Satellite A60: Power and bios error

Similar Questions

• Satellite L505-13W and BIOS error

  Hello guys,.

  I need help from you people...

  I have a bios problem down in my laptop. The blue screen message is quotted below,

  Your BIOS is not fully compatible with ACPI, please update your BIOS.

  STOP: 0X000000A5 (0 X 00001000, 0X00000000, 0XBE298C98, 0 X 00000303)

  My system configuration
  Intel Core i5, 4 GB RAM, ATI Radeon 1 GB graphic Premium

  My vertion of the current bios: BIOS 2.10

  I searched the Web from Toshiba site for an update of the bios of verson, but could find only my current version,
  Someone help me please to find a new vertion for BIOS.

  OR if there is any methord to fix this problem

  Please help me...

  Hello

  There is no updated BIOS for this Satellite L505 series.
  The European driver Toshiba page provides the latest version of the BIOS, which is 2, 10-win
  If you've already got the latest BIOS in use.

  I put t think its BIOS issue or something bad happened to your system or motherboard started to malfunction.

  Recommend trying to install the system using the recovery disk.
  If this is not enough, recommended to contact a service agent.

  By the way: have you tried to set the default BIOS? Do this power to the top of the unit, press F2 to access the BIOS. Then press F9 to get the default settings and save the changes by pressing F10.

• Satellite A60 Power Saver error

  Hi all, I have a Satellite A60 and I get the following error at startup. "" Power of Eve A fatal error has occurred that program will be terminated code ox2. Several times while it is connected my laptop turns off and to continue I need to connect again from the beginning up to. Can someone please help with a solution. Thank you, Mark.

  Hi Mark

  The only thing you can try is to remove the energy saver and try to install it again. It is also possible that it will not help as there are entries in the registry. If there is no problem for you the best way is to reinstall the unit with recovery CD. After that it works again.

  In my opinion, it is not easy to repair some specific tools such as energy saving.

• Satellite A60 crashes and restart the cycle - missing or damaged system32\DRIVERS\Ntfs

  I have a Toshiba Satellite A60, who has recently developed a serious problem and is currently blocked in a crash restart cycle. He started with the message "missing or damaged system32\DRIVERS\Ntfs", I've read about this problem on discussion forums, but am still unable to find a solution.

  Currently on start error messages appear indicating a driver is missing or damaged, the Toshiba start page has vertical lines of missing data and on a few occasions it will fully start after a short period of time vertical lines appear on the screen and it crashes.

  I tried a number of bugs:
  * Re installed windows XP pro (formatting the hard drive and renew the partitions)
  * Update the bios on the site of toshiba in version 1.90 (I think that the update also flashes the bios, but would need this confirmation?)
  Swapping the hard drive with a portable, yet no longer starts and HD works fine in another laptop, dismissing the possibility of missing or corrupt files.

  I realize that this could be a problem with the RAM and think that the laptop has 512 fixed to the motherboard, accessable without stripping down, but do not know how to determine if the RAM is the problem. While trying these fixes, I get problems with the start of the player and can only get the disk to launch and recognize the CD about 1 to 10 times.

  Could someone suggest a remedy or a fix I can try? or suggest how they fixed a similar problem. Thank you very much

  You ssounds not very good ;(description
  The hardware malfunction appears to be responsible for the vertical lines on the screen
  If vertical lines appear also an external display, the jury may be wrong.

  You re right, I Googled, and it seems that Sat A60 supports an internal memory.
  As far as I know, this memory cannot be removed and only an electronics could solve this internal memory.
  But are you sure that the internal memory is impaired. The device supports only 256 MB internal memory and other modules are removable
  If you can try to replace

• Satellite A210 - heating and BIOS update problem

  My aunt was having problems with his A210, so she bought herself a new and gave me the old one. The problems that she has been seen was the computer kept stopping at random. I think it's an overheating problem because the laptop runs quite hot. The BIOS has never been updated so I thought that might help with this problem. in any case, when I tried to update the BIOS this error message came.

  Cannot load the C:\Users\Dan\Desktop\MK10AWF\PHLASHNT driver. SYS.
  Please verify that your accounts, if you have no administrator privileges, please sign in again!
  Access is denied.
  Error code: 5

  I am the only user on the computer so I have administrator privileges and I don't know why this error is coming. Help, please. Thank you

  > Has anyone else experienced problems with the A210 of overheating? All solutions?
  Hi mate

  I m a Satellite A210 owner and to be honest, a higher internal temperature might occur if the laptop would not get enough air to cool the internal parts like CPU and GPU.
  A few weeks ago, I used the laptop on the sofa I don't the opinion of t that the cooling that are placed at the bottom of the unit fans were clogged because of my position relax, if you know what I mean ;)

  After a short period of use, the laptop shut down automatically I was a little surprised, but I realized that air could not circulate, and so the laptop overheated

  Now, I m using the unit only on the desktop. This method is recommended, and it helps to keep the temperature at the lower level

  PS: My BIOS is updated...

• Satellite A60 - overheating and decommissioning

  Hello

  As "[email protected]", I have similar problems with my Satellite A60.

  After about 10 minutes of normal use on a hard, flat surface, the laptop starts to become very hot and turns off (obviously overheating). He started only when working with heavy editing workload, but is now it does all the time.

  Is this a common fault with the A60? I've had mine for a little more than 12 months and had no probems, and now all of a sudden I can barely use the thing! (of course, it's just out of warranty)

  Any suggestions would be very appreciated,

  Thank you very much

  Mike

  Hi Mike,.

  That strangely resembles the typical issue of overheating that can infest the laptop users. Laptops use a metal matrix (similar to a car radiator) cooling to dissipate heat from the CPU when using, and if the airway through the matrix of the clogging of dust and debris, then a thermal trigger will be used to turn off the power to the laptop.

  Air suction fans act like small vacuum cleaners and pull ambient air dust in the matrix where it gradually accumulates and blocks the air flow.

  Try to use a hose of vacuum cleaner against the aspiration air grills to pick the accumulated debris. I do this with my laptop on a monthly basis.

  Kind regards

• Satellite A60 antennas and wireless - LAN

  Hi all

  Please could someone tell me where I can get a map of wireless LAN mini pci for my A60?
  In addition, please could you tell me if the A60 built in antennas?

  Thank you very much
  Steve

  Hello

  As I know a few models A60 come with and without wireless network card. First of all, it will be interesting to know the detailed model description (A60 - xxx).

  Just FYI: I discovered that the Satellite A60-762 comes with the Atheros WLAN card.

  Good bye

• Satellite A60 - recovery and install xp problem

  I have a laptop A60 which is slightly more than 1 year.

  A couple of days, about 2 minutes after the start, the screen flashed with a new window (I was unable to see the content, it's appeared and disappeared so fast), then the laptop turned off.

  I rebooted, could not boot into winxp I received the error message (please report this problem as a load dll required) missing file. The missing files were all of the system folder.

  I then tried the recovery dvd. Everything looked fine, however, he kept failing at windows startup.

  Whenever I start the machine now, I get the toshiba logo, which now has lines of Red pixels in the columns towards the bottom of the screen. The same effect occurs when I try to recover using the recovery dvd.

  After trying this for some time, I tried to install my own copy of XP home. The laptop starts, attempts to load the files needed for the installation of winxp, gets to the core of the dll and stops with an error 4 impossible to continue.

  The recovery cd and winxp cd are in good working condition - validated it on other machines.

  Once, the winxp set up did go to the options page so I chose the repair console. I was able to run fixmbr and fixboot. It worked, then I could use the recovery dvd and successfully recovered it. About 2 minutes later, once he had everything installed, I got a blue screen of death and had to re-boot - to see that I was back to the initial situation.

  I then used fdisk to set up new partitions. ]

  Now, if I try the recovery cd, the laptop starts to load the ghost file and then the screen turns white after a while - the same thing with trying to install a new copy of xp.
  I still get the red on the screen pixels when I try the recovery cd and when I start the machine and get the toshiba logo. However, when I try to install xp from my drive, the red lines, points, appear not at all.

  My feeling is that I had a master seed virus and need a new hard drive.

  Can someone please advise me on this... What do you think that is the problem? If you think it's a virus master seed aswell, can you please tell me what you know how I can fix this or I have to buy a new hard drive. What a RAM problem or a problem with the hard drive controller?

  For now, I am going through several thoughts, but keep coming back to the boot virus master = new hard drive!

  Any help would be greatly appreciated!

  Hi Paul,.

  In this case, my inclination is to suspect the RAM modules. This is based on the assumption that the screen initial 'splash' is not on the hard disk but is stored in the CMOS chip. The fact that your get the Red pixels when it appears would indicate a problem until the hard drive is still accessible.

  If you have restored your system using the recovery CD then the Master Boot Record will also have been restored (and is not infected).

  Of course, it is perfectly possible that your hard drive may also have problems that would explain the symptoms that you experience when you try to restore you system, but want to try simply to clean the dust from your CPU radiator (with a vacuum cleaner hose) before you try to restore again.

  The restore process causes a lot of heat to be generated, and you may well find that it is having a negative effect on your laptop.

  Kind regards

• Satellite Pro 4600 ACPI Bios error

  Hello

  I have a Satellite pro 4600. When I started today the machine displays a blue screen stating that the acpi bios is not fully compliant and does not start in windows. He suggests the update of the bios I did to version 2.6, but still no luck, wont let me in in either safe mode

  Any help is appreciated

  Thank you

  Hello

  Until you want to start the operating system please check the BIOS settings and set it to ACPI > Enabled. Don't forget that your BIOS supports ACPI option. If there is no success the only solution is to reinstall the operating system and don t change BIOS settings after installation.

  Before the start of the operating system the hardware will be verified by Windows. I hope that your update of the BIOS is to download site of Toshiba and designed for your device.

  Good bye

• Satellite 2410 - HDD and technical error message

  Hi all

  I formatted and installed xp pro on my drive hard lattop via a desktop computer after I put in my laptpop (previusly under xp pro as well) the system does not load windows asking me to verify my album HARD to find errors etc etc is technichal message:

  STOP: 0x0000007B (0xF9E49640, 0 x 000034, Ox00000000, 0x00000000)

  -----

  My hard drive has been corrupted and I could not enter the bios to boot from a cd, so I used a desktop computer to format and reinstall XP.

  Any help is greatly appreciated! Help... Thank you...

  Hello

  There is always a 'risk' Windows installation on a disk in a computer and the drive before moving on to another computer.
  Because Windows is a Plug-and-Play (or rather ACPI) OS, during the installation process it tries (and usually very good succeeeds) to detect the hardware inside the computer, it is installed on and then himself set up to load the drivers required for that material specific to the 'real' boot to come.

  This means that if you after installation change your hardware, windows will load the incorrect for this hardware drivers (since it is not a new PnP device search until later in the process).

  So to summarize - this this problem that you have encountered is by design and not easy to solve.
  The easy way to fix it is to get your machine to a servicepartner and have them remove the BIOS password and then do the installation in the normal sense.
  To resolve this problem, the complicated is to search the MS Knowledge Base and see if there is a way to add mass storage device drivers to a Windows installation.

  Good luck

  Tom

• T460s delay start-up and BIOS error message ' error sending end post message me HECI disabled»

  Hi all

  I just bought T460s in the website of sale at auction...

  After you install windows, I found several problem:.

  1 I can't update my bios

  2 the machine some time having the intermittent fan noise and restart by itself.

  3 I can't seem to update intel management engine firmaware

  So, I decided to return all the bios to factory setting...

  so my laptop is fine, but sometimes the laptop take a few momet to start and send the message:

  "error sending me end of message post HECI disabled.

  di decides to put my laptop to allow the lenovo Service Center:

  the technician suggest my Planar is a problem...

  but when I checked my machine detec system my warranty has expired...

  any suggestion is appreciated...

  This my thinkpad 3, my previus SL400 and T420 machine works great

  Thank you.

  If you can get into the BIOS, try to disable AMT (under the Security menu)

• Satellite L350-153 and BIOS update 1.90

  I installed Win XP Prof SP3 on my machine. Looking for new drivers I found BIOS WIN-1, 90.
  Try to update the message as the BIOS readings not to laptop. German hotline said that it will be good. Ask a BIOS to install it with the BACK, they say - back is not available.

  Updated WIN - 1.50 succeeded while running Vista pre-installed.
  Any tips? Thks

  Can you please check this again?

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp
  Type of product > Notebook
  Family > Satellite
  Product series > Satellite L series
  Model > Satellite L350
  Short model No. > PSLD0E - check please model number on the bottom sticker
  Driver type > update BIOS

  I see is last updated BIOS version 1.50. Am I right about that?

• Satellite A60 power button / light stop in 2 colors. blue & orange

  Hi can someone tell me why power button lights in 2 different colors Blue and orange every thing seemed to be sure best ok
  Thanks in advance

  This will happen if your laptop is in stand by mode.

• Satellite A10 - 131 and BIOS update

  I want to update my bios but I can't understand how :) I downloaded the R131VOL2 Web site. When I run I get the question to insert a disk 3.5 "... but the satellite A10-131 is not a floppy drive. So I'm stuck :)

  Hi Niek,

  Unfortunately Toshiba provides only an update of the traditional BIOS for your laptop you need a USB FDD order to use the update.

  Kind regards

• Satellite A60 - Power Saver no longer works

  Hello

  I have a SA-60 Satellite 743 EN Windows XP SP2. Recently, I tried to update the drivers with those provided on the Toshiba web site. When I installed the driver for the energy saver, my laptop refused to start: it froze when the Windows XP logo appeared. Thanks to the recovery console, I managed to do restart in uninstalling and reinstalling SP2.

  But since then, I can't use the function keys, the saving for the screen and the processor and the IrDA. When I try to open the hardware configuration on the Console, a box appears with the message "Module common completed"(«Common Module fermé»). "» Can give you help to bring these functions without having to completely reinstall my OS?

  Thanks for your help.
  Sincerely,
  Yves Bertini

  Hello

  The fact is that the common modules must be preinstalled at first, before installing any other Toshiba designed the tool or utility.
  On the Toshiba download page, you can also find document instruction facilities with order of good facilities. Please check to be sure that you have installed all the things in the right order.

  Good bye