Satellite C660: Wireless Internet when remove the power supply drops

Hello
new Tosh Satellite C660 laptop works fine when the power supply cord is connected, soon as directed power is removed drops internet connection, usually to the second web page (the first web page is accessible, failure occurs usually when you try to access a new page)

When I connect the power cable, internet connectivity returns as usual!

I've been on the Advanced page setings power management,
I have power settings "balanced" set up, and for the realtek card wireless put the plug and batttery power to maaximum settings (before they were to the maximum for diet and balanced for battery) even if it has no impact.

The connection between the laptop and the wireless box seems 'excellent' level, the internet is the element which is a failure.

I use the standard realteck card from the laptop (Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC) a D-Link Wireless N Router (DIR-615 ver1.00) and standard Modem provided by Virginmedia who bring them my services to wide band.

All suggestions are welcome!
Rick

Hello

Try the Realtek WLan driver Realtek page.
www.Realtek.com.tw

I read here in the forum that it has helped to get rid of these questions.
Of course, you must also disable as mentioned in your message to save energy.

Here, the other thread which confirms this driver update allows:
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=58112

Tags: Toshiba

Similar Questions

  • Satellite C660 - wireless connection works with AC power

    I have problems with the connection Wireless on my laptop. It works when I plug in the power supply. It does not work when the laptop is running off the battery voltage.

    Is it possible to get the wireless to work without AC power?
    Thank you

    Please visit http://aps2.toshiba-tro.de/kb0/TSB12033H0001R01.htm
    I hope this will help you.

  • Satellite L750 slows after plugging in the power supply

    Hello everyone

    It's almost a year since I have TOSHIBA L750-12 model q PSK2YE-05P00RPL.
    Since the beginning, I noticed strange shares: when the battery becomes low at 10% and I plug the power supply everything starts to work slowly (for example I can see frames when using the webcam)
    also, web sites load very slowly or not at all. It's doing my work on laptop almost impossible.
    When this problem occurs, there are a few bugs in Event Viewer:

    Event 37, kernel-processor-Power
    "The speed of the CPU 0 in group 0 is restricted by the system firmware. The processor is in this state of reduced performance for 71 seconds since the last report. »

    I thought it was the power supply problem or motherboard to power so I sent the laptop to the service. Technical support only changed the BIOS to version 3.60 [there is not an another atm version] and he has not solved anything.
    I searched the internet and I found that this failure can occur because of the Enhanced Intel SpeedStep Technology option, but unfortunately I can not disable it in the BIOS.

    I read that there was problem simillar with for example Portege R835-P84 and new BIOS helped and solved this.

    Please help :(

    PS Sorry for my English.

    I also imagine that new and modified BIOS can help with this, but if Toshiba doesn't offer it there is nothing you can do, especially with the SpeedStep technology options.

    Maybe stupid question now, but when you connect the battery change the plan power high performance is a laptop s performance difference?

  • Satellite P750 - Wireless disconnects when wake the portable computer from the 'standby mode '.

    Hey

    Today, my Toshiba Satellite P750 (running Windows 7) has been disconnected from my wireless network when I wake from sleep mode. When I close the lid of my laptop, it goes automatically into mode 'sleep', and when I open it, I put my user password and use it as usual. However for some reason any today, it does not work.

    When I wake up, it recognizes my wireless network is available, however, cannot connect to it. When I solve the problem, it indicates that there is a problem with my router and I should turn it off, wait at least 10 seconds and then turn it back on. I tried this and it works fine, but my laptop has never done that (in the few weeks I got it) and I wouldn't constantly reset my router to use Internet. In addition, I have another laptop at home that works very well.

    Should be really this issue be resolved quickly as I have exams this week.

    See you soon

    Hello

    Maybe there is a problem affecting the IP automatically once the laptop has been in sleep mode. It could also be another reason for it but it of always difficult to say which could affect wireless networking

    I think you should try to update the Wlan driver.

    Don't know exactly what you have but here the card Wlan, you can find all the latest WLan drivers available for Toshiba laptops:
    http://APS2.toshiba-tro.de/WLAN/

    Uninstall the old drivers first, after new reboot install new drivers downloaded for the wireless network card that is built in Notepad.

  • Satellite Pro 480cdt: how to replace the power supply and memory?

    I broke the tip of the power where it goes to the back of the computer. The two pins came away from the cable. What is the size of the plug round I am looking for as a replacement? Assume that there is a standard fitting of Toshiba.

    The right size to upgrade as the memory is 128 MB. He got 64 MB it's 2 x 32 MB. I guess we're soldered in, but I can remove the other 32 MB and put the 128.

    Are these modules memory square-shaped?
    Finally, a link to the service manual would be very helpful.

    Thanks in advance.

    Hello

    It's really an old unit and it is not easy to find a lot of information. I found the info that this device can use 160MO max. Module of RAM compatible RAM are:
    16 MB PA2039U
    PA2040U 32 MB
    48 MB PA2041U
    128 MB PA2042U
    I don t really know where is placed expansion slot memory but check the underside first. Otherwise, that it may also be placed under the keyboard.

    Replacement of plug power is a bit complicated, and in this case I can't help you at all.

    In any case good luck with your oldie!

  • Is it necessary to safely stop a raspberry Pi or I can just remove the power source?

    Is it safe to simply remove the power supply or which perhaps will lead to damage to the file system of the SD card, so a security sudo shutdown - hP now is mandatory?

    Just FYI-

    I had suspected as much, but a good reason to stop IP before disconnecting the power supply because it will help prevent the corruption of the file jwc_properties.ini.

    See this post.

    Tom

  • System fails to recognize the power supply and will not charge the battery

    Had motherboard replaced but, before that, I had tried a secondary power to check if my principal could be faulty.  Card mother equipped now and all working fine except that I can't get the sytem to recognize my main diet.  Battery won't charge and the system stops if I remove the power supply.  This is on a DELL XPS M1530 laptop.

    Thanks for all the ideas.

    Hello

    Motherboard might not be properly installed or has problems - easy to miss a rider or
    any other connection as well.

    Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
    eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
    them and be careful). Batteries are old, or it could be a problem with the computer.
    Check with the support of the machine system, and many of them have on line forums.

    New Lithium-Ion type battery usually last longer if you do not unload then less than 30%
    However on a laptop that not extend their life a lot. Best is to use the a/c adapter
    When this is possible.

    I use the free version of BatteryBar to monitor my battery. Click on the green button on the
    Yellow box on the right side of the page to download the latest stable version.

    BatteryBar - free version available
    http://osirisdevelopment.com/BatteryBar/index.html

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    You can also check with the manufacturer of system and forums that many use their own
    proprietary software to monitor the battery and they could be known problems with your battery.

    ============================================================

    Try this - to make a Restore Point

    How to create a Vista System Restore Point
    http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    Then Control Panel - Device Manager - Batteries - Double click on each item - tab drivers - update drivers
    (who can not do anything) - then do a right click and UNINSTALL-REBOOT which will refresh the driver
    Stacks.

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • Satellite A500 - battery light flashes when connected to the power supply

    Win 7 Satellite A500 PSAM3A-03P00E.

    Battery light flashes when connected to the power supply (intermittent fault), when I disconnect the sector and reconnect the flashing stops and battery (high capacity) continues to receive.

    Also, when battery light blinks the keyboard backlight stays on when it should white and if the backlight is turned off and the battery light starts to blink the keyboard backlight turns on, all other functions seem to work well.

    Charges of battery and the wedges load properly (when the battery flashes).

    Hello

    Have you noticed this problem since the first day of purchase?
    Theoretically, it could be possible that your battery begins to malfunction
    On the other hand, an electrical problem could also be possible

    However, try this:
    Remove the battery and the AC adapter. Then press and hold button power 30 sec long.
    Then insert the battery and plug AC adapter still does that help?

    By the way: this is the BIOS updated? If this isn't the case, perform an update.

  • Satellite Pro A300 freezes when on the internet

    Satellite Pro A300 freezes when on the internet & the only way to turn it off is to take out the battery. Bought new Dec 2010 & is under warranty - suggestions?

    Hello

    have you tried to update drivers Lan (wlan)? What browser do you use? I guess, the Internet explorer, try firefox or opera. Also, your computer may be infected with the virus, or blocked by the firewall. Have you installed software before it starts? Is this ok when you bought it? I ask you too, because you do not have a lot of information.
    It is especially the driver, software problem.

  • When you try to reinstall Vista the following message is displayed: must remove the power cell.

    Try to reinstall Vista via the Vista installation disc.  However, the following message appears: must remove the power cell.  What is a power cell and what is the solution for a re - install?

    Thank you

    Rick

    Hi Rick,

    1. you are trying to boot from the disc or start on the desktop to start the installation?

    If you don't have any concerns of data, you can continue the installation without removing the program.

    If you have any concerns of data, then try to remove the PowerShell and run the install. Also perform a backup of important data before reinstalling Windows Vista.

    Refer to Microsoft KB article for more information:

    You cannot pass a Windows operating system when you have Windows PowerShell 1.0 installed

    http://support.Microsoft.com/kb/950376/en-us

    Hope this information is useful.

    Jeremy K
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Re: Satellite P850 full face feels 'sparkling' when it is connected to the power supply

    Hello

    I recently bought a P850 138.
    Whenever the power supply is connected and turned on the laptop case computer feels strange to the touch, and if you move your hand through it, as you often eventually do during the strike, etc., you get this weird 'static' y feeling.

    When you are disconnected from the power grid the sensation continues for a short while, but soon after the case feels just like normal metal again.

    I guess that something happens which is originally the case become statically charged, but does anyone have any ideas as to why what is happening? Is this a common problem?

    Any ideas?

    Thank you very much in advance for your answers

    Hi neh23

    It's the first time I read on this subject and in my opinion its definitely not a portable common behavior I think you should get in touch with a Toshiba service provider in your country to check the laptop.

  • Satellite P100-347 does not stop when it is used on the power supply

    I have a new laptop of P100-347 games and I have 2 problems. Can anyone help?

    (1) when I use the usb port on the left side of the laptop, the laptop seems to restart the same time that I plug anything into it! I called Toshiba and said to update Bios, so I did (version 240 up to 330). But as soon as I did it started to the following problem:

    (2) when I run the laptop on battery, I can turn off the phone by pressing the power button or by clicking the windows locked. But as soon as I plug the power supply whenever I want to stop the laptop, the laptop just restarts. Does anyone have any ideas?

    Thanks for the comments!

  • Satellite C660 - WLan disconnects when on battery

    Hello

    Please forgive my ignorance on this, but I'm just trying to establish whether the problem is with the laptop.
    I recently bought by Satellite C660. I loaded the internet as I have done with so many other pc, and if the charger is connected (even if does not load) I can connect to the internet and keep in touch without any problem.

    As soon as I remove the CAP, because obviously, I don't want to keep plugged in when the battery is full - I lose the internet connection - comes with limited access and that's it, impossible to surf.
    It can be something completely stupid that I have or have not is but I really would like help any with this question that it's starting to stress out me.

    I also tried other internet devices that seem perfectly ok and my signal is excellent.

    Please help, thanks in advance

    Hi mate

    Please take a look here:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59177

    You can solve this change of economy option WLan Card in Win 7 the power supply management.

  • Satellite C660-11KLoss WiFI connection on the battery

    I recently dgraaged myself in the 20th (Yes 20th) century and went wireless.
    I have a portable Satellite C660 - 11K which connects to 1683B 8 Talk Talk. When using the power cable connection is perfect.

    However, when you use the laptop battery, internet connection is often lost.
    The signal strength is very strong with and without connection to the sector.

    Any ideas please?

    Hello

    You will find an answer to this question if you want to use an advanced Forum search option.
    You will find these discussions:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59143
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=58744
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=57685

    Please post feedback after you have fixed this!

  • Satellite C660 - 1 7 - cannot run the BIOS update

    Hello

    I use my Satellite C660 - 1 7 for a year now, and recently I have a Wi - Fi connection problem with my laptop. I can find the network in my laptop, but it loses the connection permanently. It's a little boring.

    Then I tried to update the BIOS update, but each time, he showed "there is an error occurred, please check below the elements." BIOS version more than 200. battery capacity more than 10%. AC is fixed. "Well, I checked, and it is" TOSHIBA 1.40, 2011/1/21 '. "

    Can someone help me please?

    Thank you

    >... but it loses the connection permanently. It's a little boring.
    Do you have this problem with power supply battery only or is the problem when the laptop is connected to the power supply running too?

Maybe you are looking for

  • My Skype won't open...

    When im trying to run Skype it appears on a second and disappears :/ I don't know what to do, I tried to reinstall but nothing... In (Microsoft Management Console) event viewer I had loads of information on SkypeUpdater when im trying to run Skype :

  • How can I get my apps on my home screen?

    I recently played with the settings on my phone and now only have the apps that were previously loaded. Other applications such as bank etc. store loyalty cards have disappeared. Can someone tell me what I need to please.

  • This accessory can be supported

    I have a 6 IPhone on ios 9.2. Whenever I plug a charger into the charging port the phone displays "This accessory can be supported." Then he runs down to 0% and turns off. I will then be able to charge the phone to 3 percent. Then it lights up and di

  • Validity of student LabVIEW version

    Hi all I think the purchase of labVIEW student edition for my own personal use. So, can someone please tell me if there is any validity period for Student Edition and if there is, what is? Validity period, I mean how long can I use the software befor

  • Portable 2 x detachable envy: envy x 2 detachable

    Just bought today the desire x 2. Once the installation is complete, I went on the internet. All of a sudden, this little box appears which says: "Switch between applications. Shot from the edge to go back the last app you were using. Tip: Start with