S3-391 Acer wireless network adapter does not work after driver update

Similar Questions

• Wireless network adapter does not work on my Satellite A200

  Hello

  My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

  What can I do?

  Details:
  Typ: Atheros AR5008X Version: 7.2.0.164
  Laptop Satellite 200
  PSAE6E

  Please help me!
  Thanks in advance!

  Phil

  BIOS bug? I don t think so

  First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

  After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

  I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

• Update my wireless network device does not work after installation of Software Distribution Service 3.0

  After the installation of Software Distribution Service 3.0 update my wireless network camera does not work how do I uninstall Software Distribution Service 3.0

  How did you receive the update?

  Was it via Windows Update or Microsoft Update?

  Before the changes are made to your computer, the system restore points are made. This is so that you can go back in case an update causes problems.

  Follow these steps:

  1. click on the Start button

  2. click on accessories

  3. click on system tools

  4. click on system restore

  5. click on next

  6. in the calendar that appears, select the one which refers to Software Distribution Service 3.0 and click Next

  After the collection of certain data, the computer will restart, and the update will be gone.

  Hope this helps

  Post back if necessary

  ___________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Pavilion dv6 LY090UA #ABC: I reinstalled Windows 7 and my wireless network adapter does not work

  I just reinstalled windows 7 and I can not get my work a wireless adapter. I went in all directions looking for drivers to use and everyone I try does not work.

  I tried:

  Atheros Wireless LAN Driver 2011

  I saw someone talking about DriveTheLife in another forum and decided to try it.

  IT WORKS LIKE MAGIC, I don't know how he did it but he found and installed all the drivers I needed!

• Pavilion dv7-4270us: dv7-4270us bluetooth does not work after driver update

  I recently updated my drivers from the HP website.  Now, I know it was a mistake that bluetooth has not been installed correctly.    And there is no option "driver restore.  I tried several times sp50180, according to the HP website and also tried the old version listed (sp49153).   They old version did not install correctly and a new seemed especially, but none of my Bluetooth devices that used to work to do now.   I can 'connect to' some devices but they cannot transfer photos, connect to the audio, etc.  Some devices that are used to work can still be seen when I say "add a bluetooth device".  After installation, in the Device Manager, I find the following:

  The radio Bluetooth: Bluetooth Broadcom 2070 and Microsoft Bluetooth Enumerator (both working properly)

  Human Interface Device: Bluetooth Remote Control (works)

  Modem: Modem Standard via a Bluetooth #2 link (works)

  Network cards (all working correctly):

  Device Bluetooth (personal area network)

  (Heading RFCOMM Protocol TDI) Bluetooth device

  (and my other network devices, all functioning properly also)

  Other devices: this is the problem area.  After installation and reboot, I always find myself with 10 entries "Bluetooth Peripheral Device", all with a yellow exclaimation mark and all say real estate "Other devices", "unknown" (GSM) and the location is "on Microsft Bluetooth enumerator". "."

  I tried right click and uninstall it, but when I reboot they come back to the top, search windows update, but can not find a driver and go straight to the "other devices".  I also tried to uninstall the "Broadcom 2070 Bluetooth 3.0" 'Programs and features' and right-click to delete each listed above bluetooth driver and then run the sp50180 again and it will install without error and find the same above drivers that work and leave the same 10 does not.  And my Bluetooth headphones (two different ones) is more work (or can be seen) and my Bluetooth phone can be 'connected' but any attempt to transfer fails.

  I've exhausted all ideas on the web, I could find, and none have helped.  I tried to load a restore point, but after having so many pilot facilities, there is no point of restoration with the appropriate driver.  A full backup of the system on another drive, but much changed the applications and data files so I cannot restore it.  Unless someone knows how to use a full backup of the Windows 7 system to restore only the Bluetooth driver.

  Another idea is that the driver update that messed up things maybe changed some other file or a registry setting that is not corrected by sp50180, but that seems unlikely.

  Is it possible to manually install each of the 10 'other devices' drivers?  If I right click on a defective device and select "update driver software" no matter if I select the drive C:\ or F:\ (my driver and software download drive) or automatic search (including online) - it does not find the driver files.  I also tried to select properties and 'put to day driver' but the same results.

  Any help would be greatly appreciated.

  I found a solution. I received a call of support in Mumbai.  HP gave me a free call because they were not able to set a guarantee repair questions, so gave me the free support call.  I took an hour, but ended up the solution was very simple.

  There were these problems:

  1) 10 'other devices' in device with the exclamation points Manager can be uninstalled, but still were automatically reinstalled with the same exclamation point.  No pilot was available to the public for them.

  (2) my phone under Bluetooth devices could connect but would not photos transfer.

  (3) neither my helmet Bluetooth would not work.

  The solution was simply to go to 'Show Bluetooth devices' and right-click on each and select 'Delete device' (even if dimmed they might still be revoked).  After all have been abducted there were no "other devices" in Device Manager.  I then added each Bluetooth device again.  This was very well all work.  I also noticed my phone was five drivers "Bluetooth Device" was so 5 of the 10 exclamation points himself.

  For some reason, deletion of the driver in the Device Manager has not deleted the list "Bluetooth Device".  And by uninstalling and reinstalling the drivers, it does not work.

  If the answer is simple.  Before removing the drivers Bluetooth first remove all Bluetooth devices.

• Epson v500 Scanner does not work after driver update!

  I recently bought a V500 photo and scanned my first 35mm using Epson Scan v3.7.4 negatives. The colors seemed off so I download and installed the latest v3.7.7 of support to Epson.ca hoping that it might help.

  Following the upgrade of the driver, the scanner has stopped working! Loads of Epson Scan, but after 5-10 seconds, I get the message: "no response from the scanner. Make sure the scanner is turned on and connected properly. If you use the transparency feature, remove the reflective document mat. »

  Then I restored the latest install w / restoring Windows but still could not get the job to scan. I drove back to the pre - Epson scan install date and tried to reinstall the earlier version but still no luck to get scanner work.

  I then followed the steps of uninstall on the Epson.ca support site removed all the drivers and the software with the scanner turned off and unplugged. Then I reinstalled the old version of Epson Scan of the CD because he had worked at the start. I reconnected it the scanner it plug it in and turn it on. But it still does not work! Ditto for uninstall and reinstall with the latest drivers.

  Notebook P7350 using Windows 7 32 bit SP1. Scanner is connected directly on the laptop, not through a hub. I tried all 3 ports USB in the hope one would work, but no luck. All connections between the pc and the scanner seem robust.

  Any suggestions to get scanner work?

  Thanks for the reply of adeline. In the meantime, Epson come back to me when I contacted them again but only after I have disabled cookie blockers in Firefox when visiting their support site. The first time I've done this, and the support form has not sent correctly.

  It turns out that the scanner must be completely turned off and unplugged then reconnected after that driver installed. I discovered one of the records was not too tight that it should have been :-0 if I was sure I had checked it earlier.

  Thanks again.

• Satellite L50-B-1DZ - wireless network adapter does not work

  So, my network wireless adapter completely stopped working. 2 days ago I couldn't connect to networks wirelessly without problem (although I've disconnected and will need to run the troubleshooter every few hours to reset it...), but yesterday I started to get the message "not connected - no connection is available. In broadcom 802.11n network adapter in Device Manager, the icon has a yellow warning symbol and the error message "this device cannot start. Code 10 ".

  I tried to update the drivers, but it gives just the same error message. I also tried to do a restore of the system since a week ago, but it has not fixed either.

  I found a youtube video that said that the problem can be caused by a software conflict and change value from registry, but that no longer works, and now I'm full of ideas.

  How have you tried to update the driver WLan?
  Have you tried to uninstall the driver first, and then after reboot again to install the new driver downloaded from Toshiba UE driver page?

  Try it!

  You said you reset the system in the past?
  How? Have you used the Toshiba recovery procedure and have you installed already preinstalled system once more?

• Wireless network adapter does not work anymore and will not be repeated work without stopping the computer and then back on.

  Sometimes I leave my computer on at night.  Sometimes I notice that when I get back to him the next day that he has limited connection to the network I use.  When I try to disconnect it from the network, then reconnect, it says that it cannot connect.  Then, when I try to restart my computer it is sitting at a screen saying "stop down". "."  My wireless network software also is unaccessable in which she does not open and if I close the Task Manager and reopen it flashes for a second then closes.

  However when I turn it on manually and then turn it on again, which apparently is not good for the computer, I am once again able to connect to the network with full access.

  Can someone please tell me why this keeps happening and how to fix it?

  original title: unable to connect to a network.

  Hello

  Are you aware of any changes made to the computer, before the show?

  Method 1:

  Step 1: Safe Mode with networking

  Start your computer in safe mode with network and verify that the question.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: Clean boot

  If you are not facing the problem in safe mode with network, then put your computer in a clean boot and search for the issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once you are done with the boot, follow step 7 of article to put your computer to normal startup.

  Method 2:

  Update the NIC drivers and check the issue.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

  Method 3:

  Run a virus scan and make sure.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
   
  Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

  I hope this helps.

• Wireless network adapter does not work

  I get the error 10 and 31, and it won't let me access the internet

  Hello

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Check the site of the manufacturer of the system for latest driver.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Network adapter does not work after upgrade to Windows Vista Black edition

  Help, please

  I use to have windows vista and now I upgrade to windows vista Black edition.__i guess my network adaptar said corrupted__it network adaptar must be reinstalled .__i don't know where should I reinstall the driver__

  Microsoft does NOT Support Vista Black Editions.

  You will need to request support for Vista Black Edition where you have obtained/downloaded from.

  See you soon.

  Mick Murphy - Microsoft partner

• NETWORK adapter does not work after upgrade

  Hello

  I have two identical servers, HP ML350 G6, with an additional NIC from Intel (82574L).

  The first server running 4.0 and I upgraded to 5.0 without any problem.

  The other server was running 4.1 so I thought that there is no problem here either, BUT when I got to the installation/update I did not upgrade option, I had a migration of Force instead. He complained of two pilots 'oem-vmware-esx-drivers-net-vxge' and 'oem-vmware-esx-drivers-scsi-3w-9xxx '.

  I thought that the first server was no problem and it works well on 5.0 so I did a force to migrate.

  When the Force 'migrate' was done and I started the server I noticed that a NETWORK card no longer works correctly, Intel 82574 L...

  It says it is disconnected, and there is a red X next to it. I checked the first server again to see if it was really the same exact material and that's the only difference is that the Intel NETWORK card is working on the first but not the second server and they are now both on 5.0...

  How is it, I have had no problem for the rehabilitation of the 4.0, but when I upgraded to 4.1 I had these problems? And how do I fix?

  I need this server running as soon as possible.

  This good news

  Please mark the discussion as correct

• P0R94EA #ABU: brightness and HDMI does not work after driver update

  Hello

  I get a notification to update my drivers for HP Support Assistant that I took and I installed all the drivers involved and since that I can't not change the brightness of my screen or use the HDMI for display on my TV. I don't have the updates has been "Intel high definition (HD) Graphics Driver.

  Can someone help me with this please have tried different things from other sites, but nothing has worked.

  Hello

  Is there an improvement if you install the earlier version at the following link?

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72107.exe

  Kind regards

  DP - K

• VMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10 - known issue?

  Hello

  I upgraded the PC host, but also virtual machines to Windows Pro 10.

  TheVMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10...

  Is this a known issue?

  Thank you!

  Kind regards

  Joe

  SOLVED!

  
  

  I uninstalled VMware Player, including the abolition of the configuration files.

  
  

  re-installed VMware Player and it worked!

• Ethernet USB adapter does not work after update to sierra mac

  Ethernet USB adapter does not work after update to mac sierra.

  Please solve this problem as soon as POSSIBLE

  Hello guatamshah,

  If your USB to ethernet adapter does not work now that you have upgraded to Mac OS Sierra, there are a number of things we can try to get it working again.

  The first thing we want to do is to reset the SMC and the NVRAM on your Mac.
  Reset the management system (SCM) controller on your Mac.

  https://support.Apple.com/en-us/HT201295

  How to reset the NVRAM on your Mac.
  https://support.Apple.com/en-us/HT204063

  If the adapter is not still work after only two resets check to see if your Mac recognizes the device properly in the information system. In the Apple Menu, choose about this Mac, and then click the button 'system report... '. ». Once you have the window open system information, see the USB category on the left.
  OS X: about system information and System Profiler

  https://support.Apple.com/en-us/HT203001

  If she does not appear in the information system, see the articles below.
  macOS Sierra: If a USB device does not work

  https://support.Apple.com/kb/PH25343

  macOS Sierra: check your device's USB connection

  https://support.Apple.com/kb/PH25567

  However, if you do not see the device in system information, you may need to verify that network service appears correctly. In the Apple menu, choose system then Network preferences. You should see an entry similar to "Ethernet" on the left. If no, see the steps in the article below to add. Once add, test to see if your connection works with a disabled Wi - Fi connection.

  macOS Sierra: Add a network service
  https://support.Apple.com/kb/PH25279

  If it does not appear in the network, please let us know what you see on the right when you select the service, and the name of the service as it appears and we can go from there!

  Kind regards.

• my phone does not work after last update itunes on my phone connection with my pc, it shows only i tunes icon and the application of itune on my pc does not work

  my phone does not work after last update itunes on my phone connection with my pc, it shows only i tunes icon and the application of itune on my pc does not work

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  Once iTunes to work properly, you should be able to fix your device.

  TT2