Satellite A200 - 14 d is unresponsive to the netsh command

Similar Questions

• Satellite A200-13O: need some answers on the upgrade of RAM

  Hi there everyone,

  I bought the Satellite A200-13O and I found in the forum Jayjay says:

  Bq. "the laptop can be upgraded up to 4 GB (2 x 2 GB). But the Windows operating system will not recognize the full 4 GB. He acknowledged only 3 GB due to the limitation of the 32 bit OS': 0

  Q1 - is saving 1 GB of RAM cause any problem, when is not used?

  Q2 - can spare 1 GB waiting in my book up is 32-bit upgrade to 64-bit?

  Q3-How can I upgrade CPU 32-bit to 64-bit?

  And just need to confirm a report of R2D2 on notice the guy with A200 - 14 d that have 'problem with RAM', which is similar to my confusion-

  Bq. "... The laptop was equipped 667 Mhz modules, but the FSB supports 533 Mhz max. That's why the modules run max with the speed of 533 Mhz (dual channel)... »

  Q4 - can I install 2 x 2 GB DDR2 667 MHz PC2 - 5300 SO - DIMM despite FSB run just 533 MHz?

  PS: could you recommend good antivirus, I am not satisfied with norton because it is really really really slow!

  Thank you all for the advice (!)

  Hello

  This article may be interesting for you
  http://APS2.toshiba-tro.de/KB0/TSB82022E0000R01.htm

  T1 NO.
  Q2 Yes
  Q3 as described in the technical paper 4 GB will be recognized if you install Vista 64-bit.
  Q4 Yes as you can.

  Antivirus, for me, is better AVIRA antivir - http://www.free-av.de/en/index.html
  The application doesn't have a lot of resources and works perfectly. I use it for years.

  Good bye

• Satellite A200 - password disk HARD 'frozen' in the BIOS

  Satellite A200 computer laptop does not recognize the HARD drive.
  Reconstruction of the disk with Vista or XP - Pro (on another machine) have proved to be unsuccessful.

  Originally, continually blue machine armored and quicky restarted, Machine was infected by the virus and Trojans that I believe have damaged BIOS. The BIOS now appears to have 'frozen' a HARD drive password (unknown) which transfers any HARD drive new - perpetuating the problem.

  Any ideas or suggestions are welcome, thanks.

  Hello

  Usually, you should be able to remove the HARD drive password in the BIOS.
  You have to put the old HARD drive password must use ENTER to put an empty string as a new HARD drive password and you will need to confirm this
  Save the changes and restart again

  If this procedure is not possible or does not work then there must be something wrong with the BIOS, module ROM BIOS or motherboard.
  Maybe an update of BIOS/reflash could be useful, but generally all passwords must be removed before attempting a BIOS updates, which could be risky
  I think you should get in touch with a local ASP and need to ask for help, maybe the technician will be able to reflash the BIOS

  Welcome & good luck

• How Windows 7 directly editable either in the registry or the netsh commands to produce a 512 KB (524288) RWIN value as set forth in a capture of packets?

  Original title: Windows 7 RWIN.

  I can't wait to add yet another Windows 7 RWIN question, but the answer to the other questions leave me unsatisfied and I expect other institutions.

  When a TCP connection being established, Exchange - Yes RWIN values, even when one end is Windows 7.

  How Windows 7 directly editable either in the registry or the netsh commands to produce a 512 KB (524288) RWIN value as set forth in a capture of packets?

  Any contribution is appreciated - especially if they lead to a response! ;-)

  Thank you and best regards,

  TimM

  Hi Tim,.

  
  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking 
   
  Hope this information is useful.

• Error in the configuration of DNS server via the netsh command

  When I configure a local DNS server for my test-domain with the netsh command
  netsh interface ip set dns name = "LAN connection" source = static addr = 192.168.1.105
  I get a messge for error (translated from German):
  The DNS server is wrong or does not exist.

  But the local configuration of the DNS server always works perfect afterwards.
  The question now is: what netsh like not on my DNS server to produce this error?

  I get the same message too and the command works perfectly every time. It's probably a timing issue. I would ignore it.

• Satellite A200 - "findfirstchangenotification" message that appears at the beginning upward

  Hello!

  I have the Satellite A200 with XP on it. I finally removed VIsta and now whenever I start the laptop appears this message: findfirstchangenotification.

  Hello

  It is not easy to say what the problem is, but I imagine that some files are missing, but necessary to the application that starts with the operating system.

  What you can try is to start your computer in SafeMode (F8) to see if the same message. Otherwise start your laptop on a regular route and go to MSCONFIG and check list of registered applications automatically implemented. Try to disable some of them and watch carefully what happens.

  Intel Proset is preinstalled on your laptop?

• Satellite A200-1UV - how do I print the screen?

  Hello-

  I have Toshiba Satellite A200-1UV - can someone tell me how to view the screen, I'm looking.

  For example how to print 20-30 small jpg.pictures screen I see when I open a folder with photos of som I in the folder?

  Can I copy a put in a document, and then print or I can choose all the images and print them on plain paper?

  Thanks by

  Hello

  You can print the screen using the keys CTRL + print
  Now you must open a graphics editor like paint or something like that.
  In paint, click new file/photo and then use the CTRL + V keys to past the print screen.

  Welcome them

• Satellite A200-1NF needs time to read the USB flash drive

  Hello

  I have a Toshiba Satellite A200-1NF, model No.: ETA 6-055021FR works with Windows 7.

  My problem is that my USB is plenty of time to read the USB keys.

  Could you please help me to solve this problem.

  Thank you.

  Sorry, but for me the question is not clear enough... Satellite A200 recognizes the connected USB MemoryStick?
  If he recognizes the USB device connected, then everything seems to be OK.

  By the way: you said that the laptop needs a lot of time reading the USB...
  How long does it take and have you checked if the number is displayed using different USB ports and different flash memory sticks?

  If this is not the case, what to do

• Re: Satellite A200-1BQ, does not not after the screen saver

  Hi, I have a Satellite A200, 32-bit Windows 7 OS. When you use the screensaver to the PC stop responding. Have to spend because no response.

  If you have a report some problem send it please.

  Hello

  This means that Windows 7 hangs and does not answer only when the screen saver has been activated?
  Have you noticed the same problem with Win XP or Win Vista?

  If not then this behavior of the laptop could be related only to Win 7 and I think that it might be caused by the graphic card driver

  Remove the graphics driver that you have installed and test the screen saver using the common windows driver 7

  It would be interesting to know what is happening

• On Satellite A200 error message: could not open the ACPI ATK0100 Kernel Mode driver

  Hello

  I have laptop Satellite A200
  When I run the windows (vista) I get the following error: * 'Can t open ACPI ATK0100 Kernel Mode Driver.*'!
  I installed all the drivers and the error remains.
  I installed all the drivers on the Toshiba site, but the problem persists.
  The Device Manager shows me that each device is working properly.

  Someone at - it a solution?

  Thank you

  ACPI is the installation of your Windows operating system power management. If this fails you may need to run a recovery system on your computer. You can do this with the hidden partition on your hard drive, but this will erase all data on your machine. If this does not resolve the problem, you may consider making your hard drive, checked bad sectors, as this may have failed.

  I hope this helps. :)

• Satellite A200 - after Windows update games in the small window

  Hello

  I have a Toshiba Satellite A200 bicoeur vista Home premium.

  I have just re installed windows and installed a few games of children. They work well in fullscreen without problems. But after doing a Windows update that they are only now working in a small windowed screen surrounded by black.
  I tried to resize resloution you name and still nothing. But I can't work on it all can help me?

  Thanks in advance

  Hello!

  Have you tried to update the display driver? You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  You have reinstalled Windows with the Toshiba Recovery disk?
  What you have tried to solve the problem?

  Good bye

• Satellite A200-1AS - after you have reinstalled the blinking cursor

  Sorry for my English.

  Hello people
  I have a laptop Satellite A200 - 1AS PSAE0E - 025006GR,
  now, I wanted to format everything because I find very slow.

  Unfortunately I don't have the recovery cd not, and the 0 key does not work.
  Also new vista dvd buy code (recover partition not resolved vista partition) fine. But when you restart all black blink single slider.
  Downloaded drivers robson - unpacked 20070919162555.zip and during the next installation vista driver is loaded (which was eye appear as incompatible but no matter) Intel 82801 GR / GH SATA AHCI and still nothing...

  Could someone give me a tip?
  Thanks in advance

  The robson - 20070919162555.zip driver contains the SATA driver in the folder
  Robson Winall Driver package

  

  You will find the .ini, .dll files that must be added during the installation of Vista Setup.
  But first you must make sure that the HARD drive is recognized in the BIOS (first page)

• Satellite A200-13R - black screen after cleaning the fan

  Model name: Satellite A200-13R
  Model no: PSAE0E-011014GE

  I clean the fan, and I put new thermal paste to the processor. After finishing this job button press / the laptop works but the screen is black. The laptop shows that read the hard drive and the processor works well. I'm trying to remove the battery, disconnect the power, hold the button works / power off for 60 seconds, turn on computer with power plug, then stop, add the battery and restart * but the screen is always black *. I try to press Fn + F5 reboot screen * but again is black *.

  Any solution please?

  Thank you

  Nick

  You have disconnected the display while you cleaned up the laptop?
  Are you sure that the display is connected correctly?
  Check the cable?

  > The laptop shows that read the hard drive and the processor works well.
  How do you know that? Flashing LED HDD?
  You know, it's not easy to say what may be the problem.

  You can also try testing with external monitor.

• Satellite A200 crashing when moved or when the CPU usage is too high

  Well so recently my Toshiba Satellite A200 started crashing everytime I have to pick up the laptop or run any processes taking the CPU up to 100% usage.

  This means essentially no rendering 3D games and no Photoshop or current iTunes running at the same time, etc. Here are the best even if it happens only when the laptop is plugged and not when only battery power. I tried to use another AC adapter, and I cleaned the hard drive for a new installation of Windows 7 that never solved the problem. I even went so far as to update the BIOS.

  I am not quite determined that he is just a hardware problem, but I was wondering if anyone had suggestions about which party can act up on me. As I said still works like a dream when running on battery power.

  > Here is the kicker if this happens only when the laptop is plugged and not when only battery power.

  The energy saving switch to another profile, using the AC adapter.
  Maybe you can try to change the speed of treatment at a lower level and could increase the cooling method parameters in the energy saving profile when the AC adapter is in use.

  Otherwise, it could be a hardware problem and in this case, you will need a help of ASP.

• Satellite A200 - FN toolbar is missing from the top of the screen

  Hi all

  I just bought Satellite A200-1UP... now I have a problem in the bottom of the Fn. When I press on the iron tool isn't coming down from the top of the screen as usual. I don't know why. Although it worked normally... just sudden do not appear... but it remains active with brightness keys and etc... except the key to Tablet do not answer...

  I tried several times... but still does not the pleasure...

  Is someone can you please tell me why it does not appear as before or how can solve this problem?

  Visit Toshiba's European diver page and download the new version of the Toshiba value added package. Reinstall it, reboot, then your FN keys should run again! ;)

  Best regards and have a nice weekend