Satellite A75 - switch wireless works only with the Intel wireless network adapter

Similar Questions

• BlackBerry Z10 PrintToGo works only with the new version of OS 10

  Am unable to load files using PrintToGo from the new version (10.1.0.4181) installed.

  Worked fine with the previous version and works with the Playbook (2.1.0.1526)

  PrintToGo error log:

  PrintToGoDesktop.exe Information: 0: 09/02/2013 11:33:52 - TCPClient.BeginConnect (using ServerIP:192.168.2.102, ServerPort:80)
  PrintToGoDesktop.exe Information: 0: 09/02/2013 11:33:52 - TCPClient.EndConnect)
  PrintToGoDesktop.exe Information: 0: 09/02/2013 11:33:52 - connected successfully!
  PrintToGoDesktop.exe error: 0: 09/02/2013 11:33:52 - Z10 (2ABE5757) cell phone: EXCEPTION RAISING - System.NullReferenceException: object reference not set to an instance of an object.
  on the EDGE. PrintToGo.UserInterface.Device.UploadPDFFile (String fileTransferURL, String fileName, BackgroundWorker bw, DoWorkEventArgs e)
  PrintToGoDesktop.exe Information: 0: temporary removal PostScript file 'C:\Users\Paul\AppData\Local\Temp\PtB1360.tmp '.

  Resolved, had to repair the Z10 with the PC!  Would have thought that upgrading software would have saved the environment so that this step was not necessary (played with this for several weeks and market).

• Satellite L300-2This - wireless network adapter is not listed in Device Manager

  PL. seated me in solving the WIFI issue in my newly purchased Toshiba Satellite L300-2This (PSLBGE 020004AR)

  1. me confirm - this model is equipped with WIFI as shown in the Web of Toshiba site but my device manager it is not displayed at all. (using Windows XP)-its only display Realteck LAN

  2. I installed the drivers from the site web of Toshiba - but always hardware WIFI not be picked up by any driver. Device Manager showing that a single 'Ethernet LAN' not installed-may be it is the WIFI card but once again on three pilots (real teak/intel/Ac..). which is the right selection computer-based laptop model No.? as none does not detect the hardware.

  3. confirm me - this model is NOT - equipped also BluTooth?

  Appreciate the quick response in this regard.

  Violaine Asim

  Hi mate,

  Just a simple question: have you activated the wireless network adapter using the hardware on the computer switch portable and key combination FN + F8?

  Satellite L300 is permanently equipped with wireless network card because a friend of mine had the same specifications.

  However, you should try to update the WLAN driver. Check the download page of the Toshiba driver for an update.

  Welcome them

• Satellite L - had wireless network adapter

  Unable to get a wireless connection. I checked in the Device Manager and the Realtek wireless network adapter had disappeared. Had already tried to update the driver, but I guess if the unit isn't here, he doesn't want a driver.

  Found one (I mean heritage?) Wireless network adapter Realtek by doing something that I don't really know anymore, but that doesn't seem to work and will not be an update of the driver. In addition, my USB ports do not seem to work; "does not recognize USB devices", so the wireless mouse does not work and now my DVD player does not read DVD, however seems to read CDs.

  All of these flaws could be connected in a very simple way I have not discovered yet? My computer is virtually unusable. He sends me crazy. I checked the updates of Windows and made only Toshiba many downloads etc. as I can for the last 2 years but nothing seems to work.

  Really really welcome ideas. It works on Vista.
  Thank you very much

  Hi bonce,.

  > have done as much as possible etc Toshiba downloads I can for the last 2 years
  And now you have a confused until the Windows installation where nothing works correctly of course if something doesn t work correctly you can take a driver update, but stop just install what you find. In the end, nothing will work, and your only option is to reinstall Windows because you are not able to remove all of these drivers. If you install or update a driver you really should know what you're doing!

  Anyway, if you still use the startup of the operating system pre-installed drive HARD or Toshiba Recovery disk recovery facility. This will restore the original with all the drivers and tools settings. Your laptop will be working properly after that.

  This is an accurate description on HARD drive recovery:
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm

• Satellite Pro A660 - wireless network adapter issues

  Hi guys hope you can help!

  I have a Satellite Pro A660 - 11 M Windows 7-64 bit

  The wireless network adapter does not work...

  I tried to reinstall the bios and the driver wireless.

  The wireless button is lit to Yes as the key Fn + F8 doesn't show not relevant wifi is turned on/off as usual!
  It shows also in the Device Manager and BIOS.
  Is there something I missed? Or is it a faulty card?

  Hello

  > It shows also in the Device Manager and BIOS.

  First of all, you won't find any WLan entries in the BIOS.
  But you should see the local network card in Device Manager.
  If good WLan driver has been installed, the local network adapter device should appear in devices-> network cards Manager.

  If WLan driver has not been installed properly, you'd still see an entry under network adapters, but it should appear as unknown device or Ethernet controller.
  You can this inscription?

  In addition, the WLan driver was released on the Toshiba UE driver page.
  The question is; have you chosen the right Wlan driver.
  As much as I know that the laptop supports the BROADCOM 802.11(B/G/N) BCM94313 WLan card and, as a result, Broadcom Wlan driver should be used.

• Satellite M30x-154 works only with the battery in use

  I own a Satellite M30x 154 and did so for two years. Now the laptop is more fuel with just the battery in use.
  It feeds well with the power adapter and the power indicator shows the batterys is full of 74%.

  Any ideas?

  What to say? The battery is possibly defective. The fact is that M30 x is old enough laptop model. Everything is possible.

  What happens if you start Notepad with AC adapter, then remove the connector ca? Can you use Notepad on only battery power?

• HP Touchpad browser works only with the Cisco Valet Plus router

  I bought a 16 GB HP Touchpad several months ago and had been enjoying his excellent WiFi feature with my old G from Linksys WRT54GS wireless router until I replaced it with a new Cisco Valet Plus (model M20) wireless-N Router a couple of days.

  Although I could easily and successfully, join the Touchpad to the Cisco Valet network, browser fails most of the time to load web pages.   For example, if I go to www.yahoo.com, the browser is going to slowly load the web page, or it will expire with a pop-up message error "Impossible to load the Page.   If I try to select a link from the homepage of Yahoo, it expires with the same message.  And this happens for all web pages.  If the initial page happens at all, I can then from this page a link to any other.

  I know that the issue is not with the router because I have several other devices connected to it and they are all working well, including a laptop HP ProBook, an iPad and a Wii Console, I use to watch Netflix movies on.  None of them has a problem - only the Touchpad.

  If I go into settings-> Wi - Fi, it shows that the Touchpad is connected to Cisco network.  And when I run the diagnostic system, it shows that the Wi - Fi works correctly.

  Does anyone have an idea how to solve this problem?

  I have found a workaround that did the trick.  I had to change the channel setting auto on a coded hard 1 channel wireless.

  Now, the Touchpad works very well, as well as all other devices that have worked.

• Magic Mouse works only with the latest el capitan

  Why Apple is not the problems with El Capitan (10.11.6) and it's Magic Mouse? The only way is connected to my MacBook Pro is to remove the com.app.bluetooth.plist at the end of each session and even that does not always work. When it is finally connected, the mouse connects and reconnects constantly during the session. The mouse is an Apple product, and Apple does not seem to recognize the problem or give anyone a viable solution.

  Determine that the problem is inherent in the software is an act of faith (there is no batches of messages here with the same problem).

  Try resetting the SMC and the NVRAM.

  Barry

• Samsung 850 EVO Solid State Drive works only with the MacBook Pro - Solution?

  I recently bought a Samsung 850 EVO 500 GB Solid State Drive for mid 2012 MacBook Pro father. The computer was working properly, but it was just very slow. I took the old drive and installed the SSD. I took it to an Apple store so that they could install the OS. A guy at the Genius Bar met with me and first tried to install the OS via the Ethernet cable. It is impossible to install some general error. He then tried to install it on a disc. Which also failed. He said he was not familiar with the type of error that he saw. But he said it was a mistake 'bad '. He said he saw the SSD for my SATA cable worked. He concluded that the reader must be defective. I explained how it is virtually impossible because they have a rate of close to zero. He said: "well they are produced en masse" and explained how they could install a hard drive themselves for some too expensive price. A bit annoying.

  In any case, I took the SSD back to my house and threw it in my desktop PC. It works very well. Then what should I do? Why am I not able to get the SSD to install it? From what I read, the Samsung 850 EVO should be compatible with a MacBook Pro 2012. Can I do to install it at home? Is that all I can say people at the Mac store to help them along?

  Most likely, the drive is formatted for use with Windows computers. First step would be to format correctly for Macs.

  This is Mac OS extended (journaled) with a GUID partition map.

  OS X will only be installed on a properly formatted disk.

  HTH

  Leo

• GPIB analyzer works only with the Trace of e/s on the same computer

  Following the advice on the basics of knowledge I want to capture Trace IO simultaneously with the

  Capture on the field PC Analyzer.  This is because I have to go on a customer site and only want to

  capture non-intrusive traffic GPIB.  The IO Trace does not capture the field of PC that has the GPIB +.

  card.  When I run IO path on the Test PC, it works fine.  However, I want to avoid encroaching on the

  Setting up clients to say IO Trace Facility.

  If I run a basic series write and read VI. EXE on the PC in the field and to perform only IO capture of this

  works fine (no instrument not attached - just to make sure IO Trace works on PCs in the field).  If I run the NOR

  draw on its own on the field PC, then run the Test PC controlling Instruments, IO Trace is

  does not work.

  At this point, I wonder if Analyzer and IO Trace can not run simultaneously on the same PC?

  OR Trace does not work with GPIB cards +?

  Help much appreciated.  Thank you

  Trace of e/s OR and GPIB Analyzer can be run on the same computer, but not in the way you want.

  The GPIB analyzer is actually a Logic Analyzer, which "listens" for all lines GPIB directly from hardware. For this reason, it can be run from any computer connected to your GPIB topology, even it is not involved in the transers. This allows almost completely corner the bus logging.

  Trace IO OR works with drivers OR Save function calls that are made. These function calls can only be captured the system where they are called, therefore NO IO Trace should run on the test computer. Trace IO NOR will always be a small impact on the time where the test system, due to the time it takes to connect to each call.

  -Jason Smith

• WUSB54AG works only with the safety of the new Netgear rotuer

  Just got a new router.  All my devices connect properly with the exception of the desktop computer that uses an external adapter to wireless of Linksys (WUSB54AG).

  The office is currently running SP3 of Windows XP (home edition).

  The latest driver for the card has been installed (3.0.18.0).

  I am able to connect if the security of the router is enabled OFF.

  The router has 3 security options:

  (1) WPA - PSK (TKIP)

  (2) WPA2-PSK (AES)

  (3) WPA - PSk (TKIP) + WPA2-PSK (AES)

  I understand (from Linksys technical support) is that the device MUST be able to connect using WPA - PSK (TKIP).

  My Linksys monitor indicates that the machine is connected to the access point but not the internet (when I used the WPA - PSK (TKIP).  The IP address that is assigned is 169.254.3.129 and not the 192.168.1.x expected.

  When I disable security on the router, the unit can connect and I'm a 'good' assigned IP (192.168.1.x).

  Ideas on the best way to troubleshoot and resolve this problem would be appreciated!

  AK

  I managed to change a lot of settings on my 2.4 GHz routers network settings.

  After passing it in WPA - PSK (TKIP) and by changing the mode/max speed "reaching up to 54 Mbps" - it works finally.  I guess that 'forced' somehome the router in order to disseminate the tape of 'G' rather than a strip of "N" (just guessing).

  It does NOT work when the router is in "mixed" (security) mode or when the speed has been set at a higher limit.

  Thanks for the info, if.

  I learned a lot during this process.

  AK

• printer scan works only with the new windows 7

  upgrade windows xp to windows 7 with the new HP Omni 220PC. Have a printer HP C309g-m. To scan from the printer to the computer xp, I had to use the HP Solution Center. The printer works very well with the new windows 7 program and new computer. I install wireless. No problems with it. Today when I went to scan a document with the HP Solution Center (I thought I had to use as before), this message came.

  "HP Solution Center cannot work because your device installation is not complete. Please connect the usb cable, or rerun the installation for a network installation cd. If it does not complete the installation, or you do not have the cd, access the HP help files by clicking on the start menu. "Everything I did. My installation CD said I had a version of the latest update on the installation CD, it was of no use. I went to the HP site and find a download for the drivers updated etc. I downloaded and installed. (although I don't know whether or not it was a duplicate of the drivers of devices on windows 7 for this.) I checked Add/Remove programs to make sure that the printer and the hp solultion Center have been added to the programs. they are listed. I can always scan with

  the hp Solution Center. Should I not this program to scan with this new pc? How can I scan from my printer now? I even tried to click scan on the printer, then scan to computer. the message I got was 'Try from scan of compurer. Refer to the documentation for more details ".  To be sure, I'm all mixed up now. All I want is for my scan printer to work with my new pc.  Everything works well except that scan thing, may help me understand what to do?:  Thank you

  all fixed. has crossed my computer to start then click HP click HP and open list. Went to my printer-clicked on my printer and clicked on the icon list to see if it worked correctly. This is a problem with the drivers and a box popped up with directions on where and how to download and install the devices for windows 7.
  Done this and tested it and everything works fine now. (Ihad already tried the HP site for support and downloaded and installed the fix suggested for the problem, but it did not work). in any case, its fixed and I hope that if someone has a problem, this information will help you.

• Application works only with the WAP. good with wifi

  My application works fine with wifi connection, but does not not with WAP GPRS.

  + 2 days devoted to this subject, but no success.

  Here's the code...

  Hi mantaker, yet I don't have the solution to my previous problem.

  my application using httpconnection and his fine work with Wi - Fi (the device). obtain data from the servlet. I want to use GPRS EDGE. I tried the very last day. but it's not working. even I had the name of the apn, the user name and the password. but it's not working with GPRS. Deploy the NetworkDiagnosticPublic application on device even his also does not work with WAP. and not getting not response. only works with wifi. Here is my code. n my wifi connection successfully application, but I want to do with the GPRS Edge code is

  connThread.get("http://*********.30daytrial.webappcabaret.com/Zain_Servlet/second?f1="                            + NameTextField.editField.getText()                            + "&m2="                            + AreaTextField.editField.getText()                            + "&l2="                            //+ LastTextField.editField.getText());//NOT WORKING                            //+ LastTextField.editField.getText() + ";deviceside=true;ConnectionUID=" + getWap2TransportUid());//NOT WORKING                            + LastTextField.editField.getText() + ";deviceside=true");//NOT WORKING                            //+ LastTextField.editField.getText() + ";interface=wifi");// WORKING                            //+ LastTextField.editField.getText() + ";deviceside=true;apn=internet;" +                            //"TunnelAuthUsername=internet;TunnelAuthPassword=internet");//NOT WORKING
  
     private static String getWap2TransportUid() {
  
       // Get the service book records for WAP2 transport.          ServiceRecord[] records = ServiceBook.getSB().findRecordsByCid("WPTCP");
  
            for (int i = 0; i < records.length; i++){
  
                Dialog.alert("Service: " + records[i].getName());         }
  
             for (int i = 0; i < records.length; i++)           {             ServiceRecord serviceRecord = records[i];             String cid, uid;
  
                if (serviceRecord.isValid() && !serviceRecord.isDisabled()) {                 cid = serviceRecord.getCid().toLowerCase();                   uid = serviceRecord.getUid().toLowerCase();
  
                if (cid.indexOf("wptcp") != -1 && uid.indexOf("wifi") == -1 && uid.indexOf("mms") == -1) {                    Dialog.alert("New ::  "+serviceRecord.getUid());                  return serviceRecord.getUid();                    }             }            /* String recordName = serviceRecord.toString().toUpperCase();             if (serviceRecord.isValid() && !serviceRecord.isDisabled() &&                     serviceRecord.getUid() != null && serviceRecord.getUid().length() != 0 &&                     recordName.indexOf("WAP2")!=-1)
  
                 {                 Dialog.alert("recordName: " + recordName);                     String uid = serviceRecord.getUid();                    Dialog.alert("UID="+uid.getBytes());
  
                     return uid;               }*/           }
  
            return null;  } 
  

  
  

  Yes peter, there are a lot of thread having the same issues...

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=38541#M38541

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=38328#M38328

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=38316#M38316

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&thread.ID=38157&view=by_date...

  always loads UN stuck

  See you soon...

• RV220W works only with the PPTP server on one VLAN only

  Hello

  I have a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.

  My default VLAN is in 192.168.1.1/24.

  I created a VLAN ID 10 in 192.168.50.1/24 inter - vlan routing: disabled and device management: disabled.

  (Menu network > LAN > belonging to a VLAN and multiple VIRTUAL local network subnets).

  Then I configured a PPTP server on the IP 192.168.50.200 to 192.168.50.210 range.

  Finally, I created my user.

  (Menu VPN > IPSEC > VPN users).

  The PPTP tunnel is at work, but on all of my local network and not only the VLAN ID 10.

  Any idea? ...

  This seems to be a limitation of the firmware 1.0.3.5. Firmware 1.0.4.x will support the rules on access inter - VLAN, which I hope, can be used to restrict traffic VLAN by default your VLAN ID 10.

• My Wacom Graphire4 graphics tablet works only with the pen pressure, OK in CS5 but not CS6...

  I am Windows 7 Professional 64 bit and still have the CS5 and CS6 64 bits loaded.  I've used my tablet with stylus Graphire4 with CS6 will detect all problems.  All of a sudden it only works with the pen pressure even if the stylus pressure is off.  I'm trying to use it as a mouse and frequently use shift/click when you change a mask.  I can do it no longer.  If I run CS5 the pen works as it should but not CS6.  When I first open the CS6 with visible brush the brush palette shows a hard brush, but when I open a file it turns into sensitive pressure without measure by me.  I have reset the brushes, re-installed the driver and finally downloaded a driver more but the problem persists.  Because it works very well in CS5 but not CS6 it must be a problem to Adobe.  It's very frustrating.  I enclose a composite image showing what happens to the CS6.  The right side shows what looks like the brush palette until I open a file.  The left side shows what happens when I open a file.   Even if I do not open a file and make changes within the brush palette, it immediately turns to pen pressure.  It's very strange.

  I would of course someone can provide information that could help.

  Kind regards... Ralph

  

  No answers, but in the meantime, I have come into contact with Adobe.  Problem has been resolved by phone.  Resolution is to delete the preferences file reopen CS6, date at which the PS automatically creates a new preferences file.  It was she, corrected a problem... Ralph