Satellite A100 does not start after the wrong Bios Update

Similar Questions

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Satelite P300 does not start after the failed Bios Update

  Hello world

  I tried to update the bios of a P300 to this:
  18/03/10
  Update the BIOS
  Toshiba Windows 7-32 Bit 4.20 - WIN32 World Wide
  That I downloaded here: http://uk.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=UK after entering my laptops specs.

  The process flash hanged during the update and the laptop became screen starts, blank when turning on and nothing else...
  I tried to use the Phoenix of emergency crisis, created a diskette with the file Bios image that I downloaded but nothing succeeded.

  Access to the floppy drive USB floppy when you enter the recovery mode, I hear the beeps that indicate that a process is carried out, but when everything stops and restart... the problem remains.

  -Does anyone have a clue what to do next?
  -The warranty is void after a bios update attempt?

  Thank you for yor time.

  > - Someone at - it an idea what to do next?
  Well in this case, you will need to contact a local ASP (Toshiba authorized Service Provider).
  Guys could clean CMOS and flash the BIOS ROM module with a BIOS disk special crisis

  You will find here all the FSA all over the world:
  http://EU.computers.Toshiba-Europe.com-> support download &-> locate an authorized Service partner

• Satellite M200 does not start after the RAM 4 GB upgrade

  Hello

  I recently updated my RAM just to speed things up a bit as RAM is so cheap these days.
  I have a MEAC M200 T2130 Vista with 1 GB sticks (2 * 512).

  The new sticks are 2 * 2 GB Dane - elec DDR2 pc2-5300, when I put the two and restarted the hard drive light came briefly and then it is just options BIOS of Idol, no POST.

  I tried to use a single stick of 512 MB with two new sticks and they both work in a 2.5 GB configuration just not together that also this only works when the stick of 512 is in internal housing and not vice versa.

  So if someone has had a similar prob or can give me some advice that would be great, I'm not sure if the motherboard can support 4 GB?
  Thank you, Dave.

  Hello

  There are two possibilities why your M200 doesn't not start after upgrading RAM.
  First the RAM installed may be not compatible or could be faulty or the computer laptop doesn't support 4 GB of RAM.

  I put t know what M200 do you have exactly, but you can check the installed chipset and could check on the Intel page if this chipset would support 4 GB of RAM.

  Welcome them

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• Aspire One D257-13478 does not start after the system BIOS flash.

  I gave my child a D257 - 13478 new ASPIREONE.

  It came with Windows7 starter - was very slow, crippled and crashed a lot.

  After a while, I have re-formatted the HARD drive to remove Windows-resources-pork-7, and I installed Windows XP Professional (SP3).

  After which, the netbook has been much faster, and I could navigate with 5 windows open browser (FireFox) and NEVER receive (not RESPONDING), as I was always getting with Windoze 7. He's been good for 5 months.

  Anyway, it worked fine except that I could not find driver XP for [CODE 10] Broadcom wireless card,.

  so we were not using WiFi.

  Today I read the suggestion to update my BIOS to correct [CODE 10 number}. I went to acer link and downloaded the BIOS of the Organizer, RAN the EXE and the netbook went to restart.

  When the ACER logo appears, a blue screen flashed QUICK, and the netbook RESTARTS again.

  Asking me to start Windows normally just repeat what's happening above

  When I choose Safe Mode... drivers will charge up to Mup.sys and then the system just REBOOTS.

  When I try the last good Configuration known, same thing.

  Enter the system (F2) shows, Version of the system Bios configuration utility: v1.15

  It used to be all about v1.10.

  .................................................

  Then. What is my next step?

  Will be my HD reformatting and reinstall WIndowsXP DIFFICULTY this problem?

  or

  How can I RESET my Bios to v1.10 (when everything was fine).

  No software to use on a USB key to solve this problem? (because theres no CD don't drive of course)

  Thanks in advance.

  Hi MOne

  The flash will have changed the BIOS settings, so go in the BIOS settings and verify that the setting of the HARD drive is in AHCI mode. If it still does not start XP, then it is worth trying to format & reinstall Windows from scratch.

• Windows 7 does not start after the installation of updates - sounds familiar!

  Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

  Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

  Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

  Here's the resolution...

  I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

  My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

  Now my system is up to date with all windows updates and I'm able to restart without any problems!

  Close this message.

• Satellite L350 - does not start after the BIOS update

  Hello

  I recently (yesterday) downloaded the latest version of bios update dated dated 25/02/10 2: 20 - WIN, after download and does run the software from the laptop immediately stopped working and stop. I am now no longer able to boot up the laptop at all, all I get is the power light on and the hard disk light flashes, I hear the spinning CD/DVD drive, but what is not screen anything, I don't think this is the start.

  Is there a way to fix this without taking it to a store/engineer, BIOS recovery?

  The laptop is a Satellite L350, I opened the laptop to try to reset the CMOS by removing the card mother battery (not sure if it would have helped), but as much as I know it doesn't have an or I'm not.

  Any help would be greatly appreciated.

  Thank you

  Andy

  Hi Andy,.

  Hmm... If the BIOS update failed, you can't do anything because only an authorized service provider has professional diagnostic and recovery tools to redo an update.

  So in my opinion, you must contact a service provider authorized in your country. Get in touch with the guy and ask for help. They will tell you what to do now.

  Here is their list:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  Good luck! :)

• Satellite A40-231 does not start after the incorrect firmware update

  Hello
  I have a toshiba satellite a40 - 231.it unbootable because I flashed it's drive(sdr-6112) dvd - rw with the wrong firmware and I also made a mistake in making a non bootable back active partition, try to Flash the correct firmware. So my question is: can I boot from the usb flash drive? I think it's the only option I have left, if not network startup.

  Thanks in advance!

  Hello

  As far as I know it of not possible to start other devices from the USB FDD / HDD / CD-ROM / LAN

  You can boot from network, but if you want to install the OS via the LAN you will need a RIS server. But it's not easy to do without any additional experience. So I think that this option isn't for you.

  It seems that the drive is dead or is malfunctioning and that is why the best idea is to replace the device's drive. I know, it's hard to hear that, but I don't see any other solution

• Satellite A30 - does not start after the RAM to level

  Hello

  I recently installed a crucial for memory
  my laptop, which is a Toshiba Satellite A30. However, when I try and
  restart the laptop, he tries to restart the fan turns on then turns off with a beep sound and this is not
  even to get to the Toshiba start screen.

  The memory I installed is 1 GB, 200-pin SO-DIMM, 128 X 64, DDR 333, CL2.5, part number CT12864X335.

  "Memory module PC2700 DDR 1 GB, 200-pin SODIMM

  CT12864X335
  
  
  * Size of the module: * 1 GB
  * Package: * 200-pin SODIMM
  * Function: * DDR PC2700
  ' * Features: * DDR PC2700 • CL = 2.5 • unbuffered • NON-ECC DDR333 2.5V • • • 128Meg x 64 •.

  I have
  took out and put back the old memory and the laptop boots
  normally and is OK, I even tried to put the memory in different
  slot machines, but it still has the same problem.

  This suggests that memory is faulty, as bought crucial memory must be compatible with my laptop?

  Thanks for your time,

  You have this problem if you use modules or only the new module?

  If you only use the new module, the case is clear. The new module is defective or is not compatible with the laptop.
  I think you should get back on the computer dealer and request a new. Maybe you can get a Kingston module because I have only good experience with this production.

  If you use both modules, they are not compatible. You should only use the modules with the same specifications.

• Satellite L30 does not start after the BIOS update

  Hello

  I upgraded my BIOS Satellite L30 and now the laptop will not boot. When I turn on the fan starts and that's it. I think I have updated the book with the bad BIOS... The laptop is only 1 day old... Is it possible to reset the machine to the default BIOS.

  Help, please...

  Hi Scott,.

  Unfortunately there is no easy way for you to go to your BIOS to its previous level. You need to entrust your laptop to a Service approved partner who has the necessary equipment to Flash the BIOS to the previous level.

  Kind regards

• Satellite L855 does not start after the BIOS update

  I downloaded the BIOS update and followed the instructions there during the installation, but on reboot (including the requested configuration), I get a blank screen. Intermittently, the CPU fan starts and stops. I think that the BIOS update failed, how to solve this problem?

  Thank you
  Neil.

  Hello, Neil

  In General when the BIOS is screwed up you need professional help and you should contact the nearest Toshiba service provider and ask for help.

  See also this thread. Perhaps this methid can help you too.

• Satellite L40 - 14 H - do not start after the successful BIOS update

  Hello

  I have Satellite L40 - 14 H which was working fine until I thought to an update of the BIOS will not hurt. Seems I was wrong.

  I downloaded the update to the BIOS, it unzipped in a folder and started the action.

  After a few seconds was asked to wait, and then after few more firm.

  After the reboot, I pressed F2 to enter the BIOS and check that it is version everything was fine, version 2.0 so was I left once the parameters.

  After that, nothing happened.

  I almost tried everything without success. Removed the power and battery power, put their back, but still no start. Just the light of the HARD drive lights up for a few seconds and the cd turns a bit, but after that nothing happens at all and completely the screen is black.

  I don't know anything else to try.

  Please let me know what that can do to restore its functionality without taking it to the service, I can't do it.
  I think that may not be cause of failure of the BIOS update I have seen it is the version and was right.
  Is it possible to reset the BIOS? I need to disassemble the laptop to do this?
  Let me know what to do, I have good experience in such things, but I can't understand this.

  Thanks in advance for any response.

  Kind regards
  Stefan

  Hello

  I agree with Akuma. It really isn't that you can do about it. BIOS problems are complex and cannot be set by the owner of the laptop. Believe me you need professional help with this.
  Contact the closest Toshiba ASP and explain the situation.

• computer does not start after the installation of updates

  Just click on the button "installs the update and the computer shuts down."  When the computer turns off automatically, I pushed the power button and now it is frozen the computer in start mode.  What should I do now?  Can I power off and try again (or which will mess up the configuration of the update that he just installed.

  Note: There are 21 updates installed last night without problem; then 1 update again (that set up correctly when I restarted this morning).  After a successful this morning launch, I noticed there was an another update to install, which is what made me at this point.

  Single computer at home (I use my work computer to submit this application).

  Wait awhile and see if, during the initialization of the problem to be solved or not. It is NOT a good idea to unplug the laptop.

  If this does not work, then try to press F8 and choose last known good configration, but you may need to reinstall the update again.