Satellite C660-21Z - System Message about the error with cooling system

Similar Questions

• Had sent the message about the Blue error screen. Has been asked for more details. I hope this helps.

  Had sent the message about the Blue error screen.

  Has been asked for more details.

  I hope this helps.

  BCCode: 10000050 BCP1: FFFDF6F4 BCP2: 00000001

  BCP3: BF90DB41 BCP4: 00000000

  OSVer: 5_1_2600 SP: 3_0 product: 768_1

  Hi VASANTHFERNANDES,

  ·         You did changes to the computer before the show?

  ·         When exactly you receive the blue screen error?

  ·         What is the full error message?

  Follow these methods.

  Method 1: Disconnect all external devices and check if the problem persists.

  Method 2: Start the computer in last known good configuration and check.

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  Method 3: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 4: Follow the steps in the article to check the drive for errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  For reference:

  Demystifying the 'Blue Screen of Death'

  http://TechNet.Microsoft.com/en-us/library/cc750081.aspx

• pixel shader - get an error message about the 2.0 pixel shader

  Why do I get an error message about the 2.0 pixel shader and how can I solve this problem

  This indicates that your video card is not capable of using pixel shader 2.0 technology.
  Check that your video card is compatible with the minimum requirements of the game or software you use.

• Error message when you try to validate windows 'installation of the update failed. Information about the error - 0 x 80070424. Thanks in advance for your help

  When the computer that is running Windows 7 Home Premium 64-bit edition, I get a computer of saying error message fails genuine validation test.  This computer was purchased this year at Dell and has a valid license.  I hit the button to correct this error and tells me to download the required windows validation component.  Did and when it will install I get an error message stating "the update installation failure.  Information about the error - 0 x 80070424.

  Thanks in advance to find out how to solve this problem.

  two copies. the answer is here:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/error-message-when-trying-to-validate-Windows/320e1e6c-6224-4238-B847-003cb921c10c

• Re: Satellite C660-21Z - keyboard and touchpad began to play up

  Hi looking for help. I have a satellite C660-21Z and in recent days the keyboard started playing up, some keys don't work at all and the touchpad worked only occasionally.

  After trying different afew suggestions and uninstall last updates etc. I still had no luck, so I tried updating the BIOS when it went to reboot turned and then nothing, it's just sitting with the power light on and the fan runs and has been like that for about an hour!

  Help please!

  Do you have you stopped the update of the BIOS either completed correctly updated the BIOS?
  It might be possible that something was wrong during the update

  Try to remove the battery and unplug the AC adapter.
  Wait 30 min and then press the power button / stop for 30 seconds and then connect the battery and the AC adapter and try to start the chance good unit

• Re: Satellite C660-21Z - password lock

  Hello

  Again Toshiba Satellite C660-21Z which I set up with no problem and all updates loaded
  I can't get past the Welcome screen and the message is to reset the password with the use of usb flash stick and password recovery disk.

  How to do this or what I can without having to take the entire batch instead of purchase?

  > Have new Toshiba Satellite C660-21Z which I've implemented without problem
  Does that mean exactly? What do you mean with Setup?
  You started your laptop for the first time and preinstalled OS has finished setting up, right?

  Do you have a Windows account password?
  Sorry, but I don't know what your problem is.

• A blue screen (Stop error) has been reported. The message contains the error details.

  Hello Hello.
  can someone help me why this error is coming.
  I use a laptop lenovo.
  Error details:
  product-windows stytem, operating
  ID-1003,
  source-system error,
  version - 5.2.
  sysmbolicname-ER_KRNLCRASH_LOG,
  error code %1, %2 parameter %3, parameter3 %4 parameter 4 %5 2 parameter1

  A blue screen (Stop error) has been reported. The message contains the error details. An event with event ID 1001 might also appear in the event log. This matching event displays information about the specific error that occurred.

  Concerning

  Chandra Murali

  .net developer,

  HYD.

  Hi Murali,

  ·         What is the random question?

  Try the following.

  Method 1: Check for memory questions

  Microsoft Online Crash Analysis - windiag

  Method 2: Updated with the latest chipset and other computer device driver updates. Log in the Web site of the manufacturer to do the same thing.

• Satellite C660: Wireless Internet when remove the power supply drops

  Hello
  new Tosh Satellite C660 laptop works fine when the power supply cord is connected, soon as directed power is removed drops internet connection, usually to the second web page (the first web page is accessible, failure occurs usually when you try to access a new page)

  When I connect the power cable, internet connectivity returns as usual!

  I've been on the Advanced page setings power management,
  I have power settings "balanced" set up, and for the realtek card wireless put the plug and batttery power to maaximum settings (before they were to the maximum for diet and balanced for battery) even if it has no impact.

  The connection between the laptop and the wireless box seems 'excellent' level, the internet is the element which is a failure.

  I use the standard realteck card from the laptop (Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC) a D-Link Wireless N Router (DIR-615 ver1.00) and standard Modem provided by Virginmedia who bring them my services to wide band.

  All suggestions are welcome!
  Rick

  Hello

  Try the Realtek WLan driver Realtek page.
  www.Realtek.com.tw

  I read here in the forum that it has helped to get rid of these questions.
  Of course, you must also disable as mentioned in your message to save energy.

  Here, the other thread which confirms this driver update allows:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=58112

• Error message indicating the problem with the monitor of devices in Windows XP.

  Original title: Device Monitor

  Error message indicating the problem with the monitor of devices in windows xp. How to fix?

  Hello

  1. when exactly you receive this error message?

  2. What is the brand and model of your computer?

  3. What is the exact error message that you receive?

  Please provide us with more information about the issue so that we can provide you with the necessary assistance.

• Satellite T110-10 x gave me the error as soon as the first power on

  Hello!

  My new Satellite T110-10 x gave me the error as soon as the first power on.

  http://I25.Tinypic.com/33bhiqq.jpg

  I try to start in Safe Mode, same problem:

  http://I25.Tinypic.com/2hdvfis.jpg

  I start the recovery procedure from HDD using F8 and repair my computer options but it's «Repair my...» "lack from the advanced boot options menu:"

  http://I31.Tinypic.com/2pz9xkz.jpg

  I do same like Dwardlow and all start Norway as a new "machine".
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=53952

  Thanks a lot Dwardlow for your help!
  PS: I'm from Romania, sorry for my bad English!

  Thanks for the comments.
  Good to know that this thread has helped you.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=53952

  Thanks to user for nice workaround Dwardlow!

• With Photoshop CS6 on my iMac, I got an error message on the Setup with error # 1. He suggested deleting PS CS6 and then re - install. Idid, reinstall using Time Machine. I will then he sane error message. I recently changed my OS t

  With Photoshop CS6 on my iMac, I got an error message on the Setup with error # 1. He suggested deleting PS CS6 and then re - install. Idid, reinstall using Time Machine. Then, I got the same error message. I recently changed my OS to El Capitan.

  Migration of Mac with Time Machine WILL NOT WORK with the Adobe program activations due to hidden registration files

  Sign out of your account... Uninstall... to run vacuuming...

  -http://helpx.adobe.com/creative-cloud/help/install-apps.html (and uninstall)

  -using the vacuuming after uninstalling and prior to the relocation is necessary

  -https://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

  -Restart your computer... Sign in to your account... Reinstall

• Satellite A215-S4757 - battery life and the problem of cooling fan

  Hello everyone,

  I would like to ask a few questions abou my system: first, the cooling fan works in my view too often: almost without interruption, with brakes for 2-3 seconds. Is this normal?

  I have my laptop since last August and I think that it shouldn't be a dust problem, because it is too 'young' for this and I do not live in an apartment "dusty"...

  In any case, I think that the problem of "almost allways running fan" appeared about 2 months after I bought the laptop. I installed 'Speedfan' and I see 'HD0' temperature increases of 30deg remarks immediately after I have start the laptop, on 39deg after 1 hour.

  But the most curious is that so called "Core" temperature oscillates from the beginning between 45deg and 52deg! The fan starts each time the core temperature rises to 50deg and stops when the temperature reached 45deg. This behavior is normal?

  Is the normal temperature of 45-50deg? I use my laptop for browsing the Internet, emails, etc., no complex 3d games!

  The second thing is that the battery life is (and has been since the beginning) not spectacular: it lasts max. 1.5 hours with wireless use on, but normal laptop (don't play not DVDs or something like that). Is this normal? If so, is it because of the amd processor turion 64 x 2?

  Please help me with some tips / advice.

  P.S. I bought my Toshiba as I was travelling to the US (NY).

  Thank you much in advance.

  Conrad

  > I would like to ask a few questions about my system: first, the cooling fan works in my view too often: almost without interruption, with brakes for 2-3 seconds. Is this normal?

  I m an owner of a Satellite A210. It s similar to the A215. The A210 is a European model and the A215 belongs to the series of cell phones in the United States.
  I noticed the same thing on my A210, and I think that's a normal s behavior.

  > But the most curious is that so called "Core" temperature oscillates from the beginning between 45deg and 52deg! The fan starts each time the core temperature rises to 50deg and stops when the temperature reached 45deg. This behavior is normal?
  The 40-60deg CPU temperature is not unusual.
  The temperature could affect up to 70-80degrees by practicing a game. So Don t worry about the temperature.
  Cooling modules are controlled by the BIOS. Fan table is stored in the BIOS and it contains information about the limits of temperature and the use of cooling.
  If a certain level of temperature has been reached the cooling module begins to spin with a certain speed.

  Now, I would like to say a few words on the life of portable batteries
  Generally the duration of battery life depends on the use of portable computers.
  While playing games or watching movies the battery a lot faster.

  In any case, your laptop is equipped with high performance devices and AFAIK Vista was preinstalled on this series. The two factors (high performance CPU and GPU devices) + Vista OS need a lot of battery power. Vista needs of more resources for laptop like Win XP, and so portable computers equipped with Vista operating system run more short on battery such as laptops pre-installed with Win XP.

  Finally and above all he must know that there are different models more strong the battery with high * value of my would help run the notebook longer using the power of the battery.

  Hope I could clarify this issue.

  Good bye

• How to fix the error with the code: 0xe7210001 failed to load powrprof, object: cls

  Hello

  Dose anyone know how to fix the error with the code: 0xe7210001, message: unable to load powrprof, object: CLSD-no-it is found;
  OR: Fingerprintsoftware OR error: replicas THotkey.exe message window and the computer freezes

  Maleware scanned and virus, also in safe mode, found no infection, reinstalled driver fingerprint, but nothing has changed.

  grateful for the help!

  Hello

  > message: unable to load powrprof, object: CLSD-no-it is found;
  In my view, this would mean that there is a problem with Toshiba Power Saver
  What laptop Toshiba, you have exactly?

  Maybe reinstall Power Saver could help. You can find it on the official website of Toshiba.

• Satellite C660-B080 - FN key does not work with Win 7

  Hello

  My laptop model is' satellite C660-B080 & only part no = 'PSC0SV-02G01JAR' with windows 7 Ultimate 64 bit SP1

  I downloaded the driver from the website, but the FN key does not

  Please help me with this.

  Thank you

  Must be installed:

  -Value Added Package for Windows 7 64 bit
  -Flash utility Cards with support for Windows 7 64 bit

  These two tools are located on the Toshiba driver pages.

• Get the error message about the file cCNColms.dll missing at startup.

  I get the missing file from cCNColms to C:\windows\when dll I start and after connection as I administer. Can't find any help on the internet. I did a fixboot and have done several analyses. A fixmbr command showed that corruption but a fix can damage the disk partitions. Anyone have any suggestions? Thank you

  Using a Google search, I do not met that DLL and it has a special name, and is in the c:\windows folder so it sounds suspicious to me.  I would say that your system is perhaps currently or has been infected by malware.

  Because the MS Answers forum asks you to zero information on your system when a new question is asked, we know absolutely nothing about your system - and I would skip trying things.

  Read these instructions carefully and see what you can find:

  It is sometimes easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem by simply deleting the startup message.

  I would also not recommend you start digging in the registry to try to find the startup item and remove it unless you have a backup of your system or at least a backup of your registry, because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.

  These ideas relieve 'rapid' and sometimes risky of the symptom if they not even work at all, but they can't actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.  You don't need to try ideas that might work, you must do something that will always work all the time.

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.
  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding
  .  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information
  .  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that you had or have an infection, followed with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.