Satellite A300 does not start after the installation of the anti-virus

Similar Questions

• Satellite M200 does not start after the RAM 4 GB upgrade

  Hello

  I recently updated my RAM just to speed things up a bit as RAM is so cheap these days.
  I have a MEAC M200 T2130 Vista with 1 GB sticks (2 * 512).

  The new sticks are 2 * 2 GB Dane - elec DDR2 pc2-5300, when I put the two and restarted the hard drive light came briefly and then it is just options BIOS of Idol, no POST.

  I tried to use a single stick of 512 MB with two new sticks and they both work in a 2.5 GB configuration just not together that also this only works when the stick of 512 is in internal housing and not vice versa.

  So if someone has had a similar prob or can give me some advice that would be great, I'm not sure if the motherboard can support 4 GB?
  Thank you, Dave.

  Hello

  There are two possibilities why your M200 doesn't not start after upgrading RAM.
  First the RAM installed may be not compatible or could be faulty or the computer laptop doesn't support 4 GB of RAM.

  I put t know what M200 do you have exactly, but you can check the installed chipset and could check on the Intel page if this chipset would support 4 GB of RAM.

  Welcome them

• Satellite A300 does not start after extinction during the BIOS update

  Hello

  I tried to update the BIOS after reading a TOSHIBA TEMPRO alert, after some time, apparently not run so I ran a second time, then both ask of BIOS appeared in the taskbar only and it froze while I did not start the upgrade or anything like that I had to the power off.

  I tried to restart, but now, it just on the screen stays black (the monitor is not powered, as if the system was not running), all LEDS are powered with flashing 'drive access', the led on the DVD Player keeps flashing making a noise every 3 seconds or more.

  I read on the forum that there may be no solution but to take it to an authorized service provider but I'm willing to take any possible solution before you do.

  Thanks for any advice.

  Alex.

  Hi, mate

  Unfortunately, you need to be reflash the Bios as something that went wrong during the update. You should contact the Asp and ask them to reflash. There is no other way to get your laptop to work.

  Good luck!

• Satellite A30 - does not start after the RAM to level

  Hello

  I recently installed a crucial for memory
  my laptop, which is a Toshiba Satellite A30. However, when I try and
  restart the laptop, he tries to restart the fan turns on then turns off with a beep sound and this is not
  even to get to the Toshiba start screen.

  The memory I installed is 1 GB, 200-pin SO-DIMM, 128 X 64, DDR 333, CL2.5, part number CT12864X335.

  "Memory module PC2700 DDR 1 GB, 200-pin SODIMM

  CT12864X335
  
  
  * Size of the module: * 1 GB
  * Package: * 200-pin SODIMM
  * Function: * DDR PC2700
  ' * Features: * DDR PC2700 • CL = 2.5 • unbuffered • NON-ECC DDR333 2.5V • • • 128Meg x 64 •.

  I have
  took out and put back the old memory and the laptop boots
  normally and is OK, I even tried to put the memory in different
  slot machines, but it still has the same problem.

  This suggests that memory is faulty, as bought crucial memory must be compatible with my laptop?

  Thanks for your time,

  You have this problem if you use modules or only the new module?

  If you only use the new module, the case is clear. The new module is defective or is not compatible with the laptop.
  I think you should get back on the computer dealer and request a new. Maybe you can get a Kingston module because I have only good experience with this production.

  If you use both modules, they are not compatible. You should only use the modules with the same specifications.

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Satellite L350 - does not start after the BIOS update

  Hello

  I recently (yesterday) downloaded the latest version of bios update dated dated 25/02/10 2: 20 - WIN, after download and does run the software from the laptop immediately stopped working and stop. I am now no longer able to boot up the laptop at all, all I get is the power light on and the hard disk light flashes, I hear the spinning CD/DVD drive, but what is not screen anything, I don't think this is the start.

  Is there a way to fix this without taking it to a store/engineer, BIOS recovery?

  The laptop is a Satellite L350, I opened the laptop to try to reset the CMOS by removing the card mother battery (not sure if it would have helped), but as much as I know it doesn't have an or I'm not.

  Any help would be greatly appreciated.

  Thank you

  Andy

  Hi Andy,.

  Hmm... If the BIOS update failed, you can't do anything because only an authorized service provider has professional diagnostic and recovery tools to redo an update.

  So in my opinion, you must contact a service provider authorized in your country. Get in touch with the guy and ask for help. They will tell you what to do now.

  Here is their list:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  Good luck! :)

• Satellite L30 does not start after the upgrade to 2 GB of memory

  I bought 2 GB Crucial memory for my L30. After removing the 512 MB module and adding two modules of 1 GB the L30 wouldn't start. With only 1 GB start ok ok, with the other boot only 1 GB.

  Either 1 GB modules and module of 512 MB with start ok. The two modules of 1 GB boot not together. Crucial gave up and offered a full refund, but I'd rather have a solution if possible.

  At the BIOS level is 2V30, that I understand to be the latest version available.

  Ideas please, John

  Hello

  You're right, this problem seems very strange and I wonder why this happens.
  Satellite L30 certainly supports the 2 GB of memory and you should be able to upgrade with 2 x 1024Mo modules!

  It's strange, but it seems that these two modules are not compatible together
  I found Toshiba recommend module on options and accessories site.
  DDR2 400/533 1 GB (PA3411U-1M1G) maybe you could try this one...

  In any case, I don't think that you will be able to solve this problem in another way. The modules must be replaced.

• Satellite L30 does not start after the BIOS update

  Hello

  I upgraded my BIOS Satellite L30 and now the laptop will not boot. When I turn on the fan starts and that's it. I think I have updated the book with the bad BIOS... The laptop is only 1 day old... Is it possible to reset the machine to the default BIOS.

  Help, please...

  Hi Scott,.

  Unfortunately there is no easy way for you to go to your BIOS to its previous level. You need to entrust your laptop to a Service approved partner who has the necessary equipment to Flash the BIOS to the previous level.

  Kind regards

• Satellite L855 does not start after the BIOS update

  I downloaded the BIOS update and followed the instructions there during the installation, but on reboot (including the requested configuration), I get a blank screen. Intermittently, the CPU fan starts and stops. I think that the BIOS update failed, how to solve this problem?

  Thank you
  Neil.

  Hello, Neil

  In General when the BIOS is screwed up you need professional help and you should contact the nearest Toshiba service provider and ask for help.

  See also this thread. Perhaps this methid can help you too.

• Satellite A100 does not start after the wrong Bios Update

  Yesterday, I upgraded my BIOS of 1.90 to 2.20 for VISTA... now, apparently, I downloaded the BIOS bad a100 to my A100 (PAAS...)

  Now the computer turn on (no display) then a few seconds later stops offshore and turns on again (without interruption), I am under warranty (and the computer is in the store) but I was wondering what to do if Toshiba is not honor the warranty?

  Thank you very much for your help!

  Hello

  I'm sorry to say, but it seems that you don't have the choice.
  You can ask him authorized partner in your country for the help that I know, BIOS update errors are not covered by a warranty and you will have to pay a small fee for fixing.

  In the worst cases, the motherboard must be replaced:(mais peut-être avez_vous une évasion chanceuse et seulement la puce ROM doit être flashée à nouveau)

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Z600: computer does not start after the installation of the 5 TB SATA drive

  My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

  Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• computer does not start after the installation of vista updates.

  computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

  Hello

  Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

  Hope that information was useful

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.