Satellite A300D-11 t - can not get external Wlan Realtek 8187b at work

Similar Questions

• Equium A300D - 13 X can not get any sound using Win7 32 bit

  Hello

  ive installed win 7 home premium 32 bit but can't get any sound.
  I downloaded the drivers available here but still no joy?

  I then started to vista only to find yet, I couldn't get all of her even if the drivers installed etc...
  Also read here that it's realtek hardware so I downloaded drivers off there website but still no joy.

  Any help would be appreiciated

  Thank you

  Hi mate

  You installed a wrong driver sound!
  The laptop supports the audio chip Conexant CX20561! It s NOT Realtek but Conexant!

  You must use the Conexant audio driver

  Please see the page of the European driver Toshiba again! The satellite * A300D box contains the correct Conexant audio driver!

  Welcome them

• Re: Satellite A300D - Bluetooth Stack can not find a service

  Hello!
  I have the Satellite A300D with Windows 7 and battery Bluetooth Toshiba (ver. 7.00.10)
  I want to connect my mobile phone to laptop via bluetooth. I tried to add a new connection in the Bluetooth stack. BS found my phone, but cannot connect to. BS showed an error message 'Cannot find a service' (I have a Russian version of Bluetooth Stack, so I have to translate the message). And I don't know what service is not running, BS don't give any additional information.

  Please, advise me what can I do to solve my problem.

  I think you must turn on the bluetooth feature in Administrative Tools-Services:

  http://img42.imageshack.us/img42/3384/blie.jpg

• Can not get my portable floppy drive to work on my computer

  Original title: I have a portable floppy drive that works on all computers but mine! It indicates that the device is installed and ready to use, but when I put in a disc, nothing happens. What can I do?

  It was in the shop and they said it worked fine in my computer to the shop. But at home, nothing. I tried on my old Mac and it works, too, but not on my PC.

  Hi Barrydraw1,

  ·         What operating system is installed on your computer?

  ·         What is the brand and model of the computer?

  ·         The floppy drive is not detected by the computer?

  ·         Have you tried to insert a different floppy disk and check?

  If the drift of floppy is not getting recognized by the computer, and then run the Fixit and check.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  If your computer does not support floppy drive so it will not work.

  I hope this helps.

• Can not get the XML save data to work

  I'm trying to store data in an XML file.

  I want to create and store this XML file, I copied this example directly from the documentation (http://developer.blackberry.com/cascades/documentation/device_platform/data_access/working_with_xml... but it does not work):

  // Create QVariantMap objects to contain the data for each employee
          QVariantMap firstEmployee;
  
          // Populate each object with data
          firstEmployee["firstName"] = QVariant("Mike");
          firstEmployee["lastName"] = QVariant("Chepesky");
          firstEmployee["number"] = QVariant("51649875");
  
          // Add each employee to a QVariantList
          QVariantList myEmployeeList = QVariantList() << QVariant(firstEmployee);
  
          // Add the employee list to a top-level QVariantMap, then wrap it in a QVariant
          QVariantMap topLevelEmployeeMap;
          topLevelEmployeeMap[".root"] = QVariant("employees");
          topLevelEmployeeMap["employee"] = QVariant(myEmployeeList);
          QVariant myData = QVariant(topLevelEmployeeMap);
  
          // Retrieve the working directory, and create a temporary .xml file in that
          // location
          QDir home = QDir::home();
          QTemporaryFile file2(home.absoluteFilePath("myXMLFile.xml"));
          qDebug() << "Came here";
          qDebug() << home.absoluteFilePath("myXMLFile.xml");
          // Open the file that was created
          if (file2.open()) {
              // Create an XmlDataAccess object and save the data to the file
              qDebug() << "I came in this if statement";
              XmlDataAccess xda;
              xda.save(myData, &file2);
          }
          else
              qDebug() << "I didn't come in this if statement";
  

  After having tried everything, I can't see the .xml file to display in the file Explorer. The print statement that prints the location... /data/ and the second print statement shows he's going in the case.

  I can not even an XML base to save, so I wonder if I'm doing something wrong.

  Thank you

  Hey there,

  Well, the thing is that she is using an object QTemporaryFile (file2) and according to the description of the class QTemporaryFile:

  ".... QTemporaryFile is used to create unique temporary files safely. The file itself is created by calling ( Open). The temporary file name is guaranteed to be unique (that is, you are guaranteed to not overwrite an existing file), and the file will be deleted eventually to the destruction of the object QTemporaryFile... »

  If the object of File2 is destroyed in your application, that would be your problem...  You check in the file while the application is running?  Otherwise, you must use QFile instead so that the file will still be there at the end of your app... etc. etc.

  https://developer.BlackBerry.com/Cascades/reference/QFile.html

• Can not get the States of relaxation for work in the widget of blank publication of Muse

  Hello

  I don't know what I'm doing wrong, but I cannot get States to trigger (thumbnail) to work in the blank publication. That's what I do:

  I click on one of the triggers (thumbnails), open the States Panel, select the Normal State and fill the tile bearing the image of the . Then I select the rollover State and reduce the opacity to 50% or make any other changes to this State. I see [in the States Panel, in design mode] now in the States Panel which show both normal and Active image with an opacity of 100% and turnover and the mouse down show with an opacity of 50%. BUT when I preview the page in the browser, move the pointer of the mouse on the trigger does not change state of the thumbnail. It does not raise the change of the target, but the thumbnail itself doesn't change States. The idea is that when I mouse over the thumbnail, an image appears in the target box. But I also want the thumbnail to change status while in the rollover State. I have attached a screenshot of the Options Panel in case it helps.

  Any help with this will be greatly appreciated!

  Tania

  

  Depending on your options settings of Composition, changing the active State to the same settings as your rollover State. When you hover over the trigger will change and show the target.

• BlackBerry smartphones can not get a stereo Bluetooth headset to work with Pandora

  I have a BB Storm 9530:

  Is it possible to get a stereo Bluetooth headset to work with Pandora?  Or it only works with the 3.5 mm headphone and internal speaker?

  I use my headset for Moto Rokr BT very well with Pandora. While the music is playing, try to hit the button options and see if you get an option to transfer to Bluetooth

• Broken LCD - can not get external display

  My screen is no longer good so im trying to connect an external display.

  Been trying for hours to try to get the external display to work to boot.

  Ive tried 2 sets of hd and svga cables change everything. The function key.

  The laptop does not recognize the display, but seems to go in something or powersave mode.

  The only way I can get the external display to work is if I remove the battery and wait a bit and then power

  the display works with a notice on the screen that the cmos will reset to default settings then restarts

  and back to where I was once again... IM thinking that it something in the bios that is the cause.

  I thank you and hope I can understand this.

  Pavilion dm4-1160us

  HI Ezfilez,

  I understand that you have a problem with the external screen on your Windows 7 computer.

  Sometimes it is in the BIOS. If you follow the link and update, that it should help solve your problem.

  http://support.HP.com/us-en/document/bph07110

  Please let me know if you need assistance.

  Thank you

• Satellite A100-062 psaane: can not get the card reader to work

  Hiya... Please can someone help?

  I try to use my card reader with a Pro duo stick.
  I put it in the Pro duo adapter and when I put the card in the slot of the card reader that nothing happens...

  Thank you in advance if you can help.

  cordially imalive

  I use the memory stick duo adapter and when I on it on the inside of my Satellite in Windows Explorer is happening again drive (F) and symbol that shows Memory Stick.

  Try to please several times to put inside. I remember that in my case it worked after the third time I put it in the slot.

• Satellite Pro A200 PSAE1E: Can't get the shortcut keys don't work on Win XP

  Hello

  I have a Satellite Pro A200 PSAE1E that came with Vista on it, I reinstalled Win XP Pro installed with relevant drivers download Toshiba page but cannot get working shortcut keys.

  I installed the controls and the driver, but that doesn't seem to work. Saw an ad on "common module" somewhere, but can't seem to find any links to download on the download page.

  Can anyone help?

  Thank you very much

  Iain

  The control utility and driver controls allow you to customize and TOSHIBA special button preset settings. But it is not a FN keys!

  You must install the Hotkey utility if you want to use the FN keys.

  Another tip:
  It is important that all Toshiba drivers and utilities are installed in the correct order.
  On the Toshiba driver page, you will find a txt file called installation instructions.
  Please install all drivers and tools in the order mentioned in this instruction!

  Greetings

• can not get the new hard drive to work in the Pavilion ze4805us laptop

  have an HP pavilion ze4805us laptop which had a total hard drive failure... recovery disks were lost in a fire... replaced the hard drive with a Western Digital 250 GB drive... computer recognizes the drive, but with only 137 GB... impossible to obtain the Windows Millennium disk to install... I have it get the PXE - E61 error code... have looked for answers and tried a few suggestions to fix the error code, but no luck so far... would like to throw this laptop and runs again, it was so nice all in operation. Can someone help me with this? Thanks to all in advance... rrcar6

  At the level of the BIOS, HARD drive should show the full capacity regardless of the distribution, but it will be limited based on what the current logical block installed the BIOS supports.  For example, the 250 GB HDD Needs LBA 48 bit to be recognized by the BIOS in its entirety.  Western Digital only provides downloads of software and support going back to Windows XP.  Windows Millennium Edition is not able to recognize the full capacity of the drive.  Finding drivers compatible with Windows ME is perhaps another challenge that XP uses a different architecture than Windows ME done.

  It seems that this laptop is the same time that the books mentioned in this thread.  Response from JackShack gives the best explanation as to why he shows quite different in the BIOS.  It has been many years, but I do not remember that the capacity of the HARD disk had exceeded what the BIOS at the time supported resulting in the 137 GB limit displayed in the BIOS.  This section of Western Digital shows that this problem is related to the operating system or BIOS supporting however, this should not prevent Windows to install correctly.

  I'm sure it's already done, as it was not a new BIOS since 2004, but guarantee the newest BIOS is installed.  Logical block address 48 bits, necessary for the larger disks (larger for the time) was released in 2003.  The 2004 related BIOS earlier than probably took supported LBA.  What is the current version of BIOS?

  What is the exact message that you get when you try to install Windows Millennium Edition?

• Can not get printer hp psc 750 to work with a new Dell dimension 8300

  Original title: the printer does not work

  I have a new Dell dimension 8300.  My printer is a former hp psc 750 printer scanner copier I can't print.  Can anyone help?

  Hello

  You should ask in the Forums of Windows answers corresponding to your version of Windows.

  Windows answers forums
  http://answers.Microsoft.com/en-us/Windows

  --------------------

  Check with HP Support, their drivers and documentation online and ask the HP
  forums for known problems.

  HP PSC 750 printer
  http://h10025.www1.HP.com/ewfrf/wc/product?cc=us&LC=en&DLC=en&product=57769

  Drivers HP PSC 750
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?LC=en&DLC=en&cc=us&product=57769&

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ------------------------------

  It might be a problem with the computer as an OEM Dell provides support
  for Windows.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.

• Can not get the graphic import settings to work

  Hello

  I try to import a graphic by reference to a set DPI (222). The following code example graphic design is important, but don't know the DPI setting. You can see what the problem is? A few notes:

  -J' wrote an equivalent FDK and everything worked well, the same exact way.

  -The GetImportDefaultParams() fills a table of about 45 members and GetPropIndex() retrieves the unique index, which suggests that the parties are working

  -After experimentation, I conclude that parms [index]. PropIdent is still not defined, that seems odd.

  Thank you.

  var doc is app. ActiveDoc;

  var tl = new TextLoc();

  TL.obj = doc. FirstSelectedGraphicInDoc;

  If (!) TL.obj.ObjectValid) tl.obj is doc. MainFlowInDoc.FirstTextFrameInFlow.FirstPgf;

  TL.offset = 0;

  var parms = GetImportDefaultParams();

  index = GetPropIndex (parms, Constants.FS_GraphicDpi);

  parms [index]. TypedVal = 222;

  index = GetPropIndex (parms, Constants.FS_FitGraphicInSelectedRect);

  parms [index]. TypedVal = false;

  var returnParms = new PropVals();

  doc. Import (tl, "C:\\temp\\delete\\222_dpi.jpg", parms, returnParms);

  Hi Russ,

  What exactly is your problem, I don't think that its really the value NULL of PropIdent?

  So I guess that your problem is, dpi is not defined.

  If I change one of them * DefaultParams(), I use this function:

  function SetPropVal (prop, propval, params)

  {

  var i = GetPropIndex (params, prop);

  If (i<>

  Returns false;

  If (typeof (propval) is 'number')

  params [i].propVal.ival = propval;

  If (typeof (propval) is 'chain')

  params [i].propVal.sval = propval;

  Returns true;

  }

  First parameter is the value of constant, the second the value to set, and the third the * DefaultParams.

  Hope this helps

  Markus

• Can not get my PHP test email to work

  
  

  Hello

  I'm trying to set up a form for my site, I go to http://www.mindpalette.com/scripts/index.php#NMAnchor to help me, I want page of thanks returned to use with the news of the form sent to my email address. Download instructions above gives me a test PHP page (placed in my root folder Local and found on browser) the test page asking me to enter my email address in and send. But I can't retrieve e-mail. I have improved my IP web pagage so that it accepts script. But still no luck. Too tired by sending other e-mail addresses. Was told that there may be a problem with my out going email account. All my accounts run from Mac mail.

  Don't know where to go from here.

  LouisaBoyles wrote:

  Hello

  Yes, I tried everything and double checked. I tried first with mail from Nate. Now to process the form.

  Attached the pic mode code & form in dreamweaver. Also one of my remote files, which clearly states that ProcessForm.php is here.

  My action of forms in the property inspector is ProcessForm.php

  My link is http://www.denotestationery.com/form.html

  Your form action field is just "form.php" (see below)

  
  
  Unless you have renamed the file you downloaded from Mind Palette itshould be ProcessForm.php
  
  ????????????
  
  At the moment when you click the forms submit button its looking for a file named
  
  'form.php' on your server and its not finding it.
  
  That could be because you haven't uploaded it or there is no such file on your
  
  server with that name. 
  
  
  

• Can not get the Google domain name to work with Adobe-accommodation

  Hello world

  First of all - I am a novice in that kind of stuff so any help is much appreciated, while I watch through this. I am the owner of my domain through Google domains and I try to the host through the Adobe Business Catalyst with my custom domain name: outercoastseafood.com. I changed what I thought was the correct DNS settings in Google, but after waiting 48 hours there is still nothing available. Google settings are:

  

  I also have a Microsoft email account that uses this field which seems to work fine. I looked at the field on intoDNS and got these results: http://www.intodns.com/outercoastseafood.com

  Any help or ideas are appreciated!

  Thank you
  Erik

  Hello

  Please remove 1st two records and leave ns1, ns2 and ns3, wait a few hours and it should be good.

  unless this is done, use the url to access the site

  http://outercoastseafood.BusinessCatalyst.com/Admin/index.aspx

  Let me know if you have any question.