Satellite C660 - problem with the IKEA 3D viewer

Similar Questions

• Satellite C660 - problem with the upgrade from 4 GB to 8 GB

  Hello

  I have a Satellite C660-124 64-bit with Windows 7.

  I tried to extend the RAM of 4 GB (2x2gb) up to 8 GB (4x2Go), but the laptop is stuck on the 'Starting Windows' screen (I've already updated the BIOS and also if I tried with a new installation, the problem is the same).

  Aries is Kingston 4 GB PC3L - 12800 CL11 204 pins SODIMM
  Link: [http://www.kingston.com/datasheets/KVR16LS11_4.pdf]

  Please
  Thank you to

  Well well, its certainly possible to increase the RAM up to 8 GB of RAM.
  Your case looks like a new RAM isn t entirely compatible or the module could be defective.

  Toshiba says that the DDR3 RAM (1 066 MHz) 4 GB RAM PA3677U-1M4G module should be fully compatible.

  The module PA3677U-1M4G should be the same as the module of Kingston KTT1066D3 / 4G
  You certainly need a module SODIMM DDR3 1066 Mhz PC3 - 8500 204 pins.

• Satellite A500 - problem with the monitor after restoration

  Hello
  I have a Satellite A500. He has a problem with the monitor for a while, when you turn it on it's all lines etc. and you can not read but once the laptop to boot completely it is fine. My problem is that I wanted to do a restore, but I couldn't because the screen problem it started so I plugged into an external monitor and perform the restore. That has worked well.

  But now the laptop recognizes any my laptop screen. When you go to view it offers no other monitor choice other than external, I used for the restoration. I downloaded the display driver but nothing has changed.
  ANY IDEAS?

  Thank you

  (I have the disks for the restoration, if that helps.)

  > There a problem with the monitor for a while, when you turn it on it's all lines etc. and you can't read
  If I understand you right you can see when laptop starts and you see Toshiba welcome screen. Is this good?
  When you enter the BIOS settings you see thise lines too?

  Later, when you see the desktop on the external monitor, you can use the FN + F5 key combination to switch between an LCD and external monitor. Please try to use it and post comments if it works or not.

  What operating system do you use?

• Satellite C660: problem with keyboard - double or missing characters

  Hello

  Last week, I bought my first laptop - a C660.
  A few days after I bought it, I noticed that he was typing double characters or completely miss the characters.
  Now, maybe it's that I'm adjusting to the keyboard, but I was wondering if there was any problem with the keyboards?

  Jin

  Perhaps, there is a defect in material of the keyboard. Are you running Os with the factory settings? Otherwise, contact the after-sales service. they will fix for free.

• Satellite U500 - problem with the cooling system has been detected

  I have a Toshiba Satellite U 500 series, and I just got a message saying "a problem with the cooling system has been detected. Please turn off the power immediately and return it to service.
  Before that, I would like to know if anyone has had this problem and if there is a software solution?
  HIERARCHICAL

  Check HERE to see if anyone else had this problem in the past.

• Satellite A200 - problems with the AC adapter / CC

  Hello

  The problem concerns a Satellite A200 (PSAF6A-02H01N).

  Recently, there was problems with the laptop, taking several attempts to boot to Vista, it would lock up while loading or just hang and freeze just after loading Vista.
  But once it was up and the laptop running would be happy working for hours with the AC adapter is plugged in.

  The problem got worse now and the laptop will not load Vista end without crashing.
  We have now reduced the computer down to have only a problem when the power adapter is connected.
  The laptop battery will charge normally with the AC adapter is plugged in and the laptop on standby or off.

  The problem persists with the AC adapter is plugged in and the battery removed.
  The laptop will start and run perfectly with battery and no power adapter plugged. Once the AC adapter is plugged in the laptop indicates that the battery is charging and then after a few seconds it crash or freeze and the only escape is a full stop.
  The laptop will not work under the battery power for 30 minutes max.
  I checked the output voltage of the AC adapter and this seems to be a consistent 19.4 Volts.

  Is this only a problem of AC adapter or the problem with the laptop?

  Thanks in advance...

  The Canada Gazette

  I lifted the previous discussions on this problem and found one that was very similar, but unfortunately the user decided not to find the problem of the road, save money and buy a new laptop instead! Hmm. !! .. seems to me like this might be a prob. material. Maybe a new motherboard?... anyone have an idea of what are the costs for that perhaps? .. an ASP or decent technician backstreet?...

• Re: Satellite C650 - problem with the devices connected to USB ports

  Hello

  Can help someone, I have a C650 and everytime I try to connect to something to him via the USB ports, it is not "found" by the computer?

  The other night, I tried to get pictures on my phone but it wasn'; work and I put it down to a problem with the phone, but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.

  The laptop makes a beep sound as it would on an extraction device when you plug... I hope that makes sense. So I am now assuming that the problem is with my computer, is there something I can do to fix this?
  Thanks in advance

  Sorry should add - it's like nothing is plugged at all when it is, and it happens on two USB ports, not just one...

  Post edited by: leahhw123

  Hello

  What happens with plug n play like USB mouse device?
  You are able to use an external USB mouse correctly?

  > but today I tried to install something digital crafts for my daughter and during installation it tells you to insert the thing into the USB port and click Next, when I do that he's going through a lot of "research" and said then it can not be found.
  I guess this could be a problem with the software or drivers installed.

  I searched a bit and his city that he has a software is compatible with windows vista/2000/xp. Win 7 is not mentioned do not know if this could be a problem, but in your case, I recommend asking the support of this software product for some advice.

  In addition, you can try to install this software once more, check whether this USB problem appears again.

• Satellite A500 - problems with the temperature of the GPU

  The thing is playing Age of Empires online I started having problems with the temperature of the GPU. When you run the AIDA64 the CPU stress test can hold up well, but after 35 minutes the test what AIDA suspended while the GPU fan can't seem to download their revolutions, (I guess that if there was that a rise in temperature would increase the speed of rotation of the fan, don't).

  I consulted the manufacturer of the GPU, nVidia, (the graphic is nVidia GeForce GT 230 M) and tell me to contact Toshiba for other options, since, according to them, the problem is not the GPU.

  Any ideas or suggestions?

  You use your laptop to factory settings?
  Have you installed something that may be responsible for this (non-Toshiba display driver)?

• Satellite A100 - problem with the operation of the battery

  Hello!

  My laptop (I bought 1.5 years ago) has a big problem when you use with the battery.
  First of all, with a fully charged battery, the notification of "limited battery status" appears after 2 minutes of operation and after 5 minutes, he goes to the standby mode due to the level of the battery is very low.

  Then, I plug it into the AC power and the battery remains yellow for about 15 minutes light and then turns blue.
  (The battery is OK, I tested it on another satellite A100)

  What can be the problem?

  Thanks in advance!

  Maria

  Given that you have tested the battery in another satellite A100, the problem must be in the settings of your computer:

  1 > START > CONTROL PANEL > POWER SELECT THE OPTIONS ICON

  2 > you will now see a screen that shows your management food and note * one * has a tick that is a small point in a circle:

  3 > BALANCED > POWER SAVER > HIGH PERFORMANCE

  4 > THE PLAN OF POWER > CLICK ON CHANGE PLAN SETTINGS > WILL DISPLAY A SCREEN SHOWING YOUR PLAN!

  5 > GO TO > * CLICK * WHERE IT SAYS CHANGE ADVANCED POWER SETTINGS

  6 > IF YOU SCROLL THE BAR TO THE * SIGN + > BATTERY-CLICK * THE * SIGN.

  7 > YOU SHOULD HAVE: you will need to have play with these settings, or you can click on restore plan defaults to see if that will solve your problem

  Notes by clicking on the * + plus SIGN next to tany of these options below will allow you to change what event happens on your computer.

  + CRITICAL BATTERY ACTION

  + LOW BATTERY LEVEL

  + CRITICAL BATTERY LEVEL

  + LOW BATTERY NOTIFICATION

  + BATTERY LOW ACTION

• Satellite P200 - problem with the use of disk HARD original as external drive

  I've been pulling on my hair for a month now and could do with help

  I have a Satellite P200 series PC laptop and have recently updated from the 200 GB for a pair or 320 GB HARD drive. No problem

  The question I have is that the old drive of 200 GB system I am unable to use it in any other machine or according to and external storage device.
  The original secondary disc works fine few matter where I use it... (In my PS3 at the moment)

  When I install the orgional system drive in my laptop and rebuild windows it it still works 100%.
  Hance a good work of 200 GB of HARD drive.
  Take it out and serve in another machine of storage that it won't - boot all I get is cyclic redundancy errors

  I formatted, low level run endless disk tools
  WD test came back with diagnostics Test::Read 11 - cable sector error!

  Even as a drive on the original laptop is the same

  All ideas taken with gratitude that I don't want to lose a good 200 GB HARD drive

  Thank you very much
  Roger

  Hello!

  The external box is maybe defective, because you said that the HARD drive works in your laptop and the PS3 without problem.
  You can test the HARD drive in another external case?

  WD test unknown to me but I always use the Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  With the Drive Fitness Test, you can test your HARD drive. Download the CD image, burn it to a CD and boot from it. You can then the HARD drive.
  On the same site is a user's guide if you want to know more.

  Good bye

• Satellite 1905 - problem with the touchpad after awakening from Hibernation/standby

  Greetings.

  I've known a few interesting problems with my Satellite 1905 - S301.
  Whenever he wakes up from hibernation/standby my touchpad stopped accepting "taps" as a click on the left button of the mouse. It works normally with finger motion detection, but stops at all but it is quite annoying to restart the machine whenever he returns from hibernation mode.

  I've done a small workaround and after I close the laptop lid still works but this isn't the way it should work, I would have preferred that she either Hibernate than running for 10 hours without any sense;).

  Can someone give me the solution to this problem, please?
  Thank you in advance.

  Kind regards
  Akar

  Hello

  I agree with you. It s very boring to restart the machine each time to use the touchpad.
  This problem appears on the first day?

  I think there might be a software problem and, possibly, the new installation of operating system recovery CD Toshiba could help.
  I know, the complete installation is not the best solution, but it might help.

  You should also check you the touchpad. Satellite 1905 - S301 was designed for the U.S. market and so I checked the American website for available drivers.
  It seems that 5.3.203.2 is a newer version of the Alps touchpad driver for Windows XP.

  I suggest to reinstall the touchpad driver and check if there is no improvement.

• Satellite P300 - problems with the buttons of enlightenment

  First of all, I would like to apologize for my bad English, I'm French actually.

  Hi, I bought a laptop Satellite P300, a couple of days, and already I have a problem with tactile keys (one on top of the keyboard).

  Actually, the only one of the left, which is supposed to turn off the sound used to keep away the keys lights and Satellite logo. One day (and I don't know why), when I pressed her, she actually cut the sound. And now, the first two keys (mute and shortcut of windows media) do not work, but the other four (Media Player control).
  I tried Toshiba Assist, and the tool for the configuration of the pushbuttons (I don't know the English name of this tool) but I couldn't set the keys, they were not on the list "button name".

  So, does anyone have an idea how to solve this problem?

  I apologize again for my English.

  Hello

  I assume you are using Windows Vista because you bought the laptop a couple of days and so I think that you should try to reinstall the Toshiba value added Package. This package determines the buttons of the lighting that you mean and others (for example the FN keys too).

  The latest version, you can download the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  1. download the latest PPV on the Toshiba site
  2. go in Control Panel > Add/Remove programs. Find the Toshiba value added package and remove it
  3. restart the laptop
  4. download and install CCleaner. This cool cleans up the registry of Windows and system files. He should find some registry keys of Toshiba you should remove with CCleaner.
  5 reboot the laptop
  6. install the PPV that you already downloaded
  7 restart once again

• Problems with the mode live view

  I created a new page yesterday (first with the bootstrap information). Everything went well.

  When I opened again today, the 'live' view displays a blank page with a "unknown error: problem loading page". No idea what is the problem? TR

  You must have a server installed test and running to preview PHP pages in Live View mode.

  Your local testing server running?

• Problem with the Code/Design view buttons

  (My bad... maybe a clearer title will help you...)

  OK, I work with DW CS4 v.10.0 Build 4117 on a platform of Win XP Pro SP3.

  When you work with files from my site, they open in Code view.  The Split and design buttons are grayed out.  When I click the page layout button, the check mark is sometimes next to the option Code, but sometimes next to Design (even if the page is clearly displayed only in Code view!).

  To view the file in Design view or split view, click the page setup button, click on the Code, click on the button layout again, click Design or split view and then it will display the page in this way file.

  It's SO frustrating!  Is this a bug in CS4?  (I scanned through the other topics and can't seem to find anything about it.)  I don't remember having this problem with CS3 and have spoken with other DW CS3 users who also say that they have never had this happen.

  What can I do?

  Thanks in advance for any help you can provide.

  Susan

  Hi Susan,.

  I might have a solution for this one. I had the same problem. It would be 'reliable' whenever I would create a new PHP file.

  "File" > "New" > "PHP" > Layout 'None' > 'Create' - no buttons 'Split' or 'Design' (grey)

  In 'preferences' under 'File Types/errors', there is a section "open in code view".

  I removed the. The extension PHP from here, tried again and it worked!

  Maybe it will work for you.

  Good luck

  Tony

• Satellite A135 - problems with the keyboard

  Hello

  I've got aSatellite A135 - s4527 with windows XP SP3 on it.
  I was looking for the solution go PowerSaver work normally. I upgraded the BIOS to v 1.6 for a 1.7 last.
  Now I have trouble with the keyboard. It is not enough. Also, I do not know how bios rollback :(

  Can someone help me please?
  Thanks in advance

  Hello Mikachi

  Please do not be angry on me, but your ad is nothing other than chaotic.
  Initially I don't understand what you mean with normally get jobs to save energy? Normally?
  How it works on your laptop?
  For problems with tools or utilities do not update the BIOS.

  Back to the keyboard. What kind of difficulties do you have?
  Give us more information please. What exactly happens?