Satellite C670 problems start after upgrade of Windows 10

Similar Questions

• Satellite U940 really slow after upgrade to Windows 10

  Hello

  Just upgraded the Windows 8.1. Windows 10 installation on my laptop U940-100 with 32 GB SSD for implementing caching.
  The laptop really performed very well (fast start etc.) until this upgrade.
  It seems that on the SSD caching does more.
  Anyone familiar with this problem? I can't find any useful information on the Toshiba site.

  Thanks in advance!

  Hello

  I had the same problem of yours on my 940-11 K,

  I solved it very easily just by installing the drivers for fast boot Intel and Intel Rapid Storage Technology drivers.

  You can download the latest version from the Intel site, here is the link:

  https://Downloadcenter.Intel.com/Dow...art-technology
  https://Downloadcenter.Intel.com/it/...-rapid-storage

  I have upgraded to Windows 10, then I installed the drivers.
  After each driver installation, I did a reboot.
  SSD caching should automatically work again after these 2 steps.

  You should see an improvement in performance just after.

  I hope this will help you!

• Satellite L300-215 - BSOD after upgrade to Windows 7

  Just upgraded 32 bit Vista to Windows 7 32 bit but keep getting BSOD (Blue Screen Of Death) when using the laptop. The events of the problem like log file below and it fails every time is same error code except BCP2 can change different Hex value.

  Have Toshiba upgrade disks used and all uninstalled programs that he asked me to do it before installing Windows. Model is L300-215 and laptop worked OK before upgrading to Windows 7. Have you tried the drivers audio and graphics of the site Web of Toshiba (old version of what was on the laptop after upgrade), but always the same question :-(

  Any help would be appreciated if someone else seen this error before?

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7600.2.0.0.768.3
  Locale ID: 2057

  More information about the problem:
  BCCode: 4th
  BCP1: 00000007
  BCP2: 000B458A
  BCP3: 00000001
  BCP4: 00000000
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 768_1

  Hello

  When you get exactly this BSOD? Happens immediately or if you start a certain application?

  Have you checked for yellow exclamation marks Device Manager? Maybe a driver isn t working properly and you should update it.

  Also make sure that your BIOS is up to date. You can download the latest version on the Toshiba site.

  Last but not least blue screen often associated drivers or memory modules defective RAM. The latter you can check using Memtest86.

• Satellite L755 - no webcam after upgrade to Windows 10

  Hi guys,.

  I recently updated my laptop (Satellite L755) 10 Windows in Windows 7. I have problems with the Web camera driver.

  Pls help

  Hello

  I read that you can use your old drivers of webcam Windows 8.1, and your webcam should function normally again.
  You can check this?

• Update the system: does not start after upgrading to Windows Vista SP1.

  
  

  I had the same problem. Called Lenovo, the response was:

  N ' - what is Vista come with SP1? No! Then, it is not a supported configuration. You're on your own! Bye: Pei

  Well, there is a feature called "Automatic updates" and Microsoft forces you to use - and you're foolish to not use it! In any case, I hope the support to the Denmark, named Thomas, and his bosses to get a better attitude towards customer.

  My question was simple. He was missing a Windows Service called "system update". It is implemented in "C:\Program Lenovo Update\SUService.exe.

  I had register service menually. There is a tool in the .net framework called InstallUtil.exe. The SUService.exe is implemented in .net, the InstallUtil can help.

  Start a command prompt by right-clicking and choosing "run as Administrator".

  Run:

  C:\Windows\Microsoft.NET\Framework\v2.0.50727\InstallUtil.exe "C:\Program Update\SUService.exe Lenovo."

  Modification of traces according to needs. If InstallUtil.exe is missing, it could be part of the .net SDK - do some research on Google.

  Go to services (in the contral Panel - administrative tools) and start the newly created service "system update". System update now worked for me.

• Satellite S70 - Numlock issue after upgrade to Windows 10

  Hello

  I just upgraded my S70 to windows windows 10 8.
  Everything seemed ok except that now when I press numlock the computer just beeps and the light comes on and off.

  The keypad is actually useless now (direction feature is present regardless of the State of the num lock key).
  There are no updated drivers and my laptop has its language settings for the keyboard like Qwerty of the United Kingdom.

  When I look at the overview of keyboard I don't see in the diagram of a keyboard. Can someone help me please the most frustrating.

  Thank you

  Try this to restore the NUM keys will

  Control Panel
  Ease of access Center
  Set up mouse keys
  Other settings: use MouseKeys when Numlock is: make sure that the OFF is selected.

• WLAN on Satellite Pro L770-12R after upgrade to Windows 10 has lost

  OK, first of all, I must admit that I know very little about computers so be gentle!

  I have some cleaning on my laptop and uninstall programs I didn't need. All of a sudden my WiFi stopped working and there is no wireless option when I try to connect to the internet, it shows just connect using a cable. I guess that means that I accidentally uninstalled some software required to connect to the wireless internet.

  How can I get it back? Thank you!

  Natalie

  Hi Natalie

  Can you please tell us which model of laptop and operating system do you use?

  Please open the Device Manager and check the first WLAN card status. Wireless network card must be listed and properly activated it. As an example, I send you a copy of my laptop screen.

  

• Intel technology quick start error in event visors after upgrade to Windows 10

  Hello

  I get questions with technology Intel Rapid Start after upgrade my Portege Z30t-A-103 to 10 Windows.

  The Windows Event Viewer shows:

  irstrtsv
  Error: Cannot read LBA sector directly

  I tried to disable the technology Intel Rapid boot from the BIOS, but it seems that the problem is not resolved.

  Any ideas?. I guess that an Intel Rapid Start driver technology is coming.

  Kind regards

  Intel might be the point to approve their Windows 10 pilots, at the same time just keep it disabled in BIOS for now.

• No CD/DVD drive after upgrade of Windows 8 on Satellite Pro S300L

  The cd Rom drive no longer works after upgrade to Windows 8.
  The drive is not displayed in the Solution Explorer, either. It is mentioned: error in the register.

  I can not change the right driver in Device Manager - probably it was deleted.
  Is the driver of the * MATHSITA DVD-RAM UJ880AS drive * for Windows 8 available?

  How can I make my cd Rom drive working again?
  How can I fix the error?

  Could guide you me in registry change (upper and lower filters) if necessary?

  Post edited by: GRIX

  Hello

  Check please follow thread - http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=68988

  Here, you can find the solution to your problem.

• DesignJet 111: DesignJet 111 - printing problems - no printing after upgrading to Windows 10

  Several problems to the upgrade of WINDOWS 7 for WIN 10.

  The HP DesignJet is 'offline' and can't figure out how to change the setting of "online."

  The definition "print directly to the printer" is not.

  Yellow flashing on the printer dashboard - magenta ink cartridge shows empty, but it is full.

  Computer HP printer installed - poster is in the Device Manager - watch "this device is functioning."

  Printer is listed in devices and printers.

  HP Support Assistant doesn't recognize - printer in the list, can not find device during an attempt of "add design.

  Printer turns off or recycle off on after turning on.

  Hello

  If you have a driver problem:

  Remove the driver completely from the computer, then download and install the lates driver.

  Here is the link incase you need

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4123145 & swLangOid = 8 & swEnvOid = 4192

  Now, the yellow light flashes on the Panel means that the printer needs attention, like:

  -Close coverage which is open

  -Of paper

  -Paper tilt

  -Jam

  -An error code

  If you have 6 columns on the levels of ink instead of 4 is because you have an error code.

  On the following link, you can find more information on how to prepare the error codes

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=352387 & docid = emr_na-bpp03841

  If you have an error code, the printer appears offline on your computer.

  On this other link, you will find how to check other messages on the printer

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01669949

• Connection problems wireless Broadcom 1704 after upgrade to windows 10

  Connectivity problems after upgrade to windows 10 intermittent wireless;  Have an Inspiron 5748 with adapter Broadcom 1704.  Driver is up to date: 7.35.295.0.  Diagnostic shows no problem with the unit.  Will be generally connect to the network, but the connection is deleted intermittently.  Troubleshooting to solve using leads to restore connectivity, but it will then drop again intermittently.  Never experienced problems before windows upgrade 10.

  steveshuff,

  Here are a few parameters to change on your adapter wireless for better performance.

  Turn on and off then on all devices on the network

  1. Turn off the power to the broadband modem and let the modem broadband disconnected for at least 3 minutes.
  2. Shut down all computers that are connected to the network.
  3. Remove power from the wireless router.
  4. Check that a network cable is connected the modem to broadband in the Internet or the wireless router's WAN port.
  5. Check that no series cables or USB are connected to the Modem on broadband.
  6. Connect the power supply to the modem broadband. Wait at least 2 minutes for the Broadband Modem to initialize.
     (If the Modem does not provide Internet connection successfully, unplug the Modem. Wait at least 5 minutes, then plug the Modem back.)
  7. Connect the power supply to the wireless router. Wait at least 2 minutes for the wireless router to initialize.
  8. Turn on the computer and try to connect to the Internet.

  Difficulty of wireless network connections

  Turn off airplane Mode

  For Dell Wireless adapters:

  1. In the Search box, type Device Manager.
  2. Press or click (Control Panel) Device Manager.
  3. In the Device Manager window, click on the sign of the arrow next to network adapters.
  4. Double click or double-click the Référence Dell Wireless WLAN Card.
  5. Click the Advanced tab.
     Note: These options are not available according to the installed wireless adapter.
  6. In the property: box highlight AP Compatibility Mode, select broader compatibility under value: from the menu drop-down.
  7. In the property: box, highlight the Minimum energy consumption, select disabled under value: from the menu drop down.
  8. Click OK.

  For me, to help troubleshoot, please click on my DELL-Jesse L and send me a private Message with the number of Service Dell and your Dell order number.

• I will face any hardware problem after upgrade to Windows 10?

  Original title: upgrade Windows 10

  I have a Dell Vostro 1015 running windows 7 Professional. I am considering upgrading to Windows 10. Please advise if there are problems if I upgrade any hardware after upgrade to Windows 10, e.g. upgrade or downgrade RAM.

  Hello

  Thanks for posting your query on the Microsoft Community.

  With the description, I understand that you want to upgrade your Windows 7 operating system Windows 10 machine. I will certainly help you get this fixed number.

  I suggest you refer to the mentioned Microsoft articles below and check if this is useful:

  Upgrade to Windows 10: FAQ

  http://Windows.Microsoft.com/en-us/Windows-10/upgrade-to-Windows-10-FAQ

  Hope the helps of information. Please write back to us for any further assistance. We will be happy to help you.

• HP ProBook 450 G0: Problems of HP ProBook G0 450 icons after upgrade to Windows 10

  Hello

  2 days ago that I have upgraded to Windows 10 my HP ProBook 450 G0.

  Then I realized my graphics drivers are not working, I tried to update to the last registered in the section to download the drivers for my model.

  After that, I got BSOD and couldn't even see login screen. I removed the update installed in safe mode.

  If at the moment I use some default driver I guess.

  In the Device Manager on Intel(r) HD Graphics 4000 I something like (manual translation) "Windows has stopped this device because of disorders raported. (Code 43) ».

  I can't use the HDMI & display internal. To use the HDMI, I have to restart my PC. After using HDMI, I can't use internal display. A lot of questions, because this driver...

  I really need this, as I am a teacher and I ', using both internal display & HDMI for presentations...

  All solutions? All the newspapers that I can get to help you help me ?

  Kind regards

  Jakub Krol.

  Hello

  In case anyone is interested, my PC is now fixed

  More information: https://windowsforum.com/threads/graphics-issues-after-upgrade-to-windows-10-system_service_exception-sgfxk64-sys.220205/page-2 .

  Kind regards

  JK.

• Satellite A300D-15B - Webcam does not work after upgrade to Windows 7

  My webcam does not work after upgrade to Windows 7. I installed the drivers but still having no luck

  Hey Buddy,

  What does it mean exactly when you say he won t work?
  You get an error message or only a black image? What model of laptop you have and that you use the Toshiba Windows 7 upgrade kit or a disc of Microsoft?

  At this moment I can only offers to install latest driver of the webcam of the official website of Toshiba. Make sure that this driver is released for Windows 7 and not Vista.

• Satellite L30 - frequent BSoD after upgrade of RAM.

  This problem is almost identical to [this post | http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=144540𣒜], but given that the response was too general and did not help, I want to provide more details about my problem and hope for a better answer.

  My L35 (i.e. American L30) came with Vista Home Basic and only 512M of RAM. It was slow, but smooth otherwise. The problems started after I upgraded the RAM to 2 GB occasionally a BSoD will appear, and the computer restarts after a second or two.
  Most of the time, instances of BSoD are not taken at random; usually, it happens when you watch a film or multimedia and online during the wake her up after suspend.
  Also, it happens much more frequently if an external monitor is attached. He does, connect an external monitor and watch a movie will result in BSoD with 100% certainty. My laptop has shared video memory, maybe it's a question here.

  The problem prevailed after that I installed Windows 7.
  Memtest86 + showed no problems with my memory
  Memtest86 covers all aspects of the use of the RAM?

  Is it possible that some problems may be overlooked by memtest86?
  Are there other tests of memory, that I could use, specifically to test the shared video memory?

  Not every hardware problem can be detected software.
  You have tested the RAM with Memtest86 +? Try using Memtest86 (no +).

  In the worst case, you must replace the RAM. Ask the dealer for a new computer. I m sure they will help you.