Satellite 2450-114: DVD - RW no readable with the reader DVD DTS-6012

Hello

I bought some Verbatim DVD - RW (media code: MCC 01RW4X) but it cannot be read by the reader Toshiba SD - R6012 DVD to my laptop Satellite 2450-114.

However, I have the latest official firmware, i.e. the number 1334.
Is it possible to fix it?
Thank you
Best regards.

Can your laptop read DVD original (movies) or perhaps DVD-R blank?

Tags: Toshiba

Similar Questions

  • Pouvez Satellite 2450-114 read SDHC with the latest drivers?

    Hello
    Do you know if the Satellite 2450-114 windows XP home supports playback of the SDHC with the latest drivers and the maximum capacity supported?

    Thank you

    Yann

    Hello

    Satellite 2450-114 is a former, and in my opinion, it would not support the SDHC card using even the latest drivers why?
    Because the card holder is not in the software/driver, but this is a simple physical limitation (card reader)

    So I suggest to use an external USB card reader these drives are cheap and easy to use

    Welcome them

  • Satellite 2450-201: cannot use TV option after the new installation of the OS

    Hello

    I have a laptop toshiba satellite 2450-201.
    I've always had the TV OUT works well with my TV, use the right cable SVIDEO.
    I was able to watch divx movies in my TV using my computer.

    I had to format the laptop and installed windows XP again.
    After that, I can't use more TV-OUT option, so that the image of the laptop could be seen on television, I've always had.
    After that I updated display drivers, but the problem remains.

    Can someone help me?
    Thank you

    Hello

    How do you reinstall the operating system? Have you used the recovery CD?
    Usually after the reinstallation of the operating system from the recovery CD, everything should work properly.
    It is important that you can switch to the TV. In this case, you can use FN + F5.
    If it's not working so I guess that for display devices hotkey utility works or was not installed. Well, the alternative is to pass on the TV via the graphic properties. The TV option, you should find somewhere in the advanced options.

    However, check it and check if you have installed all the drivers.

  • I need to set my Adobe Acrobat by default when I open PDF files. I've updated my adobe reader software and it changed my settings to always open with the reader. I still want to open it with Adobe Acrobat DC

    I need my Adobe Acrobat DC value by default when I open PDF files. I've updated my adobe reader software and it changed my settings to always open with the reader. I still want to open it with Adobe Acrobat DC

    Hello

    For windows, right click on the PDF? Open with > choose default program > set Acrobat DC as the default PDF Viewer and click OK.

    You could do the same thing in the control panel.

    Concerning

    Sukrit diallo

  • To the Satellite 2450-101 DVD drive failure

    Hi guys again...

    I have another problem with my old laptop Toshiba Satellite 2450-101 which I hope you can help me with.
    The original DVD-rom drive - a Teac DW - 224th - went "off the radar" a couple of times a year and only re - appear in my computer after a re-boot, but he then quickly disappear again.

    It is curious that the drive is still listed in device as Manager works correctly.
    Would have to be a complete reinstallation to get it back again when the process would start over.

    Now during the boot process, a message appears at the top of the screen saying "error Eide...
    I bought a new replacement brown-box DVD - RW double layer drive PC World - a Sony IA2604H - and has installed but it's exactly the same thing but this time she is mentioned in as a 'CD-rom SCSI device' Device Manager... which is certainly not.
    In both cases, readers are completely dead and does not eject even trays.
    Needless to say, it's driving me crazy.

    Can you suggest anything?
    Thank you once again...
    JB

    You can boot from the bootable CD?

    If so, then try to remove the upperfilters and lowerfilters:
    http://support.Microsoft.com/default.aspx?ID=314060

    If you cannot start from the CD, then either:

    (1) the ODD or another component of the motherboard connector is defective / in bulk.
    (2) the original Teac ODD is defective, and the new Sony is not compatible (has the wrong master/slave settings)

  • Satellite 2450-201: is it possible to upgrade the P4 to Athlon processor?

    I have a satellite 2450-201 and it came with petium 4 I want ypgrade to the athlon 64 x 2 will be this possible upgrade for my laptop?

    No, it is not possible.
    The Pentium uses different fixing like the athlon.
    In any case the portable technology is different because the desktop PC simply and miniaturization make these updates impossible

  • Satellite L655-149: recovery does not work with the new HARD drive

    Satellite L655-149

    PSK1JE

    Windows 7 Home Premium 64-bit (factory installed)

    Recovery of HARD drive on drive D (factory installed)

    My old toshiba (MK5065GSX) 500 GB hard drive became too noisy and slow so I plan to replace it with the new drive hard toshiba (MK5059GSXP) 500 GB.

    I created USB Flash HARD drive recovery.
    When the installation is complete and Setup installs devices an error "Windows Setup couldn't configure windows to run on a hardware on this computer.

    I've updated the bios
    I loaded by default in the bios
    I changed the SATA AHCI mode to compatibility IDLE

    assistance in this regard will be highly appreciated

    Set the BIOS to the default settings and try again.

    With the installation of recovery, there is a problem: either it works or not. If this isn't the case, bad luck and the only solution for you is to order original Toshiba recovery DVD on https://backupmedia.toshiba.eu/landing.aspx

    By the way: do you use that stick of recovery for the first time?

  • Satellite Pro P200 - 1KE Vista loses contact with the second internal HARD drive

    Vista Business SP2. I have a Satellite Pro P200-1KE, with two 160 GB drives: a Hitachi configured as C: (operating system, programs, etc.) and E: (data, other programs). The second is a Toshiba MK1637GSX. This little about it and nothing of any importance and is normally configured as d. Unfortunately this hard drive has now become invisible to Vista, although it is still recognized by BIOS and Device Manager. In managing computer does not appear in the list in the upper pane, it comes without a letter from reader below. I have tried everything I know to get recognized, including the following:
    (In no particular order):

    * Remove computer - managed, reset as a single Volume: it always fails
    * Reformat to NTFS using Linux GParted or utility disk Linux (via a USB stick with Linux ice Peppermint on that nerd), sometimes combined with the restoration of the system - it works, but only for a single session. She always disappears again when you restart
    * Remove the driver from Device Manager and pointing plug-and-play with Windows System 32 and Windows Update - which seems to return the driver - but does not recognized disk, unfortunately
    * Meanwhile, throughout all this, Vista insists on finding a driver for "unknown device" that she sometimes found and (allegedly) installs and sometimes find one fails to install.

    Bah!

    Anyone know anything else I can try - preferably without having to reinstall the entire operating system, or run the risk of using Toshiba Hardware Setup that does not seem to come with all the instructions and enigmatic, who wonder if I want to delete stuff 'selected', without showing me what kind of things I am alleged to have selected for removal!

    Best
    David

    If this second HDD is not so important to try to start the original installation disk Microsoft (Vista or Win7) to see if the second HDD will be recognized for the installation procedure.
    You can also try to install Win7 on this second HDD to see if the installation is correctly finalized. Later, you can check if you can start the second HARD drive preinstalled OS.

    Test just to see if this problem is related to Vista only.

  • Satellite A110 - switch WiFi does not work with the new WiFi card

    Hello everyone

    I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

    New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

    Help, please

    Hello

    Do you have also enabled the WLAN functionality by pressing FN + F8?
    Check it!

    In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
    So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

  • Satellite A100-225 keeps freezing and crashing with the new HARD drive

    Hi all

    I have a Satellite A100-225 with a 100 GB SATA Hitachi drive I int it that recently started showing bad sectors. Then I bought a Hitachi 320 GB SATA II drive to replace it. I tried the drive and it was recognized right away, so I didn't need to change the SATA speed. I ran the restore a disk installed newest. The problem I have is that the computer keeps freezing and crashing with the new drive. It takes a lot of time to load up when turned on and there is a noticeable to untermittant delay when you drag the cards around solo.

    I tried to run the Hitachi drive test and it comes back fine. I also tried to turn the SATA speed of the drive down from 300 to 150 via the firmware, and although I saw a slight improvement, it is still not right.

    I talked to Hitachi and they say that he could not be 100% compatible, so the problems. Someone at - it else sucessfully set up a replacement for this notebook drive and if so what make and model. Has anyone else had simular problems?

    Thank you

    Years ago, I've updated yet more former Satellite M70 with SATA HDD (270 GB if I m remembering well) and everything was fine.
    In my view upgrade with SATA HDD normal shouldn't be a problem. Do not SATA II because it will not work faster.

    I can't say for sure, but there must be a compatibility problem.

    Let's see if someone else had better luck with the upgrade of the disk on the Satellite A100.

    Have you checked this forum with advanced search option? Maybe you can find some old NET on upgrade the HDD on A100.

  • My Satellite A100 does not support SDHC cards with the internal card reader

    Hello

    My Satellite A100 can't stand my sandisk 4 GB SDHC.
    'normal' SD cards are not a problem with the internal card reader, and there is no problem with the 4 GB sandisk SDHC card using an external card reader.

    is there a software solution?

    regrads,
    Itock

    I don't have the time to read the manuals for your model of laptop users, but can be registered to all supported cards. I guess SDHC not registered and not supported.

    I don't know what you mean with the software solution, but as far as I know, update for multimedia card reader is not available.

  • Can I downgrade Satellite C875-13F of Win8 to Win7 with the same license?

    I bought a Satellite C875-13F in hury with 8 to WIN, but I would go back to win7. Is this possible with the same license code?

    With greetings, Aart

    Hello

    Check out this Microsoft page to understand the downgrade right:
    http://www.Microsoft.com/OEM/en-GB/licensing/sblicensing/pages/downgrade_rights.aspx#fBid=6jf3dZU2VW0

    Windows 8 * Pro * includes downgrade rights to:
    Windows 7 Professional
    Windows Vista Business

    I think you win 8 and is NOT Pro... so you canoe downgrade... you must purchase a license for Win 7

  • Satellite X 200-20 sec runs slower with the new motherboard

    I wonder if anyone can help - under warranty I just got a replacement motherboard. (Before replacing the computer turned off within 10 seconds of startup). Replacement of the computer being runnning to about 90% of the speed that it was working before replacement. I spoke with the support from Toshiba claiming that without "concrete facts" on the speed there is nothing they can do (ie. they book in). In a way, it's just, but this is just simply not as good as before and various tests I did (which they claim to be subjective) always show that the computer is slower.

    Toshiba support really like the performance index Windows (WEI), I currently have like 4.8 - I think it's the same as it was before the replacement - but I've read that even if it is not that reliable. Can anyone with a 200-20s X please tell me their score of WEI and a 3DMark 06 score?

    After replacing the motherboard I also got a new disc (BD - ROM) on E: of course is not X 200 - 20s model Blu - Ray so means that the motherboard is different from the original, although the part number is apparently the same (according to Toshiba support).

    I would like to know if anyone else has had a similar problem, and if they were able to find a solution. I am aware that the warranty expires in November and therefore make things quickly if something can be done.

    If you can help, let me know.

    Thank you very much!

    Hello

    Have you tried to change Windows settings power management?
    To do this.
    The power of Windows Vista and Win 7 management controls the CPU performance.

    For more information, see this Toshiba HowTo:
    http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=41

    Welcome them

  • Satellite A300-1MZ - Smart tool recognize problems with the drive

    Hi all...
    I have a * a300-1mz * I * a problem with the hard drive *.

    [This | http://img96.imageshack.us/i/diskinfoe.jpg/] is the _screen to a s.m.a.r.t. pens (* Disc 3.3.0 * Info) who acknowledge some problems with the disk.

    Can I send the laptop as collateral for a free replacement of the same disc?

    Among other things, sometimes * the computer freezes * no option to manually turn off the laptop (I think it always comes from the same disk):
    the screen stays fixed and 'Win Vista' does nothing comands.
    same "ctrl + alt + delete" Task Manager does not. The disc indicator light remains lit, but itself no longer believes it works

    Hello

    > Can I send the laptop as collateral for a free replacement of the same disc?
    If the authorized service provider can notice this problem too, you can get a new HARD drive for free. The ASP will order it and swap it out. It is a free procedure if your laptop is under warranty.

    > sometimes the computer crashes
    The HARD drive is perhaps the reason for this?
    Contact a service provider authorized giving them all the details and information. They can fix that also. :)

  • Satellite - black screen and can't restart with the recovery disk

    I have a black screen and can not restart with the restore disc but it seems to be.

    I find this odd, I can't ask Toshiba direct on my problem, but I have to wait for one nature in the heart of my problem or give me a helping hand

    Hey,.

    This means that you can see anything on the screen of the laptop or only if you try to start with the recovery disk?
    You can start Windows or access the BIOS?
    You must post a few more details, otherwise we can t help you :(

    Furthermore, Toshiba is not your first contact, you should ask an authorized service provider. They can help you too! :)

Maybe you are looking for

  • iPod Classic 80 GB volume will not go up

    Our 80 GB Classic is no longer opens in iTunes and disk utility in OS X shows that the volume doesn't go up. The iPod has been managed manually on several of our computers over the years, and the last backup was performed age there is.  DiskUtil is u

  • Satellite A200 PSAF6A - cannot find drivers

    Satellite A200 PSAF6A-07G01N I can't find the download of the driver page.There is probably one. If there isn't one, what can I use instead? Thank you.

  • Photosmart Plus B209a connects to the router

    I installed my printer and I use printer if I plug it into my laptop, but not with wifi.  Keeps telling me that the printer is offline, but the blue light is on.  When I installed to my newer computer, the Setup program would not show me B209a which

  • My 5510 not scan to computer. It is said that it is not connected.

    I have a 5510 all-in-connected to a HP with Windows 7 computer.  The printer will scan to print, but will not scan to the computer.  I downloaded the 'Doctor' program, but it didn't fix the problem.

  • Get the width of a font

    I'm writing my own custom TextBox that has a border and resizes based on the font size.  i.e. the constructor would pull a numberOfCharaters parameter and it will determine its preferred width using the font size.  This works great in height: public