Sansa Clip + connect to Volkswagen Golf Mk7

Similar Questions

• When I connect my SanDisk Sansa Clip MP3 player Zip I get Code 10 device cannot start

  Original title: Code 10

  When I try to plug in my SanDisk Sansa Clip Zip MP3 player I get the device Code 10 cannot start.  I have XP.  The MP3 came with a 2.0 USB.  I don't know what the USB on my computer.

  Hello

  First of all, thanks a lot for taking the time to help me.

  After having tried everything you have suggested and have no chance and then by searching the Microsoft sites, Dell and SanDisk, I finally found a very simple solution that worked.

  Thought I would pass it for any future reference.

  The SanDisk site said to try this:

  Activation or forcing MSC mode on the Sansa player

  How to connect my Sansa in Mode "MSC" player or forcing MSC mode on my Sansa player?
   

  The steps below will force your readers Sansa Connect mode MSC on your PC.

  Sansa Clip Zip
  1. turn off the device.
  2 hold down the central button while connecting the device to the computer.

  Thanks again.

• Help! My Sansa Clip + is no longer recognized by my PC when connected by USB port!

  Reading, the latter time, ' said, 'written' only when connected. Normally, he alternates between the 'Reading' and 'Writing' when it is connected to the PC and, therefore, it USED TO BE recognized by the PC in these conditions. The device is not recognized in Windows Explorer as a device or disk as usual. I use Windows 7. The device is not recognized by Windows Media Player synchronization purposes: I can't synchronize playlists of music more.

  You try to reset by pressing the power button / stop 20 seconds does not help.

  Using different USB ports does NOT help.

  The cable using different USB does not help.

  Another computer has NOT appeared.
  

  SOLVED BY TECH SUPPORT CHAT: Here is the conversation with the restorative troubleshooting following steps:

  Jonathan Bailey is me:

  Kyle Ahmed is the man of SanDisk tech support:
  

  
  

  Of the troubleshooting information for "not recognized by PC.
  ***************************************************************************

  Kyle Ahmed: Please tell me the exact model, color, and the ability of your Sansa player?
  Jonathan Bailey: black, Sansa Clip +.
  Kyle Ahmed: Please provide me with the ability as well?
  Jonathan Bailey: I think it's a 4 GB
  Kyle Ahmed: Please tell me when and where did you buy this drive?
  Jonathan Bailey: Citrus Heights, CA, Jan 2012 target
  Kyle Ahmed: If I understood you correctly, your drive is not getting recognized by the computer?
  Jonathan Bailey: No, it is not when connected by USB.
  Kyle Ahmed: Please tell me, are you using Windows 7?
  Jonathan Bailey: Windows 7
  Kyle Ahmed: I understand. Please connect the player to the computer.
  Jonathan Bailey: It should say READING and WRITING.
  Kyle Ahmed: very well. If you please, right click on computer and select manage.
  Kyle Ahmed: Click Device Manager in the left pane.
  Kyle Ahmed: Sansa player will be displayed in the right-hand of Device Manager: 1. USB mass storage device
  (if the player has MSC) 2. portable (if the player is set to MTP mode)
  Jonathan Bailey: he is profiled as a Portable device Sansa Clip + 4 GB
  Jonathan Bailey: a yellow exclamation point icon
  Kyle Ahmed: right click on the drive with the error indicator and choose uninstall.
  Jonathan Bailey: icon done, went
  Kyle Ahmed: In the top menu, click Action, and then select search the hardware changes.
  Jonathan Bailey: said device still WRITTEN in reading
  Jonathan Bailey: said ball driver software not properly installed
  Kyle Ahmed: very well. Please disconnect the player from the computer.
  Jonathan Bailey: ok, says still WROTE
  Kyle Ahmed: Please press on and press and hold power for 20 seconds to turn it off.
  Kyle Ahmed: Then, press and hold the Center button while connecting the device to the computer.
  Kyle Ahmed: It is on the first view the drive between the up/down/left/right button.
  Kyle Ahmed: This allows the computer to recognize the drive as a removable storage as well
  You should see it in the devices with removable storage section in the computer.
  Jonathan Bailey: it says CONNECTED then he says SAN Disk alternately
  Kyle Ahmed: Check if the drive is recognized by the computer.
  Jonathan Bailey: there is now a SANSA CLIPP (F): in my Windows Explorer navigation pane
  Kyle Ahmed: It seems that pilots of the PSG of your computer went corrupt due to which your
  Player is recognized not earlier. In this case, what you have to do is to reinstall Windows Media Player or
  change the USB mode of the player to MSC permanently solve the problem. But the MSC mode will not allow you
  by creating playlists with Windows Media player to transfer songs from your player.
  Jonathan Bailey: Windows Media Player Sync now recognizes "SANSA CLIPP"
  Jonathan Bailey: I need Windows Media Player synchronization capability or the Sansa is not good for me.
  Kyle Ahmed: Jonathan, please check if the player is displayed under the Portable devices or with
  Removable storage in the computer (Explorer)?
  Jonathan Bailey: It's showing under devices with removable storage in the computer (explore).
  Kyle Ahmed: Please disconnect the player from the computer.
  KKyle Ahmed: Please activate the drive.
  Kyle Ahmed: Then go to settings > system settings > USB mode.
  Kyle Ahmed: Then in the player's main menu, go to settings > system settings > USB mode.
  Kyle Ahmed: PSG and click the Center button to confirm.
  Kyle Ahmed: very well. Now, connect the drive to the computer and check if she gets recognized or not.
  Jonathan Bailey: OK now recognized as his former self again.
  Kyle Ahmed: If the player is now recognized and alos appear in Windows Media player, I'm wrong?
  Jonathan Bailey: I have not checked the media player yet
  Jonathan Bailey: it is recognized in Explorer
  Kyle Ahmed: Please disconnect the player from the computer.
  Kyle Ahmed: To check the version of the Firmware of the player.
  Jonathan Bailey: ok, it says REFRESHING YOUR MEDIA
  Kyle Ahmed: very well. I would like to know once you are in the main menu of the player.
  Kyle Ahmed: Go to settings > system settings > Info.
  Kyle Ahmed: Give Me the version of the firmware of the drive please.
  Jonathan Bailey: Version V01.02.16A, isn't it?
  Kyle Ahmed: It seems that the version is up-to-date.
  Kyle Ahmed: The reason why it took more time to update the media earlier must be because of the large amount
  songs that have been transferred, which can take the time to read.
  Jonathan Bailey: OK, for 2 500 songs, it usually takes about 15-20 minutes
  Kyle Ahmed: I understand.
  Kyle Ahmed: You have faced a temporary problem that was solved by resetting the player and refreshing the drivers of your computer.
  Kyle Ahmed: You should not face additional problems.

• Sansa Clip 2 GB shows "Connected" when the charger is plugged

  I have a Sansa Clip 2 GB is around the age of 6 months.  He played very well for 5 months, but for the last month, he periodically left the game and shows 'Connected' when the charger is connected.  I can sometimes turn off and on and it will start working again.  He will play for awhile, sometimes minutes, sometimes a few days and then stop playing again and see the "connected".  When he is in this state it will load but not play.  I tried 3 different Chargers and all have the same problem later.  I updated the firmware of 01.01.32 but no help.

  Someone knows how to fix this?  TIA for any help.

  OK, here is the last, this problem is resolved, but he caused a new sorta related problem.  What I did I deleted all my files and just put all the songs in the Music"" folder.  This seems to have solved the problem where it says 'connected' and stop playing, however, now it plays a day or two and then stops himself.  I just press 'Play' and he starts going again, so it is not much more than an annoyance I can live with that, and I could see where maybe he could do so on purpose after she played all the songs, but why it not it that way when I got it?  He played continuously day and night for months as a first step.  I'm confused, but I can at least live with the Clip now.

• connectivity of Sansa clip

  I bought a 3.5 mm audio jack, standard usb cable to connect the clamp on my car radio usb port but no sound speakers, I also tried the clip connected to the laptop with the same cable, but still, no noise.

  is it possible to play the clip via an audio jack to a usb cable?

  Maybe an audio jack to the audio input cable connected to the decision-making of the ipod on the car radio will work?

  A cable 3.5 mm male-male between jcak helmet of the player and the car radio to THE (or AUX in) jack will work.

  A short USB to the USB cable from the player to the USB port of the radio works as the car radio is equipped with such, and the files are in a format readable by the stereo (typically .mp3 or .wma). Check your car manual for the owner for details.

  A Jack of 3.5 mm to USB cable does NOT work.

• Power outage Sansa Clip

  Hello

  I have a 2 GB Sansa Clip I bought about 4-5 years ago and have been very happy with it.

  He runs the version of the 01.01.30A software.

  However, recently and for no apparent reason suffering from power cuts.

  It would just turn off, no matter how much battery there left, how long it has been running or what he does. And when we turn on (which is sometimes hard to do) he can't remember the last thing he was playing.

  After further tests it seems to turn off when put under different angles, almost as if there is a piece on the inside that is open/close the connection. When shaking a slight ratteling inside there, but I can't be certain that's not making noise power switch.

  Of course, this looks like a hardware problem.

  So, how can I open it and fix it? Is there a diagram somewhere I can look at?

  Thank you

  Max

  Well, I opened it and looked around in there.

  True, the battery had detached from its adhesive strips and pulled the loose battery negative cable.

  Gently, I took out the battery and was able to resolder the wire and test that it works before you all shut up.

  My double-sided adhesive foam Strip seemed to be too thick, so I used a drop of silicone glue to prevent the battery from moving around.

  All together again once, case snapped back and forth between them well.

  A little notation around the seam is a small price to pay for a media player that fully operational once again.

  Thanks for all your suggestions!

• How WE / OFF sansa clip jam

  I bought the sansa clip jam, and I can't ON / OFF.
  I need to wait a few hours and sansa clip jam is off and connect him to the load to the sansa clip jam
  Where is the ON / OFF?

  Click and hold the Center button for three seconds. Same on/off button.

• Sansa clip + does not see the audio books I have loaded

  I got my Sansa Clip MP3 player + for two years and it works very well, so far.  I only use it for audio books.  Recently, I reformatted the player and loaded new books in.  When I went to read, the audio books folder was empty.  I have connected the player to the computer again, and the books were in the audio books folder, where I had loaded.

  I've updated the firmware to the V01.02.16A Version, and there was no change.  I tried to reset by pressing the start button. No change.

  Memory has 3750 MB with 3135 free, indicating that there are books in memory, but the player does not see the.  What is going on?

  That's all!  I checked the format of audio files.  It is the AAFC, with suffix .m4a.

  The Sansa manual says:

  "The Sansa® MP3 Player will support MP3, WAV, WMA, secure WMA, FLAC, Ogg Vorbis and audiobook formats.  I guess that AAC is not one of the formats that they support.  So I have to convert .m4a to .mp3.  I guess there are a lot of tools to do it.  Any suggestions about which one is the best?

  Thanks a lot for this revelation.

• Sansa Clip + doesn't turn on

  I need to know how to get a replacement for my Sansa clip.  It was purchased through Amazon on 2.19.14.

  It lights when not connected to the computer.  It remains quite dead.  It lights up when it is connected, and it is recognized by the computer.  I am able to transfer files when it is connected to the computer.  As much as I know it was not dropped or damaged.

  I tried things.

  I tried to reset the player several times.

  I tried to reformat the drive

  I plugged in the charger and left more than 2 days.

  I have it plugged into the computer and he left.

  Always as soon as I disconnect the computer it goes completely dark.

  http://www.SanDisk.com/about-SanDisk/contact-us/

  http://KB.SanDisk.com/app/rmaform/session/L3RpbWUvMTQyMTUyMjEwMC9zaWQvamE0S1JIY20%3D

• Need HELP! My Sansa Clip + is no longer recognized by my PC!

  In fact, when I connect my Sansa Clip + to my PC via USB, it will recognize in 'My Computer' for a fraction of a second & then it will disappear! The disc for my Sansa will be apear for 2-5 seconds & then bam, gone.

  Sometimes the Sansa Clip + will reappear again at my drive after leaving connected, but even once, it will appear only for a fraction of a second & disapear as he was immediately disconnected.

  After that my Sansa Clip + is going to just play the music as it was not yet connected to my PC with the USB cable. I don't think it's the same in charge when connected.

  I have an another spare Sansa Clip + & when I connect it to my PC with the USB cable even & the same USB port, it is perfectly recognised! No problem with that!

  My Sansa Clip dies or the USB connector on the end let go & not able to login properly?
  What I have to buy a new, or is it repairable?

  Have you tried to exchange the cables? Sounds like the cable you use (which connects intermittently or fresh) may have a loose wire or PIN.

• Sansa Clip + does turn on at all!

  My Sansa Clip + (4 GB) will not turn on. I tried:

  • By pressing the power button while up to one minute
  • By pressing the power button and the Middle up to one minute button for
  • Plug USB wall adapter
  • Connect to computer

  No sign of life at all.

  I loaded full yesterday and I used it this morning, but an hour later it just stopped working.

  Help, please!

  I found the problem:

  Sansa clips don't work not in sous-zero temperatures, and when they fail, they are not off, so it's a combination of battery flat and temperature.

  FIX: In a setting slightly warm place (sometimes several days) just leave it plugged and turn it on.

• Sansa Clip Zip battery does not charge, goes directly to the screen of the song

  It's my third Sansa MP3 players.  The first was a Sansa Fuze with the round button.  Like that one but my husband needed more that I did it I gave it to him.  He is old, but the player is still so today.

  The second was a Sansa Fuze + with the touchpad.  The touchpad has been way too sensitive but I need to play only two songs for sleep therapy while I was fine with it until the battery suddenly stopped charging a few months ago, I posted my problems in the Sansa Fuze + forum.  After trying a few suggestions, I finally accepted that he was a Goner.

  I bought this Sansa Clip Zip 4 G, thinking that should last at least for a while because I use every day.  In fact, I needed only when I had disorders of sleep during the night;  I probably used it once every two weeks or more.  I used my cell phone to the device, had no problems until now.

  The last time that I loaded it was 2 weeks, to 98% full - the thing never indicated 100% while it was a little weird.  In any case, I had problems sleeping two nights ago so I took out the Clip Zip and noticed that the battery still had plenty of juice left.  This morning I checked the battery, he had 68%, but I thought I needed could again tonight so better it load up, just in case where.

  I connected it to my computer, but it did not show "connected" screen  Instead, he went straight to the last song I listened to.  I thought it was weird so I turned off the player then tried again.  Of course, he went directly to the screen of the song.  I noticed that the battery icon was showing 'filler '.  I thought that if I left it connected to the pc long enough IT would eventually deducted.  Two hours later, I checked the computer and it says that the drive battery was dangerously low.  I disconnected and then reconnected and this time he said 98% charged.  I loaded a bit more just in case so I used the player for about 15 minutes and the player turns off.  Plugged into the pc and now it says battery is extremely low, while the last hours do not charge the battery, but it drains pretty!

  My last attempt was to plug into a wall charger and guess what?  He went directly to the screen of the song once again.  Contrary to connect to the computer, I could actually turn off the player but this way does not charge the battery, or.   It's exactly the same problem as my second player, the Sansa Fuze +.

  I bought the last two players from Sansa, simply because I really liked the first which of course had been abandoned a long time ago.  I don't know if I have bad luck or it is just an issue joint Sansa players but one way or the other I don't buy any Sansa more in the future.  He is a big name that comes with the big disappointment!

  You can also try a reset by pressing and hold the power button for 20-30 seconds. Release it and then turn it on normally and see how it behaves.

  By your description of the message "dangerously low" you get then plug it into your computer, which tells me that you use MTP mode on the player (or default automatic default, MTP). MTP mode can be pretty weird; better to use MSC mode unless you have need to PSG for "protected" content or DRM files such as Rhapsody or audio in your library or Audible books. The small "crirically" message is a bug in Windows 7 (using MTP mode) that Microsoft did not consider important enough to fix.

• Structure of the menu of the Sansa Clip +: change USB Mode no display

  Hey,.

  I have a Sansa Clip + with a display of death.

  I need to change the USB Mode of DPW, Meteorological Service of the Canada.

  Can someone please tell me the structure of the menu in order to change the USB Mode put down using the screen?

  Other clues would be appreciated.

  Thank you!

  I just found the solution:

  Sansa Clip +.
  1. turn off the device.
  2 press and hold the Center button while connecting the device to the computer.

  http://KB.SanDisk.com/app/answers/detail/A_ID/61/~/enabling-or-forcing-MSC-mode-on-your-Sansa-player

  So now I can install Rockbox and set up the clip + so that it displays all the entries menu...

• Sansa Clip - computer does not recognize the music file

  I have a Sansa Clip 8 GB. It works OK. It connects to my PC (Windows 7) and fees. But when I open the music from the PC folder there is nothing in it. There is the music of the clip and he is playing. But nothing in the folder on my PC. The clip has the firmware version: v02.01.35A. His car is up to date. Any ideas?

  Try changing the drive USB MSC mode by going to settings > system settings > USB. If you still don't see the files, try MTP mode. Files transferred in a mode are invisible to your PC when it is connected to the other mode (files transferred in both modes are still visible by the player himself, that's why they play even if the PC cannot find them). The third mode, "Automatic Detection", should be avoided because it can change between the MTP and MSC between sessions without warning, according to the whims of Windows.

• Sansa Clip + does not start or is not recognized by my computer.

  I listened for the Sansa Clip + to work for about two hours after charging the battery. It stops all of a sudden. It will not turn on, nor is it recognized by my computer. I tried a soft reset by holding the power button and I still get nothing. I tried to connect to different computers and different USB ports on each computer. I can also load with another cord which is not read.

  Any help would be appreciated, thanks

  Have you tried holding down the power button (some say 30 seconds, but I don't think he'd be as long) and then releasing and clicking it normally? This is what worked for me both times as my Clip + died spontaneously.