Satellite A100-237 (PSAA9) crashes after update BIOS 5.10

I have a psaa9 A100-237
I recorded my book and went in the updates section
There was an update of the available BIOS, I had version 2 before I updated to 5.10.

Now everything has gone well, but the laptop is restarted, it blocks every time on the start screen where the toshiba logo is displayed.
I can't log into BIOS, boot from the CD or anything.
When I press ESC black screen just showing bios version 5.10 memory pass and things, also written there is error TRM (TPM?) or not found.

I used the method of updating the bios windows and followed all the directions, wts the problem?

Hello

May I ask why you updated the BIOS?
You are 100% sure that you have updated the BIOS with the correct procedure and used the good BIOS?
Have you read the Description of the Toshiba BIOS update before continuing?

As far as I know the BIOS 5.1 has been released to use and install Vista on this laptop!
Hmm, maybe something goes wrong during the update procedure and, therefore, the laptop cannot load and start correctly.

Tags: Toshiba

Similar Questions

  • Satellite A100-237 / PSAA9 - how to enable AHCI (SATA Native mode)?

    Hello

    I have the Satellite A100 - 237 (PSAA9) and I would like to activate the AHCI (SATA Native mode). But in the BIOS there is no settings as AHCI or SATA mode.

    Is it possible to enable it in any other way (hidden fixing, utility sw)? Or only new special BIOS for this update (I have the latest 5.90) can solve this problem?

    Thank you for the answers.

    No response for the last 5 days. Of course, there is no special hidden parameter or BIOS. ;)

    As far as I know that there is no hidden settings and also no special BIOS. If something like that exists perhaps for technicians and non-public use.

  • Satellite A100 - 237 (PSAA9): I want to install the disk HARD SATA 3 Gbit/s

    Hi guys,.

    I have a laptop satellite A100 - 237 (PSAA9). I plan to replace the hard drive of 160 GB Momentus 7200.2 (SATA 3 Gb/s). My problem is that I can't find any information if my system will take in charge of SATA 3 Gb/s interface.

    Any help/information is much appreciated.
    Thank you...

    Hello

    I found the info on your laptop HARD drive interface is Serial ATA Rev. 1. 0a.

    Hope this info helps.

  • Satellite A100 - 237 (PSAA9E) - can I improve it with a new 320 GB HARD drive?

    Hello!

    I want to switch the hard disk of my Satellite A100-237. It is equipped with 80 GB Fujitsu, 5200 rpm, SATA. I want to install a new one - 320 GB, 7200 rpm, SATA. But I don't know is it supported.

    I tried to find information about the possibilities for this upgrade, I could not find anything.

    Thank you in advance!

    > I want to upgrade the hard drive of my Satellite A100-237. It is equipped with 80 GB Fujitsu, 5200 rpm, SATA. I want to install a new one - 320 GB, 7200 rpm, SATA. But I don't know is it supported

    Don't worry, buddy... I don't see any serious reason why would be supported not the 320 GB SATA HARD drive.
    The SATA controller must handle the tough without major problems.

    It is important that you use a HARD SATA 2.5 ". The size and speed of the HARD drive should not affect compatibility.

    See you soon

  • Satellite A100 - 153 (PSAA9E) - how to update display drivers?

    Hello!
    I need a current display for my ATI Radeon Mobility X 1600 driver in my laptop Toshiba Satellite A100-153 PSAA9E.

    I can not install the Catalyst Control Center (and therefore the latest driver). It says to me "this driver is not compatible with your system. Contact the manufacturer.
    In the magnificent... download section are the only drivers of 2006 for my X 1600. Anyone know how I can install current drivers? Is it possible to avoid the 'blocking of Toshiba' for display drivers?

    Thanks in advance

    Hey Buddy!

    The display on the original ATI site driver is not designed for graphics cards for laptop and so that you can install t. In addition he doesn t have an overheating protection and therefore can damage your graphics card! It s on your own risk!
    If you want the ATI driver, you must use Mobility Modder. Then you can install it, but don t forget s about your risks and perils and you will lose the warranty.

    The drivers from the Web from Toshiba site definitely work for your laptop then why you want to install a different driver?

    Good luck!

  • Satellite C660 - no Internet connection after updating BIOS

    I am a novice user and have a Satellite C660 under warranty that I don't use for surfing the net and Ebay so I hope I can explain my problem!

    Toshiba bulletin board said that the need to update BIOS, so I followed the instructions but since then I have no internet connection, and cannot restore the connection that I lost all help Toshiba Bulletin Board today lost and none of the programs to sort the problems work - e.g.set assistants etc. I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?

    Can someone tell me if it's a failure caused by the BIOS update or I would return laptop to John Lewis for repair? Thank you very much for reading this

    Hey Buddy,

    The default settings in the BIOS load after update? If this is not the case, go into the BIOS and load the default settings. You can enter the BIOS if you press F2 before Windows start and then press the F9 key to load defaults. Then save & exit the BIOS Setup.

    You can access the Internet now?
    You try to access the Internet with LAN or WLAN connection?

    Also check device manager if all devices are recognized correctly.

    > I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?
    You can create the Toshiba Recovery disk every time. Just launch the pre-installed Toshiba Recovery Media Creator and follow the instructions on the screen. You need just a few blank DVDs to create the discs. Disks contain a factory image of settings which can be restored each time and how many times you want to so with these disks, you are on the safe side ;)

  • Satellite A100-237: unknown device after installing Vista

    Hi all

    Just installed vista on my A100-237... After doing the upgrade of the BIOS and the installation of the "unknown device" Value Pack, with the location "on system compatible ACPI Microsoft" appeared in my device manager, any ideas on how to address this issue?

    Thanks in advance!

    Hello

    Could you please check if you can see the 'Batteries' entry under ' computer in Device Manager?
    As far as I know that the entrance of batteries should have a "Microsoft SMART Battery" & "Microsoft SMART Battery subsystem.

    If there is an unknown device, this might have something to do with Microsoft ACPI Compliant Embedded Controller.
    In this case it seems that you need a driver for MS SMART SMART Battery & MS battery subsystem.

    pleasae also check this thread;
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=14575

  • Satellite A60: Problem of memory after update Bios V.1.9

    Hi all

    I've just updated my bios to version 1.9 last week. Previously, I've upgraded my RAM from 512 MB to 1.5 GB (P4 2.8 GHz., 40 GB HARD drive) and my phone worked perfectly with the old Bios and RAM. After the Bios Update to the new version, 1.9, my laptop does not accept the module of RAM upgrade, windows xp still shows the blue screen, and then restart.

    After upgrading RAM off, my laptop works again. I tried several ways to solve this problem as take the battery, then reinsert the RAM or even formatted my HARD drive and installed a new Windows XP, but it didn't work. So what can I do to make my laptop to accept the upgrade of RAM? How to solve this problem? For this reason I now intend to buy a new laptop, if the problem can not be solved since I simulate a program on this laptop, so it requires a lot of memory.

    Thank you very much in advance for your answer.

    [Edited by: admin]

    Hello

    I put t really know what is the problem with the new update of the BIOS. In my opinion, you should contact the after-sales Service of Toshiba partner in your country and explain to them the situation. If your new module memory is compatible with the unit you should tell you want to have the old version of the BIOS. As much I know as technicians for this.

    If they see that there is a problem with the BIOS update, I'm sure they will for free.

    Good luck!

  • Satellite A100 does not start after the BIOS update

    Hello

    I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

    At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

    _________________________
    Genuine Intel CPU
    No TPM or TPM has problem
    1015 M system RAM passed

    Press to enter in SETUP
    _________________________

    Pressing F2 just clears the last message in line and then no change is found.

    The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

    I found similar messages around the forum without convincing answer.

    Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

    Hello

    Please don t blame someone for you mistakes ;)
    As far as I know that only a few sets of laptops come with TPM.
    If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

    Looks like you used a bad BIOS or bad BIOS update procedure.

    The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
    You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

    > Is it possible to fix this without sending
    Don t think so, and therefore, you will need to contact the Asp help!

    Good luck

  • Satellite L350D - crash after update BIOS?

    Hey all.

    Put windows XP on my Satellite L350D, worked well, has all the drivers etc. and works perfectly. Returned on the toshiba site and saw there is an update of the BIOS for it, then downloaded and says to install. To halfway through she turned off the laptop (thin power supply and had a full battery, so must have been updating).

    Now it will not boot up what so ever. The power light turns on but nothing else works.

    Im guessing that he wiped or corrupted BIOS, is there any fix for this, I can refer to toshiba or am I out of luck?

    Hello

    The failure of the Bios is one of the most painful problem in this forum. Too many discussions on the failure of the bios posted and typical response is to contact the ASP. Read this, may be useful for you

    http://www.theeldergeek.com/forum/index.php?showtopic=21209

  • Satellite C50B freezes at startup after update BIOS to 5.10

    Hello
    I updated the BIOS of my Satellite C50 - B - 14 d (PSCMLE) to 5.10 (a final release early sept. 2015).
    The update succeeded, and the laptop runs as long as I do not install the drivers for the card WiFi (Atheros AR9485).
    If I try to install the driver (it does not matter which, those of the Toshiba website or those of the manufacturer, of), the laptop crashes before the end of the installer.
    Installing drivers from Device Manager makes the laptop freeze on when Windows starts (I tried 7, 8.1, and 10).
    Completely on the Windows logo screen it freezes, and I have to turn off it.

    In addition, the wired network adapter is not detected (it does not appear in Device Manager).
    The same question is described here (http://www.eightforums.com/general-s...ses-start.html), but no solution.

    Any suggestion? The BIOS may be downgraded? The BIOS update utility does not Flash an older version.

    Thank you!

    Hi indutry,

    I also have exactly the same problem since updating my BIOS to 5.10 with my Toshiba C50 - B - 14 d PSC MLE

    I have to start windows in safe mode without network to disable the Atheros AR9485 before restarting again in normal mode.
    I now have to use an external WiFi adapter as my LAN port is now also lack!

    Upset that the BIOS update has broken all my embedded network on the laptop.

    I tried to update the Atheros drivers to the latest version, but as soon as the device is turned on again the system crashes and we're back to square one.

    There is no solution that I can find other than turning off the unit and live without built in WiFi + LAN.

    I hope Toshiba can be remedied with a new BIOS update?

  • Satellite A300 - pad touch dead after update BIOS 2.20

    Hello

    exact model is Satellite A300 PSAGCA-06M01N under Win XP.

    I had a problem with the webcam, and I read in the forum that it can be solved by a BIOS update. so, I advanced and downloaded the latest version of the BIOS on the site of toshiba, especially for my laptop model. It went quite well with no error.

    However when the computer restarts after that the BIOS updated my touchpad no longer works.
    I went to Device Manager and could still see the Synaptics touchpad device and it says "this device is functioning correctly. but its completely dead and will not respond with the 2 keys. before I updated the BIOS I never had any problems with it.

    I tried FN + F9, nothing helps. plugged in a USB mouse and it works without any problem. In fact, when I plugged in the mouse the synaptics software says "Deactivation of the key because of the external pointing device" for the device driver for the touchpad works.

    If I remove the mouse, it will say the touchpad is restored, but it still doesn't work. restarted several times and still the same problem. went into BIOS and chose "default" not still a no go.

    Can someone offer any advice or ideas please?
    I really need the touchpad for the way I use the laptop...

    Hello

    In many cases, the touchpad (pointing device) can be enabled and disabled in the BIOS.
    I think you should check if this option is available in BIOS and if so, check whether it should be enabled.

  • Satellite P500 - screen remains blank after updating BIOS 2.90

    I installed the new WOOD update through the station of service and after restart, the screen remains blank (out of service)?

    Any suggestions?

    Hello

    And on the external monitor you see a photo or not?

    In my opinion, something goes wrong during the update of the BIOS, and so the entire computer doesn t start anymore. All updates are pre-tested by Toshiba, so I doubt that only the screen isn't working anymore.

    You should try to remove the battery and unplug the AC adapter for an hour. Then install the battery and plug in the AC adapter. Make sure the battery is fully charged and then try to start your laptop.

    It's working now?

  • Re: Satellite A300 won't start after updating BIOS

    Today I was installing recommended THAT BIOS update 1.70 to 1.90. During installation, the mouse cursor disappeared and has no reaction to the keys on the keyboard. But there was a message DO NOT TURN OFF COMPUTER. So I waited for long (an hour?), but the update progress bar was always in the same place - as my computers are suspended.

    After a long time waiting without any response, I decided to reset the computer. Only way to do pressed turn on button for a few seconds.

    But after that turn it on again there is nothing visible on the screen, only the reaction of the computer is that bright development under tension is turned on and hard drive will blink every two seconds. What should do? Please help me! I have very important data on the hard drive at this moment! Can I reset the BIOS? I tried to yutm on the computer after you press ESC and F2 key, but no effect. I put the CD with the operating system, but no effect.

    Its possible that the BIOS chip is faulty, causing the update to the BIOS to fall down during the writing process.

    If you have tried reinstalling the RAM and removing the power for an hour, it is not great thing else you can do except send it to an ASP for warranty repair.

  • Satellite P300 cannot connect WiFi after update BIOS

    Hello

    After using the original BIOS updated to programm my P300 - 18M can not find wireless networks.

    I've updated with file BIOS on 2008-09-22 without any problem. The strange thing is: using the network wireless switch
    in front of the P300, it activates the Bluetooth on or off instead of the wireless network card. The wireless card is now is still running, but can't
    find any network.

    Another labtop sees several wireless networks, as well as the P300 did before upgrading the BIOS.

    Can someone give me some advice or help me with an older version of BIOS for Windows XP?

    Thnx!

    John

    Hello

    Very strange problem, but maybe it can be solved very easily
    You should try to simply update the WLan driver.
    In addition, you should access the BIOS and it should define the default settings.

    Check it out!

Maybe you are looking for

  • HP Simple pass does not properly.

    I just bought a HP Envy 17 TS last Friday. And the finger print scanner does not work properly. On the basis of the recommendations of the Forum of Microsoft, I deleted and updated drivers for both the pass Simple biometric and HP. Here's the situati

  • My experience using MS Synctoy on Satellite L350

    It is using the excellent and free MS Synctoy to synchronize the laptop and desktop computers all works beautifully on WiFi, but there are one or two oddities to know. I'm just thrilled to have this machine works again. And what a beautiful machine.

  • How can I configure the variables shared between executables created in sepparate projects

    Hello I have several projects sepparate with their own respective executable files and I would like to be able to these executables to all share the same variable (one program control the value of the variable, while others read her). I got this conf

  • Where slot - VI nisync?

    Hello I'm using Labview 8.6 on a PXI-1045 chassis, a synchronization PXI-6653 module, and a PXI-6552 HSDIO module. I want to use the CLOCK out of the 6553, but I can't find the Subvi PXI - 6553 NISYNC. Where are the Subvi NISYNC? I did a search for O

  • Can not put Windows Media says Server unavailable player security?

    Can not put Windows Media says Server unavailable player security?