Router will not connect to internet (modem Comcast)

Similar Questions

• My WGR614v10 router will not connect to internet

  When I connect my computer directly to my modem I have a fast internet connection, but when I try to connect through my router I can not to surf the Internet. MY router was working fine two days ago.

  I just talk about my router, not my modem. In any case, I appreciate your help. Now, I bought one from amazon which works very well. Thank you.

• Router is not connecting to the modem so I can't get internet

  All right-_ - I tried a lot of things with this so I get irritated sorry. Here is my info I have a Linksys Wireless Router with SpeedBoost Firmware Version 7.2 WRT54GS (latest version). I'm trying to use it with a Sprint 645 series Modem. My IP address when you are connected to the router and the router connected to the Modem is 192.168.1.100 who my ISP said was ok to make it work. While it is just connected to my modem, it's the same thing except replace the 100 by 1. My ISP uses a measure of security where The Thing DHCP is 192.168.1.1 and so is the DNS server and default gateway and im not sure if this has something to do with it. I used the ping at a command prompt to make sure that I am connected to the router when its plugged up and it is. This is a new router. I have internet with Modem just perfectly. I tried to reset the router and that does not work-_-. I don't think it is important more because I tried to fix the many way people have told me and it didn't work, but I'll tell u in any case. When I put up the first router time I hung and lit everything at the beginning. Then I noticed that it says Run CD before to connect the cables... those who were not in the instructions but wtv... anyway resetting should have fixed or so I was told by other people on this forum. I use a laptop with Windows Vista, and I don't have access to a desktop computer in case I need a XD. I can connect to the router fine because I can access the Setup page... and I can connect wireless... The ONLY problem seems to be that the router will not connect to the Modem... for some reason of wtv-_ - I think that its because the entire security measure on the way to the DHCP and the DSN and the bridge are all 192.168.1.1, but that's just me. I'm sorry this is very long but I really want this problem-_ - I had this router for a month and becomes really annoying so please help . My ISP is Embarq. I ran the installation CD and I had all through the last step (standby router) after having connected the power supply to the wall for the router. Just, it is there forever and then says "error: 322 cannot find router or something like that." There are 3 steps to try to fix it. It says to make sure that the router is connected (it is), it is said also to make sure that u does not actually connect your old router, (I don't have a-_-) and then re-run Setup. and by the installer, I mean where u plug in all the cables in the right way. * sigh *.

  If you need anything else please ask.

  Your second post says "" ignore this "so I guess everyone thought that you set..."

  When you connect through your router that you have two instances of DHCP past... one is your DSL modem with router IP address on its WAN interface. The other is the router that gives your computer an IP address via the DHCP server on the router. The IP address of the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the reange of Linksys routers LAN IP address is also in this range. For that to work, you must set your router 192.168.2.1 LAN ip, so that the LAN and WAN router interfaces are in different networks.

  To do this, unplug the DSL modem router, power it and your computer, and then connect the computer to the router by an ethernet cable. Turn on the router and the computer, and then go to 192.168.1.1. Change the LAN IP on router 192.168.2.1, save the configuration, and then restart the computer. Once the computer returns to the top, navigate to 192.168.2.1... you should be able to get to the router GUI configuration.

  Turn off the router and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, and then turn on the modem, then the router... you should be good to go...

• iPad will not connect to internet

  Hello

  Recently I replaced my router wireless with an old faithful that d-Link DSL - 502T cable modem as I have now 2 extreme airport to handle a Wi - Fi. I have now a much faster internet access on my Macbook Pro, but my iPad 2 now will not connect to internet.

  Airport utility on the iPad shows that the internet is disconnected, but I don't know how to solve this problem.

  The two airports are configured in Bridge mode. Help someone?

  If you have LAN - 502T running as the main router.

  Bridge the airport should simply pass the DHCP via the Dlink but sometimes it's a failure.

  The two AE connected directly to the modem or the other?

  I would recommend the static method of intellectual property.

  https://discussions.Apple.com/message/25135547?ac_cid=tw123456#

  In this method, you must first AE plugged directly to the Dlink and the second AE connected in the first and bridge... it will dhcp to EI and is often a better configuration with Apple gear. Worth a try.
  

• Watch WiFi is connected but will not connect to internet

  I have an iPad 2 which, all of a sudden (in the Middle streaming), is more connected to the internet.  I rest the network settings, when this does not work, I have reset all settings, stopped and rebooted, all done basically.  It shows that its connected to my WiFi, but will not connect to internet.  All the other devices in my house work, then there must be a problem with the iPad.

  Reset the router: just pull the power for a few seconds and reconnect. No parameter to get lost.  Other devices operating with success is not serious. The router has probably received an invalid address for the iPad.

• My IPad is connected to the WiFi router but will not connect to internet. My Internet works on my IPhone and Mac Book

  Since last night, my IPad connecting to my WiFi router, does not connect to the internet.

  Internet connection works for my IPhone and MacBook.

  Hello

  Go to settings resets the network settings on iPad.

  After reset, enter your key wireless router.

  See you soon

  Brian

• HP dv6815nr: Wireless Card will not connect to internet

  Hey people, trying to make my old laptop back to semi in working order.  Did a fresh install of Vista, but the wireless card for some reason any will not access the internet, says "local use." Internet works as the other computers in the House are connected on the wireless and when I connect the ethernet, features of connectivity cord.  Crossed and uninstalled/reinstalled the driver.  I have no special security here, just the windows firewall, which I disabled the thought that he could block, but it was not the question.  Other ideas you can come up with that would be great.  I have also included the hardware ID for my wireless card.  Pilots have been taken off this site from hp for my computer model as well.

  PCI\VEN_168C & DEV_001C & SUBSYS_137A103C & REV_01

  Hello:

  You need to install a driver update... the problem is probably your router is too new for the old driver wireless deal.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-108905-1 & CC = US & DLC = in & LC = on & JumpID = reg_r1002_usen_c-001_title_r0004

  Go back and activate your firewall if you have not already done so.

• D7000 will not connect to internet after reinstalling

  Hello

  We moved our D7000 modem router from one room to the other and now it does not connect to internet at all. I spoke with our ISP and everything is fine on their end. I connected the modem and reset our ISP connection & the password, and the ISP did the same thing, without effect. The phone line has been tested, it's ok. I swapped the cables to make sure that they are not defective. I moved the modem to return to the old location, but now it does not work there either.

  WiFi seems to be ok and all our devices (phones, tablets, computer) recognize the wireless network and modem, but there is simply no internet connection. It is bizzarre! Nothing has changed, there is no new hardware, no updates or upgrades, the ISP is always the same, the only thing that differs is the location, in the same House.

  The lights on the router modem are as follows:

  Food - white

  Internet - amber

  DSL - off

  WiFi - white

  Any ideas what I could try to make it work again? Should I do a factory reset on it? This could be the cause? Move a modem do not stop working. We only had since November so it isn't old yet, and it has been working fine so far.

  Any help at all would be greatly appreciated!

  Päivi

  Hello

  It has been a while now, but I thought I would update this for anyone interested or affected by the same problem we did.

  After weeks of back and forth with the ISP and try and test anything and everything we could think, including the replacement of the D7000 in store warranty (not just once but), and nothing is helping, the ISP finally filed a foul for us and sent a CET. And what do we know? There was a flaw in the riding of Telstra which he had found, and which caused our internet connection fails. After that which has been set, we are online again. The line still falls here and there and the phone line is cute, but at least we are connected.

  And now I'm fighting with the ISP for refund during all these weeks we were disconnected while they refused to be a mistake for us and have someone out. Time for a new ISP, I think!

  Hope this helps someone else with the same problem there.

  Thank you

  Päivi

• WRT120N will not connect to internet

  Hello

  My router was working so far. For some reason, I disconnected the internet cable and plugged. After that, it does not connect to the internet.

  Based on the forum I acceded to 192.168.1.1, it will display the administration page. I have reset to the factory settings and turned off the router for a while and turned again but it does not help.

  This problem is not only withmy laptop computer. Grateful if someone could help me solve this problem. Thank you.

  Kind regards

  Combot.

  If you have DSL connection, these 2 reasons may be applicable. It's either you must assign the PPPoE router (you must have a username and a password from your service provider.) Or you might need to change the local router ip address. For more information, please visit this link

  http://www6.nohold.NET/Cisco2/UKP.aspx?VW=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.XML&PID=80&r...

• behind the bridge router will not connect.

  Im trying to set up my network like this, Modem > ROUTER1 > bridge > ROUTER2 > PC

  Both routers are WRT110 and the bridge is a WET54g.

  I can access the internet if I plug the power cable directly into my PC from the bridge, but when I plug it into the router it does not connect to the internet. my pc can also connect to ROUTER2 without problem but can not get internet.

  This could be established with only 2 devices... WRT110 router and bridge WET200... WET200 bridge has five ports to connect safely separate wired networks...

  With your existing equipment, cela -.

  Connect the second router Internet Port WET54G and access your router installation... Change the router LAN IP address 10.10.10.1 and click on save settings... Turn off the router for a minute and turn it back on... You should be able to connect your computers wired to your router's ethernet ports, and they need to connect on internet...

• HP Mini 110-4112ea with the atheros wireless card will not connect to internet

  I just bought the above and tries to connect to the internet via my router netgear wndr3700 but cannot make it work. network is the following: Mini 110--->---> Virgin (netgear) supplied wndr3700 router modem (also wireless)---> internet

  Although it shows as having internet in network & sharing Center it just connects and applications like Skype and Norton does not connect. When I give the wndr3700 with ethernet cable that works very well. Also if I join WiFi on a blank area, that's OK. I just want the Mini 110 to attach the wndr3700 wireless and give access to the internet as it should and other PC at home do. I installed the latest drivers from the HP (sp54972 - version 9.2.0.444) site but nothing helped. Help, please!

  Right - I myself solved by finding the relevant info on the Netgear forum. This article describes change some settings on the Netgear router. For the benefit of someone else knows the same or similar problem and for the technical gurus at HP, that's what I did:

  Activate these settings in the configuration of the QoS.

  Activate -WMM (Wi-Fi Multimedia) parameters (b/g/n 2.4 GHz) (box)
  Activate -WMM (Wi-Fi Multimedia) parameters (5 GHz a/d) (box)

  (in my case I need not turn on WMM for the 5 GHz band, but just in case I need it in the future I did anyway...)

  Don't ask why it works or what it means: it works!

• Printer will not connect to internet

  I have a Photosmart Premium all in one Web C309n printer, I have it on a wireless network. When I try to download apps from its touch screen, it can not find the internet connection. I tried with the ethernet cable and get the same results. I have the latest drivers installed and it prints good laptop, as I was never able to scan directly to him to the laptop. If I open the application on the laptop, it works very well, I think it would be faster to go from the screen touchscreen printer. In any case, I can live with, I would like to get my Google calendar to print or view I could be interested in new applications.

  Thank you to me for a new direction.

  There is another problem that occurred after updates removed then reinstalled, I get an error message at startup which said. C:\programfiles\HP\HPphotosmart6520series\bin\hpstatusbl.dll

  How can I get rid of this nuisance?

  

  Hello

  To connect your printer to your wireless network, you will find need the menu internet wireless option on the front panel of your printer.

  After that you will find this option and select internet wirless, you will see the available WiFi networks and you choose your own wifi network and enter the password for wifi for her. Once this operation is completed, your printer must connect to the internet.

  I recommend you to install the most recent drivers that place to the last issue you mentioned.

• Equium A100-147 will not connect wireless Internet!

  Hello
  For these last months that my cell phone was able to connect to internet, I think I must have downloaded a virus that deleted the necessary drivers for the wireless card to work, it is still all access points, but it does not connect.

  I tried to reinstall the operating system (Media Center) a few times - that didn't work, and now I have some drivers that I got from my computer on a toshiba Web site - they don't work anymore.

  I'm stuck now because I've tried everything I can think of and nothing works, so I hope I can get some good advice on here :D
  Thank you

  Hello

  I really put t understand why the installation of the OS is so hard :(
  You have received the Toshiba Recovery CD. On this CD all the drivers and tools are already preinstalled.
  You insert this CD into the CD/DVD to boot from the CD drive and the installation will begin. After 10-15 min the installation will end and the laptop should be ready for use.

  Then configure the WLan access again (encryption, SID, MAC address, etc.) and enjoy.

• WRT54G Router will not connect on my iPhone automatecally

  Router: Linksys WRT54G ver. 2

  Firmware: 4.21.1 (last)

  Security: WPA2 Personal

  iPhone: 3GS

  Can I connect my iPhone to my wireless network, if I broadcast the SSID of the router, but if I turn off the show and then the iPhone can not connect automatically. So, I get the name and the network security code whenever I turn on my iPhone? And I do not broadcast the SSID.

  In fact, Disabling SSID broadcast is a bad thing that lowers your security.  The reason of this, it is related to the problem you are having with your iPhone.  SSID was intended to be broadcast - go ahead and rebroadcast.

  When a Windows-based computer connects to a "hidden" network, should be a note that the SSID is not broadcast.  From that moment, every time that Windows computer does not have a network connection, it will constantly send the connection requests that you guessed, clearly understood the SSID.  If not, how the Windows computer would be able to connect?  He doesn't know that its in your home and close enough to your router.

  The problem is of course that the Windows computer, typically a laptop, will do it everywhere wherever you are.  These packages are easily detectable with the simpler network analysis tools - and striker will be able to detect both your SSID and your MAC without being anywhere near your network address domestic.

  Computers (and the iPhone) which are only connected to the "visible" networks don't need to do.  They used scan, looking for those broadcast of the SSID, and then are alive when they find one they know.

  The iPhone is a phone, and he needs to save on battery life, so he cannot have the luxury of these packages to search daily for each hidden network, you connect to, so the problem of broadcasting.

  Take a look at this article From Microsoft TechNet for more information.

• Windows Vista Business ed. reformat - my computer detects the network but will not connect to Internet

  Can someone help me, I can't reformat a laptop compact with a windows vista Business edition OS. I was wondering if I could use the recovery partition or do I have to use an installation CD. And by the way, just to give you a head I'm just a beginner and badly needs help. the problem I had is I get a strong signal for my WiFi, but again it is not connect to the internet it connects sometimes but then after I reboot my phone it comes back with the same problem, it connects to the internet, but I detect my network, someone told me to just reformat the entire system. I hope someone can give me a help step by step on how to do it. and also I do not see the product key for my system. your help would be greatly appreciated thanks

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Formatting/reinstalling is overkill. A bit like buying a new car because you have a flat tire.

  To reinstall, you can use either the volume of recovery or the recovery disc, both should work pretty much the same. In general, the product key is located on the system like a sticker (on laptops usually on the bottom). If you can't find yours, you should contact the provider or your network administrator (and in fact, if there is a working system, you should contact them before doing anything).

  Before you do this right, you can try this: click Start and type CMD. Right click on the menu entry that appears and choose "Run as Administrator". Click on continue in the UAC prompt. From the command line, run:

  ipconfig/release

  ipconfig/flushdns

  ipconfig / renew

  Allow everyone to finish (return to the command line) before proceeding to the next. When you are finished, close the command prompt. See if that helps with your problems of connection.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org