Satellie Pro A120 - network adapter wireless not recognized by any operating system

Similar Questions

• Satellite P300 PSPC4E - new battery is not recognized by the operating system

  Hello

  I bought a new battery and it is not recognized by the system
  Satellite p300-PSPC4 win7

  drivers ok
  OK magazine

  The battery is always fully recognized and fully supported. I tried several methods to try to load but nothing happens

  the battery icon is present

  Thank you

  Hello

  Because your old battery is always recognized, I think you bought the battery is not compatible.

  That's why you should buy a compatible battery recommended by Toshiba.
  I think you can buy this Toshiba ASP.

  Welcome them

• Satellite P100: Memory Stick Duo Pro with MSD adapter is not recognized

  When I insert the CSDP in my Satellite P100-473-multi card reader - Vista preinstalled - (using an adapter MSD), the removable media is listed in the Solution Explorer, but the card cannot be read.
  With a 32 MB card, he pointed out that the card needs to be formatted first... but correct data are inside and must be visible.
  With 1 GB card, it reports that card is first inserted...

  Did anyone experienced this problem?

  Hello

  Have you checked the user manual you?
  Take a look at Chapter 8!
  There is information that the card reader is supported only SD; MMC; MS; Cards MS Pro and xD.

  As you can see that it supports the Memory Stick Pro, but not the Memory Stick Pro DUO!

• Qosmio F50 - 12W - processor Quad HD not recognized by the operating system

  Hello

  I can't find my Quad Core processor in my device manager. It is not in the sound, video processors... devices were it suppose to be. (or as an unknown device). As it is disconnected or something. Is it a hardware error or there is a special way have recognized this system hardware. Even that I installed the driver says--> not found material, connect the material at any time in the future.
  My Spec:
  F50 - 12W - Vista32 Home Premium

  Thanks in advance for your advice.

  Are - this you laptop preinstalled with Toshiba recovery image?
  You can view Toshiba HD console in the windows sidebar?

  As far as I know for the coprocessor must be preinstalled Driver TOSHIBA Quad Core HD.
  Strange, it's that I can't find this driver for Vista on Toshiba download page. For Win7, the driver is available.

• Wireless network adapter does not work on my Satellite A200

  Hello

  My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

  What can I do?

  Details:
  Typ: Atheros AR5008X Version: 7.2.0.164
  Laptop Satellite 200
  PSAE6E

  Please help me!
  Thanks in advance!

  Phil

  BIOS bug? I don t think so

  First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

  After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

  I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

• Wireless network adapter could not be activated

  My laptop also did EXACTLY the same thing in the morning today.
  No effect with the wireless on switch on the computer. The light is always red. Last night an automatic update that happened (update for windows Vista (KB955430) 09/05/2009 09:03), which cannot be deleted. I don't know if this problem is related with the update.

  My laptop is HP Pavilion dv6439nr.  Running Windows Vista Home Premium (Service Pack 1).  Wireless adapter is "broadcom wireless 802.11 b/g WLAN PCI" that is gone now.

  Windows network diagnostics shows "this computer doesn't have a card installed and configured wireless network."

  HP Home Network Center shows "Wireless status: disabled; When I try to enable wireless LAN, it shows "wireless network adapter could not be activated.

  I tried to scan and reinstall the driver but the device does not appear.

  The wireless router works fine with other laptops.

  If anyone has a solution it would be greatly appreciated.

  Thank you

  Alboury,
  It seems at this point that your wireless network adapter has a hardware problem.  Check out this troubleshooting guide step by step on the HP Pavilion support web site.  If you can't get your active wireless card, you will need to contact HP or repair HP authorized repair for hardware Center.

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00813382&LC=en&DLC=&cc=us&product=3619365&rule=5493&lang=#WLANStatus

  Let us know if we can provide assistance.

  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Wireless network adapter is not installed and configured

  I have recently re installed windows vista for my laptop dell inspiron 1545. I am not able to connect to wireless internet, it says that the wireless network adapter is not installed and configured. How do I install it and where can I get the wireless network adapter. I have a cd or anything for it. Thank you

  You can get in trouble with your device drivers, firmware and/or software.  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you shouldget from Dell for the wireless adapter at all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html. > http://support.microsoft.com/kb/244617.

  The adapter is inside the laptop.  You don't need to do something with it to install it.  Install the drivers, firmware or software for it and your version of Vista from Dell (all that apply) "install".  You must then go to start / Control Panel / Network and sharing Center and configure the adapter with the appropriate parameters and to establish the appropriate network connections.  This will take place in settings required by your ISP, and maybe your router or modem (so you may need to contact them if you don't know the settings).

  Here are the procedures for Vista with Windows7 network layout that can help:http://www.windowsnetworking.com/articles_tutorials/Windows-7-Understanding-Network-Administration-Configuration.html.

  Here is another article on home networks (with several links to related articles which must all be considered - as well as others, you will find in the related articles) to help you better understand the home networks: http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.  If it's for Vista, much of it applies to Windows7 (although there may be some differences that should be addressed in the previous article).

  Here is an article on the networking of the different versions of Windows:http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows.

  Here is a tutorial on how to set up a home network (including a wireless)-click on additional links for more information that may be helpful:http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.

  Here is an article on troubleshooting network connections wireless (with links):http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-network-connection-problems.

  Here's a long guide on wireless internet connections in Vista:http://www.techwarelabs.com/guides/misc_mod/vistaconnection/.

  Here is an article on how to set up wireless internet in Vista:http://www.clpgh.org/usingthelibrary/technology/wireless/WindowsVista.pdf.

  As I am unsure of your Setup, I've included several items that can help depending on how you are setup.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• EliteBook 8440p: network adapter does not

  Help. just got a laptop second hand from a friend and after vista installation my network adapter is not working / available. I'm not savvy computer, please help

  Hello:

  You need the driver for the ethernet controller.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4095874&swItemId=ob_101142_1&swEnvOid=2101#

  How to disable the card wireless using the key, you must read the user manual.

  I have a 6930p which was the model that preceded the 8440p and there is a black band with a few icons lit above the keyboard and mine has a blue icon wireless.  If I touch that, it becomes orange which means that the wireless is turned off.

• Cannot install WIndows XP SP3 - wireless adapter does not work with any package of service beyond 2.0

  original title: wireless adapter does not work with any package of service beyond 2.0

  I have an AirLiink 101 wireless adapter.  Anyone know how to change the service pack 3.0 for me to update my Windows XP?   Can not install 3.1 without losing wireless connection.

  Thanks for any help.

  If you are on a wireless connection, try to switch to a wired connection and try the download with Internet Explorer.

  UTC/GMT is 06:49 on Wednesday, April 11, 2012

• Network adapter is not found.

  Reinstalled Windows XP installation CD. Network adapter is not found. How to install network card and the driver on the CD?

  Hi Malek,

  You are able to find it in the Device Manager... Click Start-> settings-> Control Panel-> system-> hardware-> Device Manager. Do you think any yellow question mark next to your network adapter? If so, double-click the network adapter, select drivers updated, click Advanced, and then point installation on your CD/DVD.

  If he won't take the CD/DVD file, check your CD/DVD maybe executable installation package, you must click on the exe file and it will automatically install the drivers for you.

  I hope this helps.

• "The network adapter is not correctly configured to use the ip Protocol" problem on Vista

  Hello. My PC has recently came across this problem "the network adapter is not correctly configured to use the ip Protocol", every time I click on diagnose & repair. I don't know how to fix it. Please help, thanks in advance. Magic

  Hello X-x_MaGiC_x-X,

  Thank you for visiting the website of Microsoft Windows Vista Community.

  Try the rest of the stage in this article:

  System restore points are created automatically when the following occur:

  • When you install a new application or driver.
  • When you uninstall or install some programs.
  • When you install new updates
  • Automatically on a daily interval
  • Manually by creating a.
  • If you choose to use system restore to restore to a previous restore point, System Restore creates a new restore point before you restore a previous state in case something goes wrong. If you are restoring to a previous state in Mode without failure, a restore point will create for the current state.

  So that the restoration of the system to work, you must have 300 MB of free space for each hard disk that monitors the system restore. System Restore will also use up to 15% of disk space on each disk that it monitors. That hard disk space runs out, older restore points will be deleted as newer ones. It is also important to note that you must be logged in as an administrator in order to use the system restore. Now that you understand the basics of the system restore, you must continue to the next section to learn how to use it.

  Restore Windows Vista to a previous state

  In the case of a problem on your computer that cannot be solved by normal means, you can restore your computer to a previous working state. To do this, you need to start restoring the system so that you can choose the restore point to restore. If you currently have Windows Vista boot problems, you can use the system restore in Windows recovery environment. Instructions on how to do it in this tutorial can be found: System Restore using the Windows Vista recovery environment.

  If you can connect to Windows Vista, you must follow these steps.

  1. Close and save any documents that you have opened.
  2. Click the Start button to open your Start Menu. The Start button looks like this:
  3. When the Start Menu open click on the menu option all programs.
  4. Click once on the Start Menu Accessories group.
  5. Click once on the System Tools Start Menu group.
  6. Click once on the icon of the system restore. After you click the icon, if a user account control window opens, click on the button continue.

  You will now be on the screen as shown below in Figure 1 system restore. From this screen, you can specify the restore point that you want to restore.

  1 screen of system restore

  By default, Vista will be already selected the restore recommended option. This restore point is one followed a new pilot program, or update has been installed. If you do not want to use this restore point, you can click on the button next to start the restore process. On the other hand, if there is a more recent restore point that you want to restore you should select choose a different restore point and press the next button. This will bring you to a screen, as shown in Figure 2, which contains a list of all available restore points that you can restore.

  2. the list of available restore points

  You must select the restore point that you want to restore, and then press the button next to start the restore process. Vista will display a window showing your selected restore point and asking you to confirm that it is that you want to restore.

  3. confirm the selected restore point

  If you want to select a different restore point, press the Back button. Otherwise, you can press the Cancel button to exit the system restore or the button finish to begin the restore process. If you have selected finish, Vista will display a second prompt asking you to confirm that you want to continue restoring.

  4. second Confirmation

  If you are sure you want to restore, then press the Yes button. Vista will now log you off the computer and start the system restore process, as shown in Figure 5 below.

  5. restoration of a restore point

  When the restore is complete, your computer will be restarted and when Vista starts it backup will be restored to its previous state. When you open a Vista session for the first time after the restore, you will see a message indicating that the restore was successful.

  6. system restore was successful

  If there are problems with your computer because the last restoration, you can return to your previous settings to ebb in the system restore utility and select Undo system restore by pressing the next button.

  7 undo the last system restore

  Your computer should now work correctly again.

  With the help of the restoration of the system in the Windows recovery environment

  Manual creation of Restore Points

  As mentioned previously, it is also possible to create manual restore depending on points. Some popular designs to create manual restore points are when you have your computer configured perfectly and I would save the State in case of problems in the future. To create a manual restore point, you must follow these steps:

  1. Click the Start button to open your Start Menu. The Start button looks like this:
  2. Click on the control panel menu option.
  3. Click the option menu system and Maintenance.
  4. Click on the system menu option.
  5. Click on the System Protection in the list on the left.

  You will now be at the System Protection tab in the system control panel. This tab allows you to enable and disable the system restore as well as making the new manual restore points.

  8. the System Protection tab

  To create a manual restore point, you must click on the button create. When you press this button a prompt asking you to give a title to this manual restore point.

  9. Enter the manual restore point title

  Type a title for the manual restore point and press the button create. Vista will now create a restore point manually and once finished, post a notice that it was created successfully.

  10. Manual restore point has been created

  Now that you have finished doing the manual restore point, you can close the system window.

  Try to download the correct and up-to-date drivers.

  This should solve your problem.

  Let us know if these steps solve your problem.  I hope the information is useful.

  Kind regards

  Anthony
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• The network adapter could not establish the connection using the external ip address

  Hi team,

  Please look in the attached files.

  I installed db 11g on my desktop machine (Windows 7, with a local network) and then I created a data source connection in tomcat which was also in the same system and then I deployed my sample web application, everything works fine, I am able to access web applications.

  But once that I kept my system with external IP address (excluding local network of my company), oracle gives these following errors when tomcat start

  Here is the following URL will display the error during the startup of tomcat.

  The network adapter could not establish the connection,

  In these two files, listener and tnsnames ora ora, need to change the configurations if I change the Ip address of the system?

  even I tried my address keeping external Ip instead if host in these two configuration files, yet this does not work.

  any help would be greatly appreciated!

  Thank you.

  Because as I explained - your listener is listening on localhost only. localhost is never accessible to another machine.

  Stop your listener, change the listener.ora to listen to on the real machine name and start the receiver.

  In addition, your tnsnames.ora points to localhost...

  Stop using localhost, unless you only want things to work on the same machine.

• Cloud of Console 12.1.0.4 - IO error: the network adapter could not establish connection to access Instances of the ASM

  Hello

  Using the last version of the Console 12.1.0.4 cloud. I discovered a RAC cluster consisting of two nodes.

  And if I "try access the Cloud Console ASM instances will fail with this error:"

  IO error: the network adapter could not establish the connection

  The connection descriptor has been

  (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = tcp)(HOST=rac1-vip.localdomain)

  (PORT = 1522))) ((CONNECT_DATA = (SERVICE_NAME = + ASM1) (INSTANCE_NAME = + ASM1 (SERVER = DEDICATED))(UR=A)))

  My env is:

  Console of clouds on: release of Red Hat Enterprise Linux Server 6.6 (Santiago)

  Database Rac: Red Hat Enterprise Linux Server release 6.5 (Santiago)

  Someone knows how to solve this problem?

  Thank you very much!

  Arturo

  (1) what is the user id you are using OEM fior?

  The user id should have Sysdba and should not be in the role SYSASM.

  (2) in order to check your port

  In server, in the gate of the House, listener, lsnrctl status--> Verify asm instance listed on your listening port.

  Summary of endpoints listening...

  (Check that the PORT and IP information is correct)

  Instance '+ ASM1' READY State, has 1 operation for this service...

  (3) in addition, connect to asm and check the connection

  Show u local_listener and entered into OEM parameter details are correct.

  (4) OEM, I think you add Cluster_ASM.

  Oracle_home_path--> you're grid House

  username--> with sysdbarole

  --> Sysdba role

  Cluster_name--> $GRID_HOME/bin/cemutlo - n

  Service name--> + ASM

  ADD

  NAME: INSTANCENAME

  -Home: HOST1

  listener_HOST-->< show="" parameter="" local_listener=""> exit

  PORT-->

  SID- + ASM1

  Concerning

  Krishnan

• I/o error: the network adapter could not establish the connection: connection to oracle database

  Hello

  I am not able to connect to the Oracle SQL developer database. I said / 0 error: the network adapter could not establish the connection.

  I started the listener, but what I see is, it points to a different IP address instead of the IP address of the host. How to change the name of host or IP address.

  I see that it points to the host name in listener.ora.

  Attached the screenshot

  

  Can someone help me solve this problem?

  Thanks in advance

  What he says is the listener.ora file is not necessary to start the listener.  If you rename, then start the receiver, then start the db, after a minute or two, the db should automatically register with the listener and then you can make a tnsping or otherwise connect to the database through the listener.

  I'm not entirely sure what's going on with your image, but I can't help but wonder if somehow something is not what you expect with the investigation period, whenever it starts.

  So use lsnrctl status lsnrctl services to see what the listener is the situation and tnsping and ping from the client to see what he thinks.

• IO error: the network adapter could not establish the connection

  I'm configuration 11.1.2.3 on Windows 2008 using the Oracle database and when I try to configure connection services database and shared registry associated with the House I get the error "IO error +: the network adapter could not establish the connection +" all by filling in the details of the database. Windows Firewall is disabled, database is able to connect through SQL Plus am running, listening for the database service is running and the name of SID and the server have been provided properly. I even used localhost, apart from the name of the server providing the servename and ORCL is the SID. Any suggestions please?

  Usually, if I install on a Virtuelle/portable Windows machine that does not have a fixed IP or a dns entry I install a card closure before installing Oracle and have never had problems, it is established in http://docs.oracle.com/cd/E11882_01/install.112/e24186/reqs.htm#BABFHCJG

  See you soon

  John
  http://John-Goodwin.blogspot.com/