Satellite A200 - cannot boot from the recovery disc - code 1

Similar Questions

• Portege A200 - cannot boot from the recovery disc

  Hi, I have a Portege A200 and an original unused Toshiba Recovery CD.

  When I go to recover, the DVD drive just turns and turns and nothing happens. I have tried different methods of booting with the disk to like, by pressing the C key, select boot from CD/DVD or just turn it on with the DVD in the drive. Same problem, the disc turns right away.

  I also checked the drivers TOshiba download page and let down when I found out that there are several drivers for the same thing, like the 3 drivers LAN! Which should I use? Also, I can confirm that the CD/DVD drive works fine because I already loaded windows XP, no problem.

  Any suggestion is appreciated.

  Kieran99.

  Hey Kieran99,

  I also think that s is not a problem of the CD/DVD drive. If it turns over and over again once he recognizes a disc but it can t be read correctly.

  Regarding your question about drivers I think that it of fairly easy. I can recommend the vendor and device ID in Device Manager. With these identification numbers, you can search on this website http://www.pcidatabase.com/ to determine the LAN controller. All that s! :)

  In addition, you can check the ID s in Device Manager, if you click the LAN card properties > Details > PCI\VEN_xxxx & DEV_xxxx

• Satellite A10: Cannot boot from the recovery CD after the replacement of the motherboard

  Heres one in your brain is going...

  I recently started a format hard drive via the normal recovery CD, but it never finished as long as the power cut.

  Not to worry I thought, I kept all my data and a new motherboard was on order.

  The fitting of the new Council, I tried to boot from the recovery disc and all I get is 'non-system disk '.

  Then I replaced the HARD drive with a former to check the functionality of the Cd. The old disks (I tried two) both still booted from the cd and their HDs has worked fine once in windows.

  However...

  When I try to start any of these 'good' HDs from the cd nothing happens, nada zilch. In fact they will not start even to a 'Beginner PC' recovery disk either, so it's not the Toshy recovery disk.

  Another weird thing is when I go into the bios by pressing ESC the power upward and then F1 and try to change the boot sequence and press end to exit and save, nothing happens.

  If the CD is not defective because it is recognized in windows
  The recovery disks may not be at fault because the other disks also fail to start.

  This is not a drive problem hard as other HDs start normally (but not Cd)

  This could be a fault on the new motherboard, perhaps a problem with bios, or the sequence of events suggests something else?

  Any suggestions would be welcome

  Paul h

  Hello

  Long story. In my opinion you should write is a little shorter but with more useful information.
  I am interested in one thing: have you got a new mainboard or used one?

  To be honest, I'm also confused with the recovery disc you are using. The history is confusing.

  > so this isn't the Toshy recovery disk.
  Can you please tell us what kind of recovery CD are you using exactly?

• Satellite M40 - cannot boot from the recovery cd after format HARD drive

  Hello

  After my Satellite M40 - 133 being affected by the virus of security internet I had to wipe my hard drive. The virus wouldn't let me do anything, boot without failure or system restore. I wiped the disk and it still wouldn't load up. That's why I had to do a full erase of the disk including the hidden partition.

  After doing his now do not let my boot from the CD of restoration as it says invalid partition as his search for files that must be on the hidden partition. What can I do to get it started. I'm not bothered about to recover anything on the disc. If I remove the hard drive and put the recovery cd in, it excludes the disc and begins to start until he fails to see the hard drive.

  Outwardly I can link the drive to another pc and he sees it as a storage device so I'm glad that there is nothing wrong with the hard ware - help please

  Hello

  Can you see the HARD drive with all the details in the BIOS?
  If this isn't the case, then this means that the HARD drive is faulty or not fully compatible.
  If you can see the HARD drive in the BIOS, then this means that the HARD drive is compatible.

  But this should not affect booting from a bootable CD.
  Even if the HD would not be recognized in the BIOS, you should be able to boot from the CD. For example a live Linux CD has not only any disk HARD because the BONE would not be installed on the HARD drive, but it loads into RAM.

  The question is; Why you are unable to boot from any CD?
  Maybe the discs are scratched or the CD/DVD drive cannot read the disc more because of problems of laser lens
  If possible, try to copy/burn the Windows CD using another computer, and then try to start using the copied disc.

• I want to use the recovery disc for re - install my pavilion dv6, but cannot boot from the recovery disc?

  Now my system Windows 7 Home premium canbe accessed, but with a lot of problems. That's why I want to reinstall it. I burned my own recovery (totally 4 disks) successfully disks. I insert the first disc of recovery CD-rom and restart my laptop, but it can not recognized but in win 7 automatically. could you tell me how to use my recovery disks to reinstall the system win 7 when that is not totally broken?

  Hello

  Probably go to BIOS and configuration of the machine to boot from the CD/DVD ROM. Please follow the instructions from HP:

  http://support.HP.com/us-en/document/c00364979

  Kind regards

• Qosmio G35: Cannot boot from the recovery disc

  I'm in trouble from the screen of my Qosmio G35 showing lines vertical, gel, then a loop on and outside.

  I used the Toshiba factory restore disc to reformat and the problem remains, I went further and chose the maquis of the HARD drive option. Bad choices made by this beginner, because now it does not recognize the drive at all, prompting me to "initialize".

  Lines remain, but it is not the material of the screen happens during some process that I follow, OK.

  A friend more computer over the phone prompted me to go into the BIOS, but we cannot access them. Research on the web, I tried the F12 suggested, but this does not work, just push me through in a screen offering 'Safe Mode' etc.

  Any help would be welcome. Thank you

  Hello

  Usually the vertical display lines looks like a hardware problem, in my view, it could be related to GPU failure.

  In any case, we should start first of all the problem of CD/DVD drive you must check if the disc is properly recognized in the BIOS.

  For this, it must Access the BIOS press the ESC (if Toshiba BIOS) or the key F2 (if Phoenix BIOS). Please check these two options because I m not 100% sure what the BIOS the Qosmio G35 uses.

  But like I said earlier the issue looks like a malfunction of the graphics card and you must contact the ASP in your country for assistance.

  Best regards & friend good luck

• Iconia W3-810 cannot boot from the recovery disc

  Hi, I have a 32 GB Iconia W3-810.  The original recovery disk was lost.

  I made a Bootable DVD of 8.1 and also Win 8.1 bootable USB key.  These two have been tested on another laptop, and both can start this laptop to the installation environment.

  I also followed the guide to enter the BIOS of the Acer Tablet settings and change the boot order and change remove secure boot option.

  Unfortunately the unit keeps trying to start in Windows 8.1 - one who is full of viruses and should be flattened and start over.

  Help, please...

  Many of these cables power the Tablet via the splitter, but do not provide power at the side of the data cable from the side power (I don't think I explained that well). They are designed to power your device on the motor side while allowing access to data on the other side. If connected:

  Tablet- + - power
  
              |
  
              |
  
             DVD

  The Tablet receives power supply and Tablet provides the voltage and sends and receives data from DVD, but power does not give voltage on DVD. This means that the DVD does not necessarily receive the budget power that he needs.

  If you can, try the DVD connected to a powered hub. Turn upwards and actually to work are two different things, and tablets offer far less than the maximum power on their USB ports.

• How can I get WIndows8 TouchSmart to boot from the recovery disc

  How can I get WIndows8 TouchSmart to boot from the recovery disc? With the recovery in the drive disk when I do a reboot or stop and start it does not read anything from the DVD player. My computer is a HP TouchSmart 23-D160QD.

  @AirForce9731,

  You may need to change the boot order to boot from the DVD drive first.  The steps to do this are in the document below.

  http://support.HP.com/us-en/document/c00364979

  These are recovery disks made by the recovery discs sent by HP?  They will not work in a different system (you will receive an error message), but you are able to get the boot floppies in a different system?  They should be able to start up to a point where the error message will be displayed.

• Can not boot from the recovery disc - 0x000000D1 Driver_IRQL_not_less_or_Equal

  original title: cannot boot from the Vista recovery disc

  A real problem. Vista is prompting me to boot from my recovery disc and allow the repair of Windows. However, when I insert the disk it shows loading Windows, but once he starts to launch I get the BSOd with the "Driver_IRQL_not_less_or_Equal" error report with the error code Stop 0x000000D1. I searched on advice but all I can get into the repair mode, but I can't. F8 does not work in safe mode. Week last ChkDisc has run on every start and yesterday I received a number of parts of Vista won't load does not with error reports. Today, it started with Windows can not load the warning and instructions for use the recovery disk... I'm in a loop as I cannot cross the BSOD! Help please

  Mick

  Computers are strange animals. After my response to you, I had another attempt to go beyond the blue screen. Hey hop this time my computer decided that he had enough rest and proceeded without delay to start and I would like to action, the recovery disk. There then reinstall Windows Vista and am now to a new computer! It's time to move to Windows 7! The only thing I did yesterday was to unplug my printer to my laptop!

• Satellite M45: Cannot boot from the CD-ROM or HARD drive

  I get the following messages...

  WHEN BOOTING FROM HDD: "Invalid partition table".

  At the START of the CD: "No Bootable CD in ATAPI CD-ROM.
  By so, even though I have the recovery CD and the computer can not read them.

  I tried to change the order of boot without result. Created a bootable CD Bart, who works in my other computer, but not in this laptop. Are there special drivers, I need for this CD?
  I'm out on this one.

  Thank you

  Hello

  I think that your partition on the HARD disk is damaged and so you cannot boot from the HARD drive.
  In this case, the HARD drive must be formatted completely and then you could try to install the OS.

  It seems also that your drive cannot recognize the CD bootable (WinXP?) and, therefore, it of not possible to boot from the drive.
  Well, it really stupid s :_| situation really stupid!

  However, did you try to boot from another CD? For example Microsoft Windows original CD?
  If not I recommend you to do and eventually the reader will be able to read the CD.
  If this isn't the case, so I think that the reader must be checked. Possibly it also corrupted s.

• How can I configure Satellite A300-148 boot from the recovery partition?

  Hello

  I had some problems when trying to install MAC - OSX, for her, where the partition table is deleted, then I retrieve the entire score as it is, but I can not start in any case.
  Then I decide temproraly install another copy of vista drive Vista (not the partition), then set up my laptop to boot from the recovery partition and reinstall the good copy.
  My problem is, it's all here, the only problem is, I need to configure the system to boot from the recovery partition.

  My device is:
  Satellite A300-148

  Thanks to the device.
  Ahmed.

  Hello

  If you have already changed the partitions of HARD drive and deleted files from the HARD disk, then your HARD drive recovery is too bad!

  But to make sure that the HARD drive recovery is not possible please press F8 immediately after the power of the laptop. Usually a start menu should appear and you should be able to choose the option called fix my computer. Then you should be able to choose recovery option.

  But like I said that this is only possible if your HARD drive was not formatted!

  If you have formatted the HARD drive and changed partitions then you will need a Toshiba DVD recovery that you have not because you didn t he create at the beginning. Is this good? Well, then you must order the recovery DVDs if you want to retrieve the laptop to factory settings.

  Welcome them

• Satellite A200: Can I use the recovery disc without wiping the drive

  I read the threads on this forum, but I did not come with an exact answer to my problem.

  With my regular PC, I got a disc of Installation of Vista, which is also a recovery disk (like that could do with XP). One of the most useful things is that when you start from the disc you have an option to "fix" the system, which means that all the vital files (such as the bootloader...) will be restored, but otherwise all data will remain. This is extremely important when for example you install a dual boot with Linux, when often Vista refuses to start and to repair the boot loader has solved the problem. Of course it can easily and quickly fix all kinds of other problems in the system as well.

  My laptop Toshiba A200 (otherwise a wonderful machine), came with the Toshiba product recovery disc. From everything I read on the forum and what he says on the disc itself, I understand that it only allows a total reinstallation of the system, set at the factory, wiping your drive and everything on it.

  Toshiba really leaves us without a 'repair' option '?
  I find that quite amazing, because after all, I paid for the Vista operating system, so why shouldn't I get the options I would have if I had an original Vista disc?

  If all the above I have is right, it means that if I want to install a dual boot with Ubuntu and would get a bootloader problem, I loose all my data when I have to repair the boot loader? (A problem which, with the option 'fix', takes only 5 minutes to fix!).

  I would like to hear reactions, solutions, suggestions or alternatives.

  Thanks in advance,
  Yossi Beck

  Hey Yossi

  I think you have misunderstood something!

  You received with the image of Toshiba Toshiba Recovery CD! The image contains drivers Vista OS, Toshiba, tools, utilities, and additional programs!

  Please don't compare this disc for the original CD of Microsoft Vista and don t mix it!

  So using this disk, you can set the laptop back to factory settings!
  This is very useful because this procedure takes about 10 minutes only and you get everything functioning OS with all the drivers, tools, etc.

  Please note that no all users and customers who buy these phones are technicians and scientists ;) but simply newbie and such possibility of recovery is always welcome!

  but the use of this recovery CD format the whole HARD drive and erases all partitions.
  That is why it s advisable to back up the data before using the recovery CD/DVDs

• Satellite A200 - 20 c - need the recovery disc

  Hi you

  I top model satellite A200 - 20 c, serial number is 18232821K.

  I'm trying to find information on my lab top, but it has give me is the error, and this model, not found, could you tell me what the problem is and what I can do.

  2nd, I need to order Recovery DVD becose my cd is not ok and show me some file missing I don't know what the problem is. Tell me how to order the DVD and my laptop is supported for windows 7, tell me how bud from vista to win 7.

  Thank you

  Hey,.

  As far as I know for notebooks, it s not possible to order an online Toshiba Recovery disk.

  For older computers, you will need to order a disk at an authorized service provider. List of them which you can find here:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)

• Cannot boot from OS recovery Disc - hard drive again

  Hello.

  I had some problems with my computer for a while.  This week it stopped starting up, so I ran diagnostics from the utility partition, and it seemed pretty clearly indicate that the hard drive had a few significant flaws.  This was not unexpected, and I have all my data backed up on an external drive, so I bought a new hard drive.

  The problem I'm having now is that my system does not recognize my operating system recovery disk.

  I made sure my CD player is set as a first priority and tried to force it in the start menu, but it is on a black background with a blinking cursor, or says "No Boot Device available"

  I tried the drive in another computer, and I can read here very well.

  I ordered a replacement from Dell recovery disk, but I don't know if there is anything else I should try.

  Any help is appreciated.

  Yes, if the reader is made bootable.  See here:

  www.computerhope.com/.../ch001366.htm

• My product key is not accepted when booting from the recovery disc even if I use the product key supplied by the manufacturer.

  I wanted to clean up my computer so I copied the data on an external hard drive and then partitioned and formatted my hard drive is internal. I then ran the recovery CD provided when I bought the computer of Evesham Technology.  However, when I provide the product key which is glued on the case of my PC I get the message "the product Id you entered is not valid.  What should I do?

  Kind regards
  Eric

  How to activate Windows XP
  http://support.Microsoft.com/kb/307890/en-us

  See the section titled: "how to activate Windows XP by phone.
  Also, make sure that you do not confuse the letters and numbers (number 8 for the)
  Letter B, etc.).

  How to contact a Microsoft Product Activation Center:
  http://support.Microsoft.com/default.aspx/KB/950929/en=us

  Microsoft Activation centers worldwide telephone numbers:
  http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx
  (This site is for activating Volume License, but if you call, they will help you)

  The phone number is not working:
  Microsoft Wordwide contacts: http://www.microsoft.com/worldwide/default.aspx

  Users of Windows XP - Genuine Advantage Notifications:
  http://www.Microsoft.com/downloads/en/details.aspx?displaylang=en&FamilyID=afd45b36-3d77-4259-801c-d31a9a90cdcf
  (This tool will confirm that the copy of Windows installed on your PC is genuine and authorized)

  J W Stuart: Http://www.pagestart.com