SA40-702. Does not start, missing file...

Similar Questions

• A30 does not start: missing file

  My A30 laptop will not load windows because the following file is missing or damaged.

  \System32\hal.dll.

  It is not currently connected to the internet, which should rule out a virus, and it has worked very well before receiving this message. (except occasional overheating)

  I have loaded the system Toshiba Recovery disk, but am not sure how I can replace this individual file without wiping the entire system, or if the file I need is same on this disc (otherwise I guess I'll have to the windows XP disk?)

  Any help would be appreciated, soon. MattPope

  [Edited by: admin August 10 05 20:26]

  Hi Frank,.

  The hard drive on your A30 is below the optical drive. You will need to remove it first to get access to the hard drive.

  Optics drice is owned by a single screw (F5) on the bottom of your laptop. Remove the screws and the optical drive can be slid out of its compartment.

  The hard disk is then visible held by four screws.

  HTH

• Firefox does not start .oam file with scrolling parallax effect and if y > 740

  Hello!

  I try to explane my problem. If I place a parallax scrolling page of a lively .oam file, the .oam file does not start (as in firefox!) if the file is higher than y = 740 and if the animation with a scrolling parallax effect.

  Maybe just visit this site, you can see the problem. Please look with firefox!

  http://OAM-test.BusinessCatalyst.com/index.html

  I placed three times exactly the same oam-file with the same scrolling Parallax effects, but with different positions only y

  in safari and IE, no problem. but the third CAO does not start in firefox.

  any suggestion?

  by the way... Why firefox cannot load fonts in the oam file?

  Thank you very much in advance for any help. really need a solution as soon as possible. If there is no way to do it with oam-file perhaps another format without flash (gif)?

  Kind regards

  Ivo

  To work around the problem, you can configure initial field scroll to 1, it works with the third file oam.

  Thank you

  Sanjit

• Satellite Pro A60 does not start: missing or damaged config.sys

  Hello

  I turned off my computer Friday, I went back to his Monday - and it won't start. I thought that the config.sys file is missing or damaged.

  I tried all the usual methods - safe mode, last known good setting, OS etc, but none of it works. The computer does not recognize that the recovery CD is in the drive, either.

  As I don't have an original installation CD - the computer was shipped with the software already installed - I can't try either.

  I want especially to recover the entire system, but if I have to, I can live with that. Any suggestions would be welcome.

  Thank you very much.

  RONMAC

  Have you tried to boot your PC and press C after POST message? Recovery CD to be inserted.
  This C command forces the laptop to boot from ODD first.

  Maybe it works for you.

• Qosmio G30-161 does not start - NTDLR "file is missing

  Hi all

  I have a G30-161 double HDD (in Raid 1) which no longer starts...
  He just gives the message "file NTDLR is missing" and is followed by a prompt to restart the computer in which the same error will appear again.

  I got this laptop for my son to fix (lucky me :(!)

  Things, I've looked at so far:

  -Check the BIOS to see if the disks are configured properly - BIOS indicates the two hard drives installed, online and in RAID 1
  -J' had an installation of Windows XP by hand disc then tried to see if it would boot from a CD. He started on the CD ok, but the process Windows Recovery Console/install said he couldn't find any hard drives. Find an Acronis True Image boot disk (using linux I think), once again the started program end, but don't have it no hard drives installed.
  - So with no HD not reports I took one for a test. With disk 2 removed, in an attempt to start the system reports "RAID 1 is GRADIENT" then follows with "NTDLR file is missing. So this tells me that SW RAID working probably and he knows that a HD has been removed.
  All the patches I've read on the PC forums involve the use of the XP Recovery CD or some, but it won't work because the system thinks there are no disc when it starts. We have no ' have a Toshiba Recovery disk for the machine.

  Someone at - he saw the problem above, knows a fix?
  Can I purchase a G30-161 recovery CD anywhere?

  Any help appreciated. ...

  Thank you
  Steve

  Hello

  Looks like your drive is loked I found a thread in forum about the same error message and the user mikeptag posted a solution:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?forumid=58&ThreadId=24051

  I didn't test this procedure and, therefore, I don't know m if it can help you or not, but in my opinion it's worth to try

  Check this box and post your results

  Good bye

• Satellite A40-702 - does not start

  Hi, received by Satellite A40-702.

  Will not go back further than the logo Windows XP home start.
  Tried to use always the same CD recovery

  Thank you

  Your ad is a bit too short, and you should give us more details about your problem.

  Have you tried reinstalling the laptop with the recovery disk Toshiba or did you use the disc of Microsoft?
  I think that reinstall Windows must solve the problem, because your HARD drive will be formatted.

  In the worst case, there is something wrong with the HARD disk, and you must test this with Drive Fitness Test (use Google to find it).

• My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM.

  My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM. It is said it can be repaired by using the original installation CD, but we do not have. Any ideas please?

  The file is missing or corrupt is one of your files in the system registry.

  By far, the best way to recover from this is to go to another computer and create a free Hirens Boot CD.
  Download Hirens: <> http://www.hirensbootcd.org/download/ > (link at the bottom of the icon of the disk)
  Hirens CD burning <> http://www.hirensbootcd.org/burning/ >

  Once you create the CD, and then start your system of problem with this CD.  In the first window, select "Mini Windows XP" and wait for the system to start.  When it starts, go to the Hirens Boot CD menu and select
  Register-> Registry Restore Wizard.
  then follow the prompts.  This wizard will return a copy of your registry database from backups that are stored with your system restore points.  After the restoration, stop, remove the CD and restart.

  When you start your system, it is recommended to perform a system restore operation to ensure the consistency of your system
  "How to restore Windows XP to a previous state"
     <>http://support.Microsoft.com/kb/306084 >

  Also, this error is almost always accompanied, if not caused, the corruption of the file system.  Also a good idea to perform a check disk (chkdsk) operation with the option "repair".
  "How to perform disk error in Windows XP check"
     <>http://support.Microsoft.com/kb/315265 >

  The hard way to get back is covered in the following Microsoft KB article, but if you have installed a large number of service packs for your installation of XP, I don't give you many chances to get past part 1. (And there's also an installation CD to access the Recovery Console)

  "How do I recover from a corrupted registry that prevents Windows XP boot"
    <>http://support.Microsoft.com/kb/307545 >

  HTH,
  JW

• Windows XP does not start. «&#60; Root Windows &#62; \system32\hal.dll missing.» Reinstall the copy of the file"how to replace this damaged file?

  Have the XP Pro Service Pack 1 2002 reinstallation CD disk that does not start. most recent service Pack installed through updates.  Have the CD Drivers and Utilities from Dell 2005 "you must boot from this CD to run diagnostics, that may involve changing your computer's boot sequence. See the manual of the owner for info. I have my product keys.  Last week, I installed Norton 360 4.0.

  I am away from home long visit because of family illness. These disks were in my computer bag, but I don't have

  resources. I'm accessing the internet from another PC.

  I appreciated any help in getting my computer to start again.

  Thank you.

  Hi Sissi77350,

  · What is the model number of the computer?

  You must have the Windows XP CD to perform one of the steps to start the computer.

  See the links below: error message: "Windows did not start because of a configuration of the disk of the computer problem": http://support.microsoft.com/kb/314477

  With regard to:

  Samhrutha G S - Microsoft technical support.

• Error - NTLDR missing Windows XP Home computer does not start.

  Original title: XP-based computer does not start.

  XP Home does not start after I uninstalled a large file of Samsung mobile phone. I get a missing NTLDR error message and have had a System32 error as well, but there is no DOS prompt that would allow me to access anything whatsoever. Another problem is that I lost my installation CD. I initially bought this Dell PC nine over 6 years ago, so can provide identification details, if necessary program. Could someone tell me how I can make a recovery CD please? (No floppy drive not installed in the PC). To further complicate things (Yes, I know - I created many more problems that we all need), I have to keep my files on the hard disk, so cannot do a complete reformat, unless someone can tell how to save them somehow. My BACK skills could be summed up as "plodder inexperienced but determined!

  The file might be missing or it could just be that XP can't find it if your file system has somehow got corrupted.

  As the forums MS Answers does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  System32 error, you see, is what exactly?

  Depends on a few factors, there could be another copy of the file NTLDR in other places on your system, but you have to start on something to find out whether there is or not.

  After answering the above questions, I begin to make a CD from Recovery Console bootable XP by running a chkdsk/r, first on your HARD drive and then see what is left to do.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Computer does not start up___Can I download this file from the Microsoft Web site. I put the XP CD in and it starts downloading files but it asks what windows installation I want to and don't gives me one option other than press "Enter" to abandon.

  My laptop does not start at the top. It indicates that the following file is missing or damaged WINDOWS\SYSTEM32\CONFIG\SYSTEM.

  Download this file from the Microsoft Web site. I put the XP CD in and it starts downloading files but it asks what windows installation I want to and don't gives me one option other than press "Enter" to abandon.

  See if anything here helps-

  How to recover a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

  Install and use the Recovery Console in Windows XP
  http://support.Microsoft.com/kb/307654

  See also

  How to Troubleshoot Registry Corruption issues
  http://support.Microsoft.com/kb/822705

  How to fix a missing or corrupt Windows\System32\Config\System file
  http://xphelpandsupport.MVPs.org/how_do_i_repair_a_missing_or_cor1.htm

  TaurArian [MVP] 2005-2010 - Update Services

• Age of Empires 3 does not start on a vista machine, get this error "C:\Program Files\Microsoft Games\Age of Empires III\d3dx9_25.dll is not designed to run on Windows or it contains an error."

  I'm trying to play age of Empires 3 on my computer running windows vista Home premium and the program does not start. I get the error message: "C:\Program Files\Microsoft Games\Age of Empires III\d3dx9_25.dll is not designed to run on Windows or it contains an error." I tried many suggestions from Microsoft (resettlement program, reinstall in safe mode, update & reinstall the drivers for my video card, the compatibility issues with vista, updating and reinstalling directx 9.0 c, install vista service packs 1 & 2) but nothing has worked so far. I was able to play the game on the same computer with windows xp installed (it's a different hard drive that is not in the computer, and everything is the same) and it worked fine. My computer is old enough, but like I said the game worked before installing vista. ASUS A7N8x deluxe, AMD Athlon xp 3200 +, ATI radeon 9600, 2 GB OCZ ram that all suggestions are welcome. Thank you.

  Hi Raygun55,

  Welcome to Microsoft Vista answers Forum!

  This problem may occur if the Microsoft DirectX file that is mentioned in the error message is damaged or is not copied correctly.

  I suggest that you copy the file manually by following the steps and check if you are able to play the game without any problems:

  Manually copy the file

  To do this on a computer that is running Windows Vista, follow these steps:

  1 insert the disc 1 CD for one of the following games into the player from the computer:

  o Age of Empires III

  o Fable: The Lost Chapters

  o Zoo Tycoon 2

  o Rise of Nations: Rise of Legends

  2. click on start to reduce this includes this image and then click Documents.

  3. Locate, and then click computer.

  4. search and then click on the CD drive.

  5. Locate and then click the following folder:

  CD player :\ DirectX9

  Note In this folder path, the CD player represents the drive letter of the CD drive.

  6 double-click on Apr2005_d3dx9_25_x86.cab, right click on d3dx9_25.dlland then click copy.

  In Rise of Nations: Rise of Legends, double click Aug2005_d3dx9_27_x64.cab right-click d3dx9_27.dlland then click copy.

  Note Use the Apr2005_d3dx9_25_x64.cab file for the x 64 version of the Windows operating system.

  7. find one or more of the following folders, depending on the games that are installed on the computer:

  By car : \Program Files\Microsoft: Age of Empires III

  By car : \Program Files\Microsoft Games\Fable - The Lost Chapters

  By car : \Program Files\Microsoft Games\Zoo Tycoon 2

  By car : \Program Files\Microsoft Games\Rise of legends

  Note In these folder paths, drive represents the letter of the drive where the game is installed.

  8. right click on the folder of the game which is the part that is installed on the computer, and then click Paste.

  Note If you have installed more than one game on the computer, repeat steps 5 and 6 for the other games.

  You can check the link for more information: error message when you try to start a Microsoft game: "the file d3dx9_XX. DLL was not found": http://support.microsoft.com/kb/910813

  Alternatively, you can try to install the game in XP compatibility mode and check if you are able to play or not.

  Right-click on the game > click Properties > click on the Compatibility tab > select for XP compatibility mode > click OK.

  Let me know if it worked.

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• NEED to recover files from the xp computer that does not start.

  I changed startup on an old xp computer programs and now it does not start (I can accidentally put driver not run at startup). blue screen; STOP: 0x0000007B (0xF8992528, 0xC0000034, 0x00000000, 0x00000000) xp sp3 no safe mode without recovery does Center no disc. I just bought a computer to try to recover the information with win 7 but can not slave the drive to him because it is ide and the new computer is too modern. I need to save files are important on the xp computer is it possible to save them?

  I met this BSOD error several times, and the following fix usually (not always) allows the hard disk to be read by the system...

  -Boot your system and access the BIOS Setup
  -It will vary with different systems, but try to press "F2", "F10" or "delete".
  -If you need help with this step, let me know the model of the system, and I'll see what I can come up with
  -In the configuration of the BIOS, looking something like "Device Boot Configuration"
  -Go to the hard disk configuration and change the current option
  -Here are the most common options that I can think of:
  -SATA IDE, AHCI, (newer systems have more options, such as IRRT)
  -If the current option is "SATA", change it to "AHCI" or "IDE".
  -If the current option is 'DCIS', change it to "IDE", etc...

  It's just a quick run through a possible fix, without knowing the details of your system!  If you need more detailed help, I would like to know the details of the system, and we'll see what we can do!

  -Riley

• 0X803C0107 error: you cannot access shared files and printers and the MSE does not start at startup

  Original title: mainly MSE does not start at startup. have you tried re-loading and other elements on the card, still no luck. Here is the error code I have and the information complete.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • Error 0X803C0107

    Details of the editor for Windows Firewall troubleshooting

    Verified issues

    You cannot access shared files and PrintersYou cannot access shared files and printers

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445. Checked

    No workingRemote Assistance remote assistance does not

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance. Checked

    Windows Vista may not start Windows Vista FirewallWindows could not start the Windows Firewall

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned. Checked

    Windows Firewall service is not his firewall service is not started

    Windows Firewall service is not running or is not started. Checked

    Issues checked the details of the detection

    6 you cannot access shared files and printers checked

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445.

    Unlock the file and printer sharing in Windows Firewall works not

    To allow access to shared folders and printers, except for the file sharing and printers in the Windows Firewall must be enabled.

    6 remote assistance works not verified

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance.

    Allow Remote Assistance in Windows not running Firewall

    Which allows Assistance remotely as an exception in Windows Firewall it unlocks and corrects this problem.

    6 Windows Vista could not start Windows Firewall check

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned.

    Set permissions for the registry keys concerned not run

    Setting permissions for the registry keys concerned will solve this problem. Applies only to computers by using Group Policy to manage the firewall.

  6 Windows Firewall service did not start Checked

  Windows Firewall service is not running or is not started.

  Start the Windows Firewall service is not running

  Start the Windows Firewall service solves this problem.

  Details of detection

  Collection information

  Computer name: NORMBRESINSKI

  Windows Version: 5.1

  Architecture: x 86

  Time: 09-20-2010 07:51:49

  Publisher details

  Troubleshooting Windows Firewall

  Automatically fix problems of Windows Firewall, such as Windows cannot start the firewall service (0x5) Windows or Windows remote assistance does not work

  Package Version: 1.0

  Publisher: Microsoft Corporation

  You have problems with programs

• Error messages
• Recent changes to your computer
• What you have already tried to solve the problem

Hi Rickbsk,

You can check out the link and check the suggestions provided by scotty1294.

http://social.answers.Microsoft.com/forums/en-us/msestart/thread/05a63b12-1be9-4BD3-898e-64674c1e9afd

If you have not tried all the suggestions above, try and see if it helps.

Hope this information is useful.

Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I have a new computer running windows but 10, 13 photoshop elements disc.  Insert the disc does not start something going and looking at the files I do not see an installation executable.

  I have a new computer running windows but 10, 13 photoshop elements disc.  Insert the disc does not start something going and looking at the files I do not see an installation executable.  I don't know what to do.

  Download from Download Photoshop Elements | 14, 13, 12, 11, 10

  Install and enter your serial number.

• When Im in Lightroom 4 and make an edit in photoshop, after Im done making changes in photoshop that I do a backup, but does not load the file to lightroom. This just started happening. It was working before.

  When Im in Lightroom 4 and make an edit in photoshop, after Im done making changes in photoshop that I do a backup, but does not load the file to lightroom. This just started happening. It was working before.

  Please go to the location of your Lightroom Catalog, and there you will see the folder for Lightroom Catalog Previews.Lrdata