Sat Pro 6100: firmwareupdate for wireless CardBus TI 1410 Lucent ORiNOCO

Similar Questions

• RTC & Sat Pro 6100 battery

  Sorry for my bad English.

  If the cmos of laptop battery (I have a sat Pro 6100) is damaged completely, the laptop also ignite?

  Hi Biagio,

  The RTC (or CMOS) battery is installed on the motherboard, and is used to keep the BIOS settings when the laptop is turned off. If the RTC battery is faulty then the date/time and other parameters of the BIOS only be not maintained when the laptop is shut down for a while.

  The normal battery will be affected by the failure of the RTC battery and will always recgarge as usual when the laptop is connected to a power source.

  The RTC battery can be charged by connecting the power supply but leaving the laptop off for about 24 hours. If the date and time is always lost after that the RTC battery should be replaced by an authorized Service Agent Toshiba.

  HTH

  Post edited by: NickyNoogle

• Sat Pro 6100: Moving by itself of the mouse

  Hi all
  You have a question about a problem I'm having with my mouse two USB and the joystick on my satellite pro 6100 xp sp2

  The poroblem is that the cursor moves off the screen, either in the top right or bottom left. Tired using laptop without usb mouse same problem, have scanned laptop in case of virus, found nothing. been looking for the web, but only to find that the people who have had this prob is with mouse Sales (Laser or infrared ones)

  I was wondering if it's got time my keyboard replaced in which case this is the problem is, the mouse uses a bit of the keyboard to work.

  Someone at - he encountered this before and could point me in the right direction

  see you soon

  Hello

  Well it s strange. The problem occurs if the joystick is not connected?
  This resembles the function of calibration of joystick or mouse.
  Have you tried to calibrate the joystick?

  Also the same problem occurs if the accupoint mouse trying to calibrate. The mouse cursor moves to 5-10 seconds. Right now you shouldn't t touch the mouse.

  Good bye

• Sat Pro 6100: The orange light blinks

  GDay guys,.

  Thursday, it was the last day of school.
  In the last lesson of the day, I used the laptop to play games (Toshiba Satellite Pro 6100, 1, 6 GHz) when the Bell went. I tried to stop in time, however running in battery mode, she went up to 1 ghz and has been quite slow, closing the game so I immediately turned it off by holding the button for a few seconds.

  I put it in my new computer case belkin which offers a thick foam padding and went home by bus. When I finally got it, I plugged the laptop and tried to boot the system. The screen didn't work for some reason, so I tried the key light several times without success. Reset the computer several times, still nothing. I was wondering if it was the hard drive of the stopping is not correctly earlier this day here but I could always blindly log windows. It me intrigued as to why the screen wasn't on. I presume that a cable was loose so I removed the keyboard and checked the cables on the graphics card. They were fine. Put the keyboard back on and tried to start the laptop.

  The flashing yellow light has shone in its ugly glory. Something was wrong. I left the cell only and got the father, who is an electrical engineer to check on the laptop for all things obvious which could cause this problem. Dad couldn't see anything.

  Before, I read a post on the resettlement of the graphics card can work so I reinstalled the graphics card and tried to boot the system. Still nothing!

  What the hell is happening?

  I read these support forums and find a post on how you can charge the battery, start etc and try it and watnot, but it still fails. When I remove the battery and exit onto the adapter and replace the AC adapter in, a green light that shines above its power light shines. When I put the battery in again, a yellow light shines above the stack, however as soon as I press the power button, everything shuts off and the yellow led shines above the logo of ac power...

  Any ideas as to what may cause this problem and how can I solve this problem?

  -Well done guys!

  Hello

  Littco is right. You must contact the partner in your country. On this way is really not easy to say what can be the problem, but I guess Hat there is a problem with the electronic control gear and you will not be able to repair only. Check it please this page

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_gaspLocator.jsp?PF=true

  and there you can find a list of aspic in your country.

  Good bye

• HP Officejet Pro 6100 < DRIVER for XP 64 - bit COMPUTER?

  I bought a printer "HP Officejet Pro 6100" (product # 0225085) from Office Depot online, but I don't think that there is a "PRO 6100".   ... but I digress.

  I just wanted you to know background information.

  It seems that the 6100 Officejet does not support 64-bit XP computers.  After talking with HP Technical Support for more than an hour and even if they promised me a work-around, I'm stuck and cannot print.

  I wonder if you can help me find a driver so that I can print from your desktop Dell under XP 64 BIT?

  Q: is there a work around to make it work, or do I have to return the printer?

  FYI old printer - HP Deskjet 6122 - has been directly connected to the XP 64 - bit.   ... but I wonder if if would make a difference if I used the eithernet cable connected directly to the Airport Apple router and tried to print from there.

  THANKS a lot for your help!

  Henry

  Hi Henry,.

  There is no support for operating system XP 64-bit for this printer. You will need to do is install the driver of 990c of the operating system to use this printer for printing basic functionality.

  Follow the instructions below.

  1. open devices and printer

  2. click on add a printer

  3. click Add a local printer

  4. from the use existing port, select the USB option and then click Next

  5. click the button of Windows Update to get all the updates

  6. once the update is complete. Click HP from the menu on the left, then select the printer Deskjet 990c in the right menu, and then click Next.

  7. follow the remaining instructions to complete the installation.

  Once you have the printer added 990c make sure it is the default printer, and then try to print on your Officejet 6100 printer using this driver. I would like to know if you have the same problem?

• SAT Pro 6100 Modem and WLAN problems

  Hi all

  I have a portable SP6100 which had reinstalled WINXP SP2, allows to detect the PCI modem but not install and WLAN installed the drivers but it cannot see all wireless networks. I tried to download and reinstall the latest version of these drivers on the Tosh site and did the MS updates but still no joy. The modem will not install, it says invalid drivers. If removed WLAN drivers, reinstall automatically on reboot (Tosh Wireless LAN Mini PCI Card) but still does not work. Someone had problems with this? See you soon...

  Hello

  First of all, I would like to say a few words on the question of the modem;
  To my knowledge the laptop is equipped with a chip modem Scopio (Agere AC 97)
  You need a XP driver that supports this chips and SP2!

  I also checked the page of the Toshiba driver and found information for Microsoft Windows XP SP2 update.
  It seems that the BIOS should be updated version 1.90 or later!
  In order to check your installed BIOS!

  Now something of WLan:
  It seems that the laptop supports a standard Wi - Fi: 802.11B and WEP encryption.
  If your WLan router has been set at G orto your, you will not be able to see the WLan networks!
  The router must support the 802.11 standards B

  Remember that your wireless network card is compatible with the Wlan router!

  I am owner of 2 laptops. One of the laptop uses a 802.11 has / B card Wlan and my router supports the B/G 802.11 standards.
  A laptop cannot connect to this router because of the different standard.
  Maybe it's the same reason for your problem of s

• OfficeJet 6100: HP Officejet 6100 configured for wireless than no. Longer exists. How to reconfigure it?

  Hello

  I have an Officejet 6100 which was my computer classroom. After his retirement, I brought the printer home. I tried to configure it to print via my WiFi at home. When I print the diagnostic report, it shows that the printer is always set to the WiFi of the school. However, the school, and therefore the WiFi, no longer exist. Is it possible to reconfigure the printer, or simply remove the connection with previous WiFi? If so, how that would accomplish this?

  Thank you 1 x 10 ^ 6.

  Mark

  Publisher and editor-in-Chief
  Red 2 - the Magazine for teens

  So, I have a younger brother who is fond of asking stupid questions. Watching me struggle to install this printer, he asked: "have you installed the software?" * beep * it! Installation of the software, did the trick. Imagine that.

• Sat Pro 6100: Startup takes to long after the BIOS update

  Hello

  I have improved my 6100 to bios 1.90, but now starts, it takes about 1 minute to get the Toshiba screen, and after the beginning of the boot, the system stops.

  Can I somehow downgrading the BIOS on my own?

  Hello

  Downgrade of BIOS is not possible. Service partners just to do this.

• Re: Sat Pro P300 - setting for the user account problems

  Hi guys, the fact that someone knows what this means when the main user (who is the administrator of the computer) will not connect?
  It comes up with an error: the user profile service is unable to open. Profile of user cannot open.
  I can connect with all users on the computer, just not the main user. And this is the account that everything is connected too.
  So I need help! Please, I beg you.
  Thank you

  Hello

  This seems to be a known issue from Microsoft with Windows systems.

  I found this fix MS:
  + Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. User profile cannot be loaded.
  http://support.Microsoft.com/kb/947215

  Run the * Microsoft Fix it 50446 * mentioned in the knowledge base article should help.

• Sat Pro 6100 - black LCD screen

  On my laptop, I have a black screen.

  If I connect an external monitor, everything goes well on my external monitor, the screen is always black?

  Anyone know about this problem?
  Is there something to check or repair?

  THX in advance

  Hello

  It seems that your device uses only the external display. Did you change the graphics settings in the graphics properties or with the FN keys?
  As far as I know you can use the FN + F5 key combination to switch between display devices. In addition, you should check if the Display 2 in graph properties is not used a primary monitor.

  Good bye

• Satellite Pro 6100, WXP SP2, once in mode installation ensures the unknown USB

  Hello

  After you install the update in Win XP SP2 on my laptop Toshiba SAT Pro 6100, the following occurs:

  When the laptop wakes from sleep mode, the USB connector is unknown and the communication is lost.

  Who knows the answer to this problem?

  Hello Erjee,
  you just need to install the version of the bios 1.90 or later.

  For other machines with the same problem after installing SP2...
  TE2100 v1.60 or later version
  SATELLITE PRO 6000 v1.60 or later version
  PORTEGE 4000 v2.10 or later version
  TECRA 9000 v1.40 or later version

• Signal not detected on Satellite Pro 6100 wireless

  I have two laptops Satellite Pro 6100, two of them are configured to automatically connect to our local wireless router which they both started.
  A computer is used by myself by my wife; bookmarks, email accounts and so on are different on every computer/hard drive.

  I have problems with one of the computers (mine) - the usual problem with multispindle connectors on the video boards and feeding, then I tried to use "his" computer with 'ma' machine's hard drive.

  His machine does not recognize our LAN with my hard drive installed. He came up with a new network found, but not a wireless network. Also, with this machine and my hard drive installed, can't the machine to search for wireless LANs, the icon does not appear. The switch is turned on for wireless signals and it works very well with his hard drive in it. The network is protected, and the two machines have the same id in them for connection which work fine in the original engine.

  I don't really understand this condition. Something in the bios? Something on my hard drive that is not recognized by the computer? the wrong phase of the Moon?
  Suggestions how to trouble shoot and fix this?

  Both machines are XP Pro on them, latest updates.

  Hello

  Also AFAIK, Satellite Pro 6100 was equipped with different Wlan cards so if use different HDD with different driver then the Wlan card could not be detected by Windows XP.

  Check if the wireless adapter is listed in the Device Manager and recognized correctly.

• Wireless causes to the satellite Pro 6100

  Hi I have a pro 6100 and just recently, I replaced the card WiFi mini PCI card [PA3171U-1MPC] 802. 11 b with PA3236U-1MPC a / b combo. The site Web of Toshiba shows this combo Mini PCI card as being compatible with my model so compability shouldn't be a problem.

  At the same time, when my PC has been upgraded, I also added a Bluetooth PA3121U-3BTM module to my PC.

  Recently, I tried to connect via the wireless link and I could not do. I looked in my device manager and it has not shown that the new PCI Wireless card was recognized while previously it showed that Toshiba Mini PCI Wireless lan.

  I can see now is that--

  Area of personal network Bluetooth Toshiba
  Intel(r) Pro/100 VE Network Connection
  TRP Win Miniport
  GlobalSpan USB ADSL Lan Modem

  Bluetooth

  Bluetooth RFBUS from Toshiba
  Bluetooth RFHID from Toshiba
  Toshiba Bluetooth RFCOMM
  Bluetooth RFBNEP from Toshiba
  I was wondering now that I have Bluetooth maybe causing this conflict?
  Why is the Mini PCI card is not displayed in my device manager or go through what I wrote more high is this normal? The Mini PCI card has been attached by a computer technician and I have no doubt that it has been correctly mounted.
  Thank you

  I think I can solve my problem but I'm not entirely sure.

  I went to the Toshiba site we and downloaded the drivers for the PCI Atheros cards {driver WiFi Atheros 802.11a/b/g with support Cisco/WPA for Windows XP / 2000 (v2.4.2.14, 11/11/2003; 3.72 M)} and now in my list I see Atheros AR5001X Mini PCI Wireless Network Adapter
  I hope it is the right one?

  I can now access the login box for the wireless, which is a promising sign. I can't test it at the moment because I do not have a router at your fingertips right now.

  One last thing, when I press my button FN and F8 it does not bring the message that wireless is enabled. It is used for, but not now.
  Anyone know why this might be?

• Satellite Pro 6100 - Wireless Lan cannot be activated.

  All afternoon - I have just my hands on a Satellite Pro 6100 and am impressed to bits with it.
  The only thing that is bothering me is put on the wireless LAN doesn't work. Here is what I tried:

  (1) use the switch on the left side of the laptop - push back for "wireless WE"-no led or an indicator.
  (2) use the FN and F8 for the shortcut - key no joy.
  (3) install all the drivers available.

  It is to have no chance at all. I currently have Windows XP SP2 on board and have lost count of the restarts. I looked at the page update SP2 and found a registry setting, but that does not change. I'm pretty sure that there is a wireless card installed - I found the antenna, but I would appreciate some advice please if anyone has experience this, or is somewhat an expert at this.

  Thanks in advance to you all,.

  Select this option.

  It worked before or since when did that happen?
  You could take a look at the Device Manager if the wlan device is entered correctly without no exclamation point.
  Correctly installed all the drivers and updated? Maybe a BIOS update can help.

  Of course, the laptop was equipped with wlan? Not all 6100 built in wlan.

• Need info on compatible cd/rw drives for Satellite Pro 6100

  Hello
  can someone tell me the readers of cd/rw compatible for a 6100 sat pro that I can't find it on the toshiba web site
  any help would be appreciated

  Can anyone help?

  Hello

  I found these 2 drives:
  Slim SelectBay DVD Multi Drive PA3231E-1DV1
  Ultra Slim DVD +-RW Drive PX1296E-1DV2

  Good bye