Satellite A100 - 847 PSAA9E - 4 GB of ram, but it reads only 3 GB Win 64 bit

Similar Questions

• Satellite A100-847 does support 667 MHz RAM

  The A100-PSAA9 (A100-847) supports the 667 MHz RAM? The FSB is 667 MHz, but the laptop comes with 533 MHz RAM and everywhere that I looked for upgrades of RAM I've seen 533 MHz for this model.

  memory Finder: http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=25716&ft=m&st=3

  Hello

  It should be able to use the Ram 667 MHz module, but the difference between the 533 MHz and 667 MHz is not noticeable.
  I think the 533 MHz module is great and you are on the good side, if you use the modules to recommend Toshiba.

• Satellite L50D-C-18J - two modules of RAM but single track only

  Hi all

  A few days ago I got the Toshiba Satellite L50D-C-18J with A10 - 8700P AMD processor.

  Factory 1 with 8 GB (DDR3L 1600 MHz) memory module are installed. According to various tools (AIDA64, HWInfo64, CPU - Z), the memory will operate at 668 MHz, that is to say 1333 MHz mode.

  The free memory slot I have with another 8 GB DDR3L held at 1600 MHz (with the same memory timings, but other manufacturers). The Bank will continue to operate only in single channel mode and not in dual channel mode. The A10 CPU should support.

  I have installed the latest version of the BIOS.

  We have an idea of how I have the dual-channel mode and can set the frequency of the memory? In the BIOS, there is unfortunately almost no parameter or someone has the same laptop model and with it dual-channel mode is running?

  Thanks and greetings

  Mario

  Hello. Another manufacturer is not a problem.
  You should check the following:
  (1) make sure that the two RAM modules operating at 1.35v. Search the Internet, what should be the supply voltage of the RAM you have installed. If this does not work at 1.35v then that's the problem.
  (2) whether these RAM modules supports ECC. If one of your RAM supports ECC and the other is not, that's the problem.

• Satellite A100-847 - upgrade advice

  Hello

  I use the Satellite A100 - 847 (PSAA9E) for almost two years. 2 years warranty be over within a month, so I guees this is good time for an upgrade. I could use more RAM and a faster HARD drive (for purposes of CAD especially when I'm on the track) so I would like to know more about it.

  * What I already found out which is my laptop: *.
  (if I'm wrong with something to say please)

  1) ... May take 2 DDR2-DIMM modules; 4 GB max; which means 2x2gb. I have already 2X512GB, and it is not enough.
  -The question is what DDR2 memory! The FSB is running on 667 MHz, so I guess I should buy PC-5300/667 or even 6400/800?
  -What is the best memory for my laptop? Who gets very hot! What model is pretty cool?

  2) ... At a Hitachi Travelstar 5 K 100, 2.5 ", 5400 RPM, 8 MB, 100 GB SATA cache. The capacity is enough for me, but it's far too slow. So I guess I should to a 7200 RPM 16 MB disk cache.
  -The question here is my laptop support SATA2 or is - this just SATA1? What shlould buy?
  -My laptop does support disk 7200 RPM?
  -My laptop overheating with this drive?

  3) ... Could have a more efficient cooling system. Is there a solution to this?

  Thank you in advance,
  adambar

  Hello

  Googling autour I ve found track information:

  The computer has two SO DIMM slot comes standard with the DDRII 4200 module. He
  supports PC2-4200 and use SO DIMM (DDRII SDRAM) leads to 1.8 V, accepting
  BTO/CTO for your memory needs. It can integrate up to 4 GB of hand
  memory.
  By using the following formats of memory modules:
  256 MB (16 M × 16 × 8 P) / 533/667 MHZ
  512 MB (32 M × 16 × 8 P) / 533/667 MHZ
  1024 MB (64Mx16x8P) / 533/667 MHZ

  If you want to use the maximum RAM, you must use two 2 GB. Toshiba recommends the use
  2 x 2 GB RAM DDR2 PA3513U-1M2G. An alternative to this RAM module are modules memory high quality Kingston .

  On HARD drive, I can say follow:
  HARD drive interface compliant to Serial ATA (for 40/60/80/100/120 GB).
  The computer can accommodate a HARD drive of 2.5 inches with all the following storage capabilities:
  40 GB SATA (9.5 mm thick) (5 400 rpm)
  60 GB SATA (9.5 mm thick) (5 400 tr/min/7200 RPM)
  80 GB SATA (9.5 mm thick) (5 400 tr/min/7200 RPM)
  100 GB SATA (9.5 mm thick) (5 400 tr/min/7200 RPM)
  120 GB (5400 RPM) SATA (9.5 mm thick)

  As far as I know that SATA2 is backward compatible and theoretically, you can use it, but I'm not sure about this. If I were you, I would by SATA1 HDD.
  As you can see, Toshiba has tested 7200 RPM hard drives with this model of laptop, and you can use it also.
  Maybe not overheating, but I can imagine that the plastic cover will be hotter than before. Make sure just the laptop is placed correctly and that there is nothing blocking the cooling fan.

  More efficient cooling system? I put t know what you mean exactly end-to-end you can try something like this.

• Satellite A100-847: how to set 1680 x 1050 on external screen?

  Hello

  I have a problem.

  My laptop Satellite A100 - 847 PSA9E 2 GB of RAM, nvidia 7600 Go 256 MB.
  I also have external 22' SyncMaster 226BW WSXGA 1680 x 1050

  The problem is that with the original driver (84.68) I can not set the resolution to 1680 x 1050, but I know that the video card supports. I tried the www.laptopvideo2go.com drivers but still those who do not work perfectly.

  Can someone tell me what to do?
  Perhaps the BIOS update can fix this problem? Or maybe another solution?

  Please help :(

  According to the specification of the graphics card (in combination with the preinstalled display driver) doesn't support resolution 1680 x 1050. Supported resolution is 1600 x 1200.

  If yiou can't find solution as a result of this web page, I really don't know what you can do. This page a little better. There must be detailed how change resolution modes.

• Satellite A100 - 712 (PSAA9E) - No. TPM or TPM has problem

  Hi all!

  Once again, the same problem with the update of the BIOS...

  Quotting there
  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=121750#121750

  "I decided to update the BIOS on my Toshiba laptop Satellite A100 - 712 PSAA9E to the latest version available (6.00).

  The installation is completed normally (went through all the steps, wrote to all 21 blocks) without any error, but after the reboot, I noticed that it is now displayed at the Toshiba logo screen.

  The blue progress bar moves twice but got caught then about 1/3 of the way through.
  To see how bad the damage was, I Press esc at the beginning of the POST and saw that it gives me the right Version of the BIOS (6.00).

  He also told me that "no TPM or TPM has problem" and "2039 M RAM Passed system."
  It then displays the message "Press to enter SETUP" (which makes the message disappears, but otherwise doesn't do anything.

  If I press F2 during the Toshiba logo screen, it replaces the bottom with "Please wait" message and nothing happens"

  Sollution "go to ASP" in the footsteps of sollution.

  Is there someone who can explain how to use the crisis to Phoenix (PCD) disk?
  I did floppy of PCD, replaced BIOS. WPH with my version of BIOS.

  After pressing WIN + F and on floppy power begins to work and beeps is my note. After 1 minute - all freez... Same thing with bios.bak - old version of my BIOS made after the beginning of Winphlash.exe...

  Wayting for the answer!

  Hello

  I posted this already in another view about a similar BIOS problem.

  To me, it seems that something was wrong during the process of updating the BIOS, and if you're lucky, the flashing of the ROM BIOS might help you.

  As far as I know that you would need a BIOS version of special rescue and the drive to reflash the module ROM that you do not and therefore, you will need to contact the ASP in your country for assistance.

  This isn't a real solution that you expect, but it s an advice how to get a solution
  This is why I would recommend contacting the ASP in your country for the control of the laptop

  Good luck buddy

• Satellite A100-847 - replacing a WLan card

  Hello

  I have Toshiba Satellite A100-847. I would change as WIFI card for new with "n" standard.
  I found some tutorials how to proceed, but it was for Toshiba A105, very similar to my only.

  I opened the bottom cover where is memory and modem, but I couldn't see all the PCI ports.
  Is it possible to do?
  Does work through mini-PCI or is integrated on the motherboard?

  Hello

  The A100 PSAA9E supports a minPCI WLan card that supports the IEEE 802 standard. 11a / g WLan standards.
  I m not 100% sure if it would be possible to upgrade the WiFi network with a WLan card 802.11 minPCI n because the two antenna cables.
  You should first clarify if the antenna is compatible with the 802.11 standard new * WLan N standard *.

  The minPCI wireless network card must be hidden under the keyboard. So you'd have to remove the keyboard first to get access to the wireless network card.
  The wireless network card is also connected to two antenna cables. The cables must be removed carefully using a pair of tweezers. Then spread plugs securing the wireless LAN card until the card appears.

  Usually it of not difficult to replace this WLan card but if you have no experience I wouldn t recommend doing this.
  This replacement must be done by a qualified technician!
  In addition you guarantee the validity could be cancelled after these updates.

• Need drivers for Vista 64 bit - Satellite A100-847

  Hello.

  I'll install Vista x 64.
  First of all, I wanted to download the necessary drivers.
  When I use toshiba Web site there is no x 64 drivers for my model A100-847.
  Where can I find them? The drivers are included in Vista?

  Hello

  Satellite A100-847 seems to belong to the PSAA9E series!
  I checked the page European driver of Toshiba and unfortunately; 64-bit Vista drivers are not available for this series of laptop.

  However, there is perhaps a chance to get 64-bit drivers, I know that some series of laptops are equipped with the same features. This is why some unique drivers should run on the series of portable different too.

  You should check some other series where 64-bit drivers are available and try to install it maybe you're lucky.

• Satellite A100-847 battery led blinks 11 times, absence of motherboard?

  Hello

  14 months (only 12 months warranty), I have a Satellite A100-847 was a laptop perfect, but 2 weeks ago the ac-adaptar falls down and since then that if I push the power button the battery orange led blinks 11 times with the same length, but nothing happens.

  ASP did not now what this flashing means but think I have a motherboard problem.
  Now I found on ebay a Satellite A100-153 and my question is, is this the same motherboard, because it's also 945 PM.
  (Sorry for my bad English)

  [Satellite A100-847: http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/SUPPORTSECTION/discontinuedProductPage.do?PRODUCT_ID=120570&DISC _ MODEL = 1 & service = EU]

  [Satellite A100-153 | http://de.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/productPage.do?service=DE&PRODUCT_ID=112714&PRODUC T_ID = 112714 & toshibaShop = false]

  THX.

  It seems that two laptop computers support the same motherboard as the Satellite A100-847 and Satellite A100-153 belong to the same series of PSAA9E.
  This series uses the same drivers and the same BIOS so I think that the mobo must also be the same.

  PS; I think that it is a motherboard problem too. Such a code is displayed only if a hardware failure has been detected on the motherboard.

  Best regards

• Downloads of drivers for Satellite A100 - 230 (PSAA9)

  Hello, I need all the drivers required for Satellite A100-230 (PSAA9) for Windows XP, I just installed a fresh copy of XP and I have Dona´t have the CD that came with the computer, as well as I need to download?

  Why you n t take a glance o page pilot European Toshiba!

  Did you check this page from pilot:

  http://EU.computers.Toshiba-Europe.com-> support download &-> download drivers

  Perhaps you didn't look in the right area?

• Satellite A100 - 771 PSAA9E: ID ERR NOTINSTALLTVALZ MESSAGE appears

  Hallo,

  I've updated my system from xp to vista. The type of my computer laptop Satellite A100 - 771-PSAA9E ist.
  and when I install the update program, which either download the form from the website, to get out this message

  'ID_ERR_NOTINSTALLTVALZ_MESSAGE '.

  I know donnot, where is the last problem. (I downloaded the program just for my laptop)

  Can someone help me?

  Thank you very much.

  Hello

  Advanced search is a very nice feature. You know. I have used and found this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=20471&MessageID=75256

  You will find the same deal and the solution!

  Seems that the BIOS update is a key.
  Good day

• Is PA3512U-1M1G 1 GB memory PC2 DDR2 667 MHz compatible with Satellite A100-847

  Is PA3512U - 1M1G 1 GB memory PC2 DDR2 (667 MHz), RoHS compliance version compatible with TOSHIBA SATELLITE A100-847?

  Hello

  Please visit the page European Toshiba under http://eu.computers.toshiba-europe.com > Products > Options & accessories

  It has listed all the compatible memory modules for your laptop model Satellite A100.

  By the way: as far as I know all the compatible memory modules are 533 MHz module.

• Satellite A100-912 (PSAA9E) a device is missing after installing Vista

  Dear,

  I recently received a Satellite A100 - 912 (PSAA9E). Windows XP Home was preinstalled operating system. But when I installed Vista Ultimate, the Device Manager shows that a device is missing pilot. Its properties show that it is located on PCI, device 6 7 Bus and function 3.

  I downloaded the drivers all listed for the toshiba site system. So, can someone tell me what device it is and where I can find the driver for it? All devices such as the display, sound, modem, lan/wlan, player card, fingerprint reader, buttons of media multi burner Super multi and touch to touch work well.

  Hey Buddy,

  I Don t really know what device it is, but you can for example try a linux live cd. The live cd lists you start a list of pci devices so you can find that materials are in your machine.

  Alternatively, you can perform a search in google for 'list of pci Vista' and you might find some pci list of tools that can help you get information about unknown material thjat.

  Welcome them

• What is the recovery CD contain - Satellite A100-847

  Hello guys

  I had a few questions on the recovery CD:

  1. what the recovery CD contain? and the other CD, which is called the media something?

  2 - has Windows inside? So can I format my PC to use it? And where can I find the product key (windows key)

  3. what happens if I wanted to use the CD without formatting? etc., install the software?

  Sorry to ask too but my laptop started to bother me. Just FYI, my laptop is satellite A100-847

  Hello

  I'll try to answer your question.

  1 recovery media contains recovery image. Recovery image is a kind of package that contains the operating system, all necessary drivers, Toshiba tools and utilities and some other software like WinDVD or Norton antivir application. Media, that something is not known to me. Perhaps the exact description can help.

  2 Yes there the Windows operating system. Yes, you can format your laptop to use it. You don't need a product key. Just install it.

  3 I don't know what you mean. The fact is that HARD drive will be formatted before you start the installation of recovery. Make sure that all your important data are saved on an external device.

  Good bye

• Satellite A100-847 - Virtual sound driver for Windows 7?

  Hi guys,.

  Is there an available virtual driver sound for win7?

  I use Satellite A100-847 and impossible to find some drivers.

  Thanks for your help.

  Hey,.

  What is a virtual sound driver?
  I know only driver sound but where is the difference with the virtual audio drivers?

  In any case, you should check the Web from Toshiba site if you can find the drivers for Satellite A100-847 and Windows 7:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Check this box!