Satellite A210 PSAFGE - no display after the update of the BIOS

Similar Questions

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Satellite L300-1 has 3 - after the BIOS update, I get a BSOD

  I have a Satellite L300 1A 3 MODEL PSLB8E. I decided to update the version of the BIOS, thinking that he can resolve my issue of ethernet controller.

  But after the update, my laptop goes on infinite blue screen of death. How can I recover from this injury?

  Can someone please help.

  Hello

  Did you choose the good BIOS update for your model? Was it for Satellite L300 PSLB8E?

  What code you get BSOD?

  After the BIOS update you must always load the default settings. Maybe a bad BIOS setting is causing this BSOD.

• Satellite A300-1ID - no display after the update of the BIOS

  HELLO GOOD EVENING,.

  I HAVE this TOSHIBA SATELLITE A300-1ID, as described above, happens them have BEEN updated THE BIOS AND everything to HIT PC turned off and there is no power were all CURRENT PIC BY me UNLESS I get TURN OFF AND NEVER HAD ANY IMAGE or EVEN RELIANT YEAR EXTERNAL SCREEN to.

  BUT IF YOU TURN on THE PC NORMALLY, THE COOLER STARTS AND IS FUNCTIONING NORMALLY, THE CD and DVD DRIVE AND HARD DRIVE AND THE LIGHTS have ACCESS, so DO NOT image on-screen, already tested RAM MEMORIES HAVE an OTHER TOSHIBA SATELLITE OF MY WIFE AND WORKS WELL, I despair A PC because I NEED TO WORK AND NOTHING to TALK WITH computer THAT TELL me WHAT COULD BE THE BIOS or graphics HIGH card.

  THANK YOU NOW AND WAIT FOR YOUR ANSWER

  Hello

  Seems that something was wrong during the update of the BIOS
  For me it s really amazing because something like that never happened to me and I have updated the BIOS very often

  What to say that you will need additional assistance of Toshiba ASP. I think that the ROM module must be flashed once more using a disc of crisis.

• Satellite A200 PSAE0E - no display after the update of the BIOS has not

  Hi all

  I have Toshiba A200 PSAE0E. I got the Vista OS to Xp.
  When I tried to upgrade the BIOS setting, the system frozed.

  I reformulated the system using the power button. There is no display on my screen when restarting.
  I tried to restart by pressing F1, F2, key to the House and even removed the battery for a while, until what there is no display on my screen.

  I even tried connection and an external monitor, but that also there is no display.
  At the moment I don't have any sort of recovery disk.

  I would be very happy if someone could help me.

  Hello

  To me, it seems that the BIOS update procedure has failed.
  For no apparent reason has frozen the system and you have interrupted the update procedure.

  According to mu ROM module (where the BIOS is stored) has not been flashed properly and this is the reason why you cannot start the laptop.

  In this case, you need the help of ASP I know, this really stupid s situation but I'm afraid there is no alternative to m.

  I think that the technician will try to flash the ROM module using a special BIOS and then the cell phone should start properly if all goes well. I'll keep my fingers crossed for you.

  Good luck

• Satellite A210 - turs screen off after the Windows startup screen

  When I start my windows there is the splash screen. After that, my screen goes off and cannot log on to windows.
  Satellite A210
  ATI Mobility Radeon HD2600

  Where can I get some old drivers for the ATI Mobility Radeon HD2600, that I can install without starting windows?

  > Where can I get some old drivers for the ATI Mobility Radeon HD2600, I can install without starting windows?

  Please don t get me wrong, but I think you're on the wrong track.
  (Graphics card, LAN, etc.) device drivers must be installed in the currently running system (i.e: Windows OS, etc.)

  I m sure; pilot isn t the problem if nothing is visible on the screen.

  First of all, I would recommend you to connect the laptop to an external monitor/screen just to see if something would be visible on the screen 2.

  But just a question: have you tried to start Notepad using a boot disk (windows installation disc, the disc recovery Toshiba or similar?).
  Maybe the Windows system is confusing upward and therefore, you are not able to start the system? In my opinion, you should test this option.

• Satellite L350 - does not start after the BIOS update

  Hello

  I recently (yesterday) downloaded the latest version of bios update dated dated 25/02/10 2: 20 - WIN, after download and does run the software from the laptop immediately stopped working and stop. I am now no longer able to boot up the laptop at all, all I get is the power light on and the hard disk light flashes, I hear the spinning CD/DVD drive, but what is not screen anything, I don't think this is the start.

  Is there a way to fix this without taking it to a store/engineer, BIOS recovery?

  The laptop is a Satellite L350, I opened the laptop to try to reset the CMOS by removing the card mother battery (not sure if it would have helped), but as much as I know it doesn't have an or I'm not.

  Any help would be greatly appreciated.

  Thank you

  Andy

  Hi Andy,.

  Hmm... If the BIOS update failed, you can't do anything because only an authorized service provider has professional diagnostic and recovery tools to redo an update.

  So in my opinion, you must contact a service provider authorized in your country. Get in touch with the guy and ask for help. They will tell you what to do now.

  Here is their list:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  Good luck! :)

• Satellite Pro L300 - which improved after the BIOS update

  Hello users,.

  I just finished an update of the BIOS on Satellite Pro L300 using Updater Insyde Bios. I tried the Toshiba site to see what's new or what has improved since the update my bios 1.7version v2.2. But there is no search results. I also went to the site Web Insyde, but neither have they put up what has changed or improved?

  Is there a documentation or information which could help me to know how my laptop has improved or better after the update of the BIOS and what has changed since my update of the BIOS?

  Thank you

  Hello

  I assume you mean a changelog of the BIOS. Well, normally this document is placed on the Toshiba page where you can download the BIOS update.

  If you can't find such a t changelog, there is no available changelog. All that s!

  In addition the BIOS update should be performed only if it of really necessary. This means that if everything works fine, I don't see a reason to update because this update is a bit risky.

• Ports Satellite A135 - S2306 defective USB after the BIOS update.

  OK, I searched all over the internet and not found anyone else with this same problem, or anyone with a solution that worked for me.

  A few weeks ago, I had the common error of the BIOS reset itself and asking for a password at startup. I took my local Toshiba authorized repair center, and they have not taken care of him, no problem.

  Since the resume, however, all 4 of my USB ports have been going crazy. What happened in the following three steps (in order):
  -One of the ports does not work at all, won't provide any current or even recognize that nothing is connected.
  -The 3 remaining ports are now only recognized as USB 1.1 ports, not USB 2.0 as they were before.
  -Now, only a very small number of my devices is not at all, with three USB mouse and two unrecognized hard drives work (I get the error message "USB device not recognized" standard Windows when I connect them to one of the three ports).
  I am running Vista Home Basic (32 bit) with SP 2 and the new version of the BIOS is v1.60.

  Is this something people of repair caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  The old Duke

  Hello

  > What is the repair people caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  It is not easy to say. I think that would be best to ask guys why it happens or what they have done in the past.
  But have you set the default BIOS?
  Please do; access the BIOS (by pressing F2). Set it to default by pressing F9 (I guess) and save the changes. Restart the unit.
  Access the Device Manager, and then remove all hubs USB and commands from the list of devices. After that reboot the device again. Windows should recognize the devices deleted again.

• Satellite L30 does not start after the BIOS update

  Hello

  I upgraded my BIOS Satellite L30 and now the laptop will not boot. When I turn on the fan starts and that's it. I think I have updated the book with the bad BIOS... The laptop is only 1 day old... Is it possible to reset the machine to the default BIOS.

  Help, please...

  Hi Scott,.

  Unfortunately there is no easy way for you to go to your BIOS to its previous level. You need to entrust your laptop to a Service approved partner who has the necessary equipment to Flash the BIOS to the previous level.

  Kind regards

• Satellite L300D - does not load after the BIOS update

  I had to update my bios & it seems that that wrong has been downloaded about 3% by installing the laptop just die and not to revert to.

  There is no lights & there is no noise from the laptop at all.

  Can any ideas on how I fix?

  The laptop is a Toshiba Satellite L300D

  Hello

  Well, if the BIOS update crashed you can do anything because the ROM module needs to be reflashed. This is possible only with special tools and only an authorized service provider has such tools.

  Then please contact the nearest service Toshiba and ask for help :)

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Satellite L855 does not start after the BIOS update

  I downloaded the BIOS update and followed the instructions there during the installation, but on reboot (including the requested configuration), I get a blank screen. Intermittently, the CPU fan starts and stops. I think that the BIOS update failed, how to solve this problem?

  Thank you
  Neil.

  Hello, Neil

  In General when the BIOS is screwed up you need professional help and you should contact the nearest Toshiba service provider and ask for help.

  See also this thread. Perhaps this methid can help you too.

• Satellite L450D - nothing else happens after the BIOS update

  Toshiba Bulletin Board recommended 1 new message. Downloaded updated BIOS available. Frozen computer during the update and what would not be it. Now, the computer is totally dead. Power light turns on when the connected external CAP but nothing else. I did follow the instructions specific to Toshiba. Pleas advise.

  Thank you
  adrianevans

  Hey,.

  It of strange that the BIOS update gone wrong, because I already did several times and never had a problem did you run background applications they probably blocked the update?

  Anyway, what you can try is to remove the battery and the AC adapter / CC for a few hours. Then reconnect and try to boot up your laptop.

  In the worst cases the ROM module needs to be reflashed, but an authorized service provider can help you get rid of this problem. :)

• Satellite M50-130: no display after the passage of the external display in main monitor

  I have a very strange problem.
  My brother was on his user space as soon as possible and I managed to get the secondary monitor for main monitor and disable the screen of the laptop back, however, when it comes to me, it won't happen...

  Well, any help would be appreiciated.

  Hello

  Could you please be clearer? Is it possible to see something on the external monitor?
  Do you see something? What happens if you use the function FN + F5 device display?

  I put t know how you managed to set the external display as main screen because on my laptop, this option is grayed out.
  However, you should see the laptop if you will start Notepad in safe mode. Please check!