Similar Questions

• HP Deskjet 2540: My printer cannot connect to the wireless network (SSID is not found)

  Hello

  I have a HP Deskjet 2540 printer that is configured to print using the USB cable, and I have no problem printing through it. I just bought a router (D-link DWR116) and I'm trying to set up the connection to the router wireless to my printer. When I use the printer setup & software and select the option "convert a connected USB printer wireless", I can choose to enter into the setting of the printer access the router automatically or manually. These two will come with the same problem where the program is my name SSID of the router successfully but then failed to connect to what the SSID is not found.

  It comes on it comes up with the error message:

  Question: You have manually entered the name of the network (SSID) cannot be found.
  Solution: Check that your wireless router is powered. When to manually enter the name of your network (SSID), make sure you enter exactly including upper and lower case and spaces.
  ============================================================================================

  Which is meaningless because it came with the SSID earlier and I chose what options the wireless network available. I tried to manually enter the SSID, but after entering the password for the router, the same error message appears.

  Help, please.

  Thank you

  In fact, I solved the problem. Something about the wifi light on the printer. It can not be flashing, I don't know what the blue light flashes on the wofo of the printer, but I don't think that it means that the wifi is on.

• "Gateway router not found" error when you try to connect the TiVO DVR with DLink router.

  Original title: gateway router not found

  try to connect the tivo series 2 to the internet with dlink router that he used to work with previous tivo but not with tivo now, it says gateway router not found
  However, my laptop works fine with the router, I tried tivo support nothing helps, too, if I use the phone line works of tivo, but do not store a lot and is running out of room so it will not work fo rme, helllpppppppp thanks

  Hello

  Where exactly you get this error message?

  See the troubleshooting suggested in "Network error message N07 or C107" steps from this link.

  If you try to connect the tivo series 2 to the internet with dlink router then check out the link below:

  http://support.TiVo.com/app/answers/detail/A_ID/400

  Please contact the manufacturer.

• Linksys - router bridge - E8350 path not found network

  Dear community of Linksys,

  I recently bought a Linksys E8350 router, to replace the old AP in my network domestic.

  To make the installer of my clear network, I did a little diagram:

  

  So, as you can see, at the top left is the router/modem provided by my internet provider (Telenet, Belgium).

  I have a wired connection in my room, where I have my desktop and NAS connected computer. I also plugged the

  Linksys E8350 that is configured in Bridge mode. My laptop is connected wireless to the E8350.

  On the E8350, I disabled DHCP and NAT and gave him a static IP outside the range of my other router.

  My problem:

  When I go to the network through windows file Explorer, I can see my desktop from my laptop and vice versa.

  But when I double click to access one of them, I get the error message "network path not found".

  Connection via start > \\Computer-name gives the same error.

  Since my laptop or my desktop, I can see my NAS on the network. I have internet on all my devices:

  My office through internet cable connection, my laptop has wireless internet connection trough

  and I can evaluate my NAS from the internet.

  When I remove the E8350 entirely from my network and connect my laptop a hollow wired connection.

  everything works fine. I can see all the devices on the network, connect to my NAS and share files between computers.

  Things I tried already:

  -My PC and laptop are both in a 'private network '.

  -J' disabled my firewall

  -Everything is activated in the menu "sharing advanced settings."

  -J' tried to connect the E8350 to the switch via the Ethernet or WLAN port, nor to solve the problem

  -J' tried to change the NETBIOS settings

  -I don't have your antivirus software that might interfere with something

  -J' updated the firmware on my linksys router to the latest version

  To be clear, the problem occurs when I put the E8350 in my network, otherwise everything works perfectly.

  I hope that I have provided some information decent on my problem, because I can't seem to figure it out myself.

  Thank you in advance.

  Pindox

  The topology of your network is effective from your diagram. With the E8350 in mode bridge in this topology is WAN is connected to the network switch.

  Many devices of bridge no hand NetBios address very well. In some cases, the best way to access the network through a bridge device resources is to use remote devices IP address instead of its computer\device network name.

  In Windows, you can drive old school card NAS records using the IP address of the Servers\NAS:

  PC command line:

  NET use s: \\192.168.0.3\my_nas_folder / persistent: Yes

• Router not found - EA6500

  I'm configuring my settings of connectivity on my E6500. I type 192.168.1.1 and the logon screen comes up. I tried signing in with my username and password and also disconnect from the internet and the connection the router password. After that I connect, 98% of the time it says router not found you have not logged to your router. It's funny told me that since this Web page is provided from the router because I unplugged the internet. Even with the internet, it does the same thing.

  The time it loads the home page of the router, I click on connection and when it comes to the top, the page is just blank with buttons Ok, cancel, and apply.

  I did a reset on the router and it reconfigured with the CD and tried everything above again and same results.

  I don't remember which is a problem when I first set up the router, it seems that a new firmware has been installed automatically. I see no any info on what is a known problem with the latest firmware. Everyone knows about this problem?

  How you try to connect? 192.168.1.1? MyRouter.local? or www.ciscoconnectcloud.com ?
  Try to repair the connection to your computer or empty the cache of Dns resolution or the cache of the browser.

• I'm unable to watch videos on a certain type of site. They all now say, 'file not found '. They worked until I added a router for my Kindle Fire.

  I used to be able to watch videos on a certain type of site now all say file not found windows vista. I recently added a router for a kindle fire

  original title: streaming videos

  Hello

  ·          Do you mean that you use Internet Explorer 6 in Windows Vista?

  Windows Vista Internet Explorer 7 default features.

  http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using

• SMALL BUSSINESS NOT FOUND IP ROUTE

  Hi everyone I need help my bussiness small cisco SG-500 52p not found the command IP ROUTE.

  the cause is an electric Cup, my small bussines factory reset

  Hi Rafael, may also check that the switch is in mode switch or router? It is possible when the power lost, the config was returned to the last known config (the last time that the recording of the config file).

  -Tom
  Please mark replied messages useful

• So, updated for Win 7. Clean install. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Clean install. 2 problems. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Probably you run first win7 Upgrade Advisor, who did you would probably show your system as not supported under win7

• Win7 64 bit, connects to the router, but no error internet access-"page not found".

  Original title: Win7 64 bit, connects to the router but no internet access.

  Help! Windows 7, XP Home Edition Premium, 64 bit, connects to the router and I can access the network. However, I can't access the internet. PC was working fine until a few days when I was using IE Explorer and I suddenly got the error "page not found". This pc internet connection uses the onboard network controller. I rebooted the pc and used the option "safe mode with network. The pc worked fine and I had access to the internet. I restarted the pc and still no access. I tried a usb wireless adapter. No luck. I have not installed updates or software recently. My other 2 PC works fine. I tried to use the network troubleshooter and he could not find any problems.

  Hello

  1. Have you made changes on the computer before this problem?
  2. What antivirus application do you use?

  I suggest you try these methods and check the status of the issue.

  Method 1:

  Keep the computer in a clean boot and check the status of the issue. If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem. Continue with the remaining steps to pin-point on the third party service. After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7.

  http://support.Microsoft.com/kb/929135

  Note: Please go up to step 7 of the Kb to maintain the computer to a normal startup after you fix the problem

  Method 2:

  I would suggest trying the following steps and check the status of the question.

  a. open Internet explorer.

  b. click on tools, then on Internet options.

  c. click on the Connections tab.

  d. click on LAN settings.

  e. uncheck the option use a proxy server for your LAN .

  f. save the changes by clicking on apply and ok.

  Method 3:

  Configure Internet Explorer to disable simplified HTTP error messages and check the status of the issue.

  a. on the Tools menu, click Internet Options.
   
  b. on the Advanced tab, in the browsing section, disable friendly HTTP error messages display check box and then click OK.

  c. close Internet Explorer.

  d. restart Internet explorer and check the status of the issue.

• END point URL for the routing service BSE says not FOUND

  Hi all

  For services of routing in BSE, the WSDL link opens the fine, but the link to endpoint URI for the routing service fails with the message below the message. When I invoke the WSDL with SOAP UI, I'll be back the same error message. I tried to bounce the server, but no help. I also noticed that this slide ESB_Projects Directory gives error 404 on any browser.

  Then, when I click below url for all the routing service

  http:// < hostname >: < port > /Event/ < systemName > / < serviceGroupName > /AddressStandardizeRS

  I get the error in the browser - below

  Not found

  The URL /event/ requested < the system name > / < group name > / < Routing Service name > was not found on this server.

  Oracle-Application-Server-10g/10.1.3.1.0 Oracle-HTTP-Server Server at odevsoa.local1.wbcgp.com Port 7777

• Network not found

  Printer: OfficeJet 4500 Wireless (CQ663A)

  OS: Windows 7

  Router: Netgear824v3

  Channel: 6

  Type: Infrastructure

  Mode: Automatic 108Mbps (selection automatic b/g)

  Security: WPA - PSK

  SSID broadcast: enabled

  Question: network not found.

  two week, Samsung laptop computer (Win7) is located on the network.

  5 months Dell desktop (Win 7) is on the network.

  1 # PS3 connects to the network

  2 # PS3 connects to the network

  Wii connects to the network

  OfficeJet will not find the network.  He finds my neighbors, but not a network for my SSID.

  I repositioned the OfficeJet 15 feet from the router, 6 inches between the router and into another room of the router.  I've moved or shut down wireless devices, speakers, etc., to identify/avoid interference.  I'm confused: why the printer will not detect my SSID broadcast.  It allows to identify the type of secutirty (WPA - PSK TKIP or AES), but can't find my network.  Ridiculous!

  I downloaded, installed a ran HP Network Diagnostic Utility.  He said that the network is fine.  It lists the printer on its own network "hpsetup" but the printer can't find my network to connect when I run USB setup or manual configuration or the wireless Assistant.

  Any help would be great.

  It is certainly strange.  Here are a few ideas:

  1. starting at the front of the printer: Setup > network > wireless network Test.  This will be the radio automatic test to make sure it's OK.

  2. open your Netgear router (type 192.168.1.1 in a browser address bar).  Make sure it has the latest firmware.

  3. While you're here, change the channel to 11.

• WRV200 - "404 not found" when you try to connect to the admin

  After updating the firmware to 1.0.39 - ETSI.img the router is coming fine. (the WRV200 is a European model) The unit seems to work fine. Wireless works with the SSID I set up. My devices can connect to the WLAN using WPA key that I had before.

  BUT: when I try to access the router admin pages returns 404 not found

  Security in my browser is set correctly. I registered a https:// access exception.

  The page that I said:

  404 not found

  File not found.

  Hello!

  Try the following:

  1. check the IP address on the computer. Make sure that your gateway is accessible. You can disable the firewall on the PC as well.

  2 remove THE LAN settings.

  3. use of different browser (e.g. Firefox) will help isolate the problem.

  4. try different computer also.

  5. If still does not work, you can reset the router and reconfigure.

  Thank you!

• Device not found Airport Extreme

  We have an airport extreme connected generation via Ethernet to a switch that provides network access to our entire House (about 10-15 connections) via wifi access points all Ethernet hard wired (linksys + apple) and a direct wire to a PC. Airport extreme is the dhcp and is connected to a gpon fiber using PPPoE.

  The problem now is that the AirPort Extreme disappears from the airport on iOS Mac utility and Windows, it is found however the network and the Internet continues to operate normally on all connected devices. I can also continue ping on the router.

  I have reset the AirPort Extreme to the default settings, but the problem continued...

  I tried to unplug all devices and have AirPort Extreme only connected to him have the fiber but the problem persists...

  no idea how I can fix this problem?

  You describe a known problem with Back to My Mac which first appeared around July 13. The problem manifests itself in a message "Device not found" meant to be displayed in triangular AirPort your AirPort base station with a yellow icon utility, while the router of the device functions others continue to work normally.

  If you use an airport Time Capsule, backups will not work using that device or USB hard drive units connected to it.

  Apple will only be able to solve this problem, so all you can do is wait for them to do. If you want to contact them to tell them about it, using the contact Support link.

  There is a solution: on a Mac, open AirPort Utility and select file > configure other...

  For each of your routers Apple AirPort Base Stations serving their respective networks: its IP address and password (if you don't know either of them, read the Note that follows the horizontal rule below). Then, on the tab of the Basic Station , delete all the entries in the Back to My Mac using the 'negative' button, then click on Update.

  Which must be re-established appearance of this base station in AirPort Utility, as well as in a side bar of the Finder, if all shared disks are plugged on. It will also restore possibility of Time Machine to save on these discs, if this has also been a problem for you.

  If this seems to imply that you will not be able to use Back to My Mac until Apple fixes it, you are probably right. Well to diagnose problems of the CCMM is tedious work that I have not yet finished.

  Apple does not participate on this site except in a very limited way, so don't expect is not a response from them, here or elsewhere for that matter. We'll just have to wait for them to fix it.

• Device not found, but internet work

  I have an Airport extreme with a capsule 2 TB that I use as a backup file.

  All of a sudden I can't connect to the airport time capsule. When I launch the airport utility, there is an orange triangle/exclamation point that fits the description "device not found". The router works well, since I am connected to internet (at this time).

  I tried to unplug the unit and time capsule comes back for about 2-3 minutes until the same problem occurs again. Factory of Soft and hard resets produce the same results. I know this isn't my macbook pro because it does the same thing on my phone as well.

  You have Back to My Mac configured on the TC with your AppleID?

  This has happened to me and when I removed my AppleID and disabled Back to My Mac it ceased to occur and the TC became visible again.

  I hope that Apple will fix this soon but it would pay record a call of support with Apple on this topic as well.

• Airport Time Capsule device not found

  I have the time Capsule on the airport of the TB 3 802.11ac (bought 9/2014).  It integrates the latest version of the 7.7.7.  Just last week, I received the error device not found (.. .has been previously a part of your network... etc.).  The internet connection is always good and the component of the time capsule router still works.  When I unplug the device, it can find him but eventually will go down in a few minutes.  I also did a warm reboot, but some results.  Printer connected to the time capsule does not, nor does Time Machine back ups.

  Would be grateful of any advice on why the drive not found error continues to occur.  Thank you!

  You have Back to My Mac enabled on the Time Capsule?

  If so, turn it off for the moment in the AirPort Utility and restart the time Capsule.