support:

  Get help with the screen on your iPhone, iPad or iPod touch - Apple Support

  Concerning