Satellite A40-S435: the drive cannot burn CD-R/CD-RW but can read DVD-ROM
Hello
my laptop is Toshiba A40-S435.
I'm currently problems writing CD - R or CD - RW drive CD - RW?
There is noise whenever I insert the CD - RW into the CD - RW drive!
But able to read DVD-R and sometimes intermittent reading CD - R disc?
Is - this CD - RW drive is defective? My burner is TEAC DW 224th - a 7.2 A
Or would that be the problem of software that may have a break on my CD - RW drive?
My current configuration are:
Configuration of the device is all devices
Technology HT is Enable with PM
Dynamic CPU frequency mode is always high
Speed session is seeing no tick on silent mode SET or SET Normal Mode?
You can send an e-mail and respond to [email protected]
Please help and advise.
Hello
I think it s not a question of setting wrong, but it could be a malfunction of the player.
Maybe the lens can not calibrate correctly.
I think noise appears during the insertion of the disc because the drive is trying to read or to recognize the CD.
In this case there is not much to do. You can try using different media and if this does not work if the disk needs to be replaced.
Tags: Toshiba
Similar Questions
-
Satellite A40 - 10 - D drive: for code error is not found
HELP PLEASE!
I really need help to fix errors on my system.
A few moments ago I accidentally deleted the DVD player + / optics to my laptop, and when I go to my computer, it's not here?
The sys. tells me that the D: drive is not found, and the disc has been removed without preparation and cannot be found, error code 10.What this means, as I tried to update the BIOS and it didn't need, and I can't find a driver for the A40 Satellite from Toshiba.
In addition, drivers seem to be ok and the boxes are checked in the device management, even if the optical drive has sometimes a yellow exclamation?
Tried the recovery disc and no luck.
Also the drive does not work now, because it does not read discs!Here is the Spec for the computer, as well as the summary for error messages. Reallr wouild appreciate any help on this please...
My computer science - general
Please wait while the information gathered...
100% (collecting Local disk information)
Refreshing the screen
Specifications
TOSHIBA
System model: Satellite A40
BIOS version: TOSHIBA Version 1.50Operating system
Microsoft Windows XP Home Edition
Version: 5.1.2600
Service Pack: 1.0
Location: C:\WINDOWS
PID: 55277-OEM-0011903-00111
Hot Fix: Q817606(Vivid RAM) memory
Capacity: 2 GBHere is a list of the Dr. watson error reports that appeared the donation system.
January 25, 2009 Service Control Manager the Application Management service terminated with the following error: the specified module could not be found.
January 25, 2009 atapi the device, \Device\Ide\IdePort1, did not in the expiration time.
January 25, 2009 Cdrom driver detected a controller error on.
January 25, 2009 atapi the device, \Device\Ide\IdePort1, did not in the expiration time.
January 25, 2009 Service Control Manager boot start or system start (s) what follows could not load: Cdrom
January 25, 2009 PlugPlayMa swim the device ' S I t A D D - M R - 6! 1 '' ' (IDE\CdRomT_S_I_A_D_D-R_M_S_-_ 6! 1 '___1 #3' 423362730283321372620202020202 020202020 ___\3) disappeared from the system without first be prepared for removal.January 31, 2009 Cdrom driver detected a controller error on.
January 31, 2009 Service Control Manager boot start or system start (s) what follows could not load: Cdrom
January 24, 2009 Applicatio n error Faulting application helpctr.exe, version 5.1.2600.1106 failing module kernel32.dll, version 5.1.2600.1106, fault address 0x0001a67a.
January 25, 2009 MsiInstall product Re: ParetoLogic DriverCure - 1722.There error is a problem with this Windows Installer package. A program run as part of the Setup did not finish as expected. Contact your provider to support personal or package. Action DeleteScheduledTask, location: C:\Program Files\ParetoLogic\DriverCure\D riverCure.exe, command:-deletetask
January 25, 2009 Applicatio n Hang Hanging application switch.exe, version 0.0.0.0, hang module hungapp, version 0.0.0.0, hang address 0x00000000.
Hello
Akuma is right. I tried to find Microsoft document about this, but somehow the old links no longer work.
In any case, after removing the Upperfilters and Lowerfilters optical drive should be recognized correctly again and you can use it again. -
I tried to backup using a DVD, as usual, but without success. Back to the high status and Configuration States:
Upward did not complete successfully
Original title: back to the top has not completely filled.An error has occurred. The following information can help you resolve the error:)
The drive cannot find the sector requested:
0x8007001B)I've looked everywhere for this problem... need help :)
Babette
Hello
1. have you done any software or hardware changes on your computer before this problem?2. have you checked with another DVD drive?3. using the Windows backup feature to backup?4 do you have third-party backup programs installed on your computer?To work on the issue, refer to these methods.Method 1:Step 1:If it's a DVD I suggest trying to backup to an external hard drive and check to see if you get any errors.
Step 2:Temporarily disable the antivirus software and check if you are able to perform the backup.
Caution:
Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.Back up and restore: frequently asked questions
Set up or change automatic backup settingsChange when you save your files
http://Windows.Microsoft.com/en-us/Windows-Vista/change-where-you-back-up-your-filesMethod 2:I suggest you check for errors of hard disk on the drive you want to back up.Check your hard drive to find errors in Windows 7
http://support.Microsoft.com/kb/2641432NOTE: the steps also apply to Windows VistaCHKDSK warning:
Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.Hope the information is useful. -
Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) has .dvd rw ad - 7530 ata
Hello
Code 39 means that the driver is corrupted or missing.
Please make all below even if you have done some before as it is often the set of operations which solves
the question.Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
This will refresh the default driver stack. Even if the reader does not appear to continue below.
Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitThe CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.--------------------------------------------------------------
Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
are you can reinstall the 'old'. Many use Windows default drivers however some special aura
ones. Also check the website of the manufacturer of the car.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHope these helps.
Rob - bicycle - Mark Twain said it is good. -
Cannot use internet in desktop mode, but can in Windows 8 mode. Help?
Hey having a lot of problem with Windows 8 Pro cannot use internet in desktop mode but can in Windows 8 mode?
Hey having a lot of problem with Windows 8 Pro cannot use internet in desktop mode but can in Windows 8 mode?
I found myself with the same issue - although, for me, everything was working and then stopped at random...
Since there is no useable answer to your question here, I begin troubleshooting me...
What I found was a simple enough solution which seemed to reset the internet connection in desktop mode:
1. to reveal desktop mode from the menu of charms (roll mouse over the right side of the screen)
2. Select the charm of "settings".
3. Select 'Network' in the parameter options
4. right click on the network, you're connected to, and then select "turn sharing enabled or disabled.
5 turn on network sharing
This should reset your internet settings and retrieve your desktop mode in the loop...
-
Satellite M40: Power calibration error - drive cannot burn DVD - RW more
My drive is a carpet * an oem UJ - 831S. After a screw-up partitioning job, I had to format my HD and reinstall Windows XP... and then I can not burn DVD - RW more.
Tried many programs such as Nero and a fireman, gives an error of calibration of power from the beginning.
Burning CD - r and CD - RW no problem however, and I can read CDs and DVDs of movies very well.Google and searched for a month without success, tried to blow the laser lens, but there is no dust, I tried different media, etc. I know the best answer is that the drive is done, BUT I refuse to acknowledge it because it is too big of a coincedence to stop working right after that I reinstalled XP.
An interesting note however, my laptop has not been provided with a CD of Toshiba, so I had to reinstall manually more drivers by downloading the Toshiba site, so I have a funny feeling, this could be a thing of the software/firmware, or even a framework.
I installed the new firmware 1.02 for the reader as well. I don't remember what the firmware was before resettlement, IE the laptop computer settings to factory default, I'd like to downgrade to 1.00 if possible.
Experts have ideas? And is there a way I can reset the firmware?
Maybe I could remove the drive from the system-> devices and let XP Reinstall for me?
Hello
> I don't know the best answer is that the drive is done, BUT I refuse to acknowledge it because it is too big of a coincidence to stop working right after that I reinstalled XP.
Of course, it s simply to say the drive is dead because everything looks like a hardware malfunction. Most often the power calibration error appears because of the drive lens can't calibrate in the right position and thus cannot read some CD or DVD s s or it of not possible to write about them.
But maybe you are a lucky man and might try this procedure:
-Try to remove the drive physically from the Bay for laptop
-Restart the unit without the drive
-In this case the operating system should start from the HARD drive
-Close the notebook then reinsert the drive unit in the Bay of s for laptop
During initialization, the laptop should recognize the drive and must pick up the firmwareThen you can check if you can burn the DVD again, otherwise you will need a new drive
-
Satellite U200 163 with Vista: UJ-842 drive cannot burn CD - R or CD - RW properly
Hello world
I recently purchased Windows Vista Basic and since Home Edition? m running my recorder, a carpet of this new OS on my U200 163 * a UJ-842 can burn CD - R or CD - RW properly.
I think my firmware needs to be updated, but Toshiba nor Mat * a are able to help me.You have an idea?
Thanks for your helpHello
I don t think you need to update the firmware.
I recommend using a compatible support and supported!In the user manual, you will find a list of supported CD and DVD!
Also try to burn the CD or DVD with extra like Nero burning software.
Nero supports an option to test the drive. He learned the best speed and control the burning procedure to get performance better combustion.best regards and have a nice weekend ;)
-
Re: Satellite A40-151 - HARD drive replacement
Hello
Following my previous thread (where the hard drive from the A40-151 has been slow and most later made a terrible noise and ultimately did not appear in the bios).
I would replace the drive. I went to the store today and the available drive capacity was well beyond the 30 GB Toshiba MK3021GAS unit. Started 80 GB up to 250 GB. I'm a little worried about the extra power, the speed, the conditions of heat and weather the BIOS recognizes it. Ideally, I would like to find a new MK3021GAS unit. The guy in the store seemed to think that it would be unlikely that someone would still do 30 GB (I guess than the IDE 2.5 "HDD) readers might therefore have to go down for a refurbished drive.
Are there specific readers (speed, capacity, etc.) that do not work with the laptop?
I'm suspicious to a repairer for Toshiba because the age of the laptop the labor costs can exceed the value of the laptop. However accept what are probably the only people to carry the part.
Kind regards
Ashley.Hey,.
You re right. Satellite A40 uses s HARD drive with older IDE interface. This means that you need a new 2.5 HDD with IDE interface.
As far as I know on the old IDE interface there is a limitation of LBA 28 bits and this means that the laptop can only manage hard disks up to 128 GB. So if you buy a larger HARD drive, you pay for the disk space you can use t.
So I recommend a 120 GB model or less. It should work properly! :)
-
Satellite P30-145: the drive won't recognise DVD double layer
I have a Satellite P30-145 with a SupermultiDL DVD player. When I got the PC, I could write DVD double layer with no problems. Now the drive will not recognize DVD double layer at all. Even those from the same box that has worked well before. I use are Verbatim Double layer DVD + R 2.4 x discs.
After a lot of internet research, I have downloaded and run DVDInfoPro. This application has reported that the Player did not support the DVD + RW DL. Very strange!
Can anyone help? The drive is a carpet * a DVD-RAM UJ - 831S.
Hi Lan
This disc is certainly DL one, but I can imagine that the drive is defective and cannot calibrate lens in the right position. This model of laptop is more than two years, and if you have used this drive extensively, I can really imagine that the DL function is defective.
What you can do is to clean the lens and see that it will help.
-
What to do when the driver cannot be installed
my hard drive will not read my CD. I tried everything I know. Installed the patch program, but it says driver cannot be installed. I need an answer on what to do about it.
Lillian Day
Hello
Don't forget to start as admin.
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Satellite A30-232: SD-R6112 cannot burn CD/DVD
Hello
After you have reinstalled Win XP, I can't burn CD/DVDs. The drive is a SD-R6112. It is only recognized as a CD player.
All programs have been relocated with the CD that came with the computer. I tried flashing the drive, the installation of SP2, but without success.Everything worked fine prior to the relocation.
Any idea?Hello
Please enter the properties of the CD/DVD drive! Somewhere in the properties of the drive (can't remember where), you should find options to enable recording on this device.
-
Satellite L750D - update the driver AMD Radeon HD 6320
Hello
We have a L750D and we just went back to factory settings due to a failure of the operating system.
Pre re install my wife used to run the software called studio silhouette on it without any problem.After re install the program is very slow / unresponsive and using most of the CPU.
According to 'silhouette support' re install may have missed to the old graphics drivers (as we have updated their since 2011).Silhouette must clearly be the ability to Open GL to work properly (whatever that means!) and the old graphics drivers may not. Through a program called Speccy, I found this graphics driver amd radeon hd 6320.
Anyone know if this pilot could be updated?
Thanks for your time
RussGuess what.
Visit the page of the Toshiba UE driver and download the display driver AMD ATI for the Satellite L750D series.
http://www.Toshiba.EU/innovation/download_drivers_bios.jspYou said nothing on the system you are using, but I guess its Win 7 and on this page you will certainly find the driver for this OS
-
I try to update the missing drivers, but still does not work
I uninstall deamon Tools, reboot, then do the test again and if the drive is still problomatic, in Device Manager, uninstall the cd/dvd drive and reboot again
And if the problems continue to update your drivers from Acer site, specific to your model and the version of win7 bit
-
Envy of HP dv7 laptop with windows 7 service pack 1, 64-bite.
The printer is HP Officejet 6700. The printer works fine, but there is an error on the portable device. When I troubleshoot it, it says that the driver is not available.
Went to properties, manager, open properties on the device and I get the message in the above title line. Troubleshoot it, and States he found the driver but can not install it because it is not assigned numerically.
Removed the device and rebooted the laptop using the 'requirement of Signature pilot off' and always ends with the same problem.
Follow this procedure (recommended for before service pack 1): uninstalled the device; disabled user account control; restarted; Enter the following on the command line: bcdedit/set testsigning on, press ENTER, accepted; bcdedit/set loadoptions DDISABLE_INTEGRITY_CHECKS; Press enter; accepted. Reinstalled the printer driver and restarted the laptop. Still having the same problem.
Is there a work around for service pack 1?
Fixed!
The HKEY do not have a lower or higher value.
What seemed to work.
Portable boot in safe mode.
Entered the following command at the command prompt:
Bcdedit.exe/set nointegritycheck ON.
Tried to install the printer. He would not have installed.
Changed the above command to OFF.
Tried to install the printer. He would not have installed. Perhaps you are unable to install a printer in safe mode? I do not know.
Restarted the laptop. Install the printer and the error disappeared.
Thanks for your help.
Don
-
DVD Player cannot read the DVDs (but can read busy DVD)
Hello
I have Hp Pavilion dv6-6140us, a 64-bit engine and is running windows 7... I wanted to burn the iso of windows 8, but my dvd player is not able to read blank dvd, but it can read the non-empty disc and can also play movies... Please help... want to try to win 8 preview release
Hello
Follow these steps to reinstall the Beats Audio interface.
Download IDT Audio Installer on the link below and save it in your downloads folder.
http://ftp.HP.com/pub/SoftPaq/sp52501-53000/sp52658.exe
One time finished, open windows control panel, open Device Manager and open sound, video and game controllers. Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.
When you are done, reboot the laptop and let Windows load completely. Open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation. When this has completed, restart the computer again.
Kind regards
DP - K
Maybe you are looking for
-
I put a simple password but it shows as "xxxxxxxxxxxxxxxx", but this isn't my password. How do I get my original password
-
33 Firefox works only with Amazon Wish List radio buttons
On Amazon.com, if I click on the option button "Add to wish list", my wish lists list doesn't go down for display and selection. Instead, the item is added to my wish list default (I have several wish lists). Within any given wish list, radio buttons
-
Sometimes a web page is displayed with only text and no picures. It is not always the same site and is not always the case. If I'm going to explore for the same website that always works
-
size of the string must adapt automatically to the size of the text
Hello Whenever I passed the text to the channel indicator, my size of the string must match the size of the text automatically. Is this possible?
-
Vista has ceased to connect to Internet while XP works fine
I was able to connect laptop computers XP and Vista desktop for a few years. This week my Vista desktop becomes suddenly as a local connection to 'unidentified network' wireless so no Internet. When I plugged the Vista desktop with a cable, that I