Satellite C660-115 - error message "Gfxui works not" at startup

Similar Questions

• Satellite C660 - 115 WLan connection only works when the power cable is connected

  Hello

  A few weeks ago, I bought a Satellite C660-115. I want to surf the internet anywhere in my house without any son/cables.
  On the first day, I had this problem: when I disconnect _power_ cable, the wireless connection will stop working.

  The Web page on my screen will always be there, but a new page loading is a problem.
  It is sometimes useful to recharge (by pressing F5), - sometimes not. It is always useful to "ip address of repair", but not for long.

  The only solution is to atach regardless of how much power the battery has still the power cord.
  When I do, it is no problem whith the connection at all.
  I went back to the store where I bought it, they related to their own wireless network and they have had the same problem after a few minutes. In the shop too attach the power cable solved the problem.

  So the problem must be in my lap top, not in my network (modem or almost).

  Doesn't this all seem familiar, and if so, how can I solve this?

  I hope that my English is understandable, I live in Holland.
  Thanks in advance!

  Here is the solution:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59177

  Change options for saving for the Wlan in Windows 7 power management

• Satellite C660 - 23 M: Volume OSD works not under Fn Key + 2 or 3 using Win7

  I have a satellite C660 - 23 M and have recently reinstalled Windows 7 to get a clean install without bloatware.

  I installed the utility Support Flash Cards and value-added products and, on the whole, the functionality of the keys Fn + F OK work and give an OSD appropriate, so that we can see what happens when you use key controls.

  Unfortunately however, Fn + 3 (the volume) and Fn + 4 (increase the volume) everything works properly with regard to actually proceed with a reduction or increase the volume control, do not show a suitable simultaneous OSD that allow to confirm the effect and adjust the level of the volume actually set.

  Can anyone help with a fix/solution please?

  Maybe stupid question now, but worked it as you wisch with Win7 preinstalled original?
  I ask this because on my NB520, I use the same combination of keys, but volume OSB is not displayed on the screen.

  I can just see this symbol in the taskbar to change.

• Satellite C660 fan error message - 18 c

  Hello. My laptop was working fine until today when I kept getting an error message, 'Warning' and reads as follows: "WARNING: a problem with the cooling system has been detected." (Next line) Please, turn off computer immediately and return it for service. »

  I turned off the laptop but I was wondering if it was possible that the fan may just need cleaning or something as I heard no problem. If I need to fix it, no one knows how much it would cost?

  We cannot discuss here on costs. It is country specific service and prices are different.
  The best you can do is contact the nearest Toshiba service provider and ask for help.

  Phone numbers and addresses, that you can find on http://www.toshiba.eu/innovation/generic/ASP_SUPPORT/

• Firefox does not start, no error message, only works in the background

  I click on Firefox it does not start
  no error message it does not start
  It works in the background in 32-bit
  I have re installed it but nothing changes

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls
  • https://support.Mozilla.org/KB/fix-problems-connecting-websites-after-updating

• Error message D: / / is not accessible on the Satellite L series

  Problems loading dvd write error message D: / / is not accessible. Cannot find help in the user manual.

  Is there something I am doing wrong? Do I need to load different drivers?
  I have tried DVD-R & DVD + R discs.

  Hello guys

  For me, it's stupid enough to write about the problem and not write what model of laptop you have. You have new models of laptops or some oldies? Do you use CD/DVD burning applications and which?

  Please try to start the recovery procedure to see if the drive can read the recovery media. Please post the results.

• Problem restoring system on Satellite C660-115

  Hi all

  Satellite C660-115 my niece has a problem and I want to make it usable for its Christmas.

  Turning on the power of the computer, which gives as a result the message: * can not find the operating system ', so I tried the system restore by pressing first the 0 key and after numerous tests, changing the order of the boot and the other (with F2 or F12)... ". But there was nothing.

  From there on, I realized that I couldn't go any further without original recovery DVD from Toshiba. So I ordered last Saturday and got today Thursday. After as indicated by Toshiba (boot sequence starts on the CD player), the system begins to load (Windows is loading files...) offer the available languages on a beautiful table, and then choose window .dropoff...

  So, until then, everything seemed to be going as it should, is that by clicking on the 'next' button to validate my choice of language, only an error message appears in a dialog box named RecoGUI:
  ERROR:. _INFO IOCTL_GET_DISK_LENGTH------------PHYSICALDRIVE0 the device is not ready.
  When I press OK, then it's in French:
  Hard drive # 0 is not available or bad RAID configuration!

  I still press OK (I have too much choice) and then submit the next window restoration which requires me to validate the language of the operating system to install... French (Windows Win 7)
  and the States: the current size of the restoration is: Expert Mode

  Yet once I click OK and a warning box tells me that: all hard drives will be completely erased. Do you want to continue?

  OK... and cmd prompt appears who says (in brief)
  Looking for the car not mounted V: V drive...
  Ckecking to the C: drive... C: disassembled!
  ending with: ERROR files copy of database recovery failed.
  Press a key to continue (if I do, I find the Toshiba screen and invites another cmd telling;

  Waiting for WEIRD to become available...
  STRANGE D: drive ready.
  Check for support in drive D; ...
  Continue...
  DrvLoad: Successfully loaded X:------Windows \ inf-battery.inf.
  No RAID - continues normally...
  Installation in progress...
  Press any key to continue... and if I do, then placed below:

  X: \ Windows-system32 >

  That's where I stayed, because I always come back to the same thing.
  If anyone could be kind enough to help me solve this problem?
  Many thanks in advance...

  + Edited & translated the message +.

  Hi Den

  On this forum, all ads are in English. Please be so kind and post in English, so everyone can understand you and try to help or give some feedback.
  Use the option EDIT and exchange some texts with English version please.

• Error messages - rundll does not - occurs on my new Equium

  I have a new computer satellite phone on Vista - about 4 weeks - and I get the error messages: rundll is not working, Windows graphical desktop does not work.

  Should I return to the retailer or ask for help on this site?

  Help appreciated - thank you.

  Before contacting the retailer I recommend you to use recovery media supplied and reinstall the OS. I hope once this laptop will work fine as before.

• Satellite C660 - 115 Win7 update stuck in the loop. SOLVED!

  I have a Satellite C660-115 which is stuck in a loop "of despair".
  I am a COMPUTER engineer support and a customer brought this laptop of mine, who was stuck in a loop of repair Win7 (64-bit prem) that simply says Win7 could not be repaired.

  I backed up the profiles of subscribers using Hiren boot CD (done chkdsk as well - everything is OK), and then did a factory restore.
  No problem at all with the restoration.

  Started doing the updates for Win7; SP1 seems to install OK without errors.
  The system then picked up 37 Win7 updates automatically and asked to reset.
  Upon reboot, Win7 entered "drvload.exe" and started an auto repair.
  It took time and the system started OK, but without any sign of SP1, looks so much like system restore to an earlier point?

  I though this update to process 3 times now and each time after that a lot of auto update, the same sequence occurs.

  How to exit this loop? What is causing this problem, which I have never seen before?

  No software has been installed, other than that of the recovery process.
  I even uninstalled McAfee, just in case this could be a problem - no change.

  Ah, just took another look. It is stated in Win7 system registers that the restoration was caused by a corrupted file C:\ci.dll. Google to find it was a sign by a rootkit virus in the HARD Master Boot Record disk (the file ci.dll itself is NOT damaged). Found a fix tool

  http://support.Kaspersky.com/viruses/solutions?QID=208280684

  It identified the rootkit and removed.
  Seems to be OK now!

  Hope this post could help others.
  Of course, the factory restore does not erase the HDD MBR rootkit...

  Thanks for sharing!

• Re: Satellite C660-115 very strange problems Wifi!

  I've been busy with a problem on a C660-115 wireless, always without success.

  Satellite C660-115
  Windows 7 - 64 bit

  The case:
  -Laptop is connected to the power supply: Wifi works fine, no problem
  -Laptop power supply disconnected: Wifi does not work, although there sometimes seems to be a link with the router access point/wifi.
  No internet/network communication
  -Laptop computer connected to power--> wifi works, unplug the power--> after a 1/2 minute or two, no internet connection...

  I tried to find a new driver, but we already use it the latest version.
  Then I turned off the feature "this computer can switch of this device to save power", without success.

  Ideas anyone?

  Check this box:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=57685&TSTART=0
  You must disable the Wlan Card saving!

• Disk problem error message: has: / is not accessible. No ID address mark was found on the floppy disk.

  Disk problem error message: has: / is not accessible. No ID address mark was found on the floppy disk. I am new to the computer world and that you just want to remove info a diskette and put the information on a CD. Can someone help me please?

  Hello
   
  
  1. are you able to use the other disks?
  2 have you tried to use this disk on another computer?
   
  The article below explains this error message. It is possible that data on the floppy drive went bad. I ask you to check whether the floppy drive works on another computer.
  Quick format in no. ID address mark results found
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;130627
   
  
  Hope this information is useful.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  The upgrade from Vista to Windows 7

  I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  Have you tried to do an upgrade installation or a custom installation?  A custom installation requires you to back up your files and settings with Windows Easy Transfer and then reinstall everything after installing the new.  If an update install does not install work, you need to do a custom.

  In addition, a Windows 7 Anytime Upgrade will not work and you get a message from a platform if you have bought a UA and tried to use it with Vista.  Vista upgrade requires a detail, a copy in the Windows 7 box.

• While the plug-and-play was still there at all, and I tried to go I still receive error message 2. could not locate the file.

  Here's the situation.

  First of all only started to the top of my Asus to find was no sound. Following up to plug-and-play service has not started. It is now removed apparently.

  Here are the solutions I tried, in and out of safe mode:

  While the plug-and-play was still there at all, and I tried to go I still receive error message 2. could not locate the file.

  In CMD sfc/scannow reached 32%, then breaks down, saying: it finds corrupted files, but could not fix.

  It Startin via msconfig did not work.

  Tried to go through Device Manager, which is completely empty for some reason any.

  System Restore is restoring before this problem. When you attempt a restore, plug-and-play service is not returned to the existence, defective or otherwise.

  I knew, but there may be malware, mutiple scans with several services did not find anything.

  I tried to contact microsoft help and they might suggest only I have upgraded to windows 10. Tried several times, and he has failed to be upgraded, every time. For the most part just download windows 10 and then by restarting the computer as if nothing happened. Any ideas on how I can fix this?

  Hello

  Welcome to the Microsoft community. I will certainly help you with the problem you are experiencing.

  I would like to ask you:

  • You are running Windows 7 or Windows 10 on your PC?
  • When was the last time it was working fine? Remember to make changes to the computer before this problem?

  Given that you are unable to complete the scan of SFC and Task Manager is empty, usually reinstall or do a repair install is the best choice of action. However, we can try to fix these files and check if that helps. To do this, refer to the steps below:

  1. Open the start menu and type "cmd".
  2. Right-click on the command prompt and click "run as administrator".
  3. Type the following commands and press ENTER after each.

  DISM.exe / Online/Cleanup-image /Scanhealth

  DISM.exe / Online/Cleanup-image /Restorehealth

  After you run these commands, restart the system and check.

  You can also view,

  Difficulty errors of corruption of Windows by using the DISM tool / System Update Readiness

  https://support.Microsoft.com/en-us/KB/947821

  If you are using Windows 7 and have the product key for this. You try to run an upgrade in Place to fix all the corruptions.

  Refer,

  How to perform an upgrade on the spot on Windows Vista, Windows 7, Windows Server 2008 & Windows Server 2008 R2

  Hope this information was useful.

• Unable to ping a website in command line with an error message: 'ping is not recognized as an internal or external command.'

  Original title: ping does not work

  In the cmd box when I try to ping from a site, I get a message saying 'ping is not recognized as an internal or external command.'

  I entered the command as follows: Office > ping www.yahoo.com

  Dan Calic, salvation

   

   

  Thanks for posting your question in the Microsoft Community.

  I understand that you are unable to ping a website in command line with an error message: 'ping is not recognized as an internal or external command.' Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1 are you facing problems when accessing Internet?

  2. have you made any recent hardware or exchange of software on your computer before the show?

  Please follow the steps and check the question below:

  a. click Start, and then type the three letters cmd in the search box and then right-click on command prompt and click run as administrator.

  b. type these commands and press enter after each:

  dir %SystemRoot%\System32\ping.exe

  path %path%;%SystemRoot%\System32

  Ping www.yahoo.com

  c. a report.

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• Error message 'setenv.ini' not found during installation

  I want to install the XP Pro version of the cd but I get the error message "setenv.ini" not found

  Hello

  This occurs if you install Windows from the Microsoft or Toshiba Recovery disk?
  In addition, it would be interesting to know what laptop you have.

  The disc is maybe scratchy check it!