Routing issue to site VPN site

Hello

I have a VPN site-to site of SR520 at SFsence VPN, the tunnel is up, but I can't ping internal addresses of these two paths of layout of the site terminate my default gateway. Help, please

Access list configuration:

access-list 100 permit ip 10.0.43.0 0.0.0.255 10.10.10.0 0.0.0.255

access-list 100 permit ip 10.10.10.0 0.0.0.255 10.0.43.0 0.0.0.255

IP nat inside source map route SHEEP interface Dialer 0 overload

access-list 110 deny ip 10.10.10.0 0.0.0.255 10.0.43.0 0.0.0.255

access-list 110 permit ip 10.10.10.0 0.0.0.255 any

SHEEP allowed 10 route map

corresponds to the IP 110

Note: remote site (SFsence) of 10.0.43.0/24

local site router Cisco SR520 10.10.10.0/29

Glad to know everything works now,

Please check the question as answered so future users can learn on this basis.

Kind regards

Tags: Cisco Security

cisco_asa_prob.jpg

Here the IP Configuration and the routing of the Barracuda firewall table:

screen_shot_2014-08 - 12_at_16.01.42.png

I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

Here is the config Cisco ASA:

 : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

Can someone please help me solve this problem?

When I tried to solve this I didn't choose which interface the Packet Tracer?

The interface inside or DMZ interface? Inside, he says it will not work with the dmz but the error did not help me

Anyone here knows why it does not work?

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Hello

Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

Route by tunnel watch also with 255 administrative distance. I've never used that in my scenarios... lets see...

Concerning

Knockaert

Why after connect to my router it take 1-2 minutes to load the router's Web site? No software and the hardware has changed.

Why after connect to my router it take 1-2 minutes to load the router's Web site? No software and the hardware has changed.

Hello

I suggest you check out the link to Linksys support:

http://homesupport.Cisco.com/en-us/support

Routing problem between the VPN Client and the router's Ethernet device

Hello

I have a Cisco 1721 in a test environment.

A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

The configuration was inspired form the sample Configuration

"Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

and the output of the ConfigMaker configuration.

Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

(customer has a correct route and return ICMP packets to the router).

The question now is:

How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

conf of the router is attached - hope that's not too...

Thanks & cordially

Thomas Schmidt

-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

!

version 12.2

horodateurs service debug uptime

Log service timestamps uptime

encryption password service

!

!

host name * moderator edit *.

!

enable secret 5 * moderator edit *.

!

!

AAA new-model

AAA authentication login userauthen local

AAA authorization groupauthor LAN

!

! only for the test...

!

username cisco password 0 * moderator edit *.

!

IP subnet zero

!

audit of IP notify Journal

Max-events of po verification IP 100

!

crypto ISAKMP policy 3

3des encryption

preshared authentication

Group 2

!

ISAKMP crypto client configuration group 3000client

key cisco123

pool ippool

!

! We do not want to divide the tunnel

! ACL 108

!

Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

!

Crypto-map dynamic dynmap 10

Set transform-set RIGHT

!

map clientmap client to authenticate crypto list userauthen

card crypto clientmap isakmp authorization list groupauthor

client configuration address map clientmap crypto answer

10 ipsec-isakmp crypto map clientmap Dynamics dynmap

!

interface Ethernet0

no downtime

Description connected to VPN

IP 192.168.1.1 255.255.255.0

full-duplex

IP access-group 101 in

IP access-group 101 out

KeepAlive 10

No cdp enable

!

interface Ethernet1

no downtime

address 192.168.3.1 IP 255.255.255.0

IP access-group 101 in

IP access-group 101 out

full-duplex

KeepAlive 10

No cdp enable

!

interface FastEthernet0

no downtime

Description connected to the Internet

IP 172.16.12.20 255.255.224.0

automatic speed

KeepAlive 10

No cdp enable

!

! This access group is also only for test cases!

!

no access list 101

access list 101 ip allow a whole

!

local pool IP 192.168.10.1 ippool 192.168.10.10

IP classless

IP route 0.0.0.0 0.0.0.0 172.16.12.20

enable IP pim Bennett

!

Line con 0

exec-timeout 0 0

password 7 * edit from moderator *.

line to 0

line vty 0 4

!

end

^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

Thomas,

Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

Kurtis Durrett

Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

Hello

Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

Please, what missing am me?

A few exits:

ISAKMP crypto to show her:

isakmp crypto #show her

IPv4 Crypto ISAKMP Security Association

DST CBC conn-State id

62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

IPv6 Crypto ISAKMP Security Association

Crypto ipsec to show her:

Interface: GigabitEthernet0/0

Tag crypto map: QRIOSMAP, local addr 62.173.32.122

protégé of the vrf: (none)

local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

current_peer 62.173.32.50 port 500

LICENCE, flags is {origin_is_acl},

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, #pkts compr. has failed: 0

#pkts not unpacked: 0, #pkts decompress failed: 0

Errors #send 0, #recv 0 errors

local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

current outbound SPI: 0x4D7E4817 (1300121623)

PFS (Y/N): Y, Diffie-Hellman group: group2

SAS of the esp on arrival:

SPI: 0xEACF9A (15388570)

transform: esp-3des esp-md5-hmac.

running parameters = {Tunnel}

Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

calendar of his: service life remaining (k/s) key: (4491222/1015)

Size IV: 8 bytes

support for replay detection: Y

Status: ACTIVE

Please see my config:

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

encryption... isakmp key address 62.X.X... 50

ISAKMP crypto keepalive 10 periodicals

!

!

Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

!

QRIOSMAP 10 ipsec-isakmp crypto map

peer 62.X.X set... 50

transformation-TS-QRIOS game

PFS group2 Set

match address 100

!

!

!

!

!

interface GigabitEthernet0/0

Description WAN CONNECTION

62.X.X IP... 124 255.255.255.248 secondary

62.X.X IP... 123 255.255.255.248 secondary

62.X.X IP... 122 255.255.255.248

NAT outside IP

IP virtual-reassembly in

automatic duplex

automatic speed

card crypto QRIOSMAP

!

interface GigabitEthernet0/0.2

!

interface GigabitEthernet0/1

LAN CONNECTION description $ES_LAN$

address 192.168.20.1 255.255.255.0

IP nat inside

IP virtual-reassembly in

automatic duplex

automatic speed

!

IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

IP nat inside source list 1 pool mypool overload

overload of IP nat inside source list 100 interface GigabitEthernet0/0

!

access-list 1 permit 192.168.20.0 0.0.0.255

access-list 2 allow 10.2.0.0 0.0.0.255

Note access-list 100 category QRIOSVPNTRAFFIC = 4

Note access-list 100 IPSec rule

access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

access-list 101 deny ip any any newspaper

access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 110 permit ip 192.168.20.0 0.0.0.255 any

!

!

!

!

sheep allowed 10 route map

corresponds to the IP 110

The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

Here are the things I see in your config

I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

IP route 0.0.0.0 0.0.0.0 62.X.X... 121

IP route 0.0.0.0 0.0.0.0 62.172.32.121

This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

IP route 10.2.0.0 255.255.255.0 192.168.20.2

In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

IP route 172.17.0.0 255.255.0.0 Tunnel20

IP route 172.17.2.0 255.255.255.0 Tunnel20

And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

IP route 172.18.0.0 255.255.0.0 Tunnel20

IP route 172.18.0.0 Tunnel20 255.255.255.252

HTH

Rick

routing of multiple site-2-site VPN gateways

I have a strange configuration and need help.

We have and ISP with a 29 network. We have connected the Ethernet transfer to a 2 layer equipment and connected one end to a Calyptix firewall and the other to our Cisco 2811.

the router has a default route that points to the Calyptix firewall.

Currently, the router also has a P2P T1 line at the corp office.

We would like to install a VPN site-to site of this router in the corp office and use P2P as the backup to local traffic, but everything else goes out the ASA.

I feel like I should be able to configure a tunnel between the two (branch and corp) public IP addresses, but I can't ping the public IP address of Corp. branch because it passes to the firewall (default route).

What Miss me?

I have attached a PDF file of the configuration of the network.

I tried to configure static routes

IP route 50.199.17.17 255.255.255.255 72.34.95.209

&

IP route 72.34.95.210 255.255.255.255 50.199.17.22

But this does not work, any ideas or suggestions?

Hi James,

1. Please check the traffic from 50.199.17.17 to 72.34.95.210 where he's going. Make an itinerary of track of 72.34.95.210 and check if it goes to 210 OR a.211 (capture the firewall), then to 210

Note: Maybe traffic flow return of 50.199.17.16--> Firewall (72.34.95.211)--> router based on your current configuration (maybe ISP force to go in this direction)

(2 Please check that you do not receive this route(50.199.17.16/29) P2P T1 somehow by a trace of 72.34.95.210 to 50.199.17.17.

3. check that you don't have any inbound ACL on both routers.

Please mark this message as correct if it works.

Client VPN router IOS, and site to site vpn

Hello

Im trying to configure a vpn client access to an ios router that already has a vpn site-to site running. I don't see how the two can run on the same router.

So I guess my question is is it possible? and if anyone has therefore had a config that they can share or a useful link.

IM using a router 800 series with 12.4 ios

Thank you very much

Colin
```
ReadersUK wrote:
Hi
Im trying to configure access for a vpn client to a ios router that already has a site to site vpn running. I cant see how both can be running on the same router.
So i guess my question is can this be done? and if so has anyone got a config they can share or a useful link.
im using a 800 series router with 12.4 ios
Many thanks
Colin
```
Colin

It can be done. Look at this config example that shows a router configured with a site to site VPN and client vpn - connection

https://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094685.shtml

Jon

Default route inside the tunnel VPN Site to site

We want to carry the default traffic within the site to site VPN tunnel, our goal is to route all traffic including default branch road and HO HO help branch for surfing the internet.

I have due to difficulties

1. cannot configure dynamic NAT for the router in the branch on the ASA HO, I know configuration for 8.2, but know not about 8.4

This is the configuration for the 8.2, if someone can translate to 8.4, which would be a great help

NAT (outside) 1 192.168.230.0

2. I do not know how to write the default route on the branch office router to send all traffic within the VPN tunnel

Hello

As I understand it then you want to route ALL traffic from the Remote Site to the Central Site and manage Internet traffic there.

I suppose you could define "interesting traffic" in configuring VPN L2L ACL / access-list in the following way

Branch router

extended IP access list

allow an ip

ASA central

ip access list allow one

The idea behind the type of ACL for the VPN L2L above configurations is that, for example, the branch office router has a rule that sets connection coming from the local LAN for 'any' destination address must be sent to the VPN L2L connection. So, it would be in such a way that all the traffic will be sent to the Central Site via VPN L2L.

I must say however, that the VPN router configurations side are not more familiar to me because I manage especially with ASA Firewall (and to some extent still PIX and FWSMs)

I guess that on the ASA Central you will PAT translation to "outside" so that the host can access the Internet?

You would probably do something like this

object-group network to REMOTE-SITE-PAT-SOURCE

network-object

interface of REMOTE-SITE-PAT-SOURCE dynamic NAT (outside, outside) after auto source

If you don't want to use the 'outside' IP address, then you will have to create a 'network of object' for address IP of PAT and use it in the line of NAT configuration above instead of "interface".

Alternate configuration might be

network of the REMOTE-SITE-PAT object

subnet

dynamic NAT interface (outdoors, outdoor)

You also need to enable

permit same-security-traffic intra-interface

To allow traffic to enter and exit the same interface on the ASA

All these answers are naturally suggestion on what you have to do. I don't know what kind of configurations you have right now.

Hope this helps in some way

-Jouni

Post edited by: Jouni Forss

Issue of ASA vpn site to site isakmp

Hello

He has been asked to configure on ASA a new vpn site-to-site. For that vpn should I put:

crypto isakmp identity address
crypto ISAKMP allow outside

.. the configuration of my identity crypto isakmp is automatic and isakmp crypto is not enabled on any interface. I love vpn with ike enabled on the external interface. My question is: why should I enable isakmp on the external interface and especially can create disturbances to ike vpn that are already in place?

By elsewhere-group or tunnel-group strategy, it was me asked to set up, the two do not have indication of ike. Never seen this kind of configuration before vpn, something new.

Thank you

Hi, Giuseppe.

The crypto isakmp command activate outside changed ikev1 crypto Enable outside in the new ASA versions you need not enable this.

There is also no need configure isakmp crypto identity address such that it is set to auto.

This command indicates that the tunnel would be negotiated on the basis of the IP address but since it is set to auto it on it own will therefore not need to specify this command.

Yes, you can create a new group policy group for this new tunnel and tunnel and there should be no impact on other tunnels of work.

Kind regards

Aditya

Please evaluate the useful messages and mark the correct answers.

Cisco router check ipsec site to site vpn tunnetl time?

I have a Cisco router that has a tunnel vpn to another depending on the location. Now, I want to check how long the VPN for up/construction. I know not if on the SAA, he has this 'sh l2l vpn-sessiondb' command that will allow me to view the tunnel for how long time. Don't seem to find the correct command for Cisco router. If you know the order let me know! Thank you.

Hello

I suppose there might be some differences between different platforms (except ASA) VPN or at least it seems to me

You can try the following command

View details remote crypto session

Partial output from one of our routers

Interface: Port-channel20

Profile:

Duration: 01:21:02

The session state: UP-ACTIVE

Hope this helps

-Jouni

Issue from site to site of SRP527w port forwarding

Hello

I have problem with setting up port forwarding on the VPN between two cisco 527w.

Scenario when we see a tunnel VPN from Site to Site between Site A and B; a printer behind Site B must be accessible using the IP WAN of A Site address.

Like the picture above:

-From site A, I am able to ping printer and printer access locally and via 120.146.x.x with port forwarding to installation on site has to the printer.

-From site B, I am able to ping A site gateway but not able to access the printer through 120.146.x.x. The printer can be access via 129.203.x.x if port forwarding is configured on the site B on the printer.

Cisco SRP 527w supports port forwarding via VPN site-to-site site A to site B printer?

Y at - it no suggest or another solution for this scenario?

Some help would be very appreciated.

Kind regards

Thai

Hi thai,

I'm not entirely sure - I think that an IOS based router, for example, the 800 series, you could do with proper setup.

I would say that remote access to a printer or a server like this is perhaps not the most secure solution however. A better approach would be to use a router that supports both a remote access VPN site. With this, you must be able to use a VPN client to access the site with the IP address static, then tunnel to the other site where the device is. You might consider the series RV of the device as well as IOS routers for that.

Kind regards

Andy

RVS4000 / WRVS4400 VPN routing issue.

I would like to simplify my installation a bit, but unfortunately I do not know how to do this.

I have a triangle of CSB RVS, 2 RVS4000, 1 WRVS4400 devices

each router has a VPN gateway to gateway with 2 others, to any one of the 3 sites, you can access resources on the other 2.

It also works well, if for some reason, one of the legs of the VPN breaks down, it passes through the other router. at least it seems to work that way when it is tested.

Now enter my problem. I have 2 laptops that go around, Mine and at the office. If any of these are off site and connect to a router via the QuickVPN client. they can see the resources on the router, to which they connect.

How would I be able to connect to the Router 1 and be able to access resources on other VPN routers ' ed?

It is not so much a problem on the router because it is on the QuickVPN. When you go to an IP address that is not on the local network from the router, the QuickVPN does not and it that the request is sent to the internet.

The only way to access the other site and resources would be to unplug the first router and connect to each other.

The router 851 and 871 VPN issues still

Main site

1 - all connectivity-all thin - Web - database-email Mail - Proxy - ETC.

2 - VPN Tunnel to the TOP

Remote sites

1 - VPN Tunnel to the TOP and tests

1 cannot ping the main location of the 192.168.0.X (Yes any IP address)

2 - could not get out to the Internet (GO HOLLOW PROXY SERVER 192.168.0.3 even if I could ping)

3 could connect to the database but crashes right after the login screen. Can ping the address of 192.168.0.11 to this fine location database but the connection hangs and does not

* HAND CONFIG

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

!

crypto ISAKMP policy 3

BA 3des

md5 hash

preshared authentication

Group 2

XXX address X.X.X.X isakmp encryption key

XXX address X.X.X.X isakmp encryption key

ISAKMP crypto keepalive 5 20

!

Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

!

bssn 10 ipsec-isakmp crypto map

Description VPN for PARK

defined peer X.X.X.X

Set transform-set RIGHT

match address 100

bssn 20 ipsec-isakmp crypto map

VPN for Corneilia description

defined peer X.X.X.X

Set transform-set RIGHT

match address 102

bssn 30 ipsec-isakmp crypto map

Description VPN to OAK

defined peer X.X.X.X

Set transform-set RIGHT

match address 103

bssn 40 ipsec-isakmp crypto map

Description VPN to Herbert George Wells

defined peer X.X.X.X

Set transform-set RIGHT

match address 104

interface FastEthernet4

WAN

IP address 216.x.x.x 255.255.255.128 secondary

IP 216.x.x.x 255.255.255.128.

no ip redirection

no ip unreachable

no ip proxy-arp

NAT outside IP

IP virtual-reassembly

route IP cache flow

automatic duplex

automatic speed

card crypto bssn

!

interface Vlan1

Entry door

IP 216.X.X.X 255.255.255.248 secondary

IP 192.168.0.11 255.255.255.0

no ip redirection

no ip unreachable

IP nat inside

IP virtual-reassembly

route IP cache flow

IP tcp adjust-mss 1452

!

IP classless

IP route 0.0.0.0 0.0.0.0 216.x.x.x.

!

IP nat inside source overload map route interface FastEthernet4 sheep

!

recording of debug trap

access-list 100 permit ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.6.0 0.0.0.255

access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255

access-list 101 deny ip 192.168.0.0 0.0.0.255 192.168.5.0 0.0.0.255

access-list 101 permit ip 192.168.0.0 0.0.0.255 any

access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.6.0 0.0.0.255

access-list 103 allow ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255

access-list 104. allow ip 192.168.0.0 0.0.0.255 192.168.5.0 0.0.0.255

not run cdp

sheep allowed 10 route map

corresponds to the IP 101

* REMOTE SITE

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

XXX address X.X.X.X isakmp encryption key

ISAKMP crypto keepalive 5 20

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

!

bssn 10 ipsec-isakmp crypto map

Connect to main BSSN description

defined peer X.X.X.X

Set transform-set RIGHT

match address 100

interface FastEthernet4

IP 216.X.X.X 255.255.255.224

NAT outside IP

IP virtual-reassembly

automatic duplex

automatic speed

card crypto bssn

!

interface Vlan1

Entry door

IP 192.168.1.2 255.255.255.0

IP directed broadcast to the

IP nat inside

IP virtual-reassembly

IP tcp adjust-mss 1452

!

IP classless

IP route 0.0.0.0 0.0.0.0 X.X.X.X

IP http server

local IP http authentication

IP http secure server

IP http timeout policy slowed down 60 life 86400 request 10000

IP nat inside source overload map route interface FastEthernet4 sheep

!

access-list 100 permit ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255

access-list 101 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255

access-list 101 permit ip 192.168.1.0 0.0.0.255 any

not run cdp

sheep allowed 10 route map

corresponds to the IP 101

Thank you

Laughing out loud

On the remote router access list 100 should look like:

access-list 100 permit ip 192.168.1.0 0.0.0.255 any

On the main router, the 100 access list should look like:

access-list 100 permit ip any 192.168.1.0 0.0.0.255

HTH,

Kind regards

Kamal

setting the time & date on the router or Web site atomic time (to synchronize times)

Is there a program that will perform the same function as this file control breaks:
NET TIME \\[local pc name or an ip] / set yes

But instead of the parameter to another pc on your network will put it to your router (Cisco Linksys WRT110 in my case) or an atomic clock Web site?

I know VB, I can write my a program to do? If so, what would be the code to remove this date & time of my router or a Web site?

Time Windows synchronizes on a time server NTP [S].

The sequence of commands that I used in the past (as admin) is:
NET time /setsntp:192.168.1.1
w32tm/config /update
w32tm/Resync /rediscover

Where "192.168.1.1" is replaced by the time server NTP which synchronize you to.
Not sure if the Linksys routers include a SNTP server.

Microsoft replacement instructions are here:

"How to configure a time server authoritative in Windows XP"
<>http://support.Microsoft.com/kb/314054 >
Jump to halfway down to the paragraph "the time service Configuration Windows to use an external time source.

HTH,
JW

Routing issue to site VPN site

Similar Questions

cisco_asa_prob.jpg

screen_shot_2014-08 - 12_at_16.01.42.png

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Maybe you are looking for