Satelite L750 - "check the cable connection. no boot device. "

Similar Questions

• Don't check the cable connection no bootable device insert boot disk

  I have a laptop Aspire 5733Z which sometimes gives me the message above. When that happens, I leave it alone for 3 or 4 days and when I turn it back on it works again. I went once to a technician, but when I arrived, my laptop was working fine. I noticed that if I ask to work with Mozilla Firefox or some complex video sites, it crashes how can I do to get a boot disk? or fixing the problem?

  Hello...

  This could be an internal hardware problem, this message usually when the hard drive is not detected by the BIOS.
  What HARD drive is not detected that the system is not a starter and promts to insert the startup disk.

  If the computer is under warranty, it is better to sedn inside to get the problem resolved.

• Error starting: "check the cable connection.

  Original title: that check the connection of the cable during the start up to the average?

  When I boot my computer says check cable connection? my computer crashed and has messed with it when you start to get in the system until I restored the computer to its original state. help I don't want to go through this again

  Hello

  ·          What version of the operating system is running on your computer?

  ·          Where there are changes made to your computer before this problem?

  ·          Question took place even after the computer has been restored to its original state?

  ·          It's a laptop or a desktop computer?

  This happens usually when the physical connection to the computer is not intact. Make sure that the physical connections are correctly configured.

• Equium M70 LAN adapter - it tells me to check the cable connections.

  When I connect a cable to the LAN adapter to the back of the laptop, how can the status LEDs should he show.
  I have only one view. Does that mean I have a problem.
  I am trying to connect to my ISP using an ethernet cable. He always says check cable connections.

  Near the port of LAN, there are two LEDs available: orange and green. When the LAN cable is OK and connection is where the Green led is permanent. The orange LED blinks when data transfer is available. Please check it carefully.

  If the Green LED is not on after connecting the cable LAN there are three possibilities:
  The LAN cable is defective
  Your router settings are bad (MAC settings or IP address)
  Or in the worst cases the LAN card on your laptop is defective (check in the Device Manager)

• Satellite A30: PXE - E61 media test check the cable failure

  OK got this message on a cell phone of friends
  Others have played with him and made it worse, and now I received the laptop to try and fix.

  When you start to get

  PXE - E61 media test check the cable failure
  PXE - M0F outgoing PXC Rom

  If his tent to boot from the local network instead of the hard drive I have reset bios by default I disabled everything when I F12 boot to hard drive get the error message rΘation and one at a time, that nothing works even when I try to disable lan starts, he tries always to.

  When I try to install from disk backup it is hard disk not found, but in the bios the hard drive is located and can not boot from it.

  I tried with winxp pro disc to try not to get an OS on the laptop any partition to the OS but a blue screen with an error 0 x 00000050 CrashFree disk gives error 1170 if I remember correctly.

  I can't update the bios with new version because she needs windows, I can't stop the lan because there is no setting in the bios very minimul with about 4 useful settings in it.

  Is the hard drive turned or is this a bug in the bios that it detects drive hard, but does not assign a letter properly?

  If I try the recovery console in xp Setup there is no disk to read or write, if I maps the drive in recovery only the cd/dvd rom found no hard drive.

  Any help would be great thank you because I don't know what to do, I don't think that the hard drive is shot myself but maybe if I can get a laptop and try the hard drive what she will say if it is or not, but for now I'm stuck with no. had to go.

  I tried many things
  1. cdrom out and replaced plugs
  2. Jack hard drive out and replaced
  3 took Ram out and replaced
  4. start since the utility disk
  5. start from the winxp disk
  6. Windows XP recovery console no hard disk on c d e f g
  7 disc utility says no hard drive gives me a x: > promt error number 11030 invalid destination by car. Hard disk by bios HITACHI DK23FA-30-(PM)
  9 winxp error if I try to install 0x0000008e

  Post edited by: Shoa

  Post edited by: Shoa

  Hello Shoah

  You did what I would recommend.
  I remember what one of my friends has had a similar problem on an A200. But after the BIOS reset by default, he was able to install the OS from the recovery CD.

  The whole is very mysterious. It looks like a HARD disk failure, but the HARD drive is recognized in the BIOS. But have you checked the HARD disk in other laptop or computer?
  You can try to connect the HARD disk via the external USB HDD controller and could check if it s ok and could format.

  I recommend also to remove the CD/DVD drive and the HARD drive, then set the BIOS to default settings immediately (don't forget to save changes). Then try to power upward without the HARD disc and the drive.
  To my knowledge, you should get an error message.
  Then stop the laptop and put both the device in Notepad. Then go to BIOS and check if both devices are properly recognized.

  Finally, I must say that I don't know if my proposal will help m.
  If she won't help, you will need to contact an ASP in your country, because it really looks like a serious problem.

  Good luck

• "Connection error. Check the Internet connection. »

  I just installed my printer (an HP CM2320fxi upgrade). Everything works except ePrint/Web Services. The printer is connected directly to my router. It prints network computers. AirPrint works from iOS devices. It can scan to e-mail and documents are properly received by mail outside the network accounts (i.e. it must be connected to and talk to the internet). All the router firmware and the printer has been confirmed to date. all devices have been reset and restarted several times. However, if I try to activate HP Web Services for ePrint installation, I get the following error message: "connection error. Check the Internet connection. »

  After struggling with this issue for many months, including many discussions phone and email exchanges with technical support from HP, they finally sent me a replacement printer.  It works as advertised right out of the box.  I don't know what was the underlying problem, but the fact is that he couldn't be corrected with one of the solutions proposed in the discussions on this forum.  Apparently, there's HP printers out there with a lack of internet connection has nothing to do with a solution that is configurable by the user.  If you have one, then you will need to replace your printer.

  I can't thank HP for that.  They tried my patience and tenacity of the months before offering the only real solution.  They must know their products better than that and should have replaced my printer several months ago.  That being said, the tech person with whom I had most of my relationships, it was a nice guy.  I expect he's working under an edict on exhausting all possible tactics before agreeing to replace the unit.

  Good luck!

• HP LaserJet Professional P1606: HP Web Services Installation - connection error. Check the Internet connection.

  I try to activate the Services Web of HP but connection error. Check the Internet connection. .

  I use the static ip address with the address of the preferred DNS: 8.8.8.8 and 8.8.4.4 and it does not work.

  I changed to DHCP as it does not work.

  I have a ZTE home modem router connected to the printer.

  The link below should help you.

  http://h30434.www3.HP.com/T5/user/viewprofilepage/user-ID/2585903

  Kind regards

  Oliver

• "Connection error. Check the Internet connection. "When you try to enable Web Services on HP 1606dn

  Error message "connection error. Check the Internet connection. " When you try to enable Web Services on HP Laserjet 1606dn.

  Operating system: Windows 7

  Thanks for the help,

  Howard

  Last UPDATED 21/07/13: after upgrading the firmware to the latest version, I could enable web services. Great help has this video: http://www.youtube.com/watch?v=Q5gpIGZXDXw

  Thanks for trying to help.

  In my case, it did not help.

  I followed the instructions on this video: http://www.youtube.com/watch?v=Q5gpIGZXDXw.

  The key was the update of the firmware, I think.

  Walter

• Microsoft fix Setup error + check the internet connection?

  I try to install the microsoft fix it and when the installation starts there was a mistake that check the internet connection

  Hello

  ·         What fixit you try to install on the system and why?

  ·         You are able to access other Internet sites without any problem?

  ·         What is the exact error that you are experiencing?

  I suggest you to check if you have turned on the proxy server. Follow the steps mentioned below.

  1. in the Internet Explorer Tools menu, click Internet Options, click the connections tab and then click LAN settings.

  2. in according to groups of servers Proxy, click to select the use a proxy server for your LAN check box.

  3 address , enter the IP address of the proxy server. (Note: Please try the same content with your "work PC' type)

  I suggest post you your query in the Fixit support forum to get help.

  Microsoft Fix it Center - NOT for general support questions

  http://social.Microsoft.com/forums/en-NZ/fixitcenter/

  Also, I suggest you to refer the links below.

  http://social.Microsoft.com/forums/en-NZ/fixitcenter/thread/0c5b0e4e-341F-468d-B2E4-6709c5df0198

  http://social.Microsoft.com/forums/EU/fixitcenter/thread/6278e447-a2aa-4380-9467-5e331d0723cf

• How can I check the internet connection?

  How can I check the internet connection after the launching application?

  Method or property with the value true or false.

  Thank you!

  You don't have to see the 2nd answer, discuss blackberry.system.hasDataCoverage

• Laserject 1606dn error, "connection error. Check the internet connection. "during activation ePrint

  I try to turn on my LJ 1606dn ePrint. I downloaded and installed the firmware and that is okay. I went to the Web Services tab to get the code to register the printer. When I click on 'Activate' in the ePrint section, I get the error, "connection error. Check the internet connection. "My connection network and internet are working properly. Am I missing something? I need to open a port on my router? Is there a special song, I need reciting under the full moon while sacrificing a live chicken?

  Thank you

  Joe

  jfusco,

  If you have an IP address manually, assigned to the printer:

  1. Enter IP address of the printer in the Web browser address bar and press ENTER.
  2. Go to the network tab and the IPv4 Configuration of the page.
  3. In the DNS server settings, the entry in your domain DNS servers or put IP of the router Address in the preferred DNS server and 0.0.0.0 or 8.8.8.8 in the section auxiliary DNS server and apply the changes.

• Qosmio F60/05-PXE-E61 Media failure, check the cable of

  Hi, I have a new laptop Qosmio F60/05 which is now having problems starting.
  I bought on 29/12/2010 and used again except for the internet.
  On a couple of occasions, an error has popped up saying that the computer has detected movements of hard drive...

  I don't remember the rest of the message, but it's usually after I took the laptop on the coffee table for sofa etc.
  Only now do I think it's a problem because portable computers are designed for portability and should be able to deal with this kind of movement.

  Perhaps this error and the following are connected?
  This morning I turned on my laptop and it took a while to start. Then the error messages came up saying that she had to restart and to restart the "Media Failure-check cable PXE - E61" error message "PXE - M0F outgoing PXE ROM" "Insert system disk in drive."

  I'm not tech savvy and don't know what to do now that no system disk provided with the laptop.

  I have read other forums on other sites that say it is a hard drive problem. Is this true and can I consider warranty return?
  I can't believe, I get questions on a laptop the week old and I'm pretty bored...

  Help, please

  Lauren

  Hello

  Message PXE means that laptop would not boot from other sources, but tried to boot from LAN. But LAN startup was not possible and that's why you have received this message.

  In most cases the HARD drive was not found and so the laptop going at the start of LAN. In your case, I would recommend accessing the BIOS and check the status of the HARD drive.

  But if you start windows in safe mode or in other modes, this means that the HARD drive is ok.

• my computer won't past the splash screen. She claims system not found, check the cable. I have windows on my Acer laptop base.

  After I press start, the splash screen appears briefly, then a black screen stating:
  Pre-boot EXecution Environment (PXE) v2.1
  PXE - E61:Media test failure, check cable
  PXE - MOF: exit ROM PXE.
  Operating system not found

  ·       Try to remove your hard drive and unplug the cable.  Then re - attach the cable and re - install the HDD.  Somehow, the cable may have come loose and it may solve the problem.  If this does not work, follow these steps:

  Do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not resolve the problem, try the following:

  To run the Bootrec.exe tool, you must start Windows RE. To do this, follow these steps:

  1. put the Windows Vista installation disc in the disc drive, and then start the computer.

  2. press a key when you are prompted.

  3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.

  4. click on repair your computer.

  5. click on the operating system that you want to repair, and then click Next.

  6. in the System Recovery Options dialog box, click command prompt.

  7. type Bootrec.exe, and then press ENTER.

  
  Note If rebuilding the BCD does not resolve the startup problem, you can export and delete the BCD, and then run this option again. In doing so, you ensure that the BCD is completely rebuilt. To do this, type the following commands at the command prompt Windows RE:

  ·        bcdedit/export C:\BCD_Backup

  ·        c:

  ·        Boot CD

  ·        BCD attrib s h - r

  ·        Ren c:\boot\bcd BCD.old

  ·        Bootrec /RebuildBcd

  Good luck and I hope this helps!

  Lorien - a - MCSE/MCSA/network + / A +.

• Lenovo ideapad laptop z500 won't start without the cable connected

  Hello

  My z500 cannot start without power cable is plugged. In general, a few seconds after I saw the lenovo logo, the system stops suddenly as if the battery was removed.however, if on that I connect the cable to the laptop and power, all right, I can enter in windows 8, or ubuntu, after I enter the OS, I can disconnect the power cable without any battery problems.the is healthy and can last for more than 2 hours. Is it someone has an idea what is the problem and how to solve

  so far, I have tried the following methods:

  1 update BIOS

  2 firmware update of the battery

  3 reset the BIOS

  None of them worked for me

  Hi maoxiaomin,

  Thanks for posting back.

  Sorry we could not be of additional help and please contact our service, if you need more help please do not hesitate to post in the forums.

  Concerning

• How to check the network connection in bb os 4.6?

  Hello

  I know that there is a demo of blackberry os 5 api network.

  If I want to check the connections as in the os 5 (TransportInfo).

  What should I do?

  thankx.

  Hello

  sonicboomboy and peter both of you thank you.

  below the link help me solve my problem.

  Link

  thankx.