Satellite A300 - disapperars video if I close the lid

Similar Questions

• Satellite A300 power suddenly goes out during the race for hours

  Dear users of the Forum,

  I am facing a strange problem in operation.
  My laptop Satellite A300 is suddenly down power during the race for hours.
  It is auto off not exactly. Not the way windows stop, is rather like strength to off (as when I press on & power button to stop force).

  This happens automatically, starting again, the screen saying "windows does not stop properly, start windows normally" is apperanig.

  I suspected virus infection, I tried full scan with nod 32, essential microsoft, kaspesky - 1 by 1 (previous uninstall and install the new), but all the antivirus intremediately scan stopped due to this power off.

  Watch movie also stopped in the Middle, attempted to convert the movie file format also was arrested several times because of this problem of automatic disconnection.

  I tried to run only on the power (remove battery) and got the same result.

  can anyone identify the problem? can you please give me the solution?

  smarjit1

  Hello

  I put t think it is s virus.
  En me it looks like overheating. Eventually the high internal temperature requires the laptop to close. This is done automatically to prevent the equipment from damage
  I'm not quite sure what could cause this exactly, but in most cases the dust inside the fans affects cooling performance and lead to a temperature higher than m.

  Higher temperatures could affect the RAM modules too, and perhaps that is the reason why some applications don't work properly.

  What to say; try to clean the cooling fans using a jet of compressed air and check out how the laptop would proceed

• Satellite A100 - options to close the lid for the laptop are not available

  Hello
  I have a Toshiba Satellite A100 - it came with Vista - I carefully cleaned the HARD drive and installed XP - I deleted the partitions etc. and started with a HDD in a perfect state of cleanliness.

  Then, I downloaded all Toshiba drivers that are available for my model.

  When I close the lid it still fully powered - there is no option to go into sleep mode, Hibernate etc in the options of "close cover" - the only option is the "status quo".
  How can I get the standby extended/standby/power options back?

  Your help would be appreciated

  Helen

  Did you installed Toshiba Power Saver utility?
  These options that you can find.

• Satellite A300 - nothing happens if I press the FN key

  Hi guys

  I own a Toshiba Satellite A300-15J with Windows Vista and the FN key no longer works. When I press FN key on nothing happens. Which driver do you think one should install?

  Thank you.

  Hey Buddy,

  I did a forum search and I found some similar topics are contiguous FN keys:

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=62172
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=62181
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=62112

  I hope that helps! :)

• Satellite A300-20 q are not on the tech support page

  Satellite A300-20 q are not on the tech support page. I can see 20 p, 20R, but not 20 q. Even a model automatic detector cannot find it in a database. Correct this error.

  Hello

  I don't know which pages or the database, you are meaning, but the Satellite A300-20 q is not available in all countries!

  This model was released for the Russia market.

  Other models of Sat A300-xxx are avaialbel on the other countries of South-East European/medium.

  Welcome them

• Re: Satellite A300-21I trying to start but the screen does not light upward

  I have a laptop Toshiba Satellite A300-21I 15.4-inch around the age of 2 months.
  He walks yesterday and received a message (very short)-initialization failed, see the event log.

  Laptop computer tries to start but the display does not illuminate.
  No prior problems.

  The indices of anyone?
  Stanley

  Hello

  You are able to access the BIOS?
  You see a Toshiba start screen that usually appears at the beginning?

  What happens if you press F8 at the beginning of the boot process?

  Please provide more details!

• External screen goes blank when I close the lid Satellite P100

  Hi all.
  I hope someone has an idea as to what is happening here.

  Sometimes I like to watch a dvd or use the center of the media on my HD TV. I use Windows Vista to make it.

  When I had XP installed, I close the lid of the laptop and watch them to my heart's content. Now with Vista, I need to have the lid open be able to watch on the external display. If I close to you then the external screen is empty, as if I unplugged the laptop.

  That makes me free! What worries me is burn-in screen, because the standby screen not turn on as I am watching video.

  Help! Someone! Anyone!

  AFAIK in Vista that you can use the same options as under WXp. check please supply option and you will find an option called when I close the lid. As option, choose no action.

  I think you should be able to close the lid while watching the movie on screen.

• Satellite 1800-314: when I close the lid it won't go in standby mode

  I hope someone can help.
  I recently had my Satellite 1800-314 (Windows XP) re-formatted and now when I close the lid he's going to sleep... the power light flashes orange, when I opened the lid still once, Windows stops and then restarts. I tried to install the Toshiba power settings, defining "when I close the lid, in standby mode", does not.

  Have uninstalled then Toshiba power settings and all the settings of ordinary power in the Panel of 'sleep', etc., but it REST did not return to standby mode.
  I'm tired now.
  Is there a simple solution that I'm missing?

  Grateful in advance for any help!

  Hello

  You know it's very important to install drivers in the correct order.
  The installation of common modules at the beginning is important because some drivers of Tosh need this application to work properly.
  If the energy saver has been installed on the operating system windows power settings will not work.
  Toshiba crash parameters the parameters of Microsoft.

  In addition, please check your BIOS preinstalled. Compare the version with the BIOS on the page. If your uses of the unit the old version, so try to update.
  But be careful. You must use the good BIOS and the right procedure upgrades.

• Satellite A200 AH3 stops instead of standby when I close the lid

  Hello

  I have a laptop Satellite A200 AH3. When I bought Windows Vista was preinstalled (I still drive recovery). When I closed the lid of the previous day (I mean the monitor turn off the HD, the cooling fan and all the rest). The light On / Off on the laptop turned to a flashing orange light.

  Then I opened the lid and Windows prompted me to the logon screen. This process occurred when the laptop starts on the battery, not when it is plugged. Everything was going fine.

  But I formatted the HD to install WIndows XP that I bought Windows vista seem to be too heavy for my laptop. So I installed Windows XP and the driver and the software available on the Toshiba site. Now when I close the lid, the Windows shut down very quickly (about5-6 seconds). However, it is a real firm. When I reopen it cover anything happen.

  Then I press the power button / stop and start Windows, normally (no screen saying that windows close annormally and no Safe Mode boot option). Even if I change the setting in the control panel/power Option or the Toshiba Power Saver, utility and I put them to sleep, he always make a stop down.

  How do I restore that?

  Hello!

  Have you downloaded the BIOS for Windows XP?
  For the Satellite A200, there are two versions available; one for XP and one for Vista.

  Also, make sure that you have the latest graphics card driver and keep your XP to date.

  Good bye

• Satellite Pro L10 begins to if auto close the lid

  I've got a L10 running windows xp profesional. The problem I have is after the laptop is off and I'm going to close the laptop top restarts.

  Hello

  What?
  Are your sure that you do not use the option "restart" your laptop?
  The Windows operating system contains the closing down, and then restart the option.

  The other possibility is that the parameters energy saver is defined to start the laptop.
  Please open the energy saver and check the option "when I close the lid.
  But it's very strange because you can configure this option only in sleep or Hibernate mode.
  However I recommend you this feature and if necessary set it to no action

• Satellite C650 stops when I close the lid

  I recently got my laptop for Christmas, and a few weeks ago, I noticed that whenever I opened the cover, I had to turn it back on. He woul say the computer stops unexpectedly. Then you choose the security mode or regular. You hit one and we would send you to the Start Up repair.

  What should I do to get that normal back where I can close the lid and then open it again without having to reboot and wait more than seven minutes to start repair.
  Also, I got the blue screen.

  Do I have a virus, or is there another way I could fix it?

  Stand by. In the history I n t understand one thing: in power options on the side left (blue color), you can find the option choose closing the cover. Which option is implemented here?

  What should your laptop when you close the lid?

• Satellite L500 - external screen display after closing the lid?

  Hello
  I use the Satellite L500 - 120 Notebook, and before installing Windows 7, the laptop has a function very uncomfortable, when I applied an external display.
  When I closed the lid of my laptop, Office was shown on my display (with the native resolution of the external display) external, so I had not to
  change anything on the control panel. In Windows 7, Miss me this feature. I already tried to use the Control Panel, but there is no parameters, which fits
  with the previous ones. I can duplicate the screen in order to see my desktop screen on my external screen, but with the resolution of 1366 x 768 laptop.
  If I extend the views, then there is only the background image to the external screen, but this time with the native resolution.

  So my question is, how to conifgure Windows to recognize that I closed the lid, and the screen should be shown on my external screen?
  Or should I install applications Toshiba, that I had before, who visited account this function?

  Thanks for any help!

  Hello

  I m not a Windows 7 user because I want to wait until it will be released official, but I hope that I can help you a bit:

  First of all in power management, you can choose the action that happens if you close the lid (g. e. sleep, close, etc.). This action must be disabled because otherwise the laptop shuts down or something else.

  So I think that you need to install the display driver for your laptop. You can try the Vista driver because most of them are working on Windows 7.
  Then you should be able to define the correct screen resolution for external monitor.

  A working display driver is important to the clone or extends monitors to verify this!

• Satellite L300-1FS - Wireless reconnect after closing the lid

  Hello

  My 2 month old son Toshiba laptop works very well in many ways, but an annoying problem, is that if we close the lid when you open it again it doesn't re connect to our router. If I click on the network connection, it just says: there is no everything!

  Sometimes the switching market re wireless switch will connect there, but more often than not, it's a reboot, which is annoying.

  Proves that the wireless card works but it would be nice to not have him harass me every time it does not connect.

  All ideas welcome.

  Hello

  First a question: what exactly happens if you close the lid?
  This laptop stops, or goes to stand-by or extended sleep?

  However, in your case, I would try to update the driver WLAN and the BIOS. Check the Toshiba website for updates:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  It would be interesting to know what operating system you have and if you are running the factory settings or you have installed another OS?

  A friend told Satellite L300 and he is very satisfied and can t notice any problem. :)

• Satellite U300 will switch to standby when the lid is closed during shutdown

  My U300 is set to go in mode 'sleep' whenever I close the lid, as most of the laptops I use. But when I shut down this computer and close the lid, it goes to sleep Mid-stop!

  This means that when I want to stop, I have to wait until it finishes and then when I open it again I have to wait until it stops and starts then, often to see that the battery is almost dead too! Any fix for that?

  Hello

  To be honest, I don't see any problem there. The same thing happen on my Satellite P200 preinstalled Vista. The process of closing time and if you interrupt close laptop screen, it makes sense that, after you open the Vista will continue stop procedure.

  For you, it will be better to make the best configuration of the laptop. Just for example:
  -If you want to switch to sleep mode use FN + F3 key combination. After a few seconds, the laptop will be in standby mode and you can close the lid
  -Use the power option and choose the option STOP for when I close the lid

  On this way, you will have perfectly configured OS for your needs and no problem more. I use the same configuration.

• Computer stops whenever I close the lid

  I have a 5510 accuracy is around the age of 2 months with 10 Windows installed on it.  In 2-3 weeks he started close subject when I close the lid.  Of course, I never close the lid and save open it immediately, it's usually hours later or the next day.

  My settings specify that when I close the lid it falls asleep on the two battery and plugged in, but now it's apparently close because when I re - open the cover later it's start.

  I saw another post that mentions trying several things like updating video drivers or do some diagnostics on the hard drive.  What should I check first?

  Hi KLIEMOHN,

  This happens with or without the adapter plugged? Is there the bluescreens / system breaks down? The pilot light and manual standby modes work fine? The system into hibernation and turn very well?

  Update the BIOS - http://dell.to/1U2Js3b

  Create a system restore point.

  Reinstall the chipset and video drivers from the same site above.

  Go to control panel-> options-> to modify the parameters of plan-> change advanced power-> sub sleep settings - disable hybrid sleep - under the power buttons and lid-> check lid close action settings - apply and ok

  Restart the system and check that it works very well.

  Create a new account admin and check - http://bit.ly/1JoFhcw

  If the problem is not resolved, restart the system and press f2 to enter the BIOS - close the lid and open again and check if the system stops, and it stays on in BIOS mode.

  Restart button f12 system and press on start - choose the diagnosis. Let run diagnostic tests and if you encounter errors - take note of the full error even report for us.

  If the system is under warranty, write me a private conversation with the service tag, your name and e-mail address.

  Keep us updated.