RV082 multiple subnet and DHCP
Hello
I want installation 2 lans in my RV082:
192.168.1.0
and
192.168.2.0
My question is what happends as DHCP?
I tested and it gives only IP via DHCP addresses in the 192.168.1.0 lan. What happens if I put a WRT54G2 DHCP service in the Lan 192.168.2.0 and connected to the RV082?
So, in this case the multiple subnet are useful?
Thank you very much
Oliver
In general: the RV082 is now part of Cisco Small Business, and you might want to ask your questions in the Cisco Business little community support for routers. You will find people from Cisco over there...
It is my understanding that the function of multiple routers RV LAN subnet extends the NAT tables. By default, the router of RV will be only NAT for source from inside the LAN IP subnet IP addresses. If your router is equipped with the 192.168.1.1/255.255.255.0 by default then it will be only to do NAT for 192.168.1. * IP address, but not others. If you connect a different LAN (for example, 192.168.2.0/255.255.255.0) subnet across another router (the one without NAT) to your RV then the different LAN subnet would no internet because the RV does not know the LAN subnet and it doesn't NAT. basically the RV would send source IP addresses * 192.168.2 unchanged in the internet where they would quickly disappear. The function of multiple subnet allows you to say the RV that 192.168.2.0/255.255.255.0 is actually a subnet of your local network, routed and is supposed to happen by NAT.
Tags: Linksys Routers
Similar Questions
-
Hello
The RV042G takes by acting as a DHCP server on several local networks virtual (or alone)?
Im going to set up three separate VLAN (no routing between the two) and want the router to provide addresses on all three VLAN (different subnets). The RV042G will do the job?
Appreciate any input
/ Claes
Paindivine,
Please refer to this previous post.
https://supportforums.Cisco.com/discussion/11576126/RV042-multiple-subnets
-
LRT224 Support for multiple subnets
I'm considering buying a LRT224, but need help with something.
The network that I have managed has about 200 aircraft currently, with mixed brands and types of switches, access points, etc., scattered. It is a small school that had a lot of different people by running, other not so good, other better. Now, I managed it.
We would like to add more devices, but currently we are limited to 254 devices. In the manual of LRT224, it - looks - like you can specify manually the subnet mask and the range of DHCP servers. For example, I could change the subnet mask 255.255.252.0 or one 22 subnet, and then specify the range being DHCP, for example 192.168.1.2 alone, through 192.168.4.254, for 1024 addresses total? I want to do this without using VLANs, because I'm not sure if any of the switches support VLAN tagging, and I have no experience with the VLAN.
Let me know, thanks!
IPsec VPN site to site, LRT224 tunnels supports greater than 255.255.255.0 subnet masks. However the subnets the side LAN of LRT224 are limited to a class C subnet by VLAN.
-
Hi all
I'm having a bit of difficulty up a SG300 - 28 p to L3 and DHCP. I will attach a basic network diagram and a very short list of my needs.
I'm building a temporary network for a company event 1 day that I can't make it work in our office "Lab".
L3 - SG300 - 28 p connects to our provider using a connection of the SFP.
I have to be able to address IP DHCP 300 + using the SG300 - 28 p
My problem is that I can ping my 2 machines test (manually configured IP) about 172.16.0.3 and 172.16.0.4, but cannot ping after the (internet) referral. Also DHCP distributes no intellectual property for the range 172.16.0.10 - 172.16.1.200
VLAN 1 is set to 10.2.2.20 access port (to the provider through a connection on port 28 FPS)
VLAN 100 is 172.16.0.2 access port (ports 1-26)
I have the WLC and WAP tri...
Is the set of even possible? I know that the EQ network is a bit budget for users, but for a one day business event I just do not have a budget for the purchase of switches better.
Please excuse the gross chart.
Thank you in advance.
-RJ
Thanks for the reply.
With the information that you have provided, it seems the only part missing is the way return the unit for service providers. Unfortunately there is no way around that, and no, you will not be able to put anything between the two, because the device doing the NATting is unity of suppliers.
I think that what is happening is that traffic is actually the side provider, but there is no way to do so as soon as the provider is not a route for the subnet in 172.16.x.x.
Out of curiosity, why do you use a VLAN for the devices connected to the SG300? Could you use the 10 subnet Ip addresses? If you do this, you will not need to have a route back from the supplier, as all devices will be on the same subnet.
-
Series of unmanaged switches 100 and DHCP
Hi all, we have a router RV082 switch 8 ethernet ports, it is actually 8 lan with a DHCP address assignment devices (router is used as switch/router and DHCP server).
Now we need to increase the number of attached LAN devices (other pc, printers, etc.), and we think buy Cisco 100 ethernet switch Series 16 or 24 ports to connect to RV082.
In this case RV082 will be able to assign DHCP addresses for devices connected to the eth switch ports?
Thanks in advance.
Hi Loris, yes it is not a problem. You should be able to switch on a lan port, connect computers to the switch and things should be OK.
-Tom
Please mark replied messages useful -
SGE2010 - traffic relay and DHCP configuration
Hei
We bought just a switch SGE2010 we want to use to replace the switches in the control panel of our office. So far I managed to access the switch and assigned a static ip.adress on our net, but I can't get to our entry point switch relay traffic. I have a test machine that is configured with a static IP as well and tried the ok sign, but as soon as I put the switch between traffic is not relayed.
The idea was to use this switch as a DHCP as well. But I thought it would be a start to get at least the traffic relayed before starting the dhcp part.
Only configuration settings I have done factory settings are the following: (note that the IP is slightly adjusted, but consistent for reasons of confidentiality)
Configuration of the IP4
- Assigned to a static ip address: 95.59.69.148
- Assigned a subpattern: 255.255.255.192
- Assigned to a user-defined gateway: 95.59.69.129
DNS configuration
- Assigned to an ip address dns address: active 95.59.0.100
- Assigned to a dns ip address: 95.59.0.200
All these settings are the default settings that we use when we assign a server with a static ip address, so it is not a pick up of our filtration dhcp server. So my main question is why on earth isn't it relay traffic?
In addition, we are interested to kill the former (with stones, I hope) dhcp server and dhcp on the sge2010 configuration. The current dhcp is an operating system. X dhcp server (Yes a mac) with the following configuration:
- (Dynamic ip) subnet
From ip: 95.59.69.179
Ending ip: 95.59.69.190
Subnet: 255.255.255.192 - Router ip: 95.59.69.129
Rental time: 3 hours - The range 95.59.69.130 to 95.59.69.149 we set up manually on the servers, hardware, etc.
- DNS server: 95.59.0.100 & 95.59.0.200
Default search domain: No. - dns - available.example.com - And then we have a group of static mappings to Mac-addresses
ip address: 95.59.69.150
IP: 95.59.69.178
I tried to see in the configuration where I could the mappings static spesify range etc, but I can't say it got me anywhere. So my second question is how to install a server dhcp of Eric as a designated above?
It's nice to finally convince the CEO to move the dhcp to a better metal, but it's not as nice having a hard time setting up. I would apprecitate every possible leeds and suggestions since I'm kinda stuck.
Thanks in advance
Rafn.R
Hello
My SGE2000P forwards DHCP requests on my DHCP server.
I used my default VLAN1 as an interface routed to unicast request DHCP relay on my server (router ISR UC520) that resides on that VLAN 1.
My interface Vlan 1 on my SGE2000P has an IP 192.168.10.254.
My gateway address for potential hosts in VLAN 2 IP will be the ADDRESS IP I AI ASSIGNES to VLAN 2, because the PC or the IP hosts connected to VLAN2 will use IP VLAN2 interface as the gateway. It's just how it works!
Hosts of PC on VLAN 2 need of a default route and they use the IP I assigned to VLAN2 as their next jump out VLAN2 on the real world.
This address can be seen below.
DHCP relay is enabled with the option 82
I chose VLAN2 as an interface VLAN, as shown below.
I have two ports not signposted in the VLAN2, and I joined an IP host to G1 so that I can test the DHCP relay.
I get the following debug output from my dhcp server, so I know the relay is working.
002624: 19:40:08.575 Dec 5: DHCPD: looking for expiry of the leases.
002625: 19:40:58.408 Dec 5: DHCPD: DISCOVER notification to:
002626: 19:40:58.408 Dec 5: DHCPD: htype 1 CHADRR 0025.84d8.d008
002627: 19:40:58.408 Dec 5: DHCPD: id remote 020a0000c0a80a0101080001
002628: 19:40:58.408 Dec 5: DHCPD: id circuit 00000000
002629: 19:40:58.408 Dec 5: DHCPD: see if there is a specified internal pool class:
But I must confess that I have opened a case on it with the Small Business Support Center, because I think I can see something wrong on my DHCP server debugging.
But the key is that I see the router WAN/DHCP server, see the query from DHCP.
The only way to the broadcast DHCP requests can get to the DHCP server, if the switch SGE2000P takes these DHCP broadcast requests and unicast these or relay to my server DHCP IP address 192.168.10.1.
So in other words he tries to relay DHCP.
I would ask you to please check the SGE2010 Administrator's guide because it clearly shows how to configure the DHCP on the SGE2010 relay.
Even if the screen capture shows and the old version of the code below. I have day my SGE2000P tonight at the generally available (GA) version of the code.
Just outa interest, if you telnet to the switch, is your mode of layer 3 or Layer 2 switch.
I can also say from your screenshot that your uplink ports are in overlay mode.
Maybe if you don't use stacking, you can set your switch to the layer 3 mode and standalone mode
Best regards, Dave
-
Cisco ASA 5505 site for multiple subnet of the site.
Hello. I need help to configure my cisco asa 5505.
I set up a VPN between two ASA 5505 tunnel
Site 1:
Subnet 192.168.77.0
Site 2:
Have multiple VLANs and now the tunnel goes to vlan400 - 192.168.1.0
What I need help:
Site 1, I need to be able to reach a different virtual LAN on site 2. vlan480 - 192.168.20.0
And 1 site I have to reach 192.168.77.0 subnet of vlan480 - 192.168.20.0
Vlan480 is used for phones. In vlan480, we have a PABX.
Is this possible to do?
Any help would be much appreciated!
Config site 2:
: Saved
:
ASA Version 7.2 (2)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
names of
name 192.168.1.250 DomeneServer
name of 192.168.1.10 NotesServer
name 192.168.1.90 Steadyily
name 192.168.1.97 TerminalServer
name 192.168.1.98 eyeshare w8
name 192.168.50.10 w8-print
name 192.168.1.94 w8 - app
name 192.168.1.89 FonnaFlyMedia
!
interface Vlan1
nameif Vlan1
security-level 100
IP 192.168.200.100 255.255.255.0
OSPF cost 10
!
interface Vlan2
nameif outside
security-level 0
IP address 79.x.x.226 255.255.255.224
OSPF cost 10
!
interface Vlan400
nameif vlan400
security-level 100
IP 192.168.1.1 255.255.255.0
OSPF cost 10
!
interface Vlan450
nameif Vlan450
security-level 100
IP 192.168.210.1 255.255.255.0
OSPF cost 10
!
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
IP 192.168.2.1 255.255.255.0
OSPF cost 10
!
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
address 192.168.3.1 IP 255.255.255.0
OSPF cost 10
!
interface Vlan462
Vlan462-Suldalsposten nameif
security-level 100
192.168.4.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
IP 192.168.202.1 255.255.255.0
OSPF cost 10
!
interface Vlan480
nameif vlan480 Telefoni
security-level 100
address 192.168.20.1 255.255.255.0
OSPF cost 10
!
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
IP 192.168.10.1 255.255.255.0
OSPF cost 10
!
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
192.168.30.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan510
Vlan510-IsTak nameif
security-level 100
192.168.40.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
192.168.50.1 IP address 255.255.255.0
OSPF cost 10
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 490
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd encrypted x
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain default.domain.invalid
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
Lotus_Notes_Utgaaande tcp service object-group
UT og Frim Notes Description til alle
area of port-object eq
port-object eq ftp
port-object eq www
EQ object of the https port
port-object eq lotusnotes
EQ Port pop3 object
EQ pptp Port object
EQ smtp port object
Lotus_Notes_inn tcp service object-group
Description of the inn og alle til Notes
port-object eq www
port-object eq lotusnotes
EQ Port pop3 object
EQ smtp port object
object-group service Reisebyraa tcp - udp
3702 3702 object-port Beach
5500 5500 object-port Beach
range of object-port 9876 9876
object-group service Remote_Desktop tcp - udp
Description Tilgang til Remote Desktop
3389 3389 port-object range
object-group service Sand_Servicenter_50000 tcp - udp
Description program tilgang til sand service AS
object-port range 50000 50000
VNC_Remote_Admin tcp service object-group
Description Fra ¥ oss til alle
5900 5900 port-object range
object-group service Printer_Accept tcp - udp
9100 9100 port-object range
port-object eq echo
ICMP-type of object-group Echo_Ping
echo ICMP-object
response to echo ICMP-object
object-group service Print tcp
9100 9100 port-object range
FTP_NADA tcp service object-group
Suldalsposten NADA tilgang description
port-object eq ftp
port-object eq ftp - data
Telefonsentral tcp service object-group
Hoftun description
port-object eq ftp
port-object eq ftp - data
port-object eq www
EQ object of the https port
port-object eq telnet
Printer_inn_800 tcp service object-group
Fra 800 thought-out og inn til 400 port 7777 description
range of object-port 7777 7777
Suldalsposten tcp service object-group
Description send av mail hav Mac Mail at - Ã ¥ nrep smtp
EQ Port pop3 object
EQ smtp port object
http2 tcp service object-group
Beach of port-object 81 81
object-group service DMZ_FTP_PASSIVE tcp - udp
55536 56559 object-port Beach
object-group service DMZ_FTP tcp - udp
20 21 object-port Beach
object-group service DMZ_HTTPS tcp - udp
Beach of port-object 443 443
object-group service DMZ_HTTP tcp - udp
8080 8080 port-object range
DNS_Query tcp service object-group
of domain object from the beach
object-group service DUETT_SQL_PORT tcp - udp
Description for a mellom andre og duett Server nett
54659 54659 object-port Beach
outside_access_in of access allowed any ip an extended list
outside_access_out of access allowed any ip an extended list
vlan400_access_in list extended access deny ip any host 149.20.56.34
vlan400_access_in list extended access deny ip any host 149.20.56.32
vlan400_access_in of access allowed any ip an extended list
Vlan450_access_in list extended access deny ip any host 149.20.56.34
Vlan450_access_in list extended access deny ip any host 149.20.56.32
Vlan450_access_in of access allowed any ip an extended list
Vlan460_access_in list extended access deny ip any host 149.20.56.34
Vlan460_access_in list extended access deny ip any host 149.20.56.32
Vlan460_access_in of access allowed any ip an extended list
vlan400_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
vlan400_access_out list extended access permit tcp any host DomeneServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host TerminalServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host http2 object-group Steadyily
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_inn
vlan400_access_out list extended access permit tcp any host NotesServer object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8-eyeshare object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8 - app object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host FonnaFlyMedia range 8400-8600
vlan400_access_out list extended access permit udp any host FonnaFlyMedia 9000 9001 range
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host DomeneServer
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host w8 - app object-group DUETT_SQL_PORT
Vlan500_access_in list extended access deny ip any host 149.20.56.34
Vlan500_access_in list extended access deny ip any host 149.20.56.32
Vlan500_access_in of access allowed any ip an extended list
vlan470_access_in list extended access deny ip any host 149.20.56.34
vlan470_access_in list extended access deny ip any host 149.20.56.32
vlan470_access_in of access allowed any ip an extended list
Vlan490_access_in list extended access deny ip any host 149.20.56.34
Vlan490_access_in list extended access deny ip any host 149.20.56.32
Vlan490_access_in of access allowed any ip an extended list
Vlan450_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan1_access_out of access allowed any ip an extended list
Vlan1_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan1_access_out deny ip extended access list a whole
Vlan1_access_out list extended access permit icmp any any echo response
Vlan460_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTP
Vlan500_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit tcp any host 192.168.202.10 - group Remote_Desktop object
Vlan510_access_out list extended access permit icmp any any Echo_Ping object-group
vlan480_access_out of access allowed any ip an extended list
Vlan510_access_in of access allowed any ip an extended list
Vlan600_access_in of access allowed any ip an extended list
Vlan600_access_out list extended access permit icmp any one
Vlan600_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan600_access_out list extended access permitted tcp 192.168.1.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.202.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.210.0 255.255.255.0 host w8-printing eq www
Vlan600_access_in_1 of access allowed any ip an extended list
Vlan461_access_in of access allowed any ip an extended list
Vlan461_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended ip allowed any one
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_in_1 extended ip allowed any one
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Vlan1
Outside 1500 MTU
vlan400 MTU 1500
MTU 1500 Vlan450
MTU 1500 Vlan460-SuldalHotell
MTU 1500 Vlan461-SuldalHotellGjest
vlan470-Kyrkjekontoret MTU 1500
MTU 1500 vlan480-Telefoni
MTU 1500 Vlan490-QNapBackup
MTU 1500 Vlan500-HellandBadlands
MTU 1500 Vlan510-IsTak
MTU 1500 Vlan600-SafeQ
MTU 1500 Vlan462-Suldalsposten
no failover
Monitor-interface Vlan1
interface of the monitor to the outside
the interface of the monitor vlan400
the interface of the monitor Vlan450
the interface of the Vlan460-SuldalHotell monitor
the interface of the Vlan461-SuldalHotellGjest monitor
the interface of the vlan470-Kyrkjekontoret monitor
Monitor-interface vlan480-Telefoni
the interface of the Vlan490-QNapBackup monitor
the interface of the Vlan500-HellandBadlands monitor
Monitor-interface Vlan510-IsTak
Monitor-interface Vlan600-SafeQ
the interface of the monitor Vlan462-Suldalsposten
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
vlan400_nat0_outbound (vlan400) NAT 0 access list
NAT (vlan400) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan450) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
NAT (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
NAT (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
NAT (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
NAT (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
NAT (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
NAT (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400, external) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret, external) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400, external) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400, external) 79.x.x.231 netmask 255.255.255.255 TerminalServer
static (vlan400, external) 79.x.x.234 Steadyily netmask 255.255.255.255
static (vlan400, outside) w8-eyeshare netmask 255.255.255.255 79.x.x.232
static (Vlan490-QNapBackup, external) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ, external) 79.x.x.235 w8 - print subnet mask 255.255.255.255
static (vlan400, outside) w8 - app netmask 255.255.255.255 79.x.x.236
static (Vlan450, vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
(Vlan500-HellandBadlands, vlan400) static 192.168.30.0 192.168.30.0 netmask 255.255.255.0
(vlan400, Vlan500-HellandBadlands) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
(vlan400, Vlan450) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, external) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten, vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400, Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450, Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret, Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
Access-group interface Vlan1 Vlan1_access_out
Access-group outside_access_in in interface outside
Access-group outside_access_out outside interface
Access-group vlan400_access_in in the vlan400 interface
vlan400_access_out group access to the interface vlan400
Access-group Vlan450_access_in in the Vlan450 interface
Access-group interface Vlan450 Vlan450_access_out
Access-group interface Vlan460-SuldalHotell Vlan460_access_in
Access-group interface Vlan460-SuldalHotell Vlan460_access_out
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_in
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_out
Access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
vlan470_access_out access to the interface vlan470-Kyrkjekontoret group
access to the interface vlan480-Telefoni, vlan480_access_out group
Access-group interface Vlan490-QNapBackup Vlan490_access_in
Access-group interface Vlan490-QNapBackup Vlan490_access_out
Access-group interface Vlan500-HellandBadlands Vlan500_access_in
Access-group interface Vlan500-HellandBadlands Vlan500_access_out
Access-group interface Vlan510-IsTak Vlan510_access_in
Access-group interface Vlan510-IsTak Vlan510_access_out
Access-group Vlan600_access_in_1 interface Vlan600-SafeQ
Access-group Vlan600_access_out interface Vlan600-SafeQ
Access-group Vlan462-Suldalsposten_access_in_1 Vlan462-Suldalsposten interface
Access-group Vlan462-Suldalsposten_access_out_1 Vlan462-Suldalsposten interface
Route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
x x encrypted privilege 15 password username
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
No snmp server location
No snmp Server contact
SNMP-Server Community public
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 20 match address outside_20_cryptomap_1
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 62.92.159.137
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
ISAKMP crypto enable vlan400
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 62.92.159.137 type ipsec-l2l
IPSec-attributes tunnel-group 62.92.159.137
pre-shared-key *.
Telnet 192.168.200.0 255.255.255.0 Vlan1
Telnet 192.168.1.0 255.255.255.0 vlan400
Telnet timeout 5
SSH 171.68.225.216 255.255.255.255 outside
SSH timeout 5
Console timeout 0
dhcpd update dns both
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 outside interface
!
dhcpd address 192.168.1.100 - 192.168.1.225 vlan400
dhcpd option ip 6 DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
vlan400 enable dhcpd
!
dhcpd address 192.168.210.100 - 192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd ip interface 192.168.210.1 option 3 Vlan450
enable Vlan450 dhcpd
!
dhcpd address 192.168.2.100 - 192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd 192.168.2.1 ip interface option 3 Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
!
dhcpd address 192.168.3.100 - 192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd ip interface 192.168.3.1 option 3 Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
!
dhcpd address 192.168.202.100 - 192.168.202.199 vlan470-Kyrkjekontoret
interface of dhcpd option 3 ip 192.168.202.1 vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
!
dhcpd option 3 192.168.20.1 ip interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
!
dhcpd address 192.168.10.80 - 192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd 192.168.10.1 ip interface option 3 Vlan490-QNapBackup
!
dhcpd address 192.168.30.100 - 192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd ip interface 192.168.30.1 option 3 Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
!
dhcpd address 192.168.40.100 - 192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd 3 ip Vlan510-IsTak 192.168.40.1 option interface
Vlan510-IsTak enable dhcpd
!
dhcpd address 192.168.50.150 - 192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
Vlan600-SafeQ enable dhcpd
!
dhcpd address 192.168.4.100 - 192.168.4.150 Vlan462-Suldalsposten
interface option 6 ip DomeneServer 81.167.36.11 Vlan462-Suldalsposten dhcpd
interface ip dhcpd option 3 Vlan462-Suldalsposten 192.168.4.1
Vlan462-Suldalsposten enable dhcpd
!
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
!
context of prompt hostname
Cryptochecksum:x
: end
Site 1 config:
: Saved
:
ASA Version 7.2 (4)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
passwd encrypted x
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.77.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
PPPoE Telenor customer vpdn group
IP address pppoe setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 15
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
DNS server-group DefaultDNS
domain default.domain.invalid
outside_access_in list extended access permit icmp any any disable log echo-reply
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
Enable http server
http 192.168.77.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 79.160.252.226
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.77.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group Telenor request dialout pppoe
VPDN group Telenor localname x
VPDN group Telenor ppp authentication chap
VPDN x x local store password username
dhcpd outside auto_config
!
dhcpd address 192.168.77.100 - 192.168.77.130 inside
dhcpd dns 192.168.77.1 on the inside interface
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
dhcpd allow inside
!
dhcpd option 6 ip 130.67.15.198 193.213.112.4 outside interface
!
tunnel-group 79.160.252.226 type ipsec-l2l
IPSec-attributes tunnel-group 79.160.252.226
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:x
: end
Hello
The addition of a new network to the existing VPN L2L should be a fairly simple process.
Essentially, you need to add the network of the Crypto present ACL configurations "crypto map" . You also need to configure the NAT0 configuration for it in the appropriate interfaces of the SAA. These configurations are all made on both ends of the VPN L2L connection.
Looking at your configurations above it would appear that you need to the following configurations
SITE 1
- We add the new network at the same time the crypto ACL and ACL NAT0
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.20.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.20.0 255.255.255.0
SITE 2
- We add new ACL crypto network
- We create a new NAT0 configuration for interface Vlan480 because there is no previous NAT0 configuration
outside_20_cryptomap_1 to access extended list ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
Comment by VLAN480-NAT0 NAT0 for VPN access-list
access-list VLAN480-NAT0 ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
NAT 0 access-list VLAN480-NAT0 (vlan480-Telefoni)
These configurations should pretty much do the trick.
Let me know if it worked
-Jouni
-
Using Cisco AP as router and DHCP server
I'm a newbie in the technology of Cisco wireless. I have a lot of Cisco wireless access point. One of them (1142AG-K9 Cisco) I want to set them up as a DHCP server and will forward traffic to the public ip address as it will route the traffic to 203.82.203.50 (Ip provided by ISP) and will lease ip as associated devices 192.168.10.0 pool.
Even though I know that it is possible using a router on the AP. But it is possible using a single access point?
If so, how?
Help, please.
Hi, the AP cisco are just basic layer 2 devices such as a hub or Layer 2 switch, it does not any layer 3 as a wireless router.
The Cisco access point supports to have a VLAN or subnet configured or more VLANS or subnets and will pass all traffic to a layer 3 devic so that traffic can be routed to the need.
The Ap can't stand to have an addrees ip configured on the bvi1 for the management.
Also the build in the ap dhcp option is very limited and will only know the ip address to wirless clints that connect to it on an ssid linked to its management interface in this case that the bvi1 and all them VLAN othe or subnets shall not use an external dhcp server.
Sent by Cisco Support technique iPhone App
-
How to send an email to multiple recipients and keep the list future emails?
How can I send an email to multiple recipients and store the names of future emails?
Are you using an e-mail application to send and receive your emails?
-
I added the NewtabUrl 2.2.3 extension while I entered in google when you open a new window and it worked. I updated firefox and now when I open a new tab I get multiple windows and I have to click on the window of google again to see just google so 2 clicks instead of one--I use it very often.
I don't see any obvious setting in the addon/extension or general settings.
Hello, firefox has added its own page of the new tab with the release of firefox 13 (for more information, see customize the page new tab), he has probably replaced the newtaburl parameters. You can try reinstalling the NewtabUrl 2.2.3 extension and put your new custom tab page.
or you can remove the extension and manually set your new tab page: enter Subject: config in the address bar (you will need to confirm the notification), search for the preference named browser.newtab.url, double-click it and change its value to www.google.com or page of your taste. -
This has just begun. When I close firefox it tells me that I am closing multiple tabs. and will not let me save them. the only option is to cancel or OK. When I say OK and restart Firefox all my tabs go :-( This happens every time now. I know how to recover my old tabs but whenever I close Firefox it always warns me that I'm closing multiple tabs.
Tanks for help getting Firefox working properly again
JimDo not use 'Clear history of Firefox closing' to clear the 'browsing history '.
- Tools > Options > Privacy: history: [X] clear history of Firefox closing > settings
- https://support.Mozilla.org/KB/clear+recent+history
Using the "Show my windows and tabs from last time" is a more reliable way to restore the session data.
- Tools > Options > general > startup: "When Firefox starts": "show my windows and tabs from last time '.
-
Can bookmarks be portable to multiple computers? Is it an option to connect and use my favorites with multiple computers and locations? Thank you
-
Why my photo album create multiple folders and duplicate my photos in folders?
Why my photo album create multiple folders and duplicate my photos in folders?
Can you give us more details about your problem? When this happens? It's an update of iOS for a newer version?
-
Requirement of DNS and DHCP Server Essentials 2012 home
I have a Server Windows Essentials 2012 acting as DNS and DHCP server with a domain name for backups etc on my home network. It's that everything works fine, no errors, no problem. Works well actually, telling me when the children did not install updates or restarted.
I have two groups of users. My sons step, 10 and 12, which I want to use OpenDNS as a provider external DNS with a policy very, very limited and my wife and me who want to use indications of root or Google DNS or any other DNS provider. Others, specific devices no user (box of the xBox, WII, Satellite, TV, CCTV etc.) can use.
Before the 2012 server, I had a 2 k 3 server running in a virtual machine for DHCP, alone and put my wife and my devices on static reservations with the just and external DNS provider used OpenDNS as the default scope, DNS. Unfortunately different bits of domain services 2012 don't seem to work unless the server of 2012 is the first DNS server listed on client machines (backups failed. Impossible to find other local computers). Currently, this means that we are all using OpenDNS.
What I would like is a way to say 2012 to send adult group DNS queries to another DNS provider and leave the rest at default to OpenDNS, while still having them register in the original DNS domain. Any suggestions?
This issue is beyond the scope of this site and must be placed on Technet or MSDN -
Target subnet mask and the gateway in different subnets and clock error
Hi all:
Need help. I have a standalone PC operating a direct VI on a CFP with a crossover ethernet cable (developed on my laptop, compiled and installed as a standalone on the PC). When the VI runs on standalone PC version, everything works (click the button, analyzers are read), but the time being pulled from the CFP is wrong, and infact resets to December 1969, a default value. I am error checking, and no error is marked with the CFP, slaughter programmes. When I go to the MAX function, the time playing of the CFP is the funky time. Looking at the IP addresses, I generally use a very standard protocol (192.168.000.001 for the PC, 192.168.000.002 for the CFP currently running on the subnet for the pc and the PSC 255.255.255.000). However, when I apply this Protocol on the CFP through max, it gives the error "the subnet mask you entered puts the target and the entry door to different subnets." I am not versed enough well understand this, and what I read in 2 postings here, I tried to harmonize the IP numbers and the subnet, and they do not seem to help. When I put intentionally in false numbers IP or subnet default time synchronization time correct (pc), but functions block (as expected). It is certainly not an issue of PC zone.
Anyone can offer any guidance?
Currently runnig LV 8.2 with drivers of 2009. PSC 1804 with MAX 4.6.
I appreciate all help.
Best regards;
GIS.
OK, I solved it. FYI: for those who are not aware of the IP: IP of the host and default gateway server to the same value. My work for the host computer are 192.168.000.001 and subnet masks can stay 255.255.255.000. The CFP has been set to 198.162.000.002 with a 90.00.00.03 DNS. Time server has been blocked by the Norton 2009 Firewall (even with an exception) and thus the cruxt of this issue together. I had to uninstall completely from this "software". I hope this helps.
Maybe you are looking for
-
new password back to the old password by itself?
Windows Vista Home Premium 64-bit... I changed my administrator password and it will work very well for a few hours a day, then, I'll try and log and the new password does not work, but the old one will! BY ITSELF?
-
I would like to change my Windows XP to linux-ubuntu, how
I would like to change my windows xp pro for linux-ubuntu how to please
-
Critical error: hearts When I play the game hearts, I now get a critical error. This only happens with this game. The error is: "the system has run out of memory." Try closing some applications and try again. "I have no other applications open. "Anyo
-
what the * arrived with the activation on my netbook number I improve it with a windows 7 pro disc and he tell me that I can't use this product key on this computer. can you tell me what the problem with it.
-
Problem by dragging the PS window to the 2nd screen/monitor
I have a MacBook Pro which is 10.10.5 and Yosemite. I have a 2nd monitor is an ASUS. I had been their mirror so far, but due to calibration problems, I do is no longer that. How can I drag Photoshop CC on the 2nd monitor? I have my put monitors i