RV016 - Dual WAN & Secure connection problem

Similar Questions

• IPSEC VPN on the dual WAN links

  Here's my situation. I have two identical sites ASA 5505 and each has the dual wan/ISP connection and are set to resume using the sla monitor followed. I would like to create a vpn between these two sites that remains active regardless of what ISP link is online. Just make two crytpo card statements10 and a 20 inside each of the asa to each of the other ASA STATIC PUBLIC IP? It works or cause problems?

  Configuration of SITE B

  card crypto Cox_Primary_map 10 corresponds to the address Cox_Primary_cryptomap_10

  crypto Cox_Primary_map 10 peer 72.X.X.X card game<== primary="" static="" isp="" at="" site="">

  10 Cox_Primary_map transform-set ESP-3DES-SHA crypto card game

  card crypto Qwest_Backup_map 20 corresponds to the address Qwest_Backup_cryptomap_20

  crypto Qwest_Backup_map 20 peer 98.X.X.X card game<== backup="" static="" isp="" at="" site="">

  Qwest_Backup_map 20 transform-set ESP-3DES-SHA crypto card game

  tunnel-group 72.X.X.X type ipsec-l2l

  IPSec-attributes tunnel-group 72.X.X.X

  pre-shared-key adadsfasdf

  tunnel-group 98.X.X.X type ipsec-l2l
  IPSec-attributes tunnel-group 98.X.X.X

  pre-shared-key adadsfasdf

  Thank you

  Jesse,

  One of the solutions to your problem is to apply the same for both interfaces crypto card and have the two counterparts mentioned under a crypto map entry.

  Since you're using track/IP SLA to activate a single link to a single IP address of time will be answers.

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/C5.html#wp2278871

  Have several inputs card crypto with the same statement in game will cause problems.

  Hope that makes sense.

  Marcin

• I have a problem of "Secure connection failed", access to an HTTPS site.

  I have a problem of "Secure connection failed", access to an HTTPS site. It is of this type:

  Your certificate contains the same serial number for another certificate issued by the certification authority. Please get a new certificate containing a unique serial number.
  

  (Error code: sec_error_reused_issuer_and_serial)

  OK, I have not read the support article carefully enough - it even says that this dialogue cannot be exceeded by adding an exception.
  you are most likely right that this problem arises because the same cert is used for different sites. this support article describes a work around, but it is probable, not applicable to your situation, since you would also have to remove the certification authority and which would create all sorts of problems as your production site will tend to choose an a valid CA certificate.

  Please contact your IT department or the problem of certificate on two different servers or to allow you to run a version of portable firefox where you can mess with the certificate store and the authorities of trust in order to access the test server.

• Bug Safari: could not establish a secure connection &amp; search bar problem

  I'm hosting a server wiki on one of my macs and he got a self-signed certificate (the one generated by the server application). Since a few days ago (10.11.3 upgrade could be the culprit), Safari cannot establish a secure connection, no more. Oddly enough, this kind of coincide with the search box issue as well, which has been documented elsewhere.

  I checked, the certificate is marked as "always trust" in my keychain. I can access the wiki perfectly in Firefox for example.

  What a paradox, that I have to use third party software to access a software solution Apple...?

  Please let me know if you have had the same problems and if you managed to solve it.

  Thank you

  HE'S

  Hey! Take a look at this. This temporary has helped a number of users here. Over time, everything should be resolved then wait for a while.

  A possible solution to the problem of address bar: disable the Safari Suggestions

  If you have problems to open Web pages, take a look at these techniques proposed by Apple of troubleshooting.

  https://support.Apple.com/en-us/HT204098

  Go to the Safari menu (at the top right of your screen next to the Apple icon), choose 'Quit Safari'

  Press the "Shift" key and while holding this button on your unique keyboard, click the icon of Safari on your Dock.

  Open Safari - Preferences - Privacy - data to remove any Web site.

  Open the menu to go with the Option (Alt) key - library - key locate Safari folder and place it on your desktop. Restart your Mac, open Safari and delete the file from your desktop.

  Also, try the following steps:

  Restart your Mac.

  Try to start:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once your Mac boot, restart dhcpd as you usually do.

• I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  Hello

  If you have a Modem and a wireless router or a Modem/Router combination. Read its manual and configure the WAN for PPPOE port.

  http://www.ezlan.NET/PPPoE.html

• lrt224 dual wan router

  Hi im new in dual wan configuration. Help, please.
  Here is my problem

  1 dynamic globe telecom primary WAN
  WAN static pldt 2 telecom
  Link failover mode

  1 router is connect to lrt224 to serve wifi and my switch also plugin for wifi wireless
  1 cctv dvr connected to port 9000 webport lrt224 9100 with auto detection parameters parameters

  Now:
  Sometimes cctv camera released to public ip address when the wan2 switch but sometimes cannot show also
  All around, with 1 wan dynamic as primary

  Hi @engkanto.net,.

  I agree with the suggestions. It is best to connect the IP camera to one of the LRT224 router's Ethernet ports. Then you must configure the Port Forwarding or Port Address Translation If you have more than one camera using the same internal port.

  Thank you.

• RV82 Dual WAN and online banking. Packages of two IP addresses

  Hi all

  I have a set RV082 in place with two different ISPS (load balancing). Some time ago, users began to experience problems with online banking. It seems that the banking system set up more than a 'channel' to/from the end user and that bank systems won't accept that the packets come from 2 different public IP. I solved this by linking all HTTPS traffic to WAN1.

  Is this a good solution or is there a better way to deal with this? I'm afraid that it will be 'imbalance' my network as many services like Netflix and Youtube is HTTPS.

  Are there other services online that may have problems with a configuration of load balancing?

  If WAN1 breaks down. WAN2 will start HTTPS transport even if HTTPS is related to WAN1?

  I also have a similar problem with the router alert (goes to wrong ISP each time second), but this seems to be fixed in the latest firmware:
  "Authentication of email account is configurable for email alert".

  Thanks in advance

  Jone

  Hello James,

  Your solution is correct.  Certain types of secure connection HTTPS or SSH will not work if you keep changing IP address source, because it breaks the three-way handshake.  To avoid that you binding memorandum of installation you have.  You can do the same for all other traffic must always go out to a certain port WAN.

  If the WAN connection selected for protocol links to crashes, he switched to the other WAN until the connection retrieves.

  I have not seen too many online services that have problems with the load balancing is especially with secure connections, namely HTTPS.  I tried to access the HTTPS, Netflix, but I could never get an encrypted connection, but your best bet is to monitor and observe the network to see how it affects you.

  I mean the line you are citing has to do with the configuration of authentication to an SMTP server to send alerts by e-mail, rather than choose a port WAN to use, however if you protocol links SMTP to the WAN you would use that should no longer be a problem.

  Hope that helps,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• RV325: Port WAN 1 connected (inactive)

  I bought a router VPN/Firewall Cisco RV325 Gigabit Dual WAN a month or two ago I try to connect to an OTN Verizon FIOS box. For those who are not familiar with Verizon FIOS, ONTARIO (Optical Network Terminal) box is used with Verizon FIOS to convert optical signals into ip packets: basically fiber in-> IPV4/V6 packets out. I had connected it to an Apple Airport Extreme for about 3 months without problem. Recently, I bought the Dual WAN Gigabit VPN/Firewall Cisco RV325 router so I could move the Apple Airport Extreme on the floor.

  I plugged the ethernet cable out of the box of Verizon HAVE in the WAN1 (port 15) of the VPN/Firewall Cisco RV325 Gigabit Dual WAN router. When I click on the menu option 'System State' in the navigation on the left to the RV325, I see connected in green and (Inactive) in red for 1 WAN Port with 0.0.0.0 as the WAN IP address. I tried to disable the port WAN2, allowing the DMZ by deleting configurations VLAN without result. I also upgraded to the latest firmware, deactivation of NSD (Network Service detection) and by increasing the intervals for NSD does not.

  Are there additional parameters that I need to activate/change in order to bring the WAN1 port in service on the VPN/Firewall Cisco RV325 Gigabit Dual WAN router?

  Thanks in advance for your help,

  -Justin

  Have you did match the existing configuration of WAN (PPPoE, DHCP, IP static, whatever)?

• RV082, Dual Wan, VPN + protocol bindings

  Hi all

  I have this kind of Setup and I can't figure out how to think this router.

  My Installer uses Dual Wan load balancing mode. I only need one VPN tunnel. High availability is my concern.

  Site 1 has fiber and Cable

  Site 2A cable and FTTN

  Each ISP provides a static IP

  VPN works very well in the event of failure. I am always disappointed that it works in the case where a single primary WAN breaks, but is not operational if primary WAN on Site 1 stops at the same time secondary Site WAN 2 stops. It is very rare but can happen.

  In any case, my problems are where I need binding protocol to ensure secure WEB (https, banking, portal provider) sessions.

  I bind, at the least, port 443 to my primary WAN. In this way, I can access the Web sites and keep me logged.

  So, if I browse a HTTPS across the VPN server, binding protocol always attempts to pass port 443 by the WAN1. He will not even consider the VPN as a valid route first.

  (Maybe) can problem I reduce Hop Count for Site 2 less than 35?     P.S. I replaced the addresses I don't think they are relevant.

  Destination IP Subnet mask Default gateway Number of hops Interface

  ADDR network WAN2 255.255.255.252 * 0 eth2 WAN1 network addr 255.255.255.248 * 0 eth1 Site 2 255.255.255.0 Site 1 fiber Gateway 35 eth1 Site 1 255.255.255.0 * 0 eth0 by default 0.0.0.0 Site 1 fiber WAN1 15 eth1 by default 0.0.0.0 Site 1 cable WAN2 40 eth2 by default 0.0.0.0 Site 1 fiber WAN1 40 eth1

  Thank you all,

  Bruno

  I would like to conclude this is a bug and requires further investigation. I wouldn't call it a limitation if it was my decision (not that I have so much importance in this regard)

  -Tom
  Please mark replied messages useful

• Secure connection has no error - for almost all sites!

  Mozilla Firefox began vomiting following for almost all Internet sites error message I usually access!

  The error:

  The secure connection failed

  The connection to the server was reset while the page is loading.

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the web site owners to inform them of this problem.
  

  I use a laptop computer Lenovo z580 with Windows 7 Home Premium with Firefox installed 41.0.2.
  I checked the proxy settings, and they are the same in Firefox, like in other browsers (IE and Chrome).
  I checked the settings of the system time, and there is no problem there.

  I'm unable to download images for a reason, so I downloaded the images (of the error messages for different Web sites to http://s912.photobucket.com/user/sushd/library/Firefox

  Any help is appreciated.

  TIA

  Make a check of malware with several malware scanning of programs on the Windows computer.

  • https://support.Mozilla.org/KB/troubleshoot-Firefox-issues-caused-malware

  Please scan with all programs, because each program detects a different malicious program.
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender:
    http://Windows.Microsoft.com/en-us/Windows/using-Defender
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

• Beveiligde setting mislukt / Secure connection failed

  [NL] ALS ik sites als facebook.com en youtube.com wil openen squeeze fusion ik 'Beveiligde setting mislukt. " Op said hoe los ik? Andere websites als google.com, 9gag.com en instagram.com (eigenlijk alle andere site die ik heb round) doen het wel!

  [EN] When I opened sites like facebook.com and youtube.com , I get the message "secure connection failed". How to solve this problem? Other sites like google.com, 9gag.com , and instagram.com (basically every other site I tried) are doing well!

  What antivirus security software do you have?

  There are security software such as Avast and Kaspersky that intercepts secure connections and sends its own certificate.

  If you cannot inspect the certificate by "I understand the risks", then try this:

  Open the "Add Security Exception" this URL chrome by pasting into the address bar of Firefox and check the certificate:

  • chrome://pippki/content/exceptionDialog.XUL

  In the field of location of this window, type or paste the URL of the Web site.

  • retrieve the certificate via the button 'Get certificate '.
  • Click on the "view..." button. "to inspect the certificate in the certificate display

  You can check details such as the issuer and the certificate chain in the Details tab of the certificate display.
  Check which is the issuer of the certificate.
  If necessary, you can attach a screenshot that shows the display of the certificate.

• "Secure connection failed" that occur on the growth of number of sites, v40.0.2

  I'm on a Mac network and many of us become "secure connection failed: the page you are you are trying to view are not visible because the authenticity of the received data could not be verified." This number of sites displaying this error increases. It was just Wikipedia.org at the beginning, but now I can't access Mozilla.org! I have tried virtually all solutions that have worked for others, without success, including:

  -Uninstall of Firefox and install the 40.0.2 version

  -setting 'security.tls.version.fallback - limit' 0 or 1

  -setting in "security.tls.version.max" to 0 or 1

  -disable the 'security.ssl3.dhe_rsa_aes_128_sha' and 'security.ssl3.dhe_rsa_aes_256_sha '.

  -Uninstall and creating a profile

  -Check without plugins or add-ons are causing the problem

  -Refreshing Firefox

  And probably others I don't remember. I wish I could put more details browser, but can't because I can't get on Mozilla with Firefox. Please help and thank you very much!

  Which site gives you inappropriate alert rescue - the main www (https://www.mozilla.org/) or this support site? Or is this only a problem when you use a partial domain that redirects, such as https://mozilla.org/?

  Both this site and the www site use TLS 1.2, so Firefox does not need to return to TLS 1.0 in both cases. In addition, Firefox should have no problems connecting to Wikipedia.

  It seems that you do not have a direct connection, there is a proxy server or something else between you and the site or malware.

  If it's common throughout your network, it might be a common agent or something wrong with the router/firewall.

• Secure connection failed for Nginx + Comodo PossitiveSSL while SSLlabs Score is A +.

  I own the Web site https://vzinity.com that runs on Nginx and uses a Comodo PossitiveSSL cert.

  I tested the installation of SSL to https://www.ssllabs.com/ssltest/analyze.html?d=vzinity.com and it gets a grade of A +.

  I tried opening the site with many browsers, but I don't see this problem in Firefox. When I visit the website using Firefox 39 (Windows 7, Windows 8.1, 10 Windows and Linux Mint) I get the following error:

  The secure connection failed

  The connection to vzinity.com while the page is loading.

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the website owners to inform them of this problem.
  

  Any help will be appreciated.

  Thank you.

  That looks like a problem with bad sniffing user agent.

  It works for me if I change date 20100101 in Gecko/20100101 in on user agent (same Gecko/20100102 works, only Gecko/20100101 does not work).

  • Mozilla/5.0 (X 11; Linux i686; RV:39.0) Gecko/Firefox/39.0 39.0

  The server could be hacked to target only a Firefox user agent.
  You can contact the Web site and ask them to look into this.

• Get the error message after upgrade to Windows 10: peer certificate has no Secure Connection has an invalid signature.

  Error message trying to connect to Facebook after update to Windows 10: secure connection failed

  An error occurred during a connection to www.facebook.com. The peer certificate has an invalid signature. (Error code: sec_error_bad_signature)

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the website owners to inform them of this problem.
  

  Hey, if you're an avast user, please disable https scanning software:

  1. Open the Avast dashboard on an affected system.
  2. Select settings in the left side menu.
  3. Adopt a Protection Active.
  4. Click on customize next to the Web Shield.
  5. Uncheck the option "Enable HTTPS analysis", and then click ok.

  http://www.gHacks.NET/2014/10/31/avasts-HTTPS-scanning-interferes-with-Firefox-and-other-programs/

• Unable to connect to google after installing windows 10 "secure connection failed".

  I installed windows 10 today.

  now, every time that I can't get to google/youtube to firefox, internet explorer and opera.

  I get this error:

  "Secure connection failed".

  The connection on www.google.com while the page is loading.

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the website owners to inform them of this problem."
  

  I would appreciate help, google and youtube are rather important

  Sorry for the delay, long day away.

  With this many cross-browser issues, can you confirm that your system clock date, time, and time zone are all correct? SSL validity checks are time sensitive.

  If you see a globe, I think that you are unable to use an HTTPS address. Usually Firefox displays a padlock or a "!" icon in the shape of triangle on a HTTPS address depending on whether the certificate withdraws or has a problem.

  Is there a code in parentheses, separated by underscores in the error page? If so, could you copy and paste this code.