Role of office remote 2008R2 and Twain?

Similar Questions

• Office locks upwards and not Windows Server 2008 R2 remote let me reconnect

  I was having problems connecting to a remote system with RDP.  The server is operational for several years and is one of the 4 servers identical servers located on the same site.  Recently, one of the other servers crashed I was remoting in a long time so I had to start using this RDP server in.  Once our on-site personnel COMPUTER redirected to this NAT. port forwarding by server, I was able to connect remotely to make some changes, including the addition of a role as a remote access server VPN using the Routing and remote access Server Setup Wizard and removing the component of protection against threats Symantec Endpoint Protection network so that I can use and configure the Windows Firewall.

  While working through the Routing and remote access Server Setup Wizard, my locked up and disconnected RDP session.  I was able to reconnect once on-site staff completed the wizard and restart the computer, but once I reconnected it, after a minute or 2 I was even once disconnected and could reconnect not until the server has been restarted.  I presume that add the VPN role affected my RDP access and decided to remove the VPN server role.

  Now, I can't RDP on the server unless it is freshly reset, and even then it only allows me to stay connected for a few minutes before the connection is lost and I can't reconnect again until the server is restarted.  A vicious circle; power of connection after restart, only to have the connection dropped and requires a restart to reconnect again.

  This server also hosts a database that client systems are able to access for a short period of time after before restarting their connection drops.

  I quadruple checked the inbound Windows Firewall rules, uninstalled application anti-virus completely, same goes for as much as duty get their request for removal to ensure each piece of it has been removed, and I always have the same question.

  The whole issue started when I tried to add the VPN role.  I can't uninstall and then reinstall the anti-virus repeatedly has not helped either, but as it is right now, I have a server who, shortly after the restart, is unable to communicate. not with the internet, not on the local network, not remotely.   On-site staff are trying their best to follow my troubleshooting over the phone, but he arrived at a point where I will have to find out what's wrong and provide an easy solution to remote, or make a trip to halfway around the world to try to figure it out myself (which would be EXTREMELY difficult/close to impossible right now).

  Quesitons:

  (1) why would I be able to connect to remote after the reboot and disconnected then shortly after? (Service/application causing the problem didn't start until shortly after a restart?)

  (2) why is it not only kill remote access, but access LAN and internet on the server?

  (3) what else can be verified to help diagnose and fix the problem?

  I did a lot of research on the web but haven't found identical to mine problems.  Is this a new problem or a bug?  I saw information about uninstalling a patch and a seen a fix for the problems of the RDP, but who wouldn't even help LAN and access on the internet server.  This server ran local client local RDP, access to the database access and could have access to the internet for the years leading up to the recent changes and issues.

  Edit: The pro I'm remote on the server is a system Win 7 Pro, and the database of customers are also Win 7 Pro.

  Correction of the problem.  Turns everything by making the configuration for VPN, incorrect information has been entered in the network link, causing the network to the bomb once VPN service started.

  There are several LAN ports on the server, and one of them was selected incorrectly and configured with the incorrect gateway IP address during configuration of the VPN server.  Once the misconfigured for the LAN port TCP/IP parameters have been removed, all was good again.

• Computer target hung and RDP held while making the Office remotely in Windows XP Professional

  Hello

  I have problems with Remote Desktop for Windows XP Pro SP3. The scenario is as follows

  1. Target computer is Windows XP Pro SP3
  2. Client PC also has the same OS
  3. With the RDP Client, computer target hung. On the client, it is show as trying to connect and continues for a long time
  4. On the target pc, even keyboards and mice do not work
  5. Any application working on the target computer is also get hanged
  6. The only way to normalize the target computer is restart

  Under Remote Desktop, we have already given all the required permissions. Please note that

  • The firewall on the target computer is OFF
  • Symantec antivirus is installed
  • RAM is more than 2 GB
  Can someone advise me on this?
  Thank you.
  Kind regards
  Feraud

  Hi Feraud,

  Thanks for posting your query in the Microsoft Community Forums.

  According to the description of the problem, it seems that the remote desktop connection is blocked on the target computer.

  I will certainly help you with this issue.

  Here are some methods that you can try in order to solve the problem.

  Method 1: Temporarily disable the antivirus from Symantec and check.

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Change the listening port for remote desktop and check.

  http://support.Microsoft.com/kb/306759

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  For more information, see the links.

  The problems of desktop remotely

  Note: Applies to Windows XP

  How to use the Windows XP Professional Remote Desktop feature

  If the problem persists or you have any other questions about the remote desktop connection, do not hesitate to let us know. We will be happy to help you.

• Weired problem with Remote desktop and WLan on Tecra M7

  Hello

  I regularly use Microsoft Office remote to connect to my work PC to my laptop (TOSHIBA TECRA M7 Tablet) home.
  However, since buying (not had long), the remote desktop connection drops and I can't reconnect to the Toshiba laptop.

  It seems that when I connect to the start via Remote Desktop and the connection start screen appears after a short time 10-25mins laptop Toshiba Wifi connection drops.
  When I try to reconnect it does not allow me to do.
  I have to physically come back home and logon to windows XP and then re - activate the wifi.

  I did the following to here.

  1 UPDATE the latest BIOS
  2 UPDATE WIFI INTEL PRO ADAPTER TO THE LATEST DRIVERS
  3. NOT MY BROADBAND, AS PREVIOUSLY, HE WORKED WITH HAPPINESS ON MY OLD LAPTOP.
  4. NOT MY WORKING BROADBAND CONNECTION WORKED FINE BEFORE AND IS STILL WORKING ON THE OLD INSTALLATION
  5. HAVE YOU TURNED OFF ALL THE POWER ON THE LAPTOP AND WIFI PROPERTIES MANAGEMENT, WHERE HE WOULD SLEEP.

  PLEASE HELP, IT IS NECESSARY FOR EMERGENCY

  Hello

  Do you use the Intel Proset utility to configure the WiFi connection?
  Try to configure the WiFi network using this tool and check if the WiFi network would disconnect again.

  I m also interesting this driver Wlan did you use?
  Did you use one page of Intel?
  If this is not the case, check the Intel page for the new WLan driver version.

• RVL200 - cannot use Office remotely through firewall

  I bought this RVL200 a couple of years and put in place in a small office.  I had the configuration work that I can use VPN SSL to establish a tunnel to secure my home, at the office, then use the remote desktop client from my home PC to run the host RDP on any PC on the LAN Office.  Unfortunately, the RVL200 started doing something strange and I had to reset to factory default settings.  Now, I can't get the settings right so I can use Office remotely in the same way that I was using previously.

  My PC at home, I can connect to the RVL200 to the functions of "remote management".  When I create a VPN tunnel from the same computer to the RVL200), it SEEMS to connect in the same way, what he has done.  I can see the "lock" in my system tray and I also see a log on the RVL200 entry that says "user login successful."  But (once the VPN tunnel is go), when I try to start the RDP on my home PC client cannot connect to the host on the LAN desktop RDP.

  I could probably "work around" the problem using port forwarding on the RVL200 (forwarding 3389 to my computer ' target')... but I don't want to do that.  I want to be able to access the ONE of PC LAN via RDP (as I did before).  I'm sure I'm missing a few critical configuration settings, but I can't understand what it is.  Any ideas?

  The settings currently on the RVL200: gateway mode (looks like maybe this should be the router, but I don't know?-the ADSL modem is a speedstream something thing-or-other); RIP with disabilities; No port forwarding; DHCP enabled, all "general firewall" settings are turned on - with nothing blocked. I have "authorized" port 3389 to the WAN interface for a range of ports that includes my external IP address (source = this range of IP addresses - destination = no matter)... I think that these are the key parameters.  The phone line enters the DSL modem, which is then connected to the RVL200 which then connects to the LAN switch / hub.

  Any help would be greatly appreciated!  Thank you

  Adam

  I finally figured it... I changed the router LAN IP address by default - put it on a different subnet.  To enable connections VPN work I had to change the range in the virtual path to the same subnet.  (I thought it would be something pretty basic!)

• How to set up the Office remotely between two pc in different countries

  Hi, I just want to know how to use Remote Desktop between PC Windows 7 in different countries...

  I just tried Windows remote assistance but it take too long to set up first help me post the invitation file and the key to past and then I download the file and open it with Windows Remote Assistance and then copy the access code and enter it in the text box vacuum... and blablablabla

  I have seen a lot of video on how to set up remote desktop for always as when I want to use remote desktop, just ask the user on the other computer and connect it
  How can I do
  Thank you

  * and what is Remote Desktop connection software in windows 7? (next to the Windows Remote Assistance) 

  
  
  looking for help

  First of all know what version of Windows 7 is running on the computer you want to access remote/control. Go to the Start button and type winver in the search window. Windows will report to the version in a pop-up window on your desktop.

  ***********************************

  Assuming that the computer is running Windows 7 Ultimate or Pro...

  The main steps are...

  • Activate [DRC] Remote Desktop on Windows 7 Ultimate DRC PC host.
  • If the login ID DRC on the Windows 7 Ultimate DRC host PC is not an administrator, and then add the user to the remote desktop users group. Don't forget the DRC connection user ID are local on the host Windows 7 Ultimate DRC PC not the DRC PC client.
  • Make sure that there is an exception in the Windows Firewall, or any third-party firewall on the Windows 7 Ultimate DRC host PC.
  • If the host Windows 7 Ultimate DRC PC is behind a router make sure that TCP Port 3389 is transferred to the LAN IP (static is preferable) of Windows 7 Ultimate DRC host PC.

  You can test TCP Port 3389 port through your router forwarding by going to the http://www.canyouseeme.org test site. For help setting up through any router port forwarding, go to the PortForward.com site for help. Ignore references to UDP Port 3389.

  http://PortForward.com/English/applications/port_forwarding/Remote_Desktop/Remote_Desktopindex.htm

  Test call Windows 7 Ultimate DRC host PC from another PC or laptop computer on your local network using its LAN IP address (static is preferable).

  http://theillustratednetwork.MVPs.org/RemoteDesktop/TroubleshootingDiagrams/Basic.html

  To call from a remote location using the public IP address of the router to the PC host of Windows 7 Ultimate DRC is behind or a full domain name [FQDN] of DynDNS (which I assume that you have already configured).

  Its highly recommended that you use Network Level Authentication [KLA] If you connect remotely from a Windows 7, Vista or XP SP3/SP2 client.

  http://Windows.Microsoft.com/en-us/Windows7/what-types-of-Remote-Desktop-connections-should-I-allow

  http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6ConfigRecommendations.html#SP3

  http://theillustratednetwork.MVPs.org/screenshots/RDC-NLAandServerAuth/host-UseNLA.jpg

  http://theillustratednetwork.MVPs.org/screenshots/RDC-NLAandServerAuth/ClienttoServer-UseServerAuth.jpg

  Make sure that you use the latest version of the client if your connection from a client computer to Vista or XP SP3/SP2. Windows 7 includes the new RDC client software.

  http://support.Microsoft.com/kb/969084

  General help written for Vista, but close enough to Win 7...

  http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6ConfigRecommendations.html

  MSFT Win 7 DRC help pages...

  http://Windows.Microsoft.com/en-us/Windows7/allow-someone-to-connect-to-your-computer-using-Remote-Desktop-connection

  http://Windows.Microsoft.com/en-us/Windows7/connect-to-another-computer-using-Remote-Desktop-connection

  http://Windows.Microsoft.com/en-us/Windows7/allow-remote-desktop-connections-from-outside-your-home-network

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-using-Remote-Desktop-connection

  http://Windows.Microsoft.com/en-us/Windows7/search?q=remote+desktop&PRD=Windows7

  ***************************************

  If the remote computer runs Windows 7 Home Premium...

  Windows Live Mesh 2011 remote connections works well for the access/remote control of a computer Windows 7 Home Premium. It gives you a nice Remote Desktop display type of the Office from remote computers.

  http://explore.live.com/Windows-Live-2011-system-requirements

  You can use a web browser to access without installing any software, other than an ActiveX control, on the remote client or install Live Mesh on the client. Your choice.

  http://explore.live.com/Windows-Live-Mesh-Remote-Desktop-using?OS=Mac

  http://explore.live.com/Windows-Live-mesh-devices-remote-connections-what-UI

  If you use Live Mesh Remote Connections I suggest to create a Live ID limited account type that does not include an e-mail account. I have install a limited Live ID I use only to connect to some Live Mesh remote connections to computers I want / access control.

  https://accountservices.passport.NET/ppnetworkhome.SRF?VV=1200&mkt=en-us&LC=1033

  You can, if you wish, also use an existing Live ID or create a new, but this is your choice.

  I installed Live Mesh 2011 on desktop Win 7 Home Premium to my wife and in distance/access control can it go literally anywhere. Sometimes I use the web based (IE. Method ActiveX) from my laptop on the desk.

  Here is an example of a session Windows Live Mesh 2011 remote connections on my laptop computer for access to the / remote control of desktop Win 7 Home Premium to my wife.

  https://SkyDrive.live.com/redir.aspx?CID=25ab668da65c8fbe&RESID=25AB668DA65C8FBE! 402 & Thierry = 25AB668DA65C8FBE! 118

  https://SkyDrive.live.com/redir.aspx?CID=25ab668da65c8fbe&RESID=25AB668DA65C8FBE! 401 & Thierry = 25AB668DA65C8FBE! 118

  Otherwise if you want to remotely control a computer looking Windows Home Edition to TeamViewer (free for personal use) or VNC (my favorite is UltraVNC with its encryption plugin) as the other two alternatives.

• Toshiba 40 HL 93 R does not remote or and door panel

  Hi all.
  My Toshiba 40 HL 93 R does not remote or and door panel.
  I guess the TV is blocked or immobilized because remote is 100% functional.

  How can I unlock TV? Combination or other. I can't find anything in the manual of the TV

  I put t think that the TV is locked... to my knowledge, it is possible.
  You can block single channels setting a password, but this does not affect other functions of the TV.

  Disconnect the TV from the food sector and wait a little crisper.
  Connect the TV to the network, then press power button to power ON the TV

  It work?
  In case it doesn't, you should contact the service point because it seems that your TV equipment is affected.

• My 5s possible remote jailbroken and hacked so I share the same ID Apple and the person knows my passwords?

  My 5s possible remote jailbroken and hacked so I share the same ID Apple and the person knows my passwords?

  N °

  What makes you think that this could happen? If you share an Apple ID with someone and they know a lot of your passwords, they have access to a lot of your information. Change your passwords.

• Hai iam Amaladas from Chennai (India) iam Remote Sensing and GIS researcher here most people using the Google Earth application and five members using Iphone, we need a Google Earth app (India)

  Hai iam Amaladas from Chennai (India) iam Remote Sensing and GIS researcher here most people using the Google Earth application and five members using Iphone, we need an app (India) of Google Earth?

  https://www.Google.com/search?q=Google+Earth+app+India&ie=UTF-8&OE=UTF-8

• W520 - Windows Server 2008R2 and color sensor

  Good evening

  Does anyone have experience how to do calibration working under Windows Server 2008 R2? It beeps 3 times when I close the lid and displays the message that the system cannot be put into calibration mode.

  Thank you!

  If you have installed the calibration software after that Office R2 experience and the latest video driver NVIDIA Windows 7 x 64, so you have done everything you can.

  If it works on Windows 7, but not when started the R2, then this is clearly a software problem and whereas Windows Server 2008 R2 is not supported, you're probably in a dead end.

• Microsoft Office Access Runtime and Data Connectivity 2007 Service Pak 2 will not update

  Today, I upgraded my Vista Ultimate Edition of Windows 7 Ultimate and checking the updates it listed 10 important updates. I went back in and there was still the major update 1 "Microsoft Office Access Runtime and Data Connectivity 2007 Service Pak 2 (SP2) who refuses to update which results in an error. I tried several times with the same error that results. Any suggestions as to why?

  The update could not update with no error code, just says 'update failed." However after that restart and check the view of the update the update again must have occurred because it is no longer returns in search of updates.  Thanks for responding to my problem

• ErrorCode A97 installation: Microsoft® Office Access Runtime and Data Connectivity 2007 Service Pack 2 (SP2)

  How to avoid this update (it retains pupping upwards each time).

  Hello Marcel.Pont,

  Follow the steps below to solve the problem:

  1. Start - Control Panel - programs and features - in the left pane, click View installed updates - uninstall Microsoft Office Access Runtime and Data Connectivity 2007 Service Pack 2 (SP2) update.

  2 restart the computer.

  3. download the updated Microsoft Office Access Runtime and Data Connectivity 2007 Service Pack 2 (SP2) manually from the link below and install it:

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=6F4EDEED-D83F-4C31-AE67-458AE365D420&displaylang=en

  Samantha M S

• Downloads, but wont install a security update for Office 2003 (KB2760574) and (KB2726929) XP 2003. Install other updates. Error code 0 x 80070643

  Downloads, but wont install a security update for Office 2003 (KB2760574) and (KB2726929) XP 2003. Install other updates. Error code 0 x 80070643

  If you are logged in to your profile, the mark as answer button should be available at the bottom of all messages (except yours).  If this isn't the case, I can have a moderator do it for you, Bill.

• MS Office 2010 Pro and my printer does not work,

  I just installed MS Office 2010 Pro and my printer does not work, I tried to print a test page for the printer, but that prints either, ask if I want to troubleshoot the printer and when I click on Yes, I get a message that there is a problem of ActiveX.  The printer will not print not any application, but it worked before installing office.
  All the apps work except in order to print it.
  I am running WinXPPro w/sp3.

  Jim K.

  Hello

  1. What is the exact error message?
  2. don't you make changes on the computer before the show?
  3. What is the brand and model of the printer?
  4. this problem occurs with all files that contain the Active X objects or specific file?

  Method 1:
  Run the fix it and check.
  http://support.Microsoft.com/mats/printing_problems/en-us

  Method 2:
  Try the steps in the link and check.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 3:
  

  This problem occurs if the security settings for the Local computer zone are configured to prevent the ActiveX content to run.

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry : how to back up and restore the registry in Windows

  a. Click Start and run, type regedit.exe, and then click OK.

  b. expand the following registry subkey:

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Internet Settings\Zones\0

  (c) in the right pane, right-click 1200 and then click on edit.

  d. in the value data box, type 0. Then, click OK.

  e. close the registry editor.

• Is it possible to restrict the Office remote to only the group "remote users?

  Hello world

  Bit of a strange request. Within our work environment, we try to limit as much as possible to Remote Desktop. However people regularly have administrator rights in order to do their job, due to some programs and restrictions works not very well.

  What I'm looking for is essentially:

  -Nobody has the rights to remote desktop, USERS in the group "Remote Desktop"

  -It is administrators - they can't have these rights

  Is this possible? My understanding is that permissions are cumulative, if for example Admin is user of remote desktop and then some. I would like to somehow separate these (whether by a GPO or other).

  Any advice or suggestions are appreciated!

  Hello

  You can display the query in the technet forum for assistance.
  http://social.technet.Microsoft.com/forums/en-us/categories/