restore the configuration of the cisco ACS 1121 ver 5.2 to SNS 3425 ver 5.6

Similar Questions

• Version of Cisco ACS 1121 5.3 - logging

  Hello

  I am new to Cisco ACS 5.X. What I've read, the Cisco ACS can act as a logging server. Does this mean, all messages from syslog to all other network and ACS devices can be stored by ACS? I'm a little confused on that part.

  Finally, I understand that Cisco ACS has many or perhaps 2 instances? When we use these instance? What is this instance?

  Kind regards

  RAM

  In the deployment, you must specify an acs as the Logcollector server. All other servers send the logs to the Logcollecter.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_sys...

  In a distributed deployment, each acs server is an instance. If you have a main instance and multiple secondary instances.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_sys...

  Sent by Cisco Support technique iPad App

• Configuration of the Cisco ACS Radius

  Hello

  I'm trying to set up authentication radius on cisco ACS but short question. When I set up my group of network devices in the configuration of the AAA Client as one of ray device groups, my authentications fail with authentication as a failure code"

  CS invalid password' but when I change my group of devices to "Unassigned", everything started working.

  On my AAA client, when authentication fail, I see

  Server RADIUS audit package fails:

  Please note that the AAA client is a non-cisco device.

  Any suggestions?

  It seems that you run ACS 4.x. You are facing this problem because the key is set on the excessive rides of the level (Group of devices network XYZ in your case) NDG key at the level of the AAA client.  Please make sure that you don't have different secret key on the client inside the NDG AAA and on the NDG himself.

  Not affected is working because it has no key defined in the NDG.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/NetCfg.html#wp342738

  "Each device that is assigned to the network device group will use the shared key you enter here. The key that has been attributed to the device when it has been added to the system is ignored. If the Enter key is null, the key of the AAA client is used. »

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500.

  We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups.  It works, but it works too well.

  We have a group called XXX we need to have access to the Cisco AnyConnect Client.  We have selected this group of our Active Directory and added to our ACS configuration.  We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN.

  We added XXX movies for the elements of the policy of access to the network-> authorization profiles.  We also have a profile of YYY.

  She continues to knock on our default Service rule that says allow all.

  We have also created a default network access rule. for this.

  I am at a loss.  I'm sure I missed a checkbox or something.

  Any help would be really appreciated.

  Dwane

  We use Protocol Management GANYMEDE ASA and Ray for VPN access?

  For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too.

  On the SAA, you must configure Ganymede and Ray both as a server group.

  For the administration, you can set Ganymede as an external authentication under orders aaa Server

  AAA-server protocol Ganymede GANYMEDE +.

  Console HTTP authentication AAA GANYMEDE

  Console Telnet AAA authentication RADIUS LOCAL

  authentication AAA ssh console LOCAL GANYMEDE

  Console to enable AAA authentication RADIUS LOCAL

  For VPN, you must set the authentication radius under the tunnel-group.

  I hope this helps.

  Kind regards

  Jousset

  The rate of useful messages-

• How to restore the password on Cisco ACS 5.4

  Hello!

  Try to restore the Cisco ACS 5.4 password installed on vmware. Where can I get the password recovery DVDs? There is no software in the list on the site.

  TAC may provide to you. You will need to open a folder and the application.

  HTH

• Cisco ACS 4.2: The most important to back up files?

  Dear Sir

  Can you tell me what are the most important files to back up in the Cisco ACS directory?

  Currently, I am only backup (with Symantec Backup Exec):

  C:\Program Files\CiscoSecure ACS v4.2\CSAuth\System backups

  * But, I would like to know if my server crash, can I restore the entire configuration with the files listed in the directory below? (Users, groups, groups of devices, AD, mapping, users, groups,...)

  * The Cisco ACS there change in the Windows registry?

  * Is it necessary to reinstall the Cisco ACS, if I need to put in an emergency on a new server? I guess Yes, because the installation creates services, etc.

  I ask this question because it takes time to install the patches...

  * Or, can I save all the Cisco ACS directory... On a new server, install the Cisco ACS and restore the backup?

  Thank you very much for giving me your experience about it.

  Kind regards

  You should back up the files that come from ACS backups, i.e.

  System configuration > backup GBA, the location that is specified in this section.

  And the default location is the one that already save for example "C:\Program Files\CiscoSecure ACS v4.2\CSAuth\System backups"

  In case you are required to host ACS on a new server, you would be required to re - install the complete application of the CSA and then simply take the last backup and restore in the newly installed ACS. It will be to restore everything users, group etc. to etc. of the external database mappings.

  When you install ACS on a new server, then make sure that if you run them Services ACS with a service account (this is required for the authentication of the window according to your requirement), you would be required to run new services with this account too, and which may require that go you through the following documentation.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/Windows/postin.html#wp1041202

  Kind regards

  Prem

  Please rate if this can help!

• Selection rule for the 5.2 Cisco ACS Service

  Hello dear,

  I'm trying to configure the Cisco ACS 5.2 to Dot1x of authentication for clients on windows 7 & windows XP, I did all the steps but I could not create Service rule, it gives me an error message that you can see in the attached screenshot.

  After that I specify the allowed protocols it gives me the choice to choose the choice of identity and the is ' t it give me this error.

  your help is very appreciated.

  Kind regards

  Ibrahim

  Try another browser like Hussam suggested and let us know the results.

  I updated FireFox to 15.0.1 and now I am not able to manipulate many parameters with ACS 5.3
  Version of this browser is extremely stupid with ACS 5.x, but it shows not all message boxes. It just does not display the page when you click on the link.

  If different browsers show the same question, I would say that you restart the machine (physical or virtual) completely and try again.

  It is also best to upgrade to the latest patch, if this is not already the case.

  Greetings,

  Amjad

  Rating of useful answers is more useful to say "thank you".

• Cisco ACS and the domain controller

  Hello

  We are currently using the Cisco ACS 3.2.3.11 solution engine and using a Windows domain as a remote agent controller.

  We now have the ACS to 4.1

  1. do I need to upgrade the remote agent on the domain controller as well?

  2. any computer on the network can be used as a Distribution Server?

  3. after an initial backup and upgrade then to 3.3.3.3 I make another backup before the upgrade to 4.1?

  You can use any PC in the network as a Distribution Server.

• How can I use Cisco ACS to save Shell commands

  Hi guys, pleeeease how can I configure Cisco ACS to do command authorization on my Cisco 3660 router. I get the accounting logs and authentication but no newspaper that show orders issued by users - shell and it's the most important paper that I need. I read materails and download articles on the site of Cisco... but the thing is still does not give me the papers.

  I have these lines on my router:

  ...

  AAA authorization config-commands

  AAA authorization exec default group Ganymede +.

  AAA authorization commands 15 default authenticated if

  AAA authorization network default group Ganymede +.

  ...

  It's funny, when I turn on debugging of the authorization of the AAA on the router, it shows me every command being sent by the user on the debug log. But nothing shows under Administration TACAC + on the Cisco Secure ACS. What is responsible for this?

  *****************************************************

  I installed the trial version of the Cisco ACS 90 days and made all necessary settings and I have to say I like what I see already. I'm opening moves to recommend the product to purchase. Thank you guys, I got about the features of this ACS software through this forum, keep up the good work. I recommend the software for those who need to have adapted to the management reports Security Audit logs.

  If I understand what you're asking correctly, the answer is not in the authorization, that it is in accounting. I set up on my routers and send to ACS orders that level 15 privilege users enter on the router.

  orders accounting AAA 15 by default start-stop Ganymede group.

• RADIUS does not not on Cisco ACS SE v4.1 (1)

  Hello

  I have a CiscoSecure ACS version 4.1 (1) build 23.

  I can't configure the Cisco ACS for granular control of access router. I have a Netopia Router that is configured to use RADIUS to authenticate remotely for a telnet connection. The router sends the request to access the Cisco ACS SE RADIUS and a sniff on the side of the ACS shows the application of GBA, but I see no response from the ACS. RADIUS authentication to work with a Windows 2003 server.

  I configured an AAA client and a user of the ACS and use the default group. I use IETF RADIUS. Should what attributes I configure. In Windows, I use Service Type framed and Framed-Protocol PPP. This does not work with the Cisco ACS SE. Nothing shows up in the newspapers. It shouldn't be so difficult, but for some reason I can't make it work.

  Thanks for any help.

  Jutta Kullmann

  Jutta,

  Good to know it works very well. Please mark this thread as solved so other can benefit from.

  Kind regards

  ~ JG

• Cisco ACS 5.2 VMware 'Management' process hangs

  Hello

  We recently purchased the Cisco ACS 5.2 VMware must be installed on VMware ESXi 4.1.  However, after commissioning the virtual machine with the requirements set out in the Cisco installation guide, GBA is unable to start properly.

  We don't get messages visible error, but when checking on the process of the CSA, I see that the process of 'management' is suspended in the "initializing" State

  Any ideas how to solve this problem?

  Thank you

  Gilbert

  ESX 4.1 is not supported with ACS 5.1

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/device_support/sdt52.html#wp75825

  Virtual Machine requirements

  The minimum configuration for the virtual machine must be similar to the hardware configuration of the server series CSACS-1120.

  Table 6-1 lists the minimum system requirements to install ACS 5.2 on a VMware virtual machine.

  Table 6-1. minimum system requirements

  Type of requirement	Minimum requirements
  CENTRAL PROCESSING UNIT	Intel Core2; 2.13 GHz
  Memory	4 GB OF RAM
  Hard drives	500 GB of disk storage
  NIC	1 GB NETWORK interface
  Hypervisor	VMware ESX 3.5 or 4.0

  Installation of ACS 5.2 on VMware

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/installation/guide/csacs_vmware.html#wp1057864

  Kind regards

  Jousset

• Cisco ACS 5.2 and IOS XR

  We deploy devices with IOS XR and I was wondering if anyone has experience their deployment with GANYMEDE authenticate on the Cisco ACS 5.x platform. If so, can you give some examples of how you have mapped the groups predefined by the user.

  Thank you

  Here's an example of how to do that crs to ensure share you the correct tasks under the profile of the shell.

  http://www.Cisco.com/en/us/docs/routers/CRS/software/crs_r4.1/Security/Configuration/Guide/syssec_cg41crs_chapter1.html

  http://www.Cisco.com/en/us/docs/routers/CRS/software/crs_r4.1/Security/Configuration/Guide/syssec_cg41crs_chapter1.html#con_1185183

  Thank you

  Tarik

• ACS 1121 with v5.0 lost PAK

  A customer bought a Cisco ACS 1121, it for more than a year. He was then unpacked and the PAK is lost, no. where to find them.

  Is it possible to recover the lost PAK? Need help very much.

  You can send an email to [email protected] / * / with the following information:

  Cisco sales order number

  Contract SAS

  You can get your license of software on this site: http://www.cisco.com/go/license. Once on this site, you will need to enter your Cisco.com user ID and your password to access this site. You will also need to enter your product key for authorization (PAK).

  Kind regards

  Jousset

  The rate of useful messages-

• Cisco ACS 5.6

  Hello

  I wonder if anyone can help me? Our server team recently installed the Cisco ACS (version 5.6) on a VM server. I can connect to the Web GUI OK account using the account ACSAdmin. The team of the server informed me that they scheduled the same password for the CLI admin account as they did on behalf of GUI ACSAdmin, but I get "access denied" when I try to SSH to the server (with the username admin).

  I looked at different messages and documentation, but it seems to me that the CLI SSH account can be managed via the Web UI?

  Does anyone know a way to hack the account SSH, or should I just ask the server to be rebuilt? I can see some tips of password recovery, but this seems to apply to a physical server not a VM.

  Thank you very much

  Hello

  Boot from iso GBA 5.6 and reset the console password

  Thank you

  John

• Does Cisco ACS 1113 v4.2 device work with Windows 2008

  Hello

  I have a wireless currently in production infrastructure. All my Cisco LWAP is managed by Cisco WLC. Authentication is done via RADIUS through my device Cisco ACS 1113 running on version 4.2. The Cisco ACS 1113 device communicates with my Windows 2003 Active Directory. Everything is good now.

  Next month, we plan to update Active Directory from Windows 2003 to Windows 2008? Will be all fine and good, or will it be questions? Please advice kindly.

  I saw another post in this community that the States https://supportforums.cisco.com/thread/1003597?tstart=0. I am now confused. Help, please.

  Kind regards

  RAM

  + 60122918870

  ACS 4.2 does not work with Windows 2008R2.  I had a case of TAC open about this, and basically, they told me that I had to switch to 5.2 ACS.   I've been doing demonstrations there and it authenticates with Windows2008R2 very well.