Satellite A60 turns off when the only power is connected

Similar Questions

• Satellite T130 - turns off because the low power

  My 130 just turns off without notice because of the low power, but it shows remaining 40-50% power bfore, it turns off. What is wrong with him?

  Also there is no warning of low power, it just turns off. Any ideas?

  Hello

  That s really strange and I've never heard of this problem...

  You use a Toshiba original AC/DC adapter?
  Have you checked the Web from Toshiba website for updates to the BIOS?
  Have you tested the same with OS preinstalled Toshiba?

• Satellite U300 turns off when the battery has been removed

  Hello

  I'm on the laptop with the battery in place, and the power supply plugged in.
  That's when I take off the battery (always plugged power) who, after 5 seconds the laptop powers off.

  It's not happened before and now it happens ALL the time every time I have to remove the battery.
  I noticed that when the battery is removed, the battery light is always on – if for some reason any cell phone still thinks the battery is connected.

  For me, it looks like an electronic power supply problem.

  But it s just my personal opinion

  I think that the laptop should be checked by an authorized technician.

  Contact the ASP in your country and ask for verification

  If the warranty is valid then an everything should be done for free

  Good bye

• System suddenly turn off when the external display is connected

  I have problem with my system. every time I connect a projector or a HDMI my system stays for a short time and shuts...

  Hello

  Thanks for posting your question on the Forums of community of Microsoft.

  1. The computer completely off, or only the monitor turns off?
  2. You get an error message or a blue screen while the system is turns off? If Yes, what is the exact error message you get?
  3. What is brand and model your computer?
  4. Apart to plug the projector, does this problem occurs in all other conditions also?
  5. What happens when you try to turn on the computer later, with a projector connected?

  I suggest you to check if the computer shuts down completely or only the monitor turns off. If the computer shuts down, the problem may reside with the graphics card driver that fits inconsistent or has become unstable or corrupt. Therefore, I would suggest trying the following steps and check if the problem persists.

  1. Open Manager devices by clicking the Start button, click Control Panel, click system and security, and then, under System, clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. In the list of hardware categories, find the display adapters and select the device driver you want to update, and then double-click the device name.
  3. Click the driver tab, click Update driver, and then follow the instructions. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, visit the below mentioned link:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If you are not able to update the device driver via windows update, you can visit your computer or graphics card manufacturer's Web site and download & install the latest driver. Or contact the manufacturer of your system to do.

  Hope this information is useful. If the problem persists, please post back with answers to questions for assistance, we will be happy to help you.

• Compaq 6910p - wireless adapter turns off when the ethernet cable is connected

  Hi all

  Then, when I plug in an ethernet cable (connected to a router), my wireless adapter turns off.

  He immediately turns on when I unplug the ethernet cable.

  It isn't really a problem, either connection will provide my needs of networking, but it's just weird and I don't like it.

  Using Win7 Ultimate 64 bit.

  advice would be appreciated.

  Hello:

  This is the default setting to save the battery.

  If you always want the wireless on, go into BIOS > Menu of device Configuration and activation to deactivate WLAN-LAN.

• Power problems: computer turns off when the power supply cord is unplugged.

  original title: power problems: computer shit turned off when the power supply cord is unplugged.

  I have a HP Pavilion dv2000

  Windows vista home premium/sp2

  AMD Turion (TM) 64/2 1.80 ghz processor

  1 GB memory

  32 bit operating system

  I have 2 problems with this laptop.

  !. I have lost the power cable and bought an expensive one online step (model: PA-1650-02 c. input 100-240v 1.5 put out a(1,5A) 18.5V 3. 5 = a)

  When I first plugg cord battery charge light came on the balance, then he started to come on and outside.

  now its completely off, even with the power cord plugged in. on the lower right part of the screen its showing that cord is connected to the power supply and the battery is fully charged, but as soon as I unplugg the power cord or remove the computer cut right away.

  the second problem is that the left mouse botton does not work, the work aside right very well. I went in the proprties to put it right, click on to, but who does not work either. I've updated the drivers but still nothing.

  Any help will be greatly appreciated.

  Hi aloum,.

  (a) what kind of mouse you are using?

  (b) the left button of the mouse seems to be stuck or it does not meet the click? This only happens with certain applications?

  Step 1: Test the mouse on another computer or another mouse on the test computer

  To determine whether the mouse or the computer is defective, follow these steps:

  1. test the mouse in question on a system that works, you know. If the problem appears to follow the mouse, you may need to return or replace the mouse.

  2 test a mouse you know is working on the computer in question. If the problem seems to stay on the computer, then the problem is most likely related to the software.

  In regard to the battery not holding charge

  Battery problems are often associated with the battery itself. If you encounter this problem, contact your mobile PC manufacturer. If you purchased the battery separately from the notebook computer, contact the manufacturer of the battery.

  Troubleshooting battery problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-battery-problems

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• (Redirected) Power adapter green light turns off when the laptop battery is plugged into the laptop and does not load.

  Power adapter green light turns off when the laptop battery is plugged into the laptop and will not charge; If the laptop battery is not plugged into the laptop adapter it's still green and will charge the laptop.

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Tip: when you post a message, preferable to always include the computer model.

  Bev.

• The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

  The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

  Original title: clear the display

  Click Start or press the Windows key and type power can locate the power to change recording settings in the section of the Control Panel from the list above and click on it. At the opening of the Power Options pane, click choose when turn off display available on the left side.

  

  Choose a new setting for brightness in the drop down menu on the battery . Look at all the other parameters that you feel you want to modify, and then click save changes in the lower right to apply the options you have selected energy saving.

  You can now close the Power Options pane when you return.

• printer do not wake off mode 'sleep' and does not turn off when the Start button / stop pressed or pushed.

  HP printer all-in-one B210a win 7 64 bit.

  no error message just don't wake up from power saving mode and does not turn off when the power button is pressed. must be disconnected and then turned back on. works fine until the power saving mode he did go to sleep then not answer the test print command or Toolbox controls.  power saving mode is turned off, but still goes to sleep.

  First, you will need to make sure that the printer is under warranty.  You can do it here.  So, if you are in warranty, you must contact HP at 1-800-474-6836 and the United States in computer science, international users click here.

• Accelerometer turns off when the screen is off

  When testing my application on a Z10 android port the accelerometer turns off when the screen is off. A partial wake lock does not turn the sensor back on. A wake dim screen lock is needed to re - turn on the detector. This behavior forces the screen to be all the time when an application requires the use of these sensors.

  An example would be a pedometer recording the steps throughout the day. In order to operate the screen must be turned on by the application that runs in the background. This will cause a fast draining of the battery and is not an acceptable solution.

  On Android, a partial wake lock is enough to keep the accelerometer running.

  I think this should be reported as a deficiency, a lot of motion carried since Android applications will be blocked by this and my app port is one of them.

  Tested on system Z10, model number STL100-3. Version of the 10.1.0.273 software

  The fix will appear in MR 10.2, 10.2.1 aka.

  I recently submitted a fix for the problem.

• Two questions. (1) RIP in media player 11 problems. (2) portable speakers do not turn off when the headset is plugged...

  Hey all. I desperately need help. I have a laptop "Durabook" with Windows XP meidand service pack 3 update.  The internal speakers have never turned off when I plug a headset or headphone cable of the adapter into the outlet. It is an option that I have figured out. All my other laptops have silenced the computer speakers when headphones are connected.

  The most frustrating problem I have is in Media Player when you use the tab OUT, when I insert a cd Ripper in the computer, it is not recognized.  If I close and reopen WMP (Windows Media Player) cd, the cover and all the info of the cd is here and ready to be torn APART. Once the cd ends and ejects I insert another cd and nothing happens. Once again, I've closed and reopened WMP and evrything is ready to be torn APART again.

  Please please help.  I can't be the only one who had this problem.  I removed all anti-virus programs, removed and reinstalled WMP, twice.

  I'd appreciate any help.

  Thank you all

  Carl aka theSTUNG1

  Hi Carl,

  1. don't you make changes before the show?

  Try these steps and check the result.
  Step 1: Check if a parameter to extract music select "Always".
  a. open Windows Media Player 11.
  b. click Extract, click more options.
  c. click the rip music and make sure 'Always' is selection in accordance with article "Rip CD when inserted.
  d. click ok to apply the changes and restart the media player.
  e. check if the problem persists.

  See songs Rip (copy) from a CD to your computer

  Step 2: Make sure the headset is plugged into the socket on the right
  a. connect the headphones to the right sleeve and check the result.
  b. you can also right click on the volume icon and adjust the sound settings.

  See adjust the Volume of the computer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite Pro A200 (PSAE4E) - power off when the AC adapter is connected

  I bought this laptop for my wife about 2 years, since about 6 months ago, that the laptop was randomly shut off without warning, this only seems to happen while the power supply is connected as well.

  I have read several other posts on other sites with people having similar problems.

  There are various suggested corrections, you must disable the duel core in the bios so that it works only on one heart and he spend dynamic low for fans. I did this about 2 hours ago and touchwood not a single switch off again. This however is not an acceptable solution, there is obviously much more slowly.

  Another suggestion has been updated the bios, I downloaded it now but am very worried to run it, this laptop can stop at any moment, lasting from a few minutes to a few hours. If it stops while updating to bios, I doubt that it would be good news. I don't want to make it work on the single core for the rest of the day/night to see if its stable and then go for it.

  Before that, can I make a call to the toshiba helpline, I read on the forums that this is as well a defect of design within the laptop and there's a reminder of some of the laptops in the Canada, I do not know how it rings true but still a concern to read and might be unacceptable to the owners of the A200.

  Others have advised that it is an overheating problem, it's that I reject, I running SpeedFan and showing a stable 47 temp and it allows to switch off the coast immediately when turned on, yes it could be due to dust build up, something I checked and cleared, it did not a difference for the frequent switch offs.

  Im not too well why it is only when the power supply is connected, I have not tried a different PSU, but those who have had the same problem try this and it has not solved the problem.

  When I unplug my power as well the battery seems last mabye 5 minutes at the most.

  Overall, Im very unhappy all this, toshiba is a brand of 'high' where you expect better quality and pay for it.

  If anyone has any suggestions please let me know, would be also good to hear talk of toshiba support on the issue.

  Concerning
  Florence

  Hmmmmm... interesting.

• Satellite A200 turn off when power plugs

  Computer laptop Toshiba Satellite A200 works fine on battery, taken soon hand, he goes on immediately but it works with the power of the network while its in safe mode.
  Help, please.
  Thank you

  Laptop works fine with AC power only, when the battery is removed?

• Screen turns off when the Satellite A45-S250 is moved in the direction of less

  Hello.

  I have a satellite A45-S250. I had no previous problem with this machine. However, when the computer is running too long, or it is moved in the slightest way the screen turns off. I don't even have to type very slowly - or I lose the screen.

  But also, as I have said - sometimes I won't even be near the computer and the screen turns off. When I lose the screen if the light shines on it - I can see, it's always VERY fair Sun. Generally, it will come if I use the FN + F5 button.

  I don't know if it is a screen problem or a connection problem. It occurs with increased frequency. Any suggestion would be appreciated.

  Thank you

  Mindylea1

  Hello

  From your description, I assume FL converter is defective and must be replaced. FL inverter is responsible for the background light and the typical symptom for faulty FL inverter is dimming or blinking display.

• When I pick up my Windows 7 Acer Aspire power, the computer turns off when the battery shows fully charged

  I HAVE A CHILD OF 1 YEAR ACER ASPIRE WITH WINDOWS 7, WHICH IS CONNECTED TO BE WIRELESS. BUT WHEN I GET MY COMPUTER TURNS OFF THE POWER SUPPLY CORD. THE BATTERY SAYS FULLY CHARGED. IT WORKED AND NOW IT WONT. SOMEONE CAN ME SAY WHAT THE PROBLEM IS. I EVEN WENT BACK THROUGH HIM WITH DEFAULT AND IT DID NOT HELP.

  Hello

  Are you aware of any changes made to the computer, before the show?

  I suggest to change the power management and check for the issue.

  Change, create, or delete a power plan (scheme)

  http://Windows.Microsoft.com/en-us/Windows7/change-create-or-delete-a-power-plan-scheme

  If the above does not help, I suggest you to contact Acer support for assistance.

  http://support.Acer.com/us/en/default.aspx

  I hope this helps.