Satellite A300-1QD - start some time and memory errors won't test

Similar Questions

• Re: Satellite A300 of start-up problems and time

  Hello everyone,

  I have a laptop Toshiba Satellite A 300, and I have some problems with it.

  Problem is when I leave my computer (without external energy source) the time resets 2007, after several hours about (could be 6 hrs)., and computer quite often begins immediately after that I push the power button.

  I don't know the cause of the problem, because the battery is OK., computer running long on battery.

  I think the problem is in an internal battery in the CMOS, but I don't know if there is in portable computers.

  Suggestions will be highly appreciated!

  Kind regards
  Osman

  Hello

  > The problem is when I leave my computer (without external energy source) the time resets 2007, after several hours about (could be 6 hrs)., and computer quite often begins immediately after that I push the power button.
  Which is strange, I want to say the CMOS battery should not unload even the main battery is not empty as it s really strange to happen after 6 hours of non-use...

  What you can do is to let the laptop connected to the AC adapter for over 24 hours
  During this period the laptop should be lit!
  Then you can check the operation of the CMOS battery and if this behavior will always be

  If Yes, then you will need to contact a local ASP. Maybe the CMOS or the motherboard needs to be replaced

• Satellite A300-1QD - overheating and shutdown

  Hello

  I have the Satellite A300-1QD
  Serial number Y8805054Q
  PSAGCE-06E02DGR model number
  BTO Code T5800 / 2G / 2 G / 320 G/15WBT/DS2/L

  Over the months, I asked overheating problems. On two occasions, he also cut down. The laptop was on a hard surface and even the back. It still heats very quickly to the top, the only way is to have running on battery power saving mode.
  What can I do? How can I solve the problem?

  TX

  Hello

  It sounds like this dust is in the heat sink and your laptop should be cleaned using the jet of compressed air. This could blow out the dust from the cooling fans. You can get air to each computer dealer normally stream.
  Check this box!

  I clean my cell phone every 3-4 months and I m always asked how much dust out. I think that s important to clean but it only takes a few minutes. :)

• Is impossible to recover the Satellite A300-1QD (VISTA)

  Hey I have a problem.

  I tried to restore my Toshiba Satellite A300-1QD parameters by pressing the F8 key.
  I followed every step correcrtly, but when it came to 99% the computer was off all of a sudden.

  I don't know why, but maybe the computer got overheated or something, but I've had enough battery life.
  Then I tried to turn it on again and it is said there may have been some damage and he said I should put a "a CD to install Windows" as a first step, step says that I should choose a language, and step 3 says I should click on REPAIR.
  HE DIDN'T THERE HAS NO OTHER OPTIONS.

  Then he said: if I do not have the CD, I must contact the producer.
  As I remember, I do not have any what CD with my Toshiba when I bought a year or two ago.
  All I have is a yellow mini CD that says DISK of DRIVER on it.

  Is anyone of you know if a recovery CD is shipped with Toshiba Satellite A300?
  And no one knows what I have to do because I think I don't have it?

  Thanks in advance.

  > I can remember, I don't have any CD with my Toshiba when I bought a year or two ago.
  > All I have is a yellow mini CD that says DISK of DRIVER on it.

  You didn t get the recovery disk because there was an option to create the recovery disk clean you had to read the user manual
  The preinstalled tool called Toshiba Recovery Disk Creator can create a recovery disk
  Now it s too late you are not able to boot the system

  In this case, you must order the recovery disk;
  Here you can do;
  https://backupmedia.Toshiba.EU/landing.aspx

  Good bye

• Satellite A300-1QD - how to restore Vista preinstalled?

  Hey,.

  I made a big mistake, two years ago. I installed windows 7 on my Satellite A300-1QD but on the laptop Windows Vista was installed and I have no recovery disk, but I have the original serialnumber of it.

  Are there opportunities to put Windows Vista on the laptop without buying a new version of Windows Vista?

  welcome them

  steste123

  Hello

  If you don t have a recovery disk, you must order such a Toshiba drive directly to restore preinstalled Windows Vista with all the drivers and tools (factory settings):
  https://backupmedia.Toshiba.EU/landing.aspx

  But it s not free as far as I know it costs about 30 Euros.

  So I t understand why you didn't create the recovery disc yourself. Everything is mentioned in the user manual

• Satellite A300-1QD - two questions during the installation of windows XP or Vista

  Nice day
  Here's my problem:

  1. I just bought the Toshiba Satellite A300-1QD and since there is Vista based on it and I have Vista ultimate, I decided to install on the laptop.
  After I formatted deleated everything and I have the partition that I created a new.
  After that I installed Vista, now I'm at the point where it says complete installation and the blow bar is at about 2/3.
  My problem now is that it's now been 3 hours and nothing happens the dots next to the 'installation complete' is still occurring and disappearing.

  2 as the number one lasted so long I decided to install windows XP Professional, but when it loads after that I put the cd one has bluscreen place called chkdsk.

  What should I do now to get something on what works?

  Hello. I think that the partition table and boot loader are messed up and it's your problem. You can try to chek to find errors and format your HARD disk with a third parity tool and try to install windows again.

• Need driver SATA for installation of WXP on my Satellite A300-1QD

  Hello

  I have a laptop Toshiba Satellite A300-1qd and I want to install WXP on this.
  Now, I read the following document http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm

  But I can not found a driver like in the tutorial.

  I hope you can help me.

  Like Al - eX worte, you can download the storage on the Toshiba site manager:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers
  Laptop computer-online-online Satellite Satellite A series-online Satellite A300 => PSAGCE-online Windows XP

  Check this box!

• Re: Satellite A300-15 b Model_No: PSAJ4E and windows XP

  Hi guys,.

  I bought Toshiba Satellite A300-15 b model_No: PSAJ4E and I am trying to install windows XP. but when the installation message comes out says no hard drive found. I know that this question that I have to use the disk driver hard for allows me to do this.

  My Question is, I need hard disk drivers to support SATA in windows xp?

  Note: I have read in this forum that I can do it in the BIOS Setup, but I don't need this response.

  Thank you very much in advance...

  Hello

  Do the same thing as Niko for his Satellite Pro.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=35787
  I think that the chipset for laptops is the same - Intel® PM965 + Intel® ICH8M. You need load the files in the folder Ich8M_32 bits.

  Good luck!

• I haven't used itunes for some time and now have a new PC.  I've updated my account (change password) but when I connect to my music went?

  I haven't used itunes for some time and now have a new PC.  I've updated my account (change password) but when I connect to my music went?  I am working on Win 8 and still have part of my collection on an ipod.

  Unless you subscribe to iTunes game (which is not a complete solution anyway) your iTunes Library is on your previous PC - solution the easiest is to copy from here or from a backup.  For more information, see How to move your iTunes library to a new computer - Apple Support .  Previous purchases from the iTunes Store may be available for re - download - see download your past - purchases of Apple Support.

  If none of these approaches allows to recover the contents of your library, see user turingtest2 on recover your iTunes from your iPod or an iOS device library for a list of tools and methods that can be used to copy the media etc from iPod to iTunes.

• dad bought me a computer PORTABLE from NUTRIGEST I HAVE BEEN out of the CITY FOR SOME TIME AND LATER BETWEEN the AUTHENTICITY CODE PRODUCT, AND IT's not SAYIING VALID, BUT I KNOW THAT CANT BE REAL CODE IS

  dad bought me a computer PORTABLE from NUTRIGEST I HAVE BEEN out of the CITY FOR SOME TIME AND LATER BETWEEN the AUTHENTICITY CODE PRODUCT, AND IT's not SAYIING VALID, BUT I KNOW THAT can NOT BE TRUE

  If it is a new machine call or go to circuit city and get them fixed.  If they sold you the laptop, indicating that it included Windows XP then the onus is on them that provide you a valid COA and the product key.

  John

• virus: I struggled with the virus for some time and cannot get rid of them

  I have struggled with the virus for some time and cannot get rid of them. I bought a few programs, but they have also been infected. any suggestions for a really good virus buster.

  Hello

  First of all, an antivirus solution to an already infected system of loading is usually pretty useless. The bug will block all attempts to remove or load what it sees as a threat. Second, without knowing which virus you are affected by, it is difficult to be precise.

  You can take action include:

  (a) work in safe mode, there is much less likely that the virus is able to load and resist actively.

  (b) the safe mode, run utilities malwarebytes.org and AV solution that was installed * before * your infection.

  (c) post is back with a better description of what is on your system to learn more targeted advice.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Re: Satellite A300 cannot start, cannot use the factory recovery

  Hi all, I have a Satellite A300, which gave me problems in the past few weeks...

  I use Windows Vista

  There are about 2 months in the beginning of the laptop problem, it restarts itself automatically before enter in windows (while in the windows loading screen, no blue screen, screen just suddenly darkens and restarts itself), but it will get finally in windows successfully after a few loops

  but about 3 weeks ago, it just keeps looping and never get into windows, good news, it is that it can capture mode safe without problem

  I've done everything I can to try and save, as play with msconfig, drivers, removing the Rams etc, but not luck

  so, I save everything in safe mode and decided to restore the machine factory, but the problem is that when I boot up the computer by pressing 0 and enters the recovery screen, reboot loop will happen!

  any idea? or y at - it another way to restore to factory without touching the windows installed in my laptop? is it a hardware problem or software?

  I thought about the creation of recovery disks but my cd drive is not working properly, and I don't want to take the risk of buying an external cd drive not knowing not if the problem can be solved...

  Thank you very much!

  >.. .i don't want to take the risk of buying an external cd drive not knowing not if the problem can be solved...
  That of right, but you must understand that it is not easy on this virtual path to offer an accurate explanation and diagnosis for your problem.

  It is not easy to tell whether it is hardware or software related issue. best way to test is installation of recovery image. Recovery image is tested and if there are no some portable hardware problem should work fine. How to install the recovery image, which you can read on http://aps2.toshiba-tro.de/kb0/HTD1303440001R02.htm

  >.. .or is there another way to restore to factory without touching the windows installed in my laptop?
  Something like this is not possible. Windows that you use now needs to be reinstalled. I don't know why you the laptop restarts, but it's also the risk of recovery image installation. In case this recovery image installation will be interrupted, you will have two problems:
  -image of original recovery saved on your HARD drive will be unusable
  -you will not be able to start t

  In your situation the best is to minimize this risk and have original recovery DVD that can be used if something goes wrong.
  > but the problem is that when I boot up the computer by pressing 0 and enters the recovery screen, reboot loop will happen!
  Can you please explain what is exactly happening? Is - this laptop is simply cut off / go to the coast and then reboot again or what?

• Satellite A300: cannot start: blocked by Phoenix TrustedCore Setup Utility

  {SUMMARY: "Phoenix TrustedCore Setup Utility" appears every time you start, requesting a non-existent password.} How to get rid of this request? }

  This one is a little weird. We have a Tosh Satellite A300-193 mobile (Code manufacturer: PSAJ1E-01000XEN) purchased from July 2008 (via Getech educational scheme). We have (had) Kaspersky Anti-virus on this subject, but since his license has expired (and they didn't really like it), I was going to remove and install Avast.

  Kasperky removal instructions involve have their tool "kavremove" who say their instructions must be run in safe mode. So, after downloading the tool, I pressed F8 to boot into safe mode...

  ... And that's where things went wrong. Instead of typical black screen startup options screen, I got a splash screen at the level type, with a request for password of "Phoenix TrustedCore Setup Utility. We have never set a password on this computer, and I've never seen this particular screen before. After three bad guess (of course they're wrong!, and it does not matter if I leave the field blank), the unit turns off.

  Now when I turn it on, it just goes right to the request for password of Phoenix: I hit F2, F12, F8 or whatever it is. I can't establish why it should do, or how I can possibly bypass it. None of my password guess work (of course).

  I googled for hours (literally), closes the thing, I could find were instructions in [a post on the forum USA | http://forums.toshiba.com/t5/Windows-Vista-Windows-XP/Satellite-A205-Cannot-Access-BIOS/m-p/123075#M7749]. It was a partial solution: we can start the machine with this procedure (phew!).

  Unfortunately, it is not a permanent solution. After EACH stop, at the next start-up presents impossible demand "password." So it comes to pull the battery (again), to the phase of "discharging", battery, turn on and - it boots. Or at least, he has every time so far.

  This is going to be extremely painful. Any tips or to tackle the problem of pointers, which would be welcome. I will never see this request for password "Setup Utility".

  Thank you!
  David
  Edinburgh, UK

  Hello

  I think the password loss is the BIOS password.
  I m wondering why this password is displayed when starting if you have not set it

  However, the point is that the BIOS password can be removed if you n t know this password.
  Unknown BIOS password can be removed by a Toshiba authorized service partner.

• Satellite L100 113 starts slowly after upgrade memory

  Hello

  Toshiba Satellite L100 113 PSLA3E-02401JRU starts slowly after upgrade memory with Kingston KTT533D2-512 (512 MB) of memory.
  When I press the 'power' button, it flashes, starts the fans and HARD drive several times. Then it shows BIOS start messages by memory full 768 MB and starts Windows XP without a problem.
  This behavior is noticed only after "shut down."
  It does not happen with "restart".
  What can I do to eliminate this long "attempts" to start my laptop computer?

  Thank you
  Novomir Kovalenko

  Hello

  This problem appears before upgrade memory?
  Have you used exactly the same memory modules?
  If this isn't the case, then perhaps there are a few compatibility issues.

  Usually, after the insertion of the modules you must enter the BIOS and then save the settings. Please it and eventually the laptop will start without any problems.

• Satellite A300-146 - CD/DVD read and write the question

  I have Toshiba Satellite A300-146, model No.: PSAJ0E, 1 GB of RAM, Intel Dual core 1.87 processor, chipset Mobile Intel (r) 965 family
  I use the windows7 RC version.

  My DVD burner does not work correctly.

  (* 1) not read 700 mb CD and don't read do not more DVDs.*
  A few months ago he read sony DVD, read all CD and dint read some local DVD. Now, it is not read sony DVD and and all the CD that I used. But reads the local DVD...

  (* 2) a few times it can write DVD but most of the time this is not not writing DVD Nero 7 display of 100%, but the DVD is not written anything.*

  I use Vista drivers for my Window 7 operating system...

  3. should I install windows 7 drivers... ?

  4. are there specific drivers for DVD player. ?

  Experts or those who have recovered from the same problem. Please help me.

  Thanks in advance.

  Hello

  Maybe your CD/DVD drive becomes faulty... What do you think?

  But before you think to a new disk, you must remove the server - and lowerfilters in the registry. You can follow the workaround from Microsoft:
  http://support.Microsoft.com/kb/314060

  Also, make sure that the CD/DVD drive lens is clean. You can use a microfibre cloth to clean. This rag doesn't scratch the lens.
  Check this box!

  Finally and above all, there is no special driver for CD/DVD drive. It s a part of t Windows and can be updated.