Satellite 1800-712 does not start with the new HARD drive

Similar Questions

• SMU 8108 does not start with the new hard drive

  Hello

  I am currently using SMU 8108 with SMU-1062 q.

  The previous record was borken, so I had to install a new hard drive.

  The new hard drive is fommatted as NTFS format, and it is currently mounted on 8108.

  Unfortunately, I don't have recovery disk available to the general public so I am trying to install Windows 7 on a blank hard drive.

  When you start, the LED OK PWK light is all the time, orange DRIVE LED turns on for a few seconds only when I turn on the switch.

  LabVIEW RT switches are all off, I cleared CMOS several times to the Board of Directors, but the screen does not show anything.

  I tried to use my DVI monitor with any other device as well, and it worked, so there is no problem with the monitor.

  In addition, I tried to go in window safe mode by pressing F8 or Del it didn't work, so I can't see anything on the screen when his kick upward.

  I tried to put a lot of information I can it will be very appreciated if you can help me with this problem please.

  You said that you can't in Windows safe mode, you have installed Windows on the hard drive?  Are you able to get into the BIOS of the controller?

  If you are not able to access the BIOS for the controller, it may be due to bad RAM.  If you are uncomfortable installing RAM and you have a few extra laptop RAM of the same type (I think it's the DDR3 for your controller) laying around, you can try to replace the RAM.

  Was your hard drive damaged through certain events, or it just stop working?

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• Satellite 1800-712 does not recognize my USB external HARD drive

  Hello

  I would really appreciate the help. I own a satellite 1800-712. I have receently bought a usb external hard drive for some extra memory (IE Toshiba MK4026GAX USB Device)

  When I connect it to my usb port it records any with the computer. The green light so there is power to the hard drive. The usb ports recognized of other fine features (a modem and memory stick)

  I tried the external hard drive on a desktop pc and it works fine.

  I have downloaded all windows xp service pack updates and updated my bios. Don't know what to do now.

  Please help and thank you in advance!

  Hello

  Although sometimes, I know that the OS is not able to recognize the external USB device, because the device external USB (HDD) consumes more energy than the 500mA.
  The USB ports provide 500mA power and if the device needs more power so it s is not possible for the Windows operating system to recognize the external device.
  You have an external power supply for the USB HDD? You should use it.

  Good bye

• Satellite L655-149: recovery does not work with the new HARD drive

  Satellite L655-149

  PSK1JE

  Windows 7 Home Premium 64-bit (factory installed)

  Recovery of HARD drive on drive D (factory installed)

  My old toshiba (MK5065GSX) 500 GB hard drive became too noisy and slow so I plan to replace it with the new drive hard toshiba (MK5059GSXP) 500 GB.

  I created USB Flash HARD drive recovery.
  When the installation is complete and Setup installs devices an error "Windows Setup couldn't configure windows to run on a hardware on this computer.

  I've updated the bios
  I loaded by default in the bios
  I changed the SATA AHCI mode to compatibility IDLE

  assistance in this regard will be highly appreciated

  Set the BIOS to the default settings and try again.

  With the installation of recovery, there is a problem: either it works or not. If this isn't the case, bad luck and the only solution for you is to order original Toshiba recovery DVD on https://backupmedia.toshiba.eu/landing.aspx

  By the way: do you use that stick of recovery for the first time?

• Satellite L30: CD player does not work with the new HARD drive

  Hello

  Just bought a new drive to HARD drive of 250 GB to transform my L30-115 has a home server.

  My problem is when both the new HARD disk drive DVD/CD-RW drive of origin are inserted into L30, the computer crashes and I can not even get into the BIOS (I have the latest edition).

  However, when I disconnect the CD player, system boots fine in a system of operating "plain" (command-line only) - BIOS recognizes very well and everything is fine. Idem: as I disconnect the HARD drive and connect the CD player, I am able to work (for example with a live linux system).

  The question is: * how to install a Windows operating system to a new HARD disk drive *? There is no option to boot from USB. What else can we do? I'm not going to invest more money into this old machine. I would like to install the Windows Home Server in there. There is no need to use the CD player later (all other operations will be performed by the network).

  Person not answering, so I'll do it.

  I was able to boot from USB external floppy drive, so the solution is to boot from external CD drive and install the system.

  It is not an exact solution, because the internal optical drive must be removed, so I'm looking forward to see updates to the BIOS level or other solutions for Toshiba.

• 1800 514 does not start with the new dvd/CD-RW drive

  My old dvd - rom on my toshiba s1800-514 drive was broken, so I had to replace it. I used an old teac as a temporary replacement cd-rom drive. but now, I bought a new dvd/CD-RW-drive combo (toshiba sd-r2612). but the laptop does not seem to post, I get the "toshiba" screen (when it says press f12 to select boot device). but it stops there and does nothing. I can open the player, it seems to be connected ok.

  Why won't it work? (only the bios setting which applies is one that I can't change...). the drive is nine ar so small chance it's already broken.

  What should do?

  Hello

  A few weeks ago one of my friends also had a problem with his replacement new drive. He wanted to move the DVD/CD player to a DVD burner.

  The only thing he had to do was change the master/slave settings!

  Goodbye Chris

• Satellite L30 10Y does not start with the new RAM modules

  Hello
  regged just with this forum I have a problem to upgrade memory.

  I read through a few problems of memory here and all users that it is a problem of memory comaptible. I got Hynix 512 MB RAM in my laptop and I bought 2 x 1 GB memory Hynix these two are match sticks to the installed memory, but when I installed my laptop wouldn't boot at all. It would only boot if I had a stick in both.

  I tried to switch ports top and btm and even when a stick was installed it says in XP, Vista and Windows 7 (yes I tried all systems) 896 MB of available space. I even tried to use my other Hynix stick, but he won't start and showed more stick of 1 GB (896 MB usable in Windows 7). After reading all the threads I wonder if it is a hardware failure or is there a fix in the world of Toshiba or perhaps in the world of Toshiba, the L series is almost obsolete and not worth to help people who unwittingly bought their goods.

  I apologize for being slightly down on Toshiba but a laptop that shows what he can work and is not a company should hold his hand up and say that Yes, there is a fault and help deal with the problem.

  You see 896 MB, because the rest is reserved for VRAM for graphics card.

  Sometimes RAM may simply be incompatible, because of incompatibilities of calendar or RAM chip/controller design differences.

  What speed and timings is your original RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  What speed and timings is your new RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  You can display this information using a utility called CPU - Z
  http://www.CPUID.com/cpuz.php

• Satellite L30-149 - does not start with the new RAM modules

  I bought RAM Kingston 2 x 1 GB modules. When I put a single module in my notebook - everything works fine. When I put the two modules - BIOS freezes and cannot start.

  I tried to combine my old module of 512 MB with 1 GB of Kingston, but in this case laptop detects only more great module (Kingston). So, I'm stuck with only 1 GB of RAM. In my notebook BIOS version is 3.10, and it's the last. I tested RAM modules in a laptop and each of them works fine.

  What should I do now? Help, please!

  Download and run www.memtest.org Memtest to test these Modules one by one.

• Recovery disks do not work with the new hard drive?

  Hello, everyone.

  I have a laptop HP (pavilion dv7-1245dx) and the hard drive is dead. I had never gotten to burn my recovery disks, so I ordered new ones from HP. When I installed the new hard drive and popped in the disk to reinstall the operating system, it gave me the error message:

  "This PC is not supported by the system recovery discs. You can continue to recover this system with these discs. »

  Error code: 0100-30 FC-3602-3603

  The original hard drive was a Hitachi, 320 GB SATA

  The new hard drive is a WD 500 GB SATA

  Any assistance anyone can give would be great. :]

  Thank you for your time,

  C

  EDIT: Trying to recover a Vista operating system

  For anyone who has the same problem, I found a solution. I cloned the original hard drive using the Clonezilla fallback option. After using Clonezilla to image on the new hard disk, the partition which held that most of the data of the laptop is not mountable, however the partition containing the restore partition was a perfect copy. I turned on the computer, hit escape to access the menu (for a list of options such as boot order, etc, which included an option for recovery), and then choose recovery option. While the recovery discs, I received from HP refused to work with the new hard drive, the Vista restored cloned recovery partition without flaw.

• Satellite 1800-814 does not start if the power adapter is plugged

  Hello
  I have a problem with my 3 year old, 1800-814.
  It all started with the sudden Windows crashes. He ran sometimes smooth, sometimes he just hung up. So I decided to reinstall the laptop. My problem is when it is plugged by pressing the power on button does not start the laptop. Just the green light is on nothing else happens. Sometimes it starts after a wait of 3 or 5 seconds. On battery it starts every time. What can I do? A defect material or just dust somewhere?

  Thank you

  Jens Grieger

  Hello

  It could also be something wrong with the electronic power supply on the motherboard.
  It s is not possible for the user to fix it. In such cases, the best way is to contact Toshiba service in your country.

• C870-19(r) satellite does not start with the new SSD

  Hello

  I will update the Toshiba Satellite C870 19(r) with a Pro 840 Samsung SSD, but it does not start.

  He said: not found system.

  Post edited by: joch333n

  None found system means that there is no system installed on the SSD drive...

  What you trying to do?
  You start from a disk in order to install the new system?

  In this case, you should disable startup secure in the BIOS.
  I also recommend moving from UEFI mode MSC!

• Satellite P100-257 does not work with the new drive HARD WD SATA II 320 GB

  Please could someone knows how to solve my problem.
  I bought new HARD drive to upgrade my Toshiba Satellite P100-257:
  Western Digital SATA II WD3200AAKS 320 16 MB
  (Originally was installed Toshiba MK6034GSX 60 GB HARD drive)
  When installing Windows XP (from Toshiba disk recovery or all other disks), when the Installer starts copying the files to the temporary directory HDD (after HDD format) encounter a problem like "cannot write files to the HARD drive.
  I tried to format the drive before installation (even to split to 2 smaller logical drives).
  Also I have updated the BIOS at 2009-03-04.
  But nothing changes.
  What is the problem?

  Hello

  It seems that the HARD drive has been recognized because you can receive the error message about the Master Boot Record.

  I think that there is something wrong with the partitions on the HARD disk.
  I put t know how you formatted the HARD drive, but I think that you must first reinstall the operating system on a partition in order to check the functionality of the HARD drive.

  Once you have started using the Windows XP disk, try to create more than one partition and this format to NTFS. Then follow the installation of the OS!

• Windows 7 does not start with the new msi motherboard

  Yesterday, I bought a new motherboard, processor and 8g of ram in my computer. After all what adjustment and replacement of my old motherboard with the new, I started my computer to find that Windows 7 unbootable not. Instead of windows 7, I get the screen click on BIOS II (2). The configuration screen allows me to launch Winki but not Windows 7 because it was not found. The motherboard came with a utility disk drivers msi and AMD chipset which, when inserted in my hard disk, loads up to Winki. This version of windows 7 (Home Premium 64-bit) came pre-installed with my old mother/computer(Thus, I do not have the windows 7 installation disk) card. Is there a way I need to activate Windows 7 on my new motherboard?

  Hello

  Well, you have some problems. First of all, with a new motherboard you need a new copy of Windows - not only the DVD, but a whole new product key must be purchased. It's just the terms of the license: a new motherboard is equivalent to a new computer, and each computer must have its own copy of Windows.

  So where you buy your copy of Windows 7, I would make sure that it came with a DVD image. Otherwise, you can tell us which version of Windows 7 you (will) actually buy, and we can send you a link to the copy of the DVD for this version of Windows 7.

  To purchase a copy of Windows 7 you can check Newegg.com, here: http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&DEPA=0&Order=BESTMATCH&Description=windows+7&N=-1&isNodeId=1 .

  I hope that answers your question.

  Kind regards

  BearPup

• computer does not start with attached external hard drive

  I have the 4540 s if an external hard drive is connected, it will not start.

  I have the internal hard drive set as master boot.

  The message that appears indicates Press esc, to enter the boot options, but which does nothing.

  I spent an hour with hp support-useless.

  I did a BIOS update - no help.

  All advice appreciated.

  Not sure what you mean about the reference of the warehouse.

  I've updated the USB ports and that solved the problem.

  Thanks for the reply.