Satellite A300D - unable to connect to the router

Similar Questions

• EA6500 unable to connect to the router after Time Machine

  Just got an EA6500 - updated to the latest firmware available.

  I have attached 2 x WD NAS and 1 x WD through the USB port of the device.

  Each time after I finished running Time Machine on the MacBookPro (written to one of the WD NAS), I can no more connection to the router as neither the local IP, or the cisco connect cloud. The error message I get (loosely formulated) is: unable to connect to the router. Please ensure that the router is connected to the internet.

  At this point, all the devices connected to the router (wired and wireless) still can access Internet perfectly. Only the console of the router is therefore more accessible.

  Anyone else have the issue?

  Any ideas on how to solve it?

  Contact support for Cisco and the person advised me to do a factory reset (even if the router is new with no customization!). Regardless, it now works correctly. Cisco Cloud Connect works always before, during, and after a Time Machine.

  "When in doubt, try to turn the grid and the.

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Unable to connect to the router WLan - Satellite L300D

  Please help me so that I have still a few hairs left!

  I installed WLAN driver on my laptop Satellite L300D with Vista Home installed.

  I see my network in the available connections, but when I go to connect, it will not connect.

  My other two desktop computers can connect to the router without a problem.

  Any suggestions?

  Thank you
  Neil

  Hello

  I think that you didn t try updates. Right?
  Therefore, my first recommendation would be an update of the BIOS and driver WLan.

  Check the current version of the BIOS that is available on your laptop. If the latest version has been released then update the BIOS.
  In addition, to download the latest WLan driver from the Toshiba WLan portal and to update:
  http://APS2.toshiba-tro.de/WLAN/

  On this Wlan site, you will find three different WLan drivers for three types of WLan cards. First check your wireless network card, and then use the right driver!

  See you soon

• Satellite L650 - unable to connect to the public network (has no valid IP address)

  Hello

  Toshiba satellite L650 laptop computer (with windows 7 64-bit), I bought two days back and I'm unable to connect to the public network. Sometimes, it must be connected to the public network and after a few minutes it disconnects. I get the message "wireless network doesn't have a valid IP configuration him."

  I have visited many forums and did everything, but of no use.

  1. people with disabilities the tcp/ip V6 of the registry.
  2. the DHCP is enabled. With the help of the automatic IP (DHCP)
  3. also tried with a static IP configuration.
  4. uninstalled the antivirus provided with laptop computer (Norton).
  5 disabled the windows firewall.
  6. restored to factory settings.

  I called Toshiba Tech support as well and they have suggested that it may be a problem of H/W but I don't think that so that it can be hardware problem because sometimes he must be connected to the public network. Now I'm left with no option except return the laptop to Toshiba (I'm less interested in this because I know that sending laptop for replacement will be more frustrating).

  Can someone please give some other suggestions for this problem?

  Hey,.

  Can you connect to your home WIFI router correctly?

  If you have problems with the public network connection, you should ask the owner of these networks. Usually, there is always a contact, you can ask if you have any problems with the connection.

  What you can try is updated WLAN driver from Toshiba's official website:
  http://APS2.toshiba-tro.de/WLAN/

  If it doesn't work, ask the person contact I mentioned.

• Satellite A500 - unable to connect to the WLan

  I'd like someone to help me.

  Have recently bought a satellite A500.
  I'm new in the world of laptops so I'm wrong.
  I connected to a router via a modem, the two netgear, the news.

  Had the two config for my network. Works well as long as ethernet is connected to the router of computer.

  My wireless icon on the front of the laptop is orange.
  If this should be green as the router?

  Pressing FN f8 it tell me wireless is connected.
  When I remove the ethernet cable it tell me to fix the problem, I need to plug in the ethernet cable.
  But I want to go wireless, I'm sure I'm missing something.

  Rang netgear but after that my router and it is not connected to wireless technology they could help me more.
  I use windows7.

  Thanks to anyone who can help me.

  > My wireless icon on the front of the laptop is orange.
  > Should it be green as the router?

  The WLan led can only be ON or OFF. If the light comes on (any color) then it means that the Wlan switch is on!

  It seems that the WiFi is enabled. In this case, you will need to properly configure the WiFi network.
  You can use the own WLan settings in Windows or a Wlan configuration tool like Intel ProSet utility.

  First need choose the right SSID (wireless network name), right of encryption (WEP, WPA, etc.) and password encryption.
  Please note that all of these parameters should be the same on the router WLan and WLan configuration software!

  Please check if the firewall does not affect the connection to the internet as well!

  PS: make sure you use the latest version of the WLan driver
  Here you can find the drivers:
  http://APS2.toshiba-tro.de/WLAN/

  In addition, search and read comments here on the forum!

• Unable to connect to the router

  -Please ignore this message: I did not wait enough to do the factory reset. It seems that launch a factory reset without waiting for 10 seconds only restarts the router.

  Hello

  Today I tried to connect to my router (I do not use it for a few years) and it didn't work at all.

  Initially, I plugged it in just 2 RJ45 cables: one for internet, one for the PC. The computer could not connect to the router (DHCP failed).

  I then restored the factory settings and tried again: same thing, the computer could not find the router via DHCP.

  I tried to force an IP address (IP: 192.168.1.5, mask: 255.255.255.0 Gateway: 192.168.1.1).

  By forcing the INVESTIGATION period, I was able to connect to the router, but when I tried connect to 192.168.1.1 with admin/password, it wouldn't let me (bad password - don't forget I restored it to factory settings, several times actually). The address http://routeurlogin.net/ is not found (404) and I was unable to go on websites (404). A curious thing is, using this connection, I was able to connect to Skype (and send/receive messages), although the sites Web could not be reached from a browser.

  I'm running out of ideas to solve the problem, but I suspect a hardware problem, so any help would be welcome.

  Yes he did.

  I couldn't find an option to delete my message, otherwise I would have done it.

• Re: Satellite L770 - unable to connect to the WiFi N project

  I can connect when I set my router "mixed b/g/n" but only 54 Mbps but if I change the router 'one n' while I can find the network but cannot connect. My most old laptop, Satellite L500D can connect mode "n" without any problem. These are the only devices connected wirelessly and the problem persists if old pc is turned off. In the interface of the routers, I see my connection has / g, older Satellite mode shows n mode as it should.

  Drivers are updated, router D - link DIR - 615 with the latest firmware.

  Hi JP75,.

  What exactly happens if you try to connect to the router N project? You get an error message or what happens?

  It is not easy to say why the works of N doesn't correctly project but first of all, I would try a driver WLAN official Portal of Toshiba:
  http://APS2.toshiba-tro.de/WLAN/

  Is it in eco mode / normal too?

• Satellite L300 - unable to connect to my router

  Hi guys,.

  I got this laptop a few days ago, everything works as it is supposed to be except for one thing, I try to connect to my wireless internet signal and it picks up the signal itself as a strong signal, but when I go to enter my WEP it never connects. I can't actually connect to the signal.

  I have another laptop which I can easily connect to my wireless signal.

  I have a wireless cable modem so it Wouldnat be my internet service,.

  Someone at - it ideas? Purchase of an additional Wi - fi adapter would work instead of using the built in Wi - fi? Also, the laptop came with Vista Home Basic installed.

  Any help would be greatly appreciated.

  Thank you guys.

  Hello

  Can you connect to the router, if you disable WEP encryption?
  In addition, WEP encryption is not safe and can be cracked in a few minutes, then you should choose another encryption WPA or WPA2.

  In addition, I would recommend updating the driver WLAN. On the Toshiba site, you can find the most recent version.

  What OS do you have? If you have Vista try disabling the WLAN card feature in Vista Power Management for energy savings.

  Good luck!

• Unable to connect to the router (even after reset)

  I'm really frustrated, and I hope that this community can provide an answer. After all the hype around this router, it is he who gave me the most trouble.

  About a month and a half... completely randomly it seems to me, I could not connect to the router more. Not through intellectual property, routerlogin.net/com...nothing. It just says: cannot display the page. I did everything I could possibly think, tried all of the suggestions I could find here and elsewhere and still nothing would work.

  I finally did a hard reset and obviously lost all my settings... and RIGHT AFTER the hard reset after upgrading the firmware, I can't connect to the router again. This could be the cause? Is there a way around it?

  The router worked fine until about a month and half ago. Then I stopped being able to connect to the admin page. Several resets hard did nothing.

  I ended up RMA'ing it and the new replacement works fine (for now).

• Satellite L500D: WiFi remove connections to the router

  My bars of Toshi Saturday 1,2,3,5 equates to dropped the WiFi but when WiFi is at 4 bars, it's the best thing since the fire.

  Recently, my laptop started to remove connections to the router and the router is that a step of 4-5 come out in the kitchen of my house. And another problem is that my room seems to be a dead zone.

  If I turn on my laptop, I am required to get out of the kitchen and stand near the router until it connected, but if I'm sitting in my room, 3 bars, and said "(the WiFi name) cannot be detected/connected."

  Any who want to enlighten me on what's going on?

  Mr.Delta

  Simply said, the Wlan router signal is too weak and this causes disconnection
  I have some advice for you;

  -Update the WLan driver
  -Card Wlan definition of control; You should go to Device Manager-> properties-> Advanced tab WLan card. You will find some options that allows you to change the standard WLan (802.11 A, B, G, etc.) and you can also check the WLan channel and improve the signal
  -Disable the Wlan Card saving

  Good luck

• Unable to connect to the router (BEFSR41 V4.0)

  I have a Linksys BEFSR41 (Version 4.0) wired router and I am not able to connect to it. It has been in storage (the top of a closet shelf) for the past two years and when it when it was still used it worked like a pro.

  I used the downloaded from the site Web of Linksys router configuration utility to install it, and when it gets to the final stage, he says that it cannot connect to the router. Try to go to 192.168.1.1 translates into a (very long) network timeout.

  I have reset the router several times (retained in the for more than 10 seconds reset button) and have had no result. All the lights on the front of the router work normally.

  I already checked and I'm set up to get the IP addresses of network automatically rather than assigning a static.

  Any help appreciated,
  ~ Darxide

  Number set by putting the ADSL modem in bridged Ethernet mode.

• Satellite P200 - unable to connect to the WLAN router

  I have a Satellite P200 and that you have upgraded from Vista to Windows 7.

  The wireless is working and to see available networks, but trying to connect it does not ask the WEP key, it just says: he has a connection problem and (possibly) says that it cannot connect.

  Someone at - it clues on this?

  Thank you.

  Hello!

  It's really strange Mavourneen. I also have Windows 7 on my Toshiba laptop, but I put t have problems to connect to my router WLAN. Everything works fine on it.

  Can I ask you if you tried to update the driver WLAN? You can download the latest version here:
  http://APS2.toshiba-tro.de/WLAN/

  Have you tried to update the BIOS?

• Satellite L500D - unable to connect to the WLAN router

  Hey all,.

  Hoping that someone here will be more help. For some reason, my laptop won't connect to a wireless network today and it was working fine yesterday.
  When I troubleshoot I get: there might be a problem with the wireless network connection card

  I called belkin and the Lady reset our wireless under a new name which we I = didn t need that my roommate who has vista had no problems with his internet. When I connect the cable through my laptop, I have internet

  Now that I see there no button on my phone to activate the wireless it connected always automatically and the led is on.

  Hi Ren,

  In the wireless issues forum, you can find hundreds of discussions on different WLAN problems.
  Did you check that?
  I think that you will find your answer.

  According to your assignment on resets the router I think that it s properly configured. Check the router security options if the SSID is visible and then encryption and password. Also, make sure that the MAC address filtering is not enabled.

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them