Satellite A200 PSE3E stops after the connection

Similar Questions

• Satellite A200 (PSAE0C-AH308C) - after the BIOS black screen update

  Hello

  I have a Toshiba Satellite (model No. A200; Part No. PSAE0C - AH308C) and to install Windows XP on a version already corrupted Vista (which had 4 partitions, that have been corrected, erased, then reformatted in a solid block). Now, I have installed all the appropriate drivers off Toshiba Canada support site...

  Everything worked, but I wanted to see in Windows (since I just got this computer) if everything was in place and working normally until I installed Ubuntu... Then I did the update to the BIOS flash. The program is supported in two formats, one for Vista and one for XP... for XP has a more high at 5.20 and Vista BIOS version the 1.80 revision of BIOS... that are marked as being updated by the Toshiba site. I opted to download the latest version of the BIOS.

  Things got ugly as soon as I unzipped the self-extracting program. First of all he said he could not find a .dll file (even if it is clear from there), so that seemed as if it started to Flash the BIOS but has not finished (it was just what happened when I opened the program)... I think he got to the ROM of compensation but did not have any code in there... Windows attempted to close the program because he did not respond, and I tried to take the program... had the same .dll error, but this time, the screen of the program was just gray...

  Given that this program is not Flash the BIOS unless the user selects the button "Flash BIOS", I have reason to believe that it was a bug in the program, or a combination of it and Windows comes to interfere (no program were running at the time, while he was supposed to be a dedicated flash). I can only flash in the Win.

  Now, I rebooted the computer, twice... the screen turns black, the HARD disc spins, the DVD drive has done his usual clicking sound when the computer starts, but it seems to stop as there is no BIOS entact.

  Can I replace the BIOS chip? There is no way for me to access the BIOS at all.

  Thanks for any help on this

  Thank you & best regards

  Muhammad Asif
  Manager

  THE COMPUTER HUT

  Center of the screen:
  F-115 trade place treat Saddar Karachi.
  Branch:
  G-31 place of trade treat Saddar Karachi.
  Headquarters:
  711-712 treat Trade Square Saddar Karachi.

  Tel: (+ 92-21) 2765359, 2734131 (Ext) 601
  Fax: (+ 92-21) 2724968
  Cell: + 92346-3277193
  E-mail: [email protected]

  Hello

  Unfortunately, the BIOS update has failed and now BIOS is damaged. For this reason, you cannot start and use your laptop. I agree with Luke. Please contact nearest Toshiba authorized maintainer and ask for help. Talk with them and I am sure that you will find the best solution to this problem.

  Satellite A200 is quite long on the market and it is hard to believe that updating the BIOS on the Canadian page may have a bug. All updates are tested and used by millions of users and service providers. If there is something wrong, I do not believe that this update will be available on the page of public support.

  In any case, contact the nearest service provider and explain the situation. Believe me this is the best thing you can do now.

  Good luck!

• Computers stops after the connection to the server

  Hello geniuses.

  I'm having a strange problem and I know it won't be easy to diagnose, but let's give it a shot.  I have two iMacs in my studio, a 4 k and a 5 k, with El Capitan 10.11.2 and both connected to an ethernet network and talk to a server on a Mac Mini (latest OS and OS X Server).

  I mention the server, because I think it may be interesting, but that's just a guess.

  Basically both of these computers have a strange inability to stop.  You choose stop and they go through the motions all the way to the black screen with the toothed wheel turn, and then it just lingers there.  Forever.  Well, at least 24 hours because it is the longest, that it went unnoticed at the time.  Usually, I wait a few minutes and then make a stop of the force.  (I wait a few minutes because sometimes, not often, but sometimes, the computers will be correctly closed.)

  Both machines are wired on the server and use frequently shared fire (SMB and AFP) to load files on networked drives.  Yet once again, I mention this because this is the common point between these machines that seems to be the exception to a common use, and I wonder if the connection to the server is the process that prevents computers from closing properly.

  If anyone can help point me in the right direction would be great.

  Thank you!

  Well I guess this problem is unique to me, however, if someone else liquidate the same problem, I think I have it solved.  I changed the file sharing preferences to just AFP (disabled SMB).  This seems to have solved a variety of issues that I had with my network, including iMacs hanging on closing down.

• Satellite A200 qwerty stop after 5 years used

  Hi, sorry for my very bad English. I am sam from france.

  I have a laptop A 200 with vista. Yesterday, I used the computer and during this time, the computer give me a tuuuuuuuuuut and after to write a UUUUUUUUUUUU in the navigation of windows. and directly the stop qwerty.
  Now when I start the computer, enter a subject message to repair but need a querty for click.

  I have a querty outside but what can I do to fix this problem.
  Thank you

  Not sure if I understood, but it looks like you have some problems with the internal keyboard. Right?
  You are able to use the external USB keyboard?
  If you can use the external keyboard, then the internal keyboard is defective and must be replaced.

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• stop work after 30 seconds after the connection of 32-bit applications

  I have a problem that some of my 32-bit applications (vlc.exe, sapphireeffectbuilder.exe... etc) fail to start if I try after 30 seconds after the connection to windows. I managed to identify only a couple of processes that stop after 30 seconds of recording. These are:

  SearchProtocolHost.exe
  SearchFilterHost.exe
  IAStorIconLaunch.exe

  I'have tried to re-indexing and reinstall the intel RST service but no luck so far.

  I can see the vlc.exe in the system tray, but nothing of lance. Help, please. Thank you

  Hello

  Please contact Microsoft Community. I appreciate your efforts to solve this problem, I'll probably help you solve this problem.

  This problem might have occurred because of these reasons:

  1 conflict between third-party applications.

  2 corrupt system files.

  3 virus.

  Try the steps listed here:

  Method 1:
  I suggest to start the computer using safe mode and check if the problem persists or not. If the issue happen not in Mode without failure, you can set up your computer in a clean boot and check if it helps.

  Step 1:
  Start the computer in Mode safe. At the start of the computer Mode safe with the minimum set of drivers and files.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2:
  If the issue happen not in Mode safe, we will set up your computer in a clean boot state and check if it helps. Setting the system in a clean boot state will help you determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7
  http://support.Microsoft.com/kb/929135

  Note: After the clean boot troubleshooting steps, see the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  Method 2:
  If the problem persists, I suggest you to virus scanner to make sure that the computer is virus-free.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note:
  (1) the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  2) if you run the virus scan of the program which is infected with the virus will be deleted. Therefore, reinstall the program. Also, if files and folders are affected by the virus, while they might even get deleted.

  Method 3:
  If the problem persists, I would say allowing you to run the auditor of file system (CFS) analyze and check if it helps.

  Use the System File Checker tool to repair missing or corrupted system files
  http://support.Microsoft.com/kb/929833/en-us

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• T42 - stop and restart after the connection

  My T42, running on Windows XP, suddenly stops right after the connection and while the hotkeys on the loading screen.

  A message in white letters on a blue screen starts like this:

  "A problem has been detected and windows has been suthdown to prvent from damage to your computer.

  IRQL_NOT_LES_OR_EQUAL

  If this is the first time you've seen this stop error screen, restart your computer. "If this screen appears again, follow these steps:

  And the product message points to check any new hardware or software installation. I have not recently installed a software or hardware, so I'm a little lost on how to proceed from here.

  No clue on what could be the problem or any recommendation, short doing a full recovery from a recent backup?

  Any help will be much appreciated. Thenks.

  = UPDATE =.

  After running a few tests using the blue Access IBM button and PC Doctor 2.0 running, memory tests have shown the following results:

  Fast memory - all sockets - failed

  Fast memory - Support 1 - spent

  Fast memory - take 2 - failed

  This seems to indicate that one of the two memory is faulty. This hypothesis is correct?

  If so, what should be the next step? My laptop is out of warranty. I should bring it to a repair shop, or could I order the replacement and install it myself easily?

  I am not versed in repairs to equipment and feel a bit discouraged to start to mess with storage media...

  Any advice, please?

  Thank you

  It is probably a faulty stick of RAM in the second location rather than the power socket. Best bet is to remove the module RAM then see how it goes.

  Second is really easy to access. It is under the laptop - there is a small door in the middle of the base set with a single screw. Remove the screws and remove the door to expose the RAM module. Pull the wire staples on the outside of the restraint SODIMM socket and the RAM module should appear and then remove. Replace the cover and try the laptop again.

  IF you must replace the T42 uses to off the shelf of a DDR SO-DIMM, PC2700 speed RAM - needs. Will take up to a 1 GB module in each socket. First is harder to do because he must remove the keyboard to get home. It is only 4 screws but can be a bit tedious for a novice.

  Edit: The instructions for IBM appropriate here: http://www-307.ibm.com/pc/support/site.wss/MIGR-46513.html

• New Satellite A200 is restarted after installing XP

  Hi all

  I hope someone can help with this problem.
  I have a new Satellite A200 and made in the wake of the SP2 and matrix storage drivers.
  I completely deleted all partitions on the disk and installed XP (slipstreamed version).
  All going well until the first reboot and then it restarts just over and over again.
  If I have safe mode of choice it loads correctly and I can't install drivers etc.
  I wonder if it is a BIOS issue?
  I tried to update using windows bios update for XP and it will not allow in safe mode.
  The reboot happens before even starting XP screen appears, hard drive blinks twice, then it power cycles.
  I hope that I'm not the first to encounter this problem.

  Any help would be appreciated.

  Hello

  Mhhh very strange to me, it looks like a software problem!
  In Windows XP, the default setting is for the computer to automatically reboot when a fatal error occurs. If this fatal error only occurs when you stop, the system reboots automatically.

  Have you noticed the same course the Vista OS?

  What you could do is to install the Vista from the recovery CD again, and then update the BIOS to the XP version.
  After this procedure install the XP with all the service packs and the compatible Intel matrix Storage Manager

  Good luck

• having suddenly emits turn off my computer as well as the questions after the connection

  It started randomly a few days ago.

  When I stopped everything simply is not extinguished. It will let 10-30 minutes and just restart and brings me back to connect. After the connection of that my computer strikes a blackscreen im could not use the mouse and enter the Manager tasks, but nothing else, after a minute or two my bottom and loading of the task bar and I can use my computer normally.
  what I can tell you is...
  I started in safe mode and this didn't happen.
  I ran msconfig and disabled all non-microsoft processes and it is happened
  I opened the event viewer and there seems to be a large NUMBER of critical errors from the night, I first shut down my computer and contained errors (25/08/2012 around 11:30)
  looks like this https://www.dropbox.com/s/1rkitvaaq69rlkq/Lucas-pc%20events.evtx (tell me if you can show that)
  Also I tried to restore my computer to the 24, but he won't do it for some reason any.
  Im running windows 7 64 bit edition Home premium
  16 GB of ram
  Intel 3, 5 GHz 17-2700 k
  2 x radeon hd 6870 in crossfire

  Hello

  1. have there been recent changes to the computer before the show?

  I suggest to follow the steps provided and check if it helps.

  Method 1: Try turning off the auto reboot on the computer.

  a. right click on computer.
  b. click Properties.
  (c) advanced system settings.
  d. Advanced tab.
  e. startup and recovery settings.
  f. uncheck automatically restart.

   

  Method 2:
  The problem can also be caused by your security such as anti-virus program or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.

  Disable the antivirus software:
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3: Why my screen is black when I start Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Method 4: as make that you followed the exact steps from the link.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

   

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Hope this information is useful.

• Why don't I have easily select my questions open after the connection support?

  Why don't I have easily select my questions open after the connection support?

  When I connect support communities, I have still no clear idea where to find my support questions which remain open to check updates.

  Seems to me that this should be a great, distinct and separate button on the homepage of support after you have connected.  "My open issues Apple Community Support."

  Is this too much to ask?

  Steve

  1. Click / tap your username
  2. Click / tap 'manage subscriptions '.

  

• Satellite A200-1AE (PSAEC) - when the new update would be available

  Hello.

  I have Toshiba Satellite A200-1AE (PSAEC) and the latest BIOS is since 2007.

  Toshiba means update?

  I think that old "deserts" Toshiba series and that he cares only for new.

  Unacceptable

  Hi mate

  Why should Toshiba BIOS update?
  There's a problem with your laptop that should be solved by the BIOS updated?

  To be honest, I don't know if the new update of the BIOS would be available for an A200 but if something would not would be not wrong with the old BIOS Toshiba provide an update
  One of my friends has a laptop A200 and its working properly

  Welcome them

• Satellite Pro L500 - stops when the power cord removed

  Toshiba Satellite Pro L500 stops when the power cord is removed even with the battery to 100%. I removed the battery and all the indications associated with battery answer correctly. For example turns off, Toshiba Health Monitor also indicates when the battery is removed. If installed Health monitor indicates that the battery is at 100%.

  Someone please help. I have not installed anything new.

  Hey,.

  For me, the matter is clear: the battery can't hold a charge so the laptop will be shut down because it has no power.

  I think you need to replace the battery with a new one and you can get a provider of service authorized in your country. Simply contact the guy and ask that they can tell you how much it would cost.

  You can find a list of all FSA here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• 7.0.0.102 crashes immediately after the connection

  After update to Skype 7, it crashes immediately after the connection.

  I don't have facerig or FFsplit or any webcams. Update of Windows Firewall is disabled.

  The event logs show this:

  Name of the failing application: Skype.exe, version: 7.0.0.102, time stamp: 0x54897add
  Name of the failed module: Skype.exe, version: 7.0.0.102, time stamp: 0x54897add
  Exception code: 0xc0000005
  Offset: 0x00d527d7
  ID of the process failed: 0x1e7c
  Start time of application vulnerabilities: 0x01d029890c579caf
  The failing application path: C:\Program Files (x86)\Skype\Phone\Skype.exe
  Path of the failing module: C:\Program Files (x86)\Skype\Phone\Skype.exe
  Report ID: 58eb96c6-957c-11e4-aae2-00224d806fdf

  Any ideas that I can do to make it work again?

  I don't know, but maybe it's one of several cases in the latest version of Skype 7.0 is not able properly to interpret data from the BIOS. At least, that was the issue with the cases already reported with this error message:

  Exception code: 0xc0000005

  Offset: 0x00d527d7

  A fix may be available in one of the next versions of Skype. In the meantime, the solution is to uninstall version 7.0 and install the 6.21.0.104 previous version.

  http://download.Skype.com/MSI/SkypeSetup_6.21.0.104.msi

• Outlook express hangs after the connection with the mail server

  OE6 hangs after the connection with the mail server?

  Make sure that the other machine is not check that the server so often a machine is not problems because it cannot be verified.

  Try to delete the account, compact the folders and close OE and reopen it and add the account back again.  Also make sure that the antivirus software is not interfere (see www.oehelp.com/OETips.aspx#3).

  You can also telnet to the server directly from this computer to see if it works (see http://techhelp.santovec.us/pop3telnet.htm).

  Sometimes it gets stuck in a message on the server and it can not get downloaded by OE, so it may be necessary to remove the message from the server, but if the other machine got, maybe it's not the question.

  Steve

• XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  XP key wep changes for new router linksys after the connection. you need to reinstall the WEP every time you start from the top.

  Hello

  Let us perform the steps below and check out them.

  a. click "Start," "Control Panel", then "Add or Remove Programs". In the box "Currently installed programs", find the name of your wireless router. Click on the name of the software, and then click 'remove '. Click 'Yes' when prompted to confirm.
  b. click "Start" then "run". Type "Services.msc" and click "OK". Select 'Wireless Zero Configuration'. Click on 'start '.
  c. click 'Action', 'properties '. In the drop-down menu "Startup Type", click on the arrow and select 'Automatic' to assign the commissioning of automatic Wireless Auto Configuration. Click on 'OK '.
  d. restart your computer.
  e. right click on "Wireless connections" icon Select "View available wireless connections." Click on "change the order of preferred networks. Select the name of your network, and then click "Properties". Erase the old key and enter a new. Click the checkbox next to "Automatically use that key." Click on 'OK '.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.