Satellite A60: Powersaver won't start no-error 0x7E

Similar Questions

• Satellite 1800-100 won't start with new memory

  My satellite s1800-100 won't start although my new memory (2nd) module is 128 MB PC100.

  I have Samsung samsung K4S281632C-TC1H module as PC100 (128 MB) memory on SLOT 1 by default.

  Although all of the features and form factors are clean, why not my Satellite S1800-100 starts? I checked the new (slot 2) memory works fine and tested OK.

  So, is there as a possibility to have a problem in the 2 Slot? Or is associated with failure of the BIOS? (there is no more recent BIOS, current is 2.20 for Satellite S1800-100).

  I am disappointed. I bought a new 128 MB PC100, to insert it in the slot 2, my Toshiba didn't boou up!.

  Important note: if I connect the new memory I bought yesterday, works very well in Slot 1.

  Please help and understanding.

  Kind regards...

  Hello

  Well, it very difficult to say why it won't start.
  I think that there are several possibilities:

  (1.) you used a bad module
  (2.) the second Bank of the Board of Directors has a malfunction
  (3.) the laptop does not support max 256 MB of RAM

  I think that point 1 and 3 is not relevant because you have tested the module and it worked on the first location. Additional the laptop should be able to handle 2 x 256 MB memory, so you should be able to use 2 x 128 MB

  I think that the second ram location may have a malfunction.
  Please check the second slot with a module of memory.

  The second possibility is to use exactly the module which is recommended by Toshiba.
  As I remember it s PC100 128 MB (PA3005U) SDRAM

• Satellite A60-174: system32\drivers\isapnp.sys error

  Hello
  After several nights and using Recovery CD e try my Satellite A60 will not work. Even though I cleaned it and cables everything is new.
  I got this error: system32\drivers\isapnp.sys

  I installed the HDD in another laptop and works very well. If I bring the disk for Satellite A60 I still get this error.

  OR Toshi stays to the debugger DLL when I try to install another version of win XP Pro.

  I think that the RAM or something in the motherboard is broken. Can I change the RAM from the motherboard?
  It would help if I add little ram additional RAM slot?
  (I use only the RAM stock because it is on the motherboard.
  any idea what may be this system32\drivers\isapnp.sys.

  It is said to start the laptop with Win XP cd original and try with a R.
  Well, this back do NOT work in this laptop.
  I can't come to the screen of Windows XP. The laptop will break the instalation before that!

  Konstantin

  Hello

  See this Microsoft Knowledge base article:
  http://support.Microsoft.com/?kbid=315311

  I also read that if the new facility does not resolve the isapnp.sys question then maybe it is a failure of module memory.
  Try to remove the module and test it with another.

  Check this similar subject announcement:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=11602&MessageID=52873

• Satellite L30 PSL33E won't start at all - the LED blinks 6 times

  Hello

  My poor mother is quite upset! Its Satellite L30 PSL33E just died.

  It completely off and now won't start at all.
  Orange light flashes six times when you press the power button.
  No hard drive, fan, screen or any other noise / activity.

  She tried without the battery.

  A kind of hardware failure, I guess.

  Any ideas what this blink code means?

  Thanks in advance,
  D.

  I put t know what the code means, but you can read it. short means 0 and 1 long

  In any case, the error code means that a hardware failure has been detected on the motherboard and motherboard replacement could help you?
  Why?

  because what is really hard to fix a motherboard for laptop very s.
  It especially not possible if you n t s have sufficient knowledge, experience, and special tools.

  I think that either you contact the ASP in your country and ask a difficulty or you'll have to buy a new laptop ;(

• Satellite Pro 6000 won't start or do something

  Hello

  My satellite pro 6000 stopped working all of a sudden.
  Power led, battery, keyboard LED is on, but nothing happens, tried to remove the battery, cd, hd and put them back, nothing seems bad.
  Also tried the back button back in case but no tip was not all good.
  It just won't start at all.

  Any ideas out there?

  Thank you

  [Edited by: moderation of the Forum]

  Do the job of seem´to LEDs ok, or they do a code flashing for you say that it is something wrong?

• Satellite P300-156 won't start or by MAIL

  Hello

  I have a Satellite P300-156 I bought a few months as damaged. The screen has been damaged and the case slightly cracked. I replaced the screen and hard drive and main card seems to have no physical damage. I've been running this system for 3 months now without any problem but, today, for some reason, it won't start or even POST. It powers on and the CPU fan starts to turn then stops and does nothing. No display (I tried external). CD player works. No beeps.

  I tried reinstalling RAM even open completely and reinstalling all connections, nothing done. Does anyone have an idea what component is gone? (CPU/GPU/RAM)

  Any help would be greatly appreciated

  Thank you

  Did you update the BIOS or something?
  For me, this is a normal behavior when the BIOS chip is faulty.

• Satellite Pro 2100 won't start at all - LED flash

  My SP2100 began to have feeding problems and now won't start at all. The AC adapter green LED is lit, that are relevant lights on the body of the laptop (although the "battery charge" light always orange these days). When I try the switch on, startup begins (in fact succeeded on occasion until this morning), however the battery indicator and the adapter lights are flashing, and everything stops again.

  On the rare occasions when I'll be past this stage, lights blinking, and the system soon shuts down again with a screen message "low battery." Until this morning, he would sometimes settle, the computer remained on, and the lights showed a State of equilibrium as usual.

  Initially I thought that the problem was of course the battery or the AC adapter, but now I'm starting to think that it is with internal PSU of the laptop (although I suspect the battery is probably tour after all this part of loading and unloading).

  Any ideas?

  Hello

  I think you're right. Flashing LEDS are a sign that hardware is defective.
  I can't say what exactly is the problem, this should be verified by a technicain.
  On the other side I don't know if it's worth to repair such an old machine.

  Good bye

• Satellite L300 intermittently won't start not

  My Satellite L300 intermittently does not start.

  When trendy DC, light power plug is green, when you press power button / stop power light is Orange boots for 3 seconds with fan started done 2 short beeps and then the fan stops and no other shoe.
  turn off the DC supply then plug again before may give him another chance.

  This can happen up to 20 times, sometimes around 3 or 4 attempts.
  When he wants to finally go, pressed power light power button green and all is OK.
  That means the light Orange?

  I checked for dust in the fan, used another power supply, tried friends memory and hard drive.

  The problem can occur every day, or every day.

  I left the battery in case it appeared the problem, the battery will not hold a charge very long.
  I would be grateful of any advise

  kevsim

  > That means Orange light?

  If power light flashes orange, it indicates the power was cut off, while the computer was in mode 'sleep'.
  But in your case I n t think that the laptop enter mode 'sleep' in your case, the power LED flashes means a hardware problem may be detected

  Perhaps your motherboard is affected

• Satellite A60: ATI graphics driver issue - Blue error screen

  Hello

  I have a satellite A60 and I've had it for a year, and now all of a sudden, I have frequent crashes. The blue screen of death was told it is caused by a driver not working not properly, namely an ATI driver.

  Hello

  The blue screen of death is usually due to a software problem or malfunction of the equipment. In your case, I recommend reinstall the graphics driver.
  See the page of the Toshiba driver for updates.
  If it doesn t help and the blue screen appears again and it would be very interesting to know the details of the blue screen, for example stop: xxxxxx

  Check it out.

• Satellite L40 - 14N won't start, if I install two 2 GB memory modules

  Computer won't start, if I install two modules of 2 gigabytes RAM, I can install vista 64 on this computer to overcome this problem, have updated bios.or is there anything else I can do.it also won't work if I put a 2 and a 1 GB of ram in.

  Any help would be apprecated

  mayala

  No, Vista 64 bit will not solve your problem. The fact is that this model of laptop only supports a maximum of 2 GB of Ram in total. For example, you can use one of your 2GB memory module.

  If you do so, laptop will start again.

• Satellite Pro P200 won't start

  I have an old 1 week per Satellite Pro P200, it turns off when I was just in the start menu, so I was not doing something out of the norm (power cable is plugged). Since then it just won't turn.

  With the connected power cable I have an electric blue, power battery and light (although attempts to restart about 2 the battery light was red, but now blue). The drive light flashes for about 3 seconds each time I try to start and I can hear something happening inside the machine, but after only 3 seconds... nothing, completely dead.

  I tried to remove the battery, wait 20 minutes or more and none of it worked. Anyone have any ideas?

  Seems to be definitely a hardware problem... very bad :(
  Why you visit your dealer for new laptop and ask for Exchange.
  Maybe the dealer will exchange the laptop with a new.

  If this isn't the case, then you must contact the service provider authorized in your country for assistance.
  If you have purchased an extra service on the spot then the technician you will visit at home and will try to solve this problem.

  Good luck

• Satellite Pro A10 won't start HARD drive

  I have a Satellite Pro A10 that is not responding. If I have the connected HARD drive I get a ' insert System Disk... "message, I checked the HARD drive with a 2.5" USB connector in another computer and it seems OK.

  The laptop, I cannot change the boot order to select CD-Rom so that I can try the recovery disks. I can't get into the BIOS, but the Boot Priority option is not selectable.

  Any help appreciated.

  Especially this error message appears because the Middle starts not able.
  You insert a boot able CD?

  Try this: connect the computer laptop HARD drive to a USB adapter and try to format the whole HARD drive.
  Then put it in the laptop, insert the bootable CD and try to boot from the drive.
  As mentioned you could press the C button immediately after you start the laptop

• Satellite A500 - Windows won't start, how to get back now?

  Hello guys,.

  Recently, a week, I bought a new Satellite A500 - 1HK. I installed everything and after I installed Office 2007, after restarting my PC put on the Windows 7 Logo. PLS, please note that at this time one had a connected external HARD disk. It was my first mistake.

  My second mistake was that after 5 minutes of inactivity, I turned off my PC (no closures) and that's it. My PC has crashed completely.

  My third mistake was that I did not since the recovery disks, and unfortunately I don't have the recovery CD. The recovery program his on a partition separate from my laptop. I tried to solve the problem as follows: I start the PC, press F8 and I went into the repair menu. The first time after the repair, nothing had happened. After that, I tried to go to the recovery option. I choose the American language and press ENTER. Nothing had happened. the screen displays an error saying: you must login to access the System Recovery Options. If you encounter problems to connect, contact your administrator to the computer for help. Click ok to restart the computer.

  The only thing I can imagine is that the recovery partition crashed also. What can I do now? I ordered alrweady the Toshiba restore CD and waits for the next 2 weeks.
  What is your opinion. That's happened? I hope that the rexcovery program will work with CD and I don't face any problem, no more.

  Thank you.
  Leonardos

  Hey Buddy,

  > I have ordered alrweady the Toshiba Recovery CD
  So in my opinion, your question is already answered. Juice wait the Toshiba Recovery disk to restore to factory settings.

  If work HDD recovery doesn't, your only option is the Toshiba recovery disc and now it s time to wait. I m you will get the disk as soon as possible.

  Good luck! :)

• Satellite A15-S129 won't start CD - message NTLDR missing

  I decided to do a new installation on my Satellite A15-S129 neighbors. After trying all sorts of ways, I decided to remove the hard drive and reformat my computer. When I put in the satellite, I expected to boot from the cd since the hard drive was empty, but no, I get the "missing ntldr message.

  The Bios does not have the cursor move on the part where I could change the boot order. When I start the computer, I can't press f2 or f12 to change the boot order.

  After no luck I just started doing all sorts of things to solve problems. A: I notice if I remove the hard drive and let the empty slot, I get error IDE, and then SURPRISE!
  The boot goes to the Conference on disarmament, BUT just at the point where I thought I could just install, I get the screen that says lack of hard drive, even though I pressed and push the HDD.

  Why the computer insists on the conduct of one thing: starting from windows xp, even if the disk is the Bank.

  Why I can't, or rather, how can he blow up the hard drive and move to the cd drive?

  I've never been stumpted like this before! Please help, my neighbour will have my head!

  Hello

  It seems that the HARD drive is ok because you were able to access it from another computer.

  But a question; How connect you and format the HARD drive internal on another computer?

  But to the A15 motorway. It s very strange that you are not able to access the BIOS and that it of not possible to change the boot order. nor by the F2 or F12 key.
  But wait this BIOS has been installed on this laptop? Phoenix BIOS or Toshiba?
  To access the Phoenix BIOS you need to press "F2", but to access the Toshiba BIOS, you must press ESC then F1.

  In any case, due to your description, I guess the hardware malfunction causes this problem.
  Maybe a problem of controller, HARD drive or other tiny part of the motherboard does not work

  I think that the technician should take a look on this laptop, and maybe he'll find the source of error.

• Satellite p205-s8811 won't start normally or in safe mode just automatically get a black screen

  I started my computer and start the recovery window came. I ran it and it has to solve the problem and computer ran very well. I stopped him and 6 hours more later powered on and the same thing. Startup recovery ran and solved the problem again.  When I looked in the log recovery startup errors he says that there are changes not specified for the configuration of the system. So I decied to do a system restore. The system restore ran, off, rebooted computer and when to start the toshiba system came on the screen. Then went black and never started window. For hard drive light was illuminated as normal, then slowed down, would be possible, and eventually it would flicker just a little more. The screen is black, but you can see the cursor. I pressed the switch to turn on, turn off, wait a little bit. Then turned on and got the screen to start normally, safe mode, safemode promt, European round table. I chose safe mode and it and all the config system starts to roll across the screen, then screen turned black and nothing else happened. So I tried again and chose to start windows normally, but the same thing. Toshiba comes through screen\, hard disk, running, but nothing but a black screen. I don't know if I app\drivers and recovery discs and don't know if it's even the fix. I could really use some help with this. I "ve been out of work for six months due to motorcycle wreck and do not have the funds for the nine. Plese I want to know if it's fixable. Thank you

  Toshiba satellite p205-s8811

  Windows Vista 32-bit

  Intel core 2 duo T5450 processor

  1.66 GHz

  disk SATA 250 GB hard drive

  17 '' display, mobile intel graphics X 3100 accl with 64 MB - 251 MB dynamically allocated shared graphics memory

  Hello

  Method 1:

  Access the link below and try to perform a startup repair, which could help us solve the problem.
  http://support.Microsoft.com/kb/925810

  Method 2:

  If the problem persists after you complete the Startup Repair, try to perform a system restore.

  un) Insert the installation disc.

  Note

  The computer must be configured to start from a CD or a DVD. For more information on the configuration of the computer to start from a CD or a DVD, see the documentation provided with your computer.

  (b) restart the computer. To do this, click Start, click the arrow next to the button lock and then click on restart.

  Note

  If you cannot restart the computer by using this method, use the power button to turn off the computer. Then, turn the computer back on.

  (c) set your preferred language and then click Next.

  Note

  In most cases, the Startup Repair process starts automatically, and you do not have to select in the System Recovery Options menu.

  (d) click on repair your computer.

  (e) in the System Recovery Options dialog box, click the operating system you want to repair, and then click Next.

  (f) in the System Recovery Options menu, click System Restore.

  (g) in the System Restore dialog box, click on choose a different restore point and then click Next

  (h) in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  (i) click Finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.