Satellite A300D-135 - BIOS - System Configuration data read error

Similar Questions

• Satellite P200 Vista Ultimate - boot configuration data read error

  I have a Toshiba Satellite P200 running Vista Ultimate.

  Recently I started having a problem after restarting after the installation of vista updates. In fact, it will not start at all and gives me the following message on a black screen.

  Windows could not start. A recent change in hardware or software can cause of bethe. To solve the problem:

  1. Insert your windows installation disc, and then restart your computer
  2. choose your language settings, and then click Next.
  3. click on "repair your computer".

  If you do not have this disc contact your manufacturer aministrator or the computer of the help system.

  File: \Boot\BCD

  Status: 0xc00014c

  Info: An error occurred trying to read the boot configuration data.

  The only way I can fix it to insert the recovery dvd and click on repair. This levonorgestrol only when the computer restarts after an update. If I manually turn off the computer, then on start up fine.

  I don't want to put automatic offf to update more because I think they are important from the safety point of view, however, this situation is not acceptable.

  Can someone please help.
  I have a screenshot of the error, but have reproduced the information above.

  Hello

  In my opinion, there is something wrong with your mater boot (MBR) of the drive and therefore the bootloader causes an error.

  Usually, you might be able to fix it using the original disk of Vista but it s really strange that this problem still occurs after the update to vista.

  In my eyes, you should really check if the same problem would happen using the Toshiba factory settings and configuration.

  Good luck

• Computer laptop Gateway does not load windows Vista, reads configuration data read error: System.

  OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
  4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:

  9D.03 BIOS version

  632K RAM passed system
  3966M extended RAM passed
  1024 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
  Fixed disk 0: WDC WD2500BEVS-26VATO
  Initialized the mouse
  Updated System Configuration data
  ERROR
  System Configuration data read error.

  I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).

  If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.

  At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!

• Equium A300D - 13 X - Configration system data read error

  Hello

  I have a problem with my Equium A300D - 13 X laptop, everytime I turn on my laptop it starts and loads the initial startup screen as usual, Toshiba once asked that loud "BEEP" comes from my laptop, and lists the following information:

  Phoenix TrustredCore (tm) NB
  Copyright 1985-2006 Phoenix Technologies Ltd.
  All rights reserved

  Herring of the ITA (DDR2 + T/RS690M/SB600)
  CPU speed = 2000 MHz

  639K system spent RAM
  1918M extended RAM passed
  1024 KB of L2 Cache
  Occult system BIOS
  Video BIOS with a shadow
  ATAPI CD-ROM: MAST * ADVD-RAM UJ-850 S
  Fixed disk 0: WDC W2500BEVT-00SCSTO
  Fixed disk 1: Hitachi HTS542520K9SA00
  Initialized the mouse
  ERROR
  System Configuration data read error

  Press to resume, installation

  I replaced the hard drive and flashed the BIOS settings as advised by Toshiba Helpline but the problem persists.

  Help, please! because the "BEEP" is now getting on my nerves!

  See you soon

  Hi andrew_net82,

  It seems that the BIOS has detected an error with a certain part of material...

  Before doing something I recommend you load the default settings in the BIOS. If you are in the BIOS Setup, press the F9 key.

  If it doesn t work you need for professional assistance from an authorized service I think. Guys need to check which part of the material is defective and must be replaced.
  List of the ASP, you can find on the official website of Toshiba.

• Read error - SOLUTION system configuration data

  Today, I found a solution to the error of notorious boot not only on the toshiba, but some other brands also.

  The error is: System configuration data read error.
  He invites to start with 2 beeps which prevents the computer laptop Moldavian from.

  I tried everything I could to remve this message but noything helped me.
  Replace all, cmos battery, updated the bios, loader, drives, keyboard and etc.

  Today, I found a solution very simple that I want to share with you guys.
  This solution worked for me and I hope it will work for you too.

  Are you ready? :)

  Go to the Bios and change the Bios language french.

  Post here if it works for you also.

  Thanks for sharing your experience with us. But its really hard to believe that your solution would be linked to all devices such problem

  However, good to know that this small change in the BIOS has helped you to resolve the issue

• Satellite A300D (PSAKCE) - BIOS is damaged and does not start

  I formatted computer after when I put update computer BIOS is frozen and it does not work now. File is true where I download from Toshiba Web site.
  I searched Web of Toshiba sites there was not any producere for recovery of the BIOS for the damged BIOS file. Many start-up models with some keys to the BIOS update but mine is not starting any screen only empty key.

  -Can I do it myself? Is there a procedure for Satellite A300D-17F (psakce)? I don't want to wait for the rear service it 6 months before I bought it.
  -If I send to the service, it is under warranty? I don't know any time service can be a problem. They say problem user but I reformatted the PC after I started the update program and they can not understant that sometimes.

  Thank you...

  Hello!

  In this case, you need help from the ASP. You can do anything and it is possible that the ASP BIOS reset.

  On the Toshiba site, you can search an ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good bye

• How reset/format of Toshiba Satellite A300D-135?

  Hello

  2 months ago I bought a Toshiba + Satellite laptop A300d-135 +. I want to totally
  format my laptop, because hes very slow and I don't know the reason. I also do not have
  got a cd that came with my laptop.

  I tried so many things to speed up my laptop, but nothing worked.
  I hope you can help me to totally discount to zero/format my laptop

  Yours,

  * Mustafa *.

  Hello Mustafa

  The recovery DVDs is not delivered separately and you must create only using the Toshiba Recovery creator utility.
  Please do it at first and later, we can discuss on the format of HARD drive.

  By the way: that have you ever tried making your computer faster?

• Satellite A300D - 156 BIOS update failed - I need assistance with recovery

  Hello

  I know it is old enough, but until now, it was just good enough for my use.
  In any case, after I did a restore of the Windows Vista operating system came with my computer, I got a notification of one of the tools of Toshiba that an updated BIOS is available for my computer.
  I downloaded and tried to perform an update. After that the process had finished (probably), the computer has not responded to the pad touchscreen and keyboard. I was not sure if the update really took place, especially because it looked like the computer has been is frozen. So I left it for the next +/-30 minutes, but no change.
  So I decided to reset it as even the power button did not work. So I had to remove the battery and unplug the AC power.

  ... and the computer has (almost) dead then.

  Now, it is that when I press the power button it seems to power up but the screen remains blank, fan works and Windows is not booting. It's just a short scratching sound of the DVD drive noise, and that's all.

  My question is, what is the recovery procedure in my situation? I tried to look for potential assistance on the Internet and I found a few forum or articles messages indicating that there is some recovery for the different BIOS procedures, but what is the procedure for my BIOS? The only thing I found the 'work' was that if I press the power button now the keys Fn + Esc, computer laptop powers on with power button / stop flashes. But how to force recovery BIOS flashing procedure?

  Thanks in advance for any help!

  It's really stupid situation now. You will not be able to fix it with a simple recovery operation. BIOS is broken.
  In the past I have faced no such situation but on this forum I found a very interesting thread on BIOS recovery. Please take some time and visit this thread.

  Maybe this will help you with your machine.

• Impossible to update BIOS for Satellite M40 - 135 - bios is not ACPI

  I had problems with the upgrade of the Bios on my laptop.
  I can't install windows xp before JC.
  I got BSOD "the BIOS in this system is not fully ACPI-compatible.

  Yes, I tried F7 and nothing helped! The bios only I found here is 1, 70 - WIN and that only works on windows. So I can't install also what I did I install windows 98 on it and my system is in place but I tried to install the Bios, I got error. So I can't start it to update.

  On this forum I saw it there has updated trad 1.70 if toshiba support team can send it to me on the email address so I could update the bios my bios is 1.0!

  Thanks in advance for any help!

  Hello

  First team Toshiba is not here in the forum user to.
  Secondly it can update BIOS victory only running Windows OS-based, it would be best that the use of the Toshiba preinstalled version of Windows in order to run the BIOS update.

  By the way; I found versions of BIOS Toshiba U.S. on page here, you can download the traditional BIOS which can be updated using the diskette.
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp
  Notes; Toshiba laptops, US have different model numbers.

• Re: Satellite A300D-15B - BIOS update failed and now I get a black screen

  I've updated my laptop to run windows 7 instead of vista some time ago and my laptop was running, but the fan seems to stop working and I found that a BIOS update can fix this on this forum. The BIOS update has stopped responding partially through and I had to shut it down. I tried to run again, but he continued to come up with an error message. The laptop was working fine, but once I turned it on the next day I found that it is only responsible to a black screen. My laptop is out of warranty, but I thought I would send it out the hope for a decent price, but she came back with a cost of mounting A £400 for a replacement motherboard and price tag. Anyone know if these types of problems can be repaired without full replacement necessary?

  Thanks to advanced to someone who can help :)

  Hello

  You must contact an authorized in this case service provider. You should speak with the technicians because they try to reflash the ROM module where the BIOS is stored. This isn't expensive and it s worth a try! ;)

  You can find a list of the ASP s here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  But in the worst case you need a new card of mother, but technicians must try to reflash the ROM module first

• Satellite A300D-17F - time system

  Each time time 30 s back

  I put t know what OS do you use but in Windows XP, you can synchronize the time with the internet.
  Double click on the clock, choose internet time and set a mark on automatically synchronize with a time server Internet.

  As far as I know that it is also possible in Windows Vista.

• Satellite L770D-10J wouldn't boot - Disk Read Error

  Hello

  My laptop cannot start and it gives me the Error Message:
  Error reading a disc like the case, press ctrl + alt + delete.

  I did it a couple of times and I tried to solve this problem because I have no Win7 DVD to boot from, I tried to reset the BIOS to its standard options and now he wants a password for me.

  I was not even enter a so I won't know it.
  After 3 attempts the system stops and I have to restart my computer.

  Now, I have an external hard drive but I can't try to boot from it because my laptop wants that password.

  To enter the BIOS or menu I also need this password.
  I really need help, if you know anything please contact me with 'NOTEBOOKS TOSHIBA computers SUPPORT. My warranty ran out already.

  Sorry for the bad English is not my mother tongue.
  Thank you for helping me.

  I assume you mean the BIOS password.

  This BIOS password can be deleted by authorized service provider available in your country.
  I have no idea why a BIOS password is displayed if you have not defined it in the past, but it is impossible to delete this unknown password by common laptop user. The BIOS password is a very important security element, and only authorized individuals are able to remove it.

  Also Toshiba information here:
  http://APS2.toshiba-tro.de/KB0/FAQ35002I000IR01.htm

  Error reading the disk:
  I'm not quite sure what disc do you mean exactly, but where the installed system cannot start, I think that the HARD drive is faulty and must be replaced. After this replacement, you will need to reinstall the system. The best way to install the system is using the Toshiba Recovery disk because all drivers and tools Toshiba would be installed with the Windows System.

• LV RT - system configuration: Find_Systems.vi - error "-2147220620."

  Hello

  I have problems with my code running on my cRIO in run as startup mode, but not in development mode. See extracts attached code. Copy the following code does throw some error when I run my development system, but when I deploy on the cRIO, my log file shows an error:

  -2147220620, source: nisyscfg.lvlib:Find Systems.vi:1750001
  «"" "String of full appeal:»»"»
  nisyscfg.lvlib:find Systems.vi:1750001

  I looked at the error and it corresponds to "a specified expert is not installed."

  I made sure the cRIO has every possible thing installed and up to date, if this isn't the problem. I also forced the nisyscfg.dll to be included in the support directory and the error persists.

  I ran the VI of Experts get so to get these:

  mcSysApi Motion system API Expert 14.0.0

  nor-1588 OR-1588 2008 1.0.3

  NEITHER nor-rio-RIO 14.0.1

  Neither visa NOR - VISA 14.0

  niimaqdx NI IMAQdx Sysapi Expert 1.0

  nisyscfg Configuration system OR 14.0.1

  nitsf NO time Sync Framework 14.0

  series NI - Serial 14.0

  XNET NOR-XNET 14.0

  It's the second time, I ran problems where there is a discontinuity between my code running on the cRIO only and it works in development mode.

  Does anyone have suggestions for this problem?

  Thank you

  I may be something, but I do not have 100% tested solution yet. If I run the VI once RT has had time to sit for a bit, it doesn't throw the error. This leads me to believe, the cRIO had not fully initialized at the time I called the VI. I think it is a bug on a part of NOR, because all the libraries, etc., must be charged at the time that runs the code in real-time...

  in any case, I made a loop trying over and over again (max 60 seconds) until no errors are oputput and it seems to work. It takes about 30 seconds (from cRIO startup) to error out not well.

  I have tested in my complete application now and will report back if all goes well.

  EDIT (follow-up): it worked! I guess that there is not much of a fix, but more than a workaround. It takes almost exactly 30000ms each time for no error.

  Best,

• NIScope data read error

  I'm trying to use the attached vi(been simplified) to get NI5133 data.

  But received error as the screen attached. I use niscope Panel before a certain time is ok, sometimes the name of the boot device is gray.

  The program works great on this laptop, even once today worked. But now cannot work after reboot several times.

  Any suggestion, thank you.

  Error 1074118647 occurred at niScope read WDT.vi:4

  Possible reasons:
  A previous acquisition is still ongoing. If you attempt to change an attribute, note that you cannot change the fetch attributes while an acquisition is still ongoing.

  Have you seen this?

• RS232 data read error

  Hello

  I use RS232 to get an OPTICA dew point sensor data. Whenever I run my program labview (attached file) it gives me the data but not the complete data. Sometimes, I'm a part of the data in call 1 and the rest of the data in 2 cal. Sometimes I don't have LMA data only once, and sometimes none at all. But when I run the program in EXECUTION mode to highlight I data in appropriate and complete order.

  Is there a problem with the labview program? or my instrument is not able to answer the call at the time!

  Any solution to this problem will be highly appreciated

  Thank you

  Ford

  My first guess is that you do not wait long enough for the instrument to respond. You have enabled endpoint character but then you make a VISA to the Serial Port bytes. Do one or the other.

  In addition, get rid of the structure of the sequence. It doesn't do anything.