Satellite A135-S2356 won't boot after BIOS update

Similar Questions

• Notebook G71 won to boot after BIOS update on HP site

  I just updated the BIOS on my notebook G71... I downloaded the update from the HP site and it has been updated V20 to V23.

  After the update, the system became an automatic restart and now it does not move before the initial startup screen that shows HP and "ESC to return to the Start Menu" logo at the bottom. I tried the ESC key, but nothing past then is except that it says "esc... pause start." Nothing anyway. Now I can't reboot my system and it is dead. Help, please. Steve

  Unplug the power cord, remove the battery, hold the power button for a total of 30 seconds, connect AC only, see if it will load windows now.

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• Satellite L40 (PSL48E) - is not restart after BIOS update

  Hello

  My problem is that I have updated the BIOS and after that the machine does not restart. (Corrupt BIOS?)

  After that the BIOS updated (Satellite L40 PSL48E), reboot the machine and with the F2 key, I open the BIOS setup.
  I check the version of the BIOS (5.50) and complete the configuration of the BIOS. The machine must restart now...
  Not at all, the machine does not restart. No screen only the powerled lights.

  I can to fix it on my own as a BIOS reset?

  Thank you for the cooperation.

  It's strange because after that the updated BIOS update you can go into the BIOS.

  However, try to remove the battery and the AC adapter. Wait one hour and then put the battery back in and connect the AC adapter. Try again.

  If it doesn't work it is something wrong with the hardware or BIOS and must be checked by a technician for laptop.

• Re: Satellite X 200 - 20F - slow pace after BIOS update

  Hello!

  I have a Satellite X 200 - 20F bought about 4 years ago. I changed the bios 2.70 recently and I had a problem when I play games:
  The performance of the laptop suddenly decrease after a few minutes of play. For example, when I play Fable 3 + or + + Duke Nukem Forever + the framrate goes to 10-15 fps of 40-50 fps. I need to restart the game to correct this, but even that, the problem come back...

  I used version 1.40 BIOS and no problem.

  What should I do?
  You have one advise?

  Thanks in advance,
  Direct them best.

  Hi Crowzer,

  I m wondering that you did a BIOS update if you didn't have any problems before

  I can only imagine that a BIOS setting is different now. So I recommend to load the default settings in the BIOS, then save & exit.

  Try also to update your display driver. You can find the latest version on the official page of Toshiba also.

• Satellite A200 (PSAFCA) does not work after BIOS update triying

  Hello

  I was hoping if someone could help me pls.

  I have a Toshiba Satellite A200 (PSAFCA).
  Recently, I tried the bios update and while I flashed the bios I forgot to plug the laptop into the current and the battery was flat at half way through the flashing.

  Thus the laptop now won't post when I turn on and all I get is a white screen.
  I was wondering if someone could pls advise me on how I can get the old bios back or even a method of flashing it if I put the bios back in so I can at least get a message to display on the screen.

  Any help that you provide would be greatly appreciated as I am at a loss.

  Thanking you in advance

  muzzy001

  > while I flashed the bios I forgot to plug the laptop into the current and the battery flat at half way through the flashing.

  Well buddy, the cell must always be connected to the mains during the execution of an update of the BIOS! This is very important!
  Now it looks like the update of BIOS didn't t run and finish correctly and the ROM module seems to be flashed incorrectly.

  Unfortunately, there is no other solution to communicate with ASP guys and ask for help! They should be able to help you.

  But note; in the worst cases, the ROM module is unfortunate and the motherboard needs to be replaced.

  Good luck

• Satellite A100-TA7 hangs at POST after BIOS update

  Kind of tech swavy, I know that my chances are very low to solve this but this is.

  I decided to update the BIOS on my laptop Toshiba Satellite A100-TA7(PSAA8C-TA702C) to the latest version available (6.00).

  I did it because I've heard of people have better luck doing their job of FN keys on linux with the latest BIOS.
  The installation is completed normally (went through all the steps, wrote to all 21 blocks) without any error, but after the reboot, I noticed that it is now displayed at the Toshiba logo screen.

  The blue progress bar moves twice but got caught then about 1/3 of the way through.
  To see how bad the damage was, I Press esc at the beginning of the POST and saw that it gives me the right Version of the BIOS (6.00).

  He also told me that "no TPM or TPM has problem" and "2039 M RAM Passed system."
  It then displays the message "Press to enter SETUP" (which makes the message disappears, but otherwise doesn't do anything.

  If I press f2 during the Toshiba logo screen, it replaces the message at the bottom with "Please wait" and nothing happens even after an hour of waiting.
  (Which makes sense, because before the bar blue everything would load before entering the CMOS settings). The thing is that the BIOS is not really "freeze", it gets stuck just at a specific place (I know because I can press F2 even after an hour of waiting and the laptop meets it by displaying "Please Wait".)

  Someone at - it no more things I could try? Thank you

  PS. I tried clearing CMOS too. (Now the power button for 60 seconds without energy source<--- i'm="" not="" sure="" if="" this="" is="" how="" you="" do="" it="" on="" this="" laptop="" so="" any="" info="" would="" be="" nice).="" and="" i'm="" also="" 100%="" sure="" i="" chose="" the="" right="" bios="" update="" and="" followed="" every="" single="">

  Ola Amigo

  It of very long history and it does not sound good

  > I decided to update the BIOS on my laptop Toshiba Satellite A100-TA7 (PSAA8C-TA702C) to the latest version available (6.00).
  I wonder about your BIOS version that I know, that the laptop series is designed for the Canadian market. It s a Canadian series and the BIOS or drivers should be downloaded from the Canadian site of Toshiba!
  Bad BIOS could cause issues like this it describes your message above!

  > I did it because I've heard of people have better luck doing their job of FN keys on Linux with the latest BIOS.
  Keys FN Toshiba need driver Toshiba and it turns out that Toshiba driver pages don t offer the drivers for Linux distributions, so I put t believe in the story spread by any people.

  I don t want to write a long story, so I would cut this now;
  Is that something was happening during the BIOS update process.
  Either you have used a procedure to update the BIOS or wring wrong and so the laptop can not pass the MESSAGE

  You will need to contact the local ASP to solve this problem, maybe you're a lucky guy and the technician should Flash the ROM module but in the worst cases, your motherboard is damage and must be replaced. :(

  Good luck

• Portege M800 no boot after BIOS update

  Hello

  I encountered some problems with my netbook (Portege M800-10W) after the BIOS update.
  The update of the BIOS program appears failed. Then my Netbook automatically rebooted and now I can't start my PC more.
  All the LEDs will light up but the screen remains black and after a few minutes, the beep 3 times (1 long, 2 cm) netbook.

  How do I restore the BIOS to the previous version (or plant)?

  Thank you.

  Adrien

  null

  Hi Adrien

  I think that Akuma is right. Your laptop must be verified by the service of Toshiba s. Let check your laptop and I hope they will help you with this.

• Satellite L750 - Bluetooth does not work after BIOS update

  I am preparing some L750 notebooks for use and accept updates from the Toshiba, which included an upgrade of BIOS v1.70 for v2.00. He appears after this update occurs that Bluetooth no longer works, i.e. try to install Bluetooth Toshiba stack will fail as it is said that the Bluetooth radio is disabled and must be turned on for continue.

  As the L750 (model PSK1WA-0C300R) is not a hardware switch to enable or disable the Bluetooth/Wi-Fi, the only option available (Fn + F8) is unsuccessful. I ran a recovery of factory default installation and Bluetooth still does not - resumption of classes does not restore the BIOS to the previous version. I have 5 of the model and confirmed the update of the BIOS is the cause. Two laptops now have v2.00 and Bluetooth has been tested in the work before the update of the BIOS.

  If Bluetooth is not critical for the environment which I deploy these notebooks, it's an annoyance I want to solve. My questions are: has anyone encounter the same problem and managed to resolve it? Is there a BIOS v1.70 available for download to restore the functionality? Y at - it an update of the BIOS > V2.00 for solve the problem I have? Thank you.

  Hi JasonL750,

  Load default settings after updating the BIOS? Go into the BIOS, press the F9 key to load the default settings of the installation. Also, make sure that Bluetooth is enabled in the BIOS if there is such an option.

  In addition, it would be interesting to know what happens if you use the FN + F8 key combination. Don't you see that he has an option to turn on Bluetooth and if so what happens if you do this?

• Satellite M100 - no speakers sound thorugh after BIOS update

  Hi all

  I have satelite M100 PSMAAA-02006 with XP. I just updated the Bios on V3.0. Speakers do not work after update but the audio jack works so with headphones I can listen to but not through Laptop speakers and the keys to media on top of keyboard play, pause, stop, next, back, etc. homepage react too much.

  Someone knows the solution to this issue. Or is it possible to get the old BIOS? Although I not sure aboutt previous version.

  need quick help. Please answer as soon as possible.

  Thanks & best regards...

  Hi Julie,.

  I doubt that this was due the update of the BIOS. Is that what you have loaded default settings after updating the BIOS?
  Have you chosen the correct BIOS update?

  Normally you can hear the sound on the speakers laptop if you disconnect the headset. Make sure that the sound is not muted, you can do this with the FN + ESC key combination.

  About the multimedia keys, I would recommend reinstallation of Toshiba common Modules. You can find it on the Toshiba site.

• Satellite M100-165: screen dithering also after BIOS update

  I bought a Satellite M100-165 PSMA1E-2 days ago and I have the same problem as toshiba it described here:
  http://support.toshiba-tro.de/KB0/TSB6901K20002R01.htm

  I updated the bios to version 2.10 and the latest ATI drivers, but the promblem is still there.
  Is there anything I can do to solve this problem, because the dithering promblem is really annoying!

  P.S. The LCD Panel seems to be a SEC5643

  Hi guys

  If you have read the topic about this issue with the Satellite A100, you will see that many user were frustrated but right at the last update of the available BIOS. It cannot happen overnight and in my opinion, you must be patient and hope that the good BIOS update will be available shortly.

• Satellite Pro L100 does not work after BIOS update

  Okay, the computer is a Toshiba Satellite Pro L100 PSLA4. Problem occurred during an update of the BIOS on the official website of Toshiba. I downloaded the zip file, it extracts and activated the .exe file at the Interior.

  The window opened by the .exe is a program flashing BIOS, the .exe wrote at the same time a new BIOS file to a temporary folder.
  When he tried to use the program I got was an error saying it couldn't find the new BIOS to the entrance.

  I tried again only to get the same error. Then I left the laptop for several minutes and when I got home, I found a laptop no longer Virgin.
  On which I hear by an obvious lack of BIOS functions i.e. power LED does not change when the connection to disconnect it from the power outlet and the fact that I had to take out the battery to turn off the machine. When the power is turned on now it is check readers and restarts (no display, no beeps)

  What should I do?
  The first thing that comes to mind was to reset the BIOS.
  A problem, I can not find the RTC battery or a rider switch.

  Hi George

  I can't tell why it happened, but I can tell what happened.

  In my opinion, something went wrong during the process of updating the BIOS and the ROM modules was not writer properly.

  Simply says the BIOS update procedure has failed.
  In this case, you will need to contact the ASP in your country for a fix
  The technician must be able to rewrite the ROM module and updated the BIOS again.

  Good luck buddy

  See you soon

• T500 takes 15 minutes to boot after bios update

  symptoms:
  It takes about 10 or so minutes to reach the thinkpad press f1 to set up the screen, after that it gives me a screen that tells ME is initializing, it is after an update of the bios and later roll back bios. two updates to the bios give me the same result. functions of sleep also seems to not work, once im in my t500 windows works normally.

  what I did:
  In addition to rolling back the drivers Ive unplugged / replugged the cmos battery and off AMT. Ive also ensured that all my drivers are up to date.

  machine is a performer of 2081-cto on win7

  someone has an idea of what I can do? I still have a warranty but I would like to fix myself so I don't have the time.

  
  

• Cannot boot after BIOS update

  Hi, I recently bought a laptop Inspiron 5000 series, and because the touchpad control was just horrible I did a check for updates and upgrades. The update includes an update of the BIOS I plugged the laptop and ran the update. When it restarts, it failed. All I see is a boot failure:

  The family Realtek PCIe controller error. Media Test failure UNDI. No found boot device.

  I couldn't do a safe boot, but when I tried to get around the boot legacy and UEFI boot it will start.

  I am quite unhappy that a BIOS update (version 1.1.9 was the old version and 1.2.2 was new) caused this. The laptop is only 4 weeks old if I want to get this resolved.

  What should I do?

  You need not Mech system program.  This is what DellCares told me to do it on Twitter:

  Turn on the machine, key to tap F2 on startup Dell logo, it takes you to the BIOS screen. Go to the "Startup" tab, select "start list Options", change the option to "Legacy" to "UEFI".  Restart the machine, it should load correctly in Windows.

  -----

  I must point out that many others on twitter had already told me to try the same thing.  A person has explained why this has happened.  He said upgrading the BIOS changed the start to the legacy option when we UEFI.  Enter the BIOS and change this back solved the problem, so he's probably right.

• Pavilion dv6-7029wm, do not boot after BIOS update

  Hello

  Here are the details of my laptop and the problem.

  Product name: Pavilion dv6-7029wm

  OS: Windows 7

  Error: Fail to start. Caps Lock flashing in 1-1/2 dry once continuous, red wifi light on. Power light and the battery light on, no flicker.

  Pre-grant changes: updated to the latest BIOS updates as well as 3 other updates; security etc.

  I've tried remove the battery, unplug adapter, start-up. It still does not work.

  Its only for 5 months I've had this laptop. Please help me.

  Hello again Sowmya_Harsha.

  Unfortunately there is nothing more I can do.  However, I've increased your case.  You should be contacted by a specialist soon.  They normally have with customers using the feature of private message on the forums.  If you don't know how to use the private message function, take a look at this thread. I wish you a great weekend!