Restart slideshow from the beginning

I just bought a DPF-VR100. When it is disabled, then it seems to restart the slideshow, everywhere where he stopped the last time. I want to start from the beginning each time. How do I do that? I couldn't find this setting or all instructions in the manual. I have the photos and music in the memory. The photos are classified in the index of the way I want them to appear.
Thank you!

Hello and welcome to the forums.
This is a normal operation. If you turn on the photo frame off the power during the slide show and back, the slideshow restarts from the last image read. Unfortunately there is no adjustment for the slide show restarts automatically after the next power on.

Tags: Sony Products

Similar Questions

  • can I restart my mac - pro to start from the beginning I / ve he had only 2 days and I think that I / ve screwed it up

    can I restart my mac pro from the beginning.i/ve really messed it .i/ve only had 2 days.thanks

    A new Mac comes with 90 days of free technical support, AppleCare.

    Please call AppleCare.

    AppleCare: 1-800-275-2273

  • Xp pro installation gets past the copied installation files and then restarts, rather than continue with install it starts from the beginning again.

    new installation of XP pro on a Dell Inspiron mini

    Xp pro installation went copied files Setup then restarts, rather than continue with an install it starts from the beginning again, laptop is configured to boot from the hd, but does not do that, I reset bios to default and hd settings has been reformatted, the cd for this laptop drive is usb because it has not built in 1... If I try and I remove the usb cd when reboots after copid setup files it told her there is no operating system...

    any help much appreciated...

    Hi, Leon,

    Always include computer make and model, please.  Thank you.

    Research in the Bios (reboot and press F1 or F2 depending on your system, check that all usb options are enabled (for example, USB legacy or support for USB 2.0 devices).)

    If there is a timeout parameter, set it to Max.

    Then, find the boot device priority section

    A USB flash drive, which is usually listed as USB - HDD, but may be listed as a removable device, will have a priority very low start.

    Rearrange the boot device priority so that the flash drive has a higher priority than the hard drive.

    Install Windows XP from USB key

    • Insert the USB key into the USB port on the computer.

    • Open the "I386" folder and find the file "Winnt.exe".

    Double-click on the "Winnt.exe" to launch a command prompt BACK to an installation of Windows XP.

    Type the path of the location of your "I386" folder in the DOS window. For example, if your USB is the letter "D" in your "My Computer" window, type "d:\i386" without the quotes and press the Enter"" key.

    Let the installation program copy the Windows XP installation files on your computer.

    Restart your computer to a command prompt. The Windows XP Setup will continue automatically.

    Follow the on-screen instructions to complete the installation. The program will ask you your Windows XP product key in this process.

    http://www.ehow.com/how_6912418_install-Windows-XP-USB-drive.html

    Make a bootable memory card or USB key using PEBuilder

    http://www.tech-recipes.com/Rx/2583/making_a_usb_drive_or_memory_card_bootable_using_pebuilder/

  • Doesn't have installation of Vista updates. He continues to try set up the third update with 0% completion and then it turns off and start again from the beginning. Keep in the loop... Help! There is no error message.

    As above. He is not in windows more simply the third update installation and then turns off computer and restart new since the beginning. Tried running safe mode but without success

    Restore point:

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

     

    If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

    Download the ISO on the link provided and make a record of repair time it starts.

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

    When you have changed that, insert the Bootable disk you did in the drive and reboot.

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    Link above shows what the process looks like and a manual, it load the repair options.

    NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

    Read all the info on the website on how to create and use it.

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

    It's a very good Vista startup repair disk.

    You can do a system restart tool, system, etc it restore.

    It is NOT a disc of resettlement.

    And the 32-bit is what normally comes on a computer, unless 64-bit.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    If the above does not resolve the problem:

    Windows Update Forum:

    It comes with Vista, upgrade install and activate Forum.

    You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

    http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

    When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

    In this way, you will receive the best help.

    See you soon.

    Mick Murphy - Microsoft partner

  • Hello! How can I resume my apps purchased after a break... or do I need to download from the beginning... If so, how?

    Hello! My purchased apps (logic pro x) will not resume downloading after a break. Do I need to download it from the beginning?  If so, how?  I tried to resume the download, but the resume icon does not... I also tried to download from the start by removing apps half downloaded from my pc...  I m running os 10.10.5 yosemite. Any suggestions will be much appreciated.

    Hello there, im khans.

    Looks like you are unable to download the application Logic Pro X on your Mac under Mac OS X Yosemite. The following article contains some great instructions on how to reinstall Logic Pro X:

    Logic Pro X: Troubleshooting basics

    11 reinstall Logic Pro X

    Another approach you might consider is reinstalling Logic Pro X. To do this, you must remove the application and then reinstall it. You don't have to remove everything that was installed with Logic Pro X.

    To reinstall Logic Pro X, follow these steps:

    1. In the Finder, choose Applications from the menu reach.
    2. Locate the application Logic Pro X and drag it to the trash.
    3. Open the Mac App Store
    4. Click the Purchases button in the toolbar of the Mac App Store.
    5. Connect to the Mac App Store using the Apple ID you first used to buy Logic Pro X.
    6. Look for Logic Pro X in the list of applications purchased from the App Store. If you do not see Logic Pro X in the list, make sure that it is not hidden. See Mac App Store: hiding and showing buys for more information.
    7. Click on install to download and install X Pro Logic.

    To learn more

    For more information on settings or installation, please refer to the X Logic Pro User Guide.

    For any question, install the additional content, see Logic Pro X, MainStage 3: additional content installation issues.

    Thank you for reaching out to the communities of Apple Support.

    Kind regards.

  • I accidentally deleted all my settings and the apple iphone 6 s ID. Now I have to activate my phone and start from the beginning. But I don't have my EA sim with me right now and cannot organize any sim EE. How can I activate my phone without sim card?

    I accidentally deleted all my settings and the apple iphone 6 s ID. Now I have to activate my phone and start from the beginning. But I don't have my EA sim with me right now and cannot organize any sim EE. How can I activate my phone without sim card?

    Sorry, but you can't activate an iPhone without a SIM card installed. It is simply not possible to do.

  • How to read from the beginning to reference trigger?

    Hello!

    I develop a system a little on a NI DAQmx 6025 and want to know how can I get data from an early relaxation of reference.

    I use "AcqVoltageSamples_IntClkDigStartAndRef.2008" to control the unit in c#

    If I set up the Starttrigger only, I can trigger... (the measure is to start by climbing aboard PFI0)

    ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    myTask.AIChannels.CreateVoltageChannel (physicalChannelComboBox.Text,"", (AITerminalConfiguration)(-1), rangeMin, rangeMax, AIVoltageUnits.Volts ");

    myTask.Timing.ConfigureSampleClock ("", sampleRate, SampleClockActiveEdge.Rising, SampleQuantityMode.FiniteSamples, 1000);

    myTask.Triggers.StartTrigger.ConfigureDigitalEdgeTrigger ("/ PFI0/Dev1", DigitalEdgeStartTriggerEdge.Rising);

    Reader = new AnalogMultiChannelReader (myTask.Stream);

    ...

    drive. SynchronizeCallbacks = true;

    drive. BeginReadWaveform (-1, New AsyncCallback (myCallback), null);

    ... MyCallback...

    data = reader. EndReadWaveform (ar);

    ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    Now, I want to stop my measurement by the trigger of the reference, so I set up the Referencetrigger on the same source (PFI0)

    myTask.Triggers.ReferenceTrigger.ConfigureDigitalEdgeTrigger ("/ PFI0/Dev1", DigitalEdgeReferenceTriggerEdge.Falling, 10);

    (This line is after the configuration StartTrigger)

    If I start the task and give the triggersignal, the measurement starts. But now the measure must stop if I start PFI0 again!

    I don't know what I have to do to become a measure from the beginning to trigger Stop... I mean PFI0 PFI0 rising Edge edge

    Thanks for the support!

    Suchen für alle die noch immer nach einer Antwort, ich habs jetz!

    For all who are looking for this answer, I get it now!

    --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    myTask = new Task ("aiTask");        Create a new task
    Initialize local Variables
    Double sampleRate = Convert.ToDouble (rateNumeric.Value);
    Double rangeMin = Convert.ToDouble (minimumValueNumeric.Value);
    rangeMax double = Convert.ToDouble (maximumValueNumeric.Value);
    Create a virtual channel
    myTask.AIChannels.CreateVoltageChannel (physicalChannelComboBox.Text, "", (AITerminalConfiguration)(-1),
    rangeMin, rangeMax, AIVoltageUnits.Volts);
    Set up sync Specs
    myTask.Timing.ConfigureSampleClock ("", sampleRate, SampleClockActiveEdge.Rising, SampleQuantityMode.FiniteSamples, 1000);
                
    Configure start and reference triggers
    myTask.Triggers.StartTrigger.ConfigureDigitalEdgeTrigger ("/ PFI0/Dev1", DigitalEdgeStartTriggerEdge.Rising);
    myTask.Triggers.ReferenceTrigger.ConfigureDigitalEdgeTrigger ("/ PFI0/Dev1", DigitalEdgeReferenceTriggerEdge.Rising, 100);

    Check the task
    myTask.Control (TaskAction.Verify);
    Create the object reader
    Reader = new AnalogMultiChannelReader (myTask.Stream);
    Start the task, and set the playback position
    myTask.Start ();
    myTask.Stream.ReadRelativeTo = ReadRelativeTo.CurrentReadPosition;

    AnalogWaveform[temp];

    {while(!myTask.IsDone)}
    Temp = reader. ReadWaveform (60000);
    }

    myTask.Dispose ();

    --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    Mit dieser Lösung kann man von mension zu messen mension.

    With this resolve you can measure from edge to edge.

  • audio is launched from the beginning of the song little matter where I click in the movie timeline to start playing?

    I need the audio to help the photo calendar synchronization. However, no matter where I start playback to check a second time when a certain image, audio ALWAYS starts again from the beginning of the song! How can I stop this?

    Since you have posted in a forum XP... I'm guessing that you're
    using Movie Maker 2.1?

    If you drag the playback indicator (vertical line with square
    at the top... Rest the pointer on the square and drag)...
    the music should start playuing.

    Unlike the video track... you can click left/make dragging clips
    the audio left and right. And you can change the
    duration of a single photo on the timeline manually. Move
    your pointer autour in border of an element until you see a
    double red arrow. Now drag the double red arrow... you'll
    display a ToolTip that shows the evolution of life.

    Articles that offer information about audio sync with the video

    "Collections of projects".
    http://www.Papajohn.org/newsletters/024-Collections.html

    Study the rendering of DV - AVI files
    http://www.Papajohn.org/newsletters/048-StudyDV.html

    Editing film 'Basics '.
    http://www.Papajohn.org/newsletters/139-EditingBasics.html

  • So why make a movie in movie maker, the only way to get the song to play with the photos in sequence is in play from the beginning?

    I am trying to edit photos to last for some parts of the songs (fade in and out where I want to that they), but the only way to see what the photos of 'falling' in the song by playing the song from the beginning. Every time. It won't let me go to a certain section of the timeline and play both the photo and the song at that time here (it takes me to the photo, but he began to play the song in some random place)?

    Thank you very much!! =)

    Hello

    Once you have added music, go to the Options tab. Now click on Split (in fact the split music) you should see the music bar along the top of the film split.

     

    Audio setting in Windows Movie Maker: frequently asked questions (valid also for Windows XP)

    http://Windows.Microsoft.com/en-us/Windows-Vista/adjusting-audio-in-Windows-Movie-Maker-frequently-asked-questions

    See also: http://windows.microsoft.com/en-US/windows-xp/help/movie-maker/faq

  • How can I get rid of the icon "shut down windows"? It appears from the beginning to the top!

    How can I get rid of the icon "shut down windows"? It appears from the beginning to the top!

    Hello jsitch,

    This thread has been created in the forum Desktop and personalization; the Microsoft moderation team has moved this thread to the Performance and maintenance Forum.

  • Windows Mail has disappeared from the beginning

    All places start with the new computer and Windows 8, as a people, mail, calendar, news disappear from the beginning.  How do I get back?

    Hello

    I suggest you to follow the steps below and check if it helps.

    Before we try to fix this problem, please answer the question below.

    (1) remember you to make changes prior to this problem?

    I suggest you follow the steps below and check if you are able to get the apps to the start screen.

    (a) press the Windows key + Q, type Mail app

    (b) right-click on the mail application, and select PIN to start.

    Similarly, follow the same procedure to bring applications that do not appear in the start screen.

    If you are unable to find the applications, try to download from the app store for Windows.

    (a) open Windows app store.

    (b) press the Windows key + C,

    (c) select search and type Mail app

    (d) select Mail, calendar, people, and e-mail, and then click on install.

    Follow the instructions to install the other missing apps.

    See also the articles below.

    Customize the splash screen

    http://Windows.Microsoft.com/en-us/Windows-8/start-screen#1TC=T1

    What happened to the apps on my PC?

    http://Windows.Microsoft.com/en-us/Windows-8/what-happened-apps-PC

    Hope that the information has been useful, if you have any additional questions or questions about Windows, feel free to post. We will be happy to help you.

  • Game sounds from the beginning to the place where I am in the timeline panel

    I am currently lipsync animation. I have the sound flow value instead of the event, but for some reason any (often, but not always) when I play the part of the sound, no matter where I am on the timeline, the sound is played from the beginning as if I started at the beginning of the melody. I tried to split the file between each syllable, and that seems to have fixed, but now there is a strange noise that plays to each division, so that the method is not really practical.

    I have a feeling that this may be a RAM issue since it seems to have no known cause and nothing seems to fix it for sure. It seems like something that would be caused by the release of maxing out the RAM. I have 6 GB and I thought that would be enough, but it may not be. There isn't really a lot going on in this animation that could bring it to use this amount of RAM, but after reading about how it works the Stream parameter, looks like a cumbersome process RAM.

    What do you think guys? It's something I've missed, or it's just my RAM and I'll have to deal with it, unless I get more?

    Update: I checked my task during execution of the animation Manager, and it goes up to 60% at the most. I'm puzzled.

    It is a known problem that can occur in Windows. It's already been fixed, but I don't know when the update will be available. 'Early 2016' is say Adobe.

  • How to create e-commerce site using adobe muse from the beginning to the end, please

    How to create e-commerce site using adobe muse from the beginning to the end, please

    Mylenium, why comment you on the forums of Muse? I've never seen a useful comment on these forums. You seem to just upset against Muse all the time.

    in any case, definitely go with widgets Ecwid and J-26. They are the best.

  • Music / sound plays from the beginning

    I'm starting a new Flash animation (I've not used the Flash in a few months, but it says it is updated), and for some reason, I've added music, will only play if I start from the beginning of the timeline. If I start from anywhere in the middle of the timeline, after the departure, the sound is not reading at all. What is going on? Can it be fixed?

    What you describe would be the case if you have defined a test of properties. Change that to the stream.

  • You can change a song somewhere in the Middle rather than start from the beginning?

    You can change a song somewhere in the Middle rather than start from the beginning?

    Hello Gene,

    Currently, there isn't a way to do. It's a great idea and we will certainly look at it later!

    Thank you

    Bronwyn

    Community Manager for first Clip

Maybe you are looking for