robot speed

Speed of the processor of my pc is 2.2GZ, but it runs at 1.2 GZ. What are the possible causes and remedies

DCampbell1980 wrote:

Install the CPU - Z (google it) and watch the speed of the CPU. Now to run software that will be the task of the system (Prime95 will do exactly that) and watch your CPU speed in CPU - Z.  Speed of processor in modern systems are modular, which means that they can reduce their clock speed to save power. For example if you're just looking at some web pages or typing a document, there is really no need to be clocked at 2 GHz.  If the speed of your system shows full speed when running Prime95 then your system does its job very well.

This scaling, occurs when a system is running too hot is to say. remove the system clock to reach lower temperatures.  It would be worth Googling your system to find out what are the normal temperatures then check those against temperatures of your system. Leave a margin of error as far as temperatures go. A system running at the Morocco is likely to run a tad more hot than a performer in Alaska, but they will be close.  If your temperature is high, it would be interesting to maintain regular, clean the fans, re - stick the CPU/GPU, etc.

Good luck

DCampbell

. I am better informed now, thanks for the advice.

Tags: Notebooks

Similar Questions

  • Satellite Pro 6100: Intel Pentium 4 M clocked 0.2 Mhz instead of 1.8 MhZ clock speed

    Hello

    I have a 6100 Pro Satellite under XP SP2 on Bios 1.90. A few days ago, he suddenly started running very slowly.
    According to the value of the ID of Intel, processor running at approximately 0.2 MHz, instead of the maximum speed of 1.8 MHz, with a similar reduction in the speed of the bus.
    I have reset the BIOS and restore the MBR & OS, but the problem remains.

    I'm running on current alternative, with display 100% charged battery. I also turned off all power settings to try to stop the running slow robot through the Intel speedstep technology.

    This might sound like a hardware problem, but if I boot the machine from a Linux CD (Knoppix), it works very well - very reactive, and according to linux, the clock measures the speed to about 1.79 MHz.

    Does anyone has an idea what could be causing this, or what I can try next?

    Hello

    at first your machine cannot operate at 0.2 Mhz. It's impossible! So I think that this utility Intel ID is not give you correct information. He must know that the slower speed will achieve your cpu, established in the region of 600 mhz.
    With 0.2 Mhz run your computer won´t!
    You said that you have restored your system, but the fact that you have installed the latest drivers and tools for this computer from the Web from Toshiba site?

    Maybe your CPU is defective, which can be a reason.

    Welcome them

  • DaNI robot control

    Dear all,

    I robot 2 DaNI and I'm doing the robot to read a text file that contains the speed profile.

    When I use the labview to read the file no problem and I can read the values easily.

    The problem is that the robot can not read the text file, when I run the program on the robot, I get an error message the file does not exist.

    Note: the file is on my desk.

    I think I have to upload the text file to the robot, but I do not know how?

    Please if any body can help me with this I appreciate really.

    Best regards

    Hello Zhang,

    When you move the file to the sbRIO target you should be able to select a folder in the hierarchy.  The root directory is "c:\". "when you use a LabVIEW code path.  I suggest you put your file path somewhere under the folder "c:\ni-rt\LabVIEW Data\".  In this way, you can use the constant in the default data directory to get the path of this folder in your VI.

    The sbRIO address can be found in MAX.  When you select the target RT under "Remote systems" the IP address appears in the "System Settings" tab.  The IP address must also appear in the tree view of the LabVIEW project next to the name of the target of robot.

    Chris M

  • This module requires a Lynxmotion AL5A robotic using LabVIEW arm control

    Hello world

    I'm a little confused about what NI LabVIEW toolkits to be used in order for me to program the arm Lynxmotion robotic. Somebody has arms lynxmotion robot programming experience using labview? What should be awared by selecting the correct tool boxes. Do I need to have the tools of design and simulation of control? What about embedded design modules? Please help me.

    Thank you

    Hi DK,.

    The Module digital output NI9474 high-speed Sourcing should be more than enough.

    In fact, we have a demo of work available by using the AL5D and NI CompactRIO. The concept should always be the same property.

    Best regards

    The Ilana Joshua

    Technical sales engineer

    NEITHER ASEAN

  • Numerical integration of acceleration and speed

    I control a differential robot mounted by two motors. I use encoders to detect the movement of the robot. I kinematic equations for the linear and angular speed of the robot using wheel from coders speed reading. Now, my problem is how to make digital integrations for speeds resulted.

    I need to know a method to do the numercal integration.

    Hello.  I guess you're wanting to integrate the speed to track the position of your robot?  LabVIEW has Integration & differentiation screw that should do the job.  In addition, depending on the configuration of your robot, you can calculate directly measured the count position of the encoder based on the resolution of the encoder and the diameter of the wheel.  I hope this helps!

  • What is the speed for OS 10.10 on 13-inch, early 2009

    My 13-inch, Early 2009 MacBook runs with OS 10.9.5 basically OK on speed, and it's a very good, loaded with the fine software is useful but old and slow sometimes with all additional popups and deflect and is very nervous about the links I don't want and mail that I didn't delete.

    The system is pushing me to the update/update 10.10 and I continue to resist the Apple push, the fear of losing what I have and I'm really happy with.

    I was looking for the answer among existing similar concerns, but did not get the simple answer and clear what will I win by the new OS 10.10.

    My fear is real or just scared?

    Apple has removed 10.10.5 and 10.11.5 from the App Store, so only your option upgrade is 10.12.

  • Having more than one user affect the speed of my MacBook Pro?

    I have a MacBook Pro, which is now painfully slow 2011.

    I have three users each journal entry/exit in the required form.

    Having more than one user affect the speed of the Mac or not?

    Thank you

    If you open a session there should be no impact.

    You can view a report of etrecheck for more Analytisis

    www.etrecheck.com

  • iMac 27 "mid-2011 - Intermittent problem with CPU fan running at full speed and sleep mode.

    Hello!

    My iMac 27 "has an intermittent problem with the CPU fan runs at full speed. Sometimes it happens at the time when I start it, sometimes only in my session, and sometimes only after a certain time. So does seem to be a problem of "heating".

    Second issue is with the mode 'sleep'. It may occur also at any time, at the start of the iMac, session, or after a certain time. But once he starts to go in mode 'sleep', when I wake up, it goes right back in mode after a few seconds and that it will continue indefinitely until I restart the computer.

    What could be?

    Please help me!

    4ntoine

    Here is my model of iMac:

    iMac 27 "mid-2011 model 12.2

    Intel Core i7 3.4 GHz

    AMD Radeon HD 6970M 1024 MB

    OS X El Capitan 10.11.6
    SMC 1.72f2

    Boot ROM IM121.0047.B23

    reset the SMC

    Reset the management system (SCM) controller on your Mac - Apple Support

  • Mini Mac server - attachment of external hard drives file transfer speed

    Hi guys!

    I wanted to increase the speed and storage capacity to transfer to my Mac mini file, so I bought a box of external hard drives. The one I bought is: http://www.icydock.com/goods.php?id=219

    Built-in the Mac mini hard drives transfer the file to 60 MB/s (writing and reading) and I wanted to get better speed of file transfer, so I bought an SSD that is going to be inside with an another HARD drive of 3 TB for archiving my files. The housing is connected by USB3.0 (5 Gb/s) for the Mac mini.

    [SSD-> files I opened every day] - speed around 550 MB/s write and 500 MB/sec in reading

    [HDD-> Archives, files that I have does not open very often] - speed around 150 MB/s write and 150 MB/sec in reading

    So I did some benchmarks on my new Setup, and the speed is not really what I expected. Transfer of file max speed I have achieved is about 100 MB/sec in writing on the external SSD plugged into the mac mini. This transfer has been filed since an iMac 21 "2011 with an SSD (with almost the same speed read/write than the box) so it's quite disappointing.

    It is possible that the Mac has a 'file transfer speed limit' is somewhere? Or whatever else that could affect that?

    More information on my setup:

    Mac Mini server 2012 - 2 TB RAID 1 - Mac OSX 10.9.5

    iMac 21 "2011 - Crucial SSD 275 Gb - Mac OSX 10.9.4

    IcyDock external enclosure - 4 bays, USB3 5 Gb/s

    -Red WD HDD 3To

    -Crucial SSD 1 TB

    Together internal Gigabit Ethernet network

    Thank you!

    Was perhaps Spotlight indexing external at the same time, the test has been done?

  • Speed display for runs Watch OS3

    Hello

    To my despair, I can't display the speed for my short... it will only allow pace!

    I know most avid runners say pace is the metric to use, but I've been running on speed for years, I love it and that's what I want to see...

    My Garmin allows this option without any problems. And I don't see how I can use this Apple Watch as my single unit without this feature...

    Is there a planned fix? honestly, be able to customize things a bit...

    Thank you

    Guillaume

    Hi William

    Speed is not currently available as a measure within the app to drive integrated for Indoor workouts or Outdoor running.

    I'm afraid that no one here can tell you about what of Apple's unannounced plans (there is a community of support based on the user).

    If you want to send feedback or feature requests to Apple, you can do so here:

    https://www.Apple.com/feedback/watch.html

  • Site XFINITY Speed Test, no results.

    I'm going on the XFINITY Speed Test site and try to get my test results, but start the speed Test does not appear?  I used this site many times in the past.

    Could be a cookie problem.

    If you use Safari...

    Go to the Safari menu bar, click Safari > Preferences then select the Privacy tab, then click on: Marches site Data , and then click remove all.

    Then quit and relaunch Safari and try again > http://speedtest.xfinity.com/

    I just tried the test and it works fine for me on Safari 10.0.

    If the deletion of cookies did not help, make sure that Flash is up to date.

    Open system preferences > Flash Player, click the updates tab, and then click: check now

  • What is the speed of the hard drive of the 2015 2 and 3 to merge disks partition?

    I was looking through the Apple site and was wondering about the speed of the drive in the iMac in car merger. On their site it says that the 1 TB Fusion drive has 24 GB of Flash memory, and 2 models to and 3 to have 128 GB of Flash storage. But it does not say what the speed of the hard drive partition, which is what I want to know. It is 5400 RPM, or even 10000 rpm or 7200 RPM? I don't know, but I want to know. If anyone here knows the answer to this question, I would appreciate a response. Thank you.

    I have seen it reported that the Fusion drives are all 7 200 RPM.

  • Beta by OOKLA speed test

    Since the update to the latest version of Safari, I was not able to access beta.speedtest.net by OOKLA (the no flash version).  I can access it using my Macintosh plus former 10.5.8 running, but does not on my iMac running 10.11.6 with Safari 10.

    All attempts to enter this URL returns the speedtest.net (flash version).

    Anyone know this problem?

    I tried to clear my memory cache of Safari and flushing the DNS cache, but still no joy.

    .. .a update.

    I was able to successfully run the other speed tests no flash with Safari 10 (e.g., Verizon and other speed test), but trying to access beta.speedtest.net, I'm automatically redirected to the flash-based OOKLA test.

  • Why my download speed goes down when I try to download sierra of macos?

    I am trying to download sierra tacos my download speed will 5megabytes per second to 500 KB / s... Is there a problem with the servers or am I the only one who has this problem?

    I imagine that millions of fans all around the world are trying to download at once. That's what usually happens with a new OS x (Mac OS). It is to be patient with the slow download or give it a day or two until that things have settled a bit.

  • Software updated 2 days ago. He stuffed the speed up to a point, I had to borrow someone's HP to complete a task. Very disappointed

    I updated my software for macbook pro 2 days ago, which has been for his security etc.

    After the update my macbook snaps every minute and the speed it exceptionally slow to a point as I sit for 5-10 minutes waiting to open finder or safari to open. This update plush speed of my macbook. He now works at all. Display and all that remains is very good.

    I have an important assignment due this Friday, fortunately someone lent me their HP to complete my task.

    very sad and disappointed with this, Apple.

    Please provide a solution.

    Thank you

    kitss

    Download and view a report of Etrecheck:

    http://www.etresoft.com/etrecheck

    Ciao.

Maybe you are looking for

  • I had to uninstall firefox because it was causing so many problems with my computer. I was using the latest version 18. What is the problem?

    I had nothing else problems since I installed the latest version of Firefox version 18. It crashes my computer no matter what I do. Even if I do not use the browser. I uninstalled three times and the problems just seem to be deteriorating. Finally, I

  • Upgrading FVS318G default 3.1.1 - 08

    Hello I'm moving my FVS318G to 3.1.1 - 08 but it doesn't. I have download the new firmware and the progress bar starts but after a few seconds the browser page refreshes then and a connection reset error is given. I tried to reboot and download it ag

  • How to concatenate files of CT in DiaDem

    I saw the post on how to concatenate CSV files on tiara... but how do concatenate you files TDM together? I am surprised that this feature is not built into the software as it is a fairly common task, and the script is probably beyond the capacity of

  • advantage of ink HP 4515: cartridge error problem is not compatible

    Hi guys, please help me to solve my problem on my advantage of ink printer HP 4515, I brought in Saudi Arabia and take him to the philippines... im using the HP 650 Middle East ink cartridge when I was in Saudi Arabia, I use that twice my printer and

  • SRW2048 and a Cisco 1841

    I am trying to Setup VLAN between a 2 and a Cisco 1841 router SRW2048 switches. I have ports that connect the 2 switches to the other and the port that connect to router as junction ports. I set 2 VLANS. VLAN 1 is just the vlan by default everyone ru